Search Documents

By G Bickert

Australia is currently developing and engineering a range of specialised processing options for rare earth (RE) (Lynas, 2011, Alkane, 2005), zirconia (Alkane, 2005), lithium (Galaxy Resources, 2008) and other special minerals and metals required in high-tech applications. The processing of lithium, zirconium and RE minerals is based on complex leaching processes which require extensive liquor clarification, solid liquid separation and solids washing. The filtration properties for those leach liquors, residues and precipitates are not well understood and differ drastically according to the process route applied. Thus, filtration test work is essential for equipment selection, sizing and design. Similar types of slurries are filtered in laterite nickel, TiO2 and other chemical oriented processes, while more experience is available here as those processes are applied widely for a number of decades. The increasing need for dry stacking of tailings requires advanced tailings filtration with properties differing drastically depending on tailings properties. More traditional mineral processes such as flotation commonly apply filtration. All of these and other cases require proper filtration test work particularly evaluation of vacuum versus pressure filtration and the need for cake pressing and/or air blowing for filter presses. Bench scale test work and/or pilot plant operation is common to determine filtration rates, achievable cake moisture and wash efficiencies and sometimes filtrate clarity. While those values are important, there is much more valid information to be obtained by filtration test work.This paper discusses the intricacy of filter selection and sizing based on driving forces (vacuum and pressure air, compression by mechanical means and slurry) and parameters (cake thickness, forces and times) and different processes utilised in common filtration equipment. It will discuss the in’s and out’s of filtration test work design, planning, and in particular data gathering, processing, reporting, evaluation and filter sizing from recent examples of bench and pilot scale filtration test work for above applications together with methods for predicting filtration performance for example where test work is lacking. One focus will be the realistic extrapolation of test work results towards different parameters utilised in full scale equipment and plants. The conclusion of the paper will contain checklist for filtration test work.

Aug 8, 2011

Two main aspects need to be considered when analysing a potential petroleum development project. Firstly, an estimate of the recoverable reserves must be made, and in many instances, these reserves must serve as collateral to finance development if outside capital is required. Secondly, the likely production profile and cash flow has to be established, and this cash flow then must meet debt service require- ments and in addition generate the required profits. In making these crucial deter- minations, the impact on the project of a wide variety of risks has to be analysed. A computer model, which represents the project in its entirety, is a great aid in determining project viability. Such a model requires imput from geologists, engineers and economists, and interpretation of the model must also be a joint effort. Communications, and inter react ion amongst individuals and disciplines is essential if the best answers are to be obtained

Jan 1, 1983

By R Berry, S G. Walters, J A. Hunt, D Collett

The texture of an ore type is fundamental in understanding the metallurgical behaviour of an ore. This study will show examples of how quantified textural attributes (mineral shape, grain size and mineral association) can be obtained from automated and scanning electron microscope (SEM)-based microscopy and utilised using advanced image processing techniques. Examples will be shown of integrating quantified and semi-quantified meso- and macro-scale textural attributes as well as how they relate to texture-based visual logging systems. The implications of texture for processing behaviours such as comminution, liberation and recovery will be discussed. This research is part of a major collaborative geometallurgical project undertaken at the Centre of Excellence in Ore Deposits (CODES, University of Tasmania) and the Julius Kruttschnitt Mineral Research Centre (JKMRC, University of Queensland). The authors wish to acknowledge financial support and permission to publish from the sponsors of the AMIRA P843 GEMIII project.

Jan 1, 2008

By P Kittler

In the spectrum of mining-related disciplines, geometallurgy sits between resource geology and metallurgical engineering. Unlike its neighbours, it is a relatively young discipline and its concepts, procedures and techniques are still evolving. Relevant geometallurgical issues differ from one deposit to the next so there is no single template that can be used in all situations, meaning that geometallurgy programs are nearly always customised and tailored to the deposit and the situation.Over time, a number of key mistakes are seen to emerge regularly. The eventual impact of these mistakes can vary from suboptimal performance of mine and plant to complete failure of the operation. For instance, poor characterisation of ore lithologies and their spatial distribution can have negative impacts on processing plant throughput. However, when combined with failure to identify critical blending constraints it can result in a totally inoperable plant.A number of common mistakes committed during geometallurgical programs are discussed and some preferred alternative approaches are suggested

Sep 5, 2011

TSL Concepts and Practical Examples of the Non-Reactive System - Meyco TSL 865 Thin Spray-on Liners (TSLs) have been intensively investigated by mining and chemical industries within the last decade. Apart from the basic concept of spraying thin liners, expectations of the product's performance vary, eg immediate active strata support is seen as a key to control the ground permanently. For many coal mines this is an important factor to reduce maintenance in their roadways and enable permanent production from the long wall. In opposition to a passive mesh system this technology offers immediate active support to the strata. But not only coal mines are interested in TSL technology, there are potential applications in hard rock mines, during shaft sinking, pillar support and as an anti-weathering sealant. This paper will explain the advantages and disadvantages of TSL concepts; it will give examples of successfully applied TSLs with a main focus on the non-reactive and flexible system MEYCO TSL 865 by BASF. Furthermore, it will indicate the limitations and discuss briefly the bearing capacity and reasonable lab testing of such systems.

Nov 25, 2010

By P Viljoen, A Holland, C Parken

In the raisebore industry, there are two known methods of removing large diameter reamer heads once the reaming of an underground shaft is complete: 1. Lower the reamer head to the base of the shaft and use a thermal lance to cut the drill string and drag the reamer away from the hole. This method exposes the person doing the job to falling rocks from the unsupported mineshaft, a hazard which is difficult to control and has caused fatalities. 2. Install breast plates in the backs above the reamer head at the top of the hole, and use air hoists to lift the reamer out of the hole. Steel beams are then placed across the hole which the reamer is lowered down onto, dragged forward away from the hole, disassembled, and removed. This method is time consuming, expensive, and complex in the controls required to ensure safe completion of the job At Carrapateena, the air hoist method had been successfully used, however, with the cost involved and the complexity of this process, development of an improved and fit for purpose reamer removal method was pursued. OZ Minerals collaborated with Pybar to develop an industry first application of Enerpac SL100 lift and shift technology; a track mounted system with hydraulic lifting units that can both lift the reamer out of the hole and tram it back along the tracks away from the hole. A key component of turning the idea into a reality was by establishing a truly collaborative relationship between client and contractor. When the SL100 mobile gantry arrived, it was set up in Adelaide and trialled with the whole raise bore crew attending the two-day workshop and risk assessment; a rare opportunity for drillers. There have now been five successful reamer removals with the SL100 mobile gantry at Carrapateena. It has proven to be an efficient process with the entire process from setup to demobilisation taking less than 48 hours. This new way has completely removed hot works and uncontrolled hazards from working at the bottom of a shaft. It has also saved the reamer stabiliser from being cut and thus wasted. Exposure to the open hole has been minimised significantly as assembly of the SL100 is completed well forward of the open hole. This new process is exponentially safer, quicker and cheaper.

Mar 15, 2021

By D A. Sims

This paper outlines the contributing factors to a series of erroneous Mineral Resource estimates which led to considerable loss, including significant reduction of mine life and consequently a large write-down of asset value. The error prompted divestment of the mineral asset in the short-term by the owners, a major mining company. There were multiple and complex contributions to the result: • The mine was undergoing a transition in the deposit geology with increasing depth that was not accommodated in the models. Early indications of the geological transition in initial drilling were generally unrecognised in resource modelling. The shortcomings of the models became apparent with increasing infill drilling and subsequent production reconciliation. • There was a lack of recognition of, and confidence in, site-based input and skills by corporate technical management. The site had a reputation internally for over-delivery to plan early in its life and that supported the anticipation of ongoing metal delivery into the mine plan by management. • A corporate lack of confidence in site being able to adequately domain the mineralisation led to the use of a CIK domaining process, rather than one which was geologically based. This domaining process led to gross over-statement of mineralisation trends reflected in the subsequent OK estimate. • Timelines on the outsourced estimation process were so short that validation was not possible. Obvious errors in the estimate versus data were not able to be used to correct the issues and the site’s Competent Person sign-off occurred without adequate checks. This case study is presented to reinforce the concept that Mineral Resource estimates are not solely based on the ability of the Competent Person to satisfactorily guide the process. There are usually multiple complex issues in the estimation process which need to be recognised and considered in judging reconciliations of model to actual.

May 24, 2023

By Davison GR

The cost of drilling consumables is always a large component of any mine budget. It is important that this cost be carefully examined with a view to reducing the overall cost per inetre or at least minimising its escalation.At Renison it is considered that the only way to ensure drilling costs do not rise unduly is through a total system of control from purchase to disposal.In 1979 extension of an existing drill supply service contract was carefully examined and abandoned in favour of a hybrid system. This system is providing a great deal of control over the use of drilling consumables and has maintained a relatively constant cost per drilled metre over the last five years.Current consignment stock contracts for drilling consumables are strictly specified by the Technical Services section of the Mine Department and consumables purchased under these contracts are distributed and refurbished/sharpened by a contractor.The total result of this package is individual drilling items that achieve the best cost per metre and careful distribution and maintenance to ensure maximum life.

Jan 1, 1985

By D Brett

The Paper presents the authors thoughts on how the mining industry should be improving the education of site personnel so they can provide a greater level of effective control of tailings dam safety including empowerment to develop their own documentation, monitoring and surveillance systems and to better liaise with specialist external technical staff or consultants.

Jul 1, 2021

By Hikosaka A, Chiba A

In a fundamental study of the physical chemistry of steelmaking slag, equilibra bet- ween hydrogen-water vapour gas mixtures and liquid slags contained in solid iron crucibles have been measured for four binary slags, FetO-CaO, FetO-Si02, FetO-TiO2 and FetO-Al203 at 14000C. From the data, the activity of iron oxide and the ratio of ferrous and ferric ions (A = Fe3+/Fe2+) were calculated for the slag composition. The best ionic model is found to be that based on regular solution of cations. The oxygen distribution between slag and metal is quantitatively expressed by this model over a wide range of slag composition.

Jan 1, 1980

By M Ogle

"Booster fans are relatively rare in Australian coal mines. However, as mines become progressivelydeeper it is likely that such fans will be increasingly adopted as a method to sustain or improve the ventilation of underground workings. The reasons why booster fans may be an att ractive alternative include: increased cost of sinking additional ventilation shafts with greater seam depths; environmental objections to shaft sinking projects; and increasing urbanisation and surface constraints limiting availability of potential ventilation shaft sites. As Tahmoor Colliery movedinto its northern lease the ventilation constraints became the limiting factor on production. Thelimitations of the old workings meant that the existing ventilation system would be inadequateto sustain the required production. Extensive ventilation modelling was carried out to evaluatevarious potential solutions and the recommended option was the installation of a booster fanor fans, to gain underground access to an already approved shaft site in the northern lease.Proposals were sought from recognised fan manufacturers and various alternative arrangements were tendered. Ultimately the choice was between one large centrifugal fan and a set (three or four) of smaller æauxiliary-likeÆ fans in parallel. The successful tender was for a single centrifugal, an arrangement very similar to the booster fans that have been operating eff ectively at Westcliff Colliery for a number of years. This paper describes the current ventilation network, evaluation of the ventilation options, the fan selection process, and the project status to date."

Jun 1, 2012

By G W. Wilson, C Panidis

Potentially acid forming (PAF) waste rock contained in dumps formed as a result of open cut mining of metalliferous orebodies are conventionally sealed or covered using a near-saturated, low permeability compacted clay layer, protected with a mulch layer and/or vegetated growth medium. The purpose of the compacted clay layer is to limit oxygen diffusion and the infiltration of rainfall into the dump. Where the aerial extent of the PAF waste rock dump is large, or where suitable clayey material is in short supply, it may be difficult to source sufficient suitable clayey material to form the cover. The paper describes a laboratory-based investigation of combining inert waste rock and tailings to form an alternative seal or cover material. The inert waste rock was sourced from the trafficked surface of a non-acid forming (NAF) waste rock dump, with a maximum particle size of about 100 mm. This was combined with NAF thickener underflow tailings slurry in various mass ratios, and the resulting mixtures tested for their particle size distribution, compaction characteristics, soil water characteristics (relationship between suction and volumetric moisture content), and saturated hydraulic conductivity. The mixtures tested ranged in consistency from those dry enough to be compactable, to those with the consistency of wet concrete that lend themselves to placement without the need for compaction. The laboratory test results showed that the suitability of the mixtures as seal or cover materials is very dependent on the particle size distribution of the mixture, with well-graded mixtures having substantial fines performing best.

