Search Documents

By Nixon C. A

The exploration of Mount Isa Mines' new copper source will require the development of a five kilometre 4.7 x 5.5 metre blind decline commencing 1000m below the surface and extending to 1600m below the surface. With virgin rock temperatures approaching 60¦C, the ventilation strategy represents a complete departure from any previously used at this mine, in that refrigeration becomes essential. The use of direct water to air cooling techniques has become commonplace in mines throughout the world and their application is being adopted at Mount Isa Mines. A heat load simulation routine has been implemented to allow for the design of refrigeration requirements, as well as to aid in the selection of diesel or electric equipment. This enabled planners to determine the size of a surface based refrigeration plant. Future refrigeration demand for expansion into the ore production stage has also been investigated.

Jan 1, 1988

By Kramadibrata S

Over the years many attempts have been made to develop a means of assessing the excavatability of rock. Most of them are based on an empirical rating system while some authorities still propose the use of seismic velocity as a direct predictor of the rippability of a rock mass. On the other hand there are a number of classical models which have been developed to define the cutting force required at the pick or tooth of continuous miners.While these methods have been applied with various degrees of success to the design of excavation systems there is no generally acceptable method of defining the excavatability or cuttability of a rock mass in terms of the machine power required to generate a particular rate of production.The authors have attempted to overcome this deficiency by recording the intact and rock mass properties at a number of surface mines where continuous miners were in use and to use this data to examine the relationships between the relevant dimensionless groups developed from a dimensional analysis of the problem.The results obtained are encouraging and it appears that this new approach to the problem could lead to civil and mining engineers having a means of predicting the cutting power required to excavate rock at a given rate at any site.While this paper does not include a review of past work it refers to a number of key publications which will give the reader an excellent introduction to the subject.It is important to point out that the research work reported in this paper is part of a doctoral research project at Curtin University of Technology on the Influence of Intact Rock and Rock Mass Properties on the Design of Surface Mines. One of the major objectives of this project is to explore the possibility of developing a technique for predicting the excavatability of rock in surface mines at the design stage.This paper therefore commences with a brief reference to the continuous surface miners in use at the test sites followed by some original work by the authors in applying Dimensional Analysis to analyse the macro-performance of mechanical excavators. Following an analysis of the experimental data the authors validate the wider use of the model by referring to its successful application in predicting the power required to excavate rock by continuous surface miners at other sites.

Jan 1, 1995

By J Kinal

Plant trials are at the best of times difficult to perform; given variations in the ore, operating practice and economic constraints placed on a plant. Testing grinding media at industrial scale adds a further level of complexity that needs to be accounted for.Laboratory test programs consistently demonstrate that altering the grinding chemistry through the application of inert grinding media has the potential to provide significant metallurgical benefit. However, prog- ressing from laboratory testing to industrial trial is often an agonisingly slow process that can lead to inconclusive results which raise more questions than give answers. There are many factors that need to be considered when conducting plant trials aimed at demonstrating the impact of inert grinding media on metallurgical performance. The decisions (or lack thereof) made during the planning stage can heavily impact on whether a statistically meaningful result is achieