Search Documents

By Williams DJ

Preliminary calculations suggest that spoil piles in the Bowen Basin will undergo approximately 4 m settlement as the ground water table recovers after mining is abandoned. Approximately 1 m of differential settlement is possible. Superimposed on this will be a long term creep settlement of 1-3 m/log cycle of time. Depending on the nature of the spoil material, partially submerged spoil piles could be sufficiently stable although to ensure stability during long term creep it may be necessary to flatten the final spoil pile face to approximately 25¦.

Jan 1, 1987

By Baynes F. J, Bermingham A. G

The 6000m long King Headrace Tunnel will be driven through hard Owen Conglomerate in the Eastern third and feldspar porphyry in the Western two thirds, with the anticipated hardness up to 350MPa unconfined compressive strength. Since the Commission had not driven a long, large diameter tunnel for some twenty years, major research was undertaken to assess the current tunnelling trends. Tunnel boring machines were compared with drill and fire equipment. Rail equipment was compared with rubber tyred equipment. Tenders were called with tenderers invited to submit alternatives if desired. Commissioning and production excavation using the equipment is discussed with the final conclusion being that the individual items of equipment purchased combined to make an efficient hard rock drill and blast system capable of progressing through all rock conditions likely to be encountered on the King and Anthony Schemes.

Jan 1, 1987

By H Lemos, E Nunes, D Jacobson, R Costa, L Ono, A Alves, H Delboni Jr

Oversize rock breaking and metal tramp removal are key issues for reducing primary crusher downtime, as well as improving the safety associated with its operation. Remote operation of such tasks would thus not only increase productivity, but also reduce the risks related to work in confined spaces, fall risks, and overhead hazards. These issues are particularly relevant in high-capacity operations such as iron ore mining, where large machines are in continuous operation. This article describes the architecture, construction and advanced testing of a novel remotely operated robotic mechanism for assessment and removal of metal tramp from primary crusher chambers. The system essentially includes a robotic-arm equipped with a hydraulic clamp tool for handling oversize material, as well as an oxy-flame module for cutting metal pieces entrapped within the primary crusher cavity. The first industrial unit was delivered to a large iron ore mine in Brazil, where the installation and testing is scheduled within the coming months.

Nov 8, 2021

By K Katov, S T. Ciutina, J D. Pyke

The development and optimisation of mill discharge trommels, and specifically their screen panels, can be a neglected area in the complex operation of a minerals processing plant. Trommels are often seen as a ‘set and forget’ component of the circuit, even when significant improvements in design are possible. A redesigned trommel and panel arrangement has simplified and added flexibility to the plant shutdown schedule at Kirkland Lake Gold’s Fosterville Gold Mine in Central Victoria.Prior to the trommel redesign, the shutdown frequency was determined by the expected life of trommel panels at 14 weeks. Planning downtime around this item led to higher maintenance costs and wastage in other areas of the plant. This was particularly disruptive with respect to mill lining change-outs, which were forced out of sequence and often changed prematurely. Fosterville Gold engaged Metso Australia Limited to propose a new trommel design that would better suit the site. The new trommel was engineered to balance simplicity with performance, and incorporated the latest in Modular trommel design, modelling and Finite Elemental Analysis (FEA). Modular Panels and Spiral Segments achieve significantly longer life, and allow in-situ panel change outs, flexibility in spiral and dam positioning and an improvement in classification performance. Trommel panel life has significantly increased from 14 to 71 weeks in the trommel’s highest wearing zone. The new design has eliminated some risks to safety by reducing manual labour and lifting requirements during shutdowns. There is greater flexibility with respect to shutdown requirements. The site is no longer at the mercy of trommel panel lifespan, which allows for better optimisation of wear components in the circuit. CITATION:Pyke, J D, Katov, K and Ciutina, S T, 2018. Modular SAG mill discharge trommel for maintenance flexibility and performance, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 613–620 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By D R. Andrew, K T. Morrison, J F. Tiedgen

Waste blasting in iron ore operations can pose a number of technical challenges, including blasting through variable geology and blasting soft ground in wet conditions. Blast patterns are designed to be loaded with a specific range of explosives with unique characteristics and properties. Each explosive product will produce an optimal blast outcome for a given set of blast parameters and ground conditions. Sites characterised by softer rock typically require low-density, low-energy explosives. Historically, these products have contained a high ratio of porous ammonium nitrate prill and are only suitable for dry blastholes. When blastholes within a pattern are found to be unsuitable for such explosives due to wet, damp or muddy blasthole conditions, a new product is selected. While it is easy to switch products to match blasthole conditions, the different properties of the new non-ideal product can impact blast performance and increase loading times and costs.Flexigel™ is a solids-sensitised emulsion blend suitable for loading at variable densities and energies in dry, damp, muddy or wet blastholes. It is a universal product that can be loaded to match ground and blasthole conditions or complement other explosive products.At Fortescue Metals Group’s Cloudbreak site, Flexigel™ was trialled through a series of matched pair blasts in order to optimise blast outcomes in conditions that were non-ideal for existing explosive products and to reduce the overall cost of drill and blast operations. Flexigel™ yielded improved instantaneous dig rates and improved loading efficiency when compared to a traditional emulsion blend. The results also indicated that variable-density and variable-energy products afford greater flexibility for optimising blast outcomes across all ground and blasthole conditions trialled.Trials of Flexigel™ at Cloudbreak have shown that a variable-density solution is available for conditions where traditional explosive products are non-ideal. As such, Flexigel™ is able to fill a major void at any operation where the desired low-density, low-energy explosive product must be substituted for a more expensive traditional emulsion blend or heavy ammonium nitrate/fuel oil.CITATION:Andrew, D R, Morrison, K T and Tiedgen, J F, 2015. Flexigel™ – a variable-density solution, in Proceedings Iron Ore 2015, pp 413–418 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By Sun Y. L, Jiang J. J, Lu S. L

A distinguishing feature of tunnels in squeezing rocks is that a large deformation of the surrounding rocks takes place slowly and gradually, often called squeezing phenomenon. It is different from the rocksbursting phenomenon during which the deformation of tunnels occurs instantaneously when the resulting stresses exceed the strength of the surrounding rocks. The squeezing phenomenon has received great attention in the field of rock mechanics and tunnelling recently. The mechanism and various factors related to the large deformation and failure of tunnels in squeezing rocks are discussed in this paper on the basis of field investigations and laboratory model tests. The relationship between the deformation of surrounding rocks and support of the tunnels in squeezing rocks is presented in the form of numerical modelling.

Jan 1, 1995

By D Felipe, G J. Harbort

In the past 40 years substantial changes have occurred in flotation machines. This has included increases in mechanical cell size to 630 m3 , significant changes to flotation column aeration design and widespread use of the Jameson cell and other pneumatic flotation cells. Over the corresponding period there has been increased used of machine characterisation measurements to benchmark and optimise flotation circuit performance. JKTech maintains a database of industrial flotation machine characterisation measurements. The database contains over 4000 entries and includes gas dispersion measurements, such as bubble size, gas hold-up and superficial gas velocity, cell dimensions and impeller tip speeds. Data comes from numerous operating sites and commodity groups, including gold, copper, molybdenum, nickel, palladium, lead-zinc, platinum, silica, phosphate, coal and iron ore. Flotation duties registered include flash flotation, preflotation, roughing, scavenging and cleaner circuits. Measurements have been conducted on a wide range of flotation machines from different manufacturers. This includes forced air machines, such as Outotec and Dorr Oliver, and self-aerated machines, such as Denver and Wemco. The database also includes substantial flotation column entries, such as the Microcel, Eriez/CMT Slamjet and Jameson cell. This paper describes the flotation machine characterisation database and discusses the variation between different types of industrial flotation machines, in operating production circuits.