Jan 1, 2003

By J P. Burr

The Waterview Connection will complete a strategic Auckland motorway route linking the south, west and north. The project will include 2.1 km of ‘undrained’ driven tunnels, 500 m of drained cut-and-cover tunnel and tunnel portals.The project is aligned beneath a stream valley of Oakley Creek, which is incised through alluvium and in places overlain by landfill, between Mt Albert volcano and a ridge formed in alternating sandstones and siltstones. The resulting topography, geology and hydrogeology of the tunnel alignment are complex.The Assessment of Effects required estimation of the likely settlements resulting from the tunnel construction and assessment of their effects on the buildings, services and other features. A conservative approach was taken when estimating settlements in order to provide an upper bound estimate of the consequent effects. There are three sources of these settlements: mechanical settlement from the tunnel excavation, mechanical settlement from the displacement of retaining walls and consolidation settlement from the groundwater drawdowns during construction and, in some cases, in the long-term.The settlements from these sources were calculated independently and then combined to identify the most critical effects. These combined settlements were used to assess the potential damage to the buildings, services and other features above and around the tunnels. The combined settlement results generally followed the anticipated trough shape centred on the underlying tunnel but with some noticeable effects relating to the underlying geology and hydrogeology.The effects on buildings were typically assessed as negligible with some areas of very slight to moderate damage predicted. Effects on services are anticipated to be minor but some large and older pipes will require specific monitoring during construction. A monitoring programme is proposed to allow the actual settlement and effects to be compared to those estimated with appropriate responses should those effects significantly differ.This paper describes the methods used to calculate and combine the settlements and assess their effects.

Mar 8, 2011

In the future, Illawarra Coal, the primary metallurgical coal producer in the southern coal fields of New South Wales, will face many unique challenges not found in other coal or minerals production areas. To manage these challenges and determine the best strategy for the business, Illawarra Coal has adopted a systematic strategic planning process, which starts from the broadest possible options analysis and culminates in a ægo-forwardÆ operating case that individual mine sites use as the basis for short-term planning. This paper will discuss two major topics. Firstly an overview of the Illawarra Coal and BHP Billiton strategic planning processes. This will demonstrate the range of variables and inputs that are required for the planning process, and the system which is followed to evaluate different alternatives for the extraction of the resource. Secondly, having discussed the primary external and internal factors that must be accounted for in the planning process, and the main issues affecting the viability and likelihood of each alternative, the paper will discuss the particular challenges that Illawarra Coal will face in the coming decades. These challenges include: market and price uncertainty; managing impact on surface features, infrastructure and environment; community interaction; transport and logistics constraints; unknown mining environments; lack of geological knowledge; limited surface access for new mining domains; changing attitudes to longwall mining in the Illawarra; ageing workforce; and cost and overhead management. The paper intends to discuss how these issues impact the business currently and how they are incorporated into Life of Asset plans and overall corporate strategy for Illawarra Coal.

Jan 1, 2007

In the last two decades, equipment used in the coal mining operations has become much more sophisticated. The way that work is organised and performed in the industry has also changed significantly. Changes in equipment specification or procedures inevitably means that the risk associated with that equipment or procedure also changes. In an attempt to address this the Joint Coal Board Occupational Health and Safety Trust (JCB) commissioned the University of New South Wales Mining Research Centre and Mine Site Technologies to perform a feasibility study into the development and deployment of Virtual Reality (VR) based training simulators in the New South Wales coal industry. The main aims of the study were to identify, the key providers of VR Technology, the VR options available to the JCB and the information that would need to be included in any simulator. It was anticipated that a critical assessment of these components would produce a format for a cost effective, state of the art simulator that could be readily accessed by all mines. The expectations of the feasibility study were that VR should offer three-dimensional (3D) simulations that are interactive, high-resolution models of real environments based on best practice Safety Management Plans. It was anticipated that the simulations would allow trainees to experience the consequences of poor decision-making and allow them to learn from their mistakes in a safe and forgiving environment. It was envisaged that such simulators would become an addition to the existing training methods used in the industry.