Aug 24, 2022

By W Stange, N Hanson

An important aspect of the project evaluation process is the achievement of a clear and quantitative understanding of the primary drivers influencing project value and risk. A business scenario-based approach is required to ensure that the project meets value and risk hurdles over the short, medium and longer term. Adopting an optimising approach can aid significantly in the development of a project concept into a business that is optimal and sustainable in the longer term. Through the application of case studies, based on work performed with various mining organisations during the last five years, this paper will demonstrate how project value and robustness can be optimised. Experience has demonstrated that applying this approach results in significant value improvements and risk reduction û primarily by application of a rigorous, fact-based analysis and optimisation process that rapidly increases management team understanding and insight of key driver of value and risk.

Jan 1, 2007

By Barlow S

The Kelian Gold mine project won two excellence awards from the Victorian Division of the Institution of Engineers, Australia. It was a challenging project, fast tracked in a remote and inhospitable tropical environment. The creation of a profitable and efficient mine was a significant engineering and project management achievement. The difficulties encountered and the way they were managed provide valuable lessons. These include the importance of sufficiently detailed engineering in all aspects of the job to enable the best estimates possible to be prepared during feasibility studies, the need to prepare the project scope and execution plan with disciplined and rigorous attention to detail by a highly experienced team and the value of identifying, assessing and mitigating risk and uncertainty during execution. The practical benefits of applying these lessons were demonstrated in the successful management of technical uncertainty on the recent diversion of the Kelian River to allow the expansion of the Kelian mine.

Jan 1, 1997

By Singer RP

The Latrobe Valley brown coal deposits are one of Australia's major energy resources with measured and indicated reserves amounting to some 162 billion tonnes. Economically recoverable reserves are estimated at some 65 billion tonnes, 47 billion tonnes of which are classified as available for mining (VBCC (1983)). These deposits contain one of the lowest grade fuels used anywhere in the world. Typical Net Wet Specific Energy values range from 6 to 9 MJ/kg. Despite the low energy value of the raw coal, the Latrobe Valley deposits represent approximately 90% of Victoria's indigenous non-renewable energy resources. Utilisation of this vast primary energy resource has been a key factor in the economic development of Victoria.

Jan 1, 1990

By R Jaine, D Strang, M Fowler

"This paper presents a case study demonstrating active geotechnical pit slope management at the now completed Carina Iron Ore Project operated by Mineral Resources Ltd (MRL). The site is located 105 km north-east of Southern Cross, Western Australia. The paper is primarily focused on the slope stability failure modes and the remedial measures employed to maintain mining.Between a quarter and a third of the excavated slopes were impacted by some form of instability that was beyond expectations of the intended slope design criteria and common practice. Ongoing mining was supported by intensive geotechnical pit slope management including close cooperation between geotechnical, mine planning and operations staff to achieve timely and practical mining solutions.Mining encountered varied slope failure mechanisms which required a combination of remedial solutions comprising: horizontal depressurisation holes, deferral of excavation, unloading, buttressing and catch berms.The root cause of the challenging slope performance was a mismatch between the predicted and encountered geotechnical model, resulting from a failure to recognise the critical mechanisms that control slope stability.Despite the extensive zones of instabilities at completion of mining, full ore recovery was achieved without major delays and in a controlled and safe manner.Citation:Fowler, M, Strang, D and Jaine, R, 2016. Adapting to Geotechnical Change - a Case Study of the Carina Open Pit Mine, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 150–161 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By S Strong, L I. Sanz Vivanco, T Brown

One of the most significant technical and practical challenges facing the tunnel construction team on the Legacy Way road tunnel project in Brisbane, Australia was how to erect the prestressed precast concrete slabs to form the smoke duct in the tunnel boring machine (TBM) tunnels.An essential part of the tunnel ventilation system, the smoke duct extends the full length of the 4.6 km-long twin two-lane tunnels. The vast majority of the tunnels (approximately 4.3 km) were constructed using two 12.4 m diameter double-shield TBMs. The refurbished Herrenknecht machines broke several world records on the way to completing the tunnel excavation works in just over nine months. With the excavation complete the focus turned to solving the complex civil tunnel fit-out challenges. A key component of the civil fit-out of the tunnels was constructing the smoke duct in the TBM tunnels, which was designed as a precast solution.The slabs, which each measure 8.62 m long × 2.0 m wide × 200 mm thick and weigh close to 9?t, need to be erected above cast in situ corbels whilst other tunnel finishing works continue. The space-proofing clearance offered by the design to the support corbels below and the precast segmental lining above was in the order of only 100 mm.This paper tells the story of how the Transcity Joint Venture (JV) tunnel fit-out team comprising some of Europe and Australia’s leading tunnel construction specialists drew upon the global strengths of the existing JV member companies and the global reach of leading TBM manufacturer Herrenknecht to develop an innovative system in solving this challenging problem. This globetrotting story, which starts in Australia, visits Europe and mainland China before returning to Brisbane where it all began.CITATION:Brown, T, Strong, S and Sanz Vivanco, L I, 2014. How the global experience and reach of tunnelling’s true multinationals helped solve a road tunnel fit-out challenge, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 507–512 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By K J. Lownie, T Rafferty

The in situ testing of mine ventilation fan systems has been a contentious issue for many years. Site testing was generally undertaken by adapting standards that were developed for the laboratory testing of fans using standardised airways. The deficiencies inherent in this practice have been widely recognised by informed practitioners, and this led to the first stand-alone document specifically intended for the in situ testing of large fans (ISO 5802:2001 Industrial fans - Performance testing in situ).This paper describes the structure of the International Standards organisation and the processes that are followed in the course of preparing such a standard.The application of ISO 5802:2001 is briefly outlined together with how test data is assessed for compliance with the suppliers guarantee. This paper must be read in conjunction with ISO 5801:2007, ISO 5802:2001 and ISO 13348:2007.CITATION:Lownie, K J and Rafferty, T, 2013. A review of ISO 5802:2001 industrial fans - performance testing i n situ, in Proceedings The Australian Mine Ventilation Conference , pp 149-154 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

Blast Engineers frequently use the terminology "the blast showed good heave", or even "the heave was better this time". It is reasonably obvious that "good" and "better" are not the best terms to use. It is also noted that any variation in the data can be misleading. The author proposes a more precisely defined and objective set of measures as tried and tested in a project in 1988. Simple objective measurements of a muck pile profile can measure 1. distance thrown 2. spread of material 3. heaping of material 4. skewness, or bias in the heaping 5. rotation of the mass This technique enables one to compare the profiles from different blasts without relying on subjective experience or judgement. Simple, artificial profiles will be presented to illustrate the problems of description; and then application of the measurement techniques to these profies will be discussed with physical interpretations. The mathematical techniques will be presented, and results of the application of the techniques to real data collected during research carried out at Baimsdale in Victoria, will be presented as illustration. The use of these techniques in mathematical modelling will be discussed.

Jan 1, 1990

By R Lurf, C Weber

In the frame of this paper a holistic dynamic process model approach is presented in order to introduce operational and technical excellence in drilling and blasting. Both on a macro and micro level the single process parts of drilling and blasting are outlined and their interaction is explained. The use of this approach for closing the gap between process planning and process implementation is explained and an example of the value generated is given.

Jan 1, 2007

By P Card

“Let’s get discipline and quality into easy to understand evaluations!” Project Managers and MetPlant Operators accept poor quality evaluations because they are generally unaware of what they should expect.The 2010 draft AusIMM ‘Guidelines for Techno-Economic Evaluations’ were collated by a subcommittee of practitioners and are regarded as best practice.They apply directly to projects and metallurgical plant evaluations, including those with a heavy technical basis. They can be applied to technical problem solving where there are no monetary computations. Project Managers and MetPlant Operators should demand that economic models and evaluations follow the six principles. They should become working tools which are easy to understand, fit for purpose, consistent, rigorous, record sources of input data, have key graphs and are rapid to audit.