Jan 1, 2003

By Sorokin M, Komkov A, Fyodorov A

The Vanyukov Process is a high-intensity smelting system that has been proven over the last 20 years for various metallurgical operations including the smelting of copper, nickel, copper-zinc, antimony concentrates, municipal waste treatment and pig-iron production. Extensive pilot plant tests on copper and copper-nickel concentrates have provided information for the design of the commercial furnaces. The thermodynamic analysis, design idea and the data obtained from commercial furnaces have shown that Vanyukov Process would be the best choice to smelt copper-nickel and nickel sulphide concentrates as well as oxide nickel ores.

Jan 1, 1996

The treatment of nickel ores and concentrates and the subsequent processing to recover separate products of nickel and cobalt is one of the major interests at present in the mining industry. The increasing demand for nickel, and more recently also cobalt, has led to increased exploration for ore sources. Major discoveries have resulted in Canada and Australia. These deposits, as well as others already known, are presently being developed and the process technology tested and evaluated for applicability to the different mineralogical types - mainly sulphide, arsenide and oxide laterites. Concentrates may be treated by either hydro- or pyrometallurgical processes, while the nickel laterites are best suited to hydrometallurgical processing. However, if hydrometallurgy is used, once the ore or concentrate is leached the resultant solutions are then amenable to similar separation technologies for purification and recovery of high purity nickel and cobalt products. Solvent extraction, together with other separation processes such as precipitation, can produce high purity solutions of nickel and cobalt. The final products of these solutions may be nickel and cobalt cathodes, metal powders precipitates or salts, depending on the final process of electrowinning, hydrogen reduction, precipitation, or crystallisation Respectively.

Jan 1, 1996

Comminution of solids is surely one of the oldest technologies which even in this day and age of DNAs, chips and space exploration continues to challenge our scientific acumen and engineering ingenuity. In essence, this challenge is two-fold. One, as much as three to four per cent of all electric power generated world-wide is consumed in crushing and grinding primarily because the utilisation of energy is woefully poor. Studies have shown that the efficiency of mechanical size reduction processes is of the order of 1.5 to 12 per cent only (Schoenert 1986). Two, with the grinding technologies available to us, we have, at best, inadequate and, at worst, almost negligible control over the shape of the comminuted particles, size dispersion of the ground mass, and the sharpness of mineral liberation. Low energy efficiency and lack of control in the sense mentioned above have far-reaching implications for resource conservation, performance of down stream unit operations, and damage to the environment. Our problem is in fact central to the mineral-energy resources triangle shown in Figure 1 which depicts the close interrelationships among mineral resources which are becoming poorer in content and more complex in mineralogy each day, energy resources which are depleting rapidly without any viable alternate on the horizon, and environmental concerns which can no longer be ignored. It is evident that any improvement in the efficiency of the comminution process impacts directly on the control of environmental damage, conservation of energy and the economics of the operation. These concerns have special relevance for the processing of non-ferrous ores.

Jan 1, 1992

By S Shipard

Filters are used in water treatment and hydrometallurgical process plants for objectives such as generating a dry spadable solid, pumpable high density slurry or high purity filtrate. The priority objective of every polishing filter, sometimes also termed clarifying filters is high purity filtrate and these are found in many diverse industries and even different applications within the same industry.To generate a high purity filtrate, process designers have the choice of many different polishing filter products, but in reality very few polishing filters are based on fundamentally different filtering concepts.This paper reviews the technology merits of well-known and the more recently developed polishing filter products and aims to assist metallurgists and engineers with the selection of an appropriate polishing filtration technology for pregnant liquor filtration and other process applications, plus a guide to best practice.CITATION:Shipard, S, 2013. Polishing filters for mineral processing plants, in Proceedings MetPlant 2013 , pp 118-125 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

Optimum selection of explosives by means of monitoring explosive performance can lead to increased profitability through the control of fragmentation, a reduction in hangingwall and footwall damage and overall drill and blast costs. Studies conducted at the Mount Lyell Mining and Railway Company underground copper mine evaluated in situ the performance of four explosive types. Measurements included monitoring the levels of induced shock energy and the attenuation thereof with distance. The velocity of detonation (VOD) of these explosives was also measured using in-hole techniques. Assessment of these results, together with a knowledge of the rock mass strength, facilitated the selection of an explosive that was best suited to the given rock mass conditions.

Jan 1, 1995