Aug 8, 2011

By Setterfield TN, Jones GFP, Tua P, Davis B, Antonio M

The Emperor gold deposit occurs on the western margin of a 5 Ma caldera in a large, mafic shoshonitic shield volcano on the island of Viti Levu, Fiji. Products from two major pulses of post-caldera intermediate volcanism filled the caldera. Caldera collapse-related steep and flat faults and zones of shattered rock provided per- meable conduits for vertical and lateral fluid migration and favourable sites for ore deposition. One large hydrothermal system, operating concurr- ently with extrusion of the second pulse of resurgent volcanism, may have produced porphyry- style alteration within the caldera, epithermal mineralization at Vatukoula, and weakly minera- lized, siliceous veins and breccias in an outflow zone northeast of Vatukoula.

Jan 1, 1987

By A Densten, C Gimber

Surface water management and drainage is a key aspect of mine rehabilitation and closure planning. In the authors’ experience, drainage related problems are amongst the most common forms of failure in mined landscapes. The appropriate design of surface water infrastructure is therefore a key focus of practitioners. While there is currently a trend towards distributed drainage networks and avoiding hard engineered structures, in many situations (especially for existing landforms) engineered drainage structures cannot be avoided. CITATION:Gimber, C and Densten, A, 2018. A risk-based approach to drainage design standard selection for mine rehabilitation and relinquishment, in Proceedings Life-of-Mine 2018, pp 116–118 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By S Hanrahan, S McLaughlin

A case study is presented that details the safety journey at a North American project involving two major contracts: a 1000 m shaft recovery and rehabilitation, and the development of a drainage gallery in a large open pit operation. In the early stages of the contracts, there were a number of incidents that created tension between the owner and contractor, which resulted in the contractor being placed on a final warning with almost imminent potential termination. As a result of this, it was agreed to initiate a focused safety recovery plan as a ‘last chance’.Over a period of two years, the engagement and consequent performance of the contractor was turned around, steadily working to set it up for success such that in one of the contract work areas, a record of ‘one year LTI (lost time injury) free’ was achieved. The journey involved the owner and the contractor teams working cohesively to educate all parties in the safety requirements and, most importantly, providing the context and understanding for certain requirements being put in place. Early on in the process, it was recognised that the owner team unknowingly was an impediment in that they did not fully understand the safety requirements and so was not able to lead the way for the contractor effectively. The journey to rectify the situation was supported and followed up by focused engagement with the project team, which generated a progressive improvement in a very challenging environment.In particular, the contractor turnaround was significant and of enough value for the contractor to ultimately export some of the safety systems from this site to other contract sites. This demonstrated the ultimate benefit of the contractor understanding and buying into a safety culture and system.CITATION:Hanrahan, S and McLaughlin, S, 2016. Winning the safety battle, in Proceedings International Mine Management Conference, pp 181-186 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

The sharp deterioration in Au~tralia'S ternn of trade in recent years and the accumulating national debt highlight the need for a restructuring of the economy which is highly dependent upon primary agricultural and mineral commodity exports (figure 1). Table I gives an indication of the value that can be added to raw material by mineral processing. Significantly higher value is added through downstream manufacturing. In 1987, the mining and rural sectors accounted for 47010 and 38010 respectively of total exports valued at $35,782 million (figure 2). The export contribution from minerals comprised $12,266 mil- lion from unprocessed ores and concentrates and $4,668 million from metals and processed minerals including some simple manufactures. Coal accounted for 450/s of total primary mineral exports. Iron ore and alumina are other important mineral exports, while gold and aluminium are major metal exports. (Figure 3) Australia's minerals are now traded in a much more competi- tive and oversupplied market in contrast to the 1960's and 1970's period which was characterised by increasing exports of largely unprocessed ores and concentrates. Since the early 1980's (I cI) resscd )ver~cas nutrkcts and km rununodlity liriccs ha~c hcen the product of excess capacity installed to satisfy a forecast high growth in demand which never eventuated due to the world reces- sion. During this period the emphasis on technology development was focussed on reducing costs through increased production effi- ciencies in order to maintain competitiveness.

Jan 1, 1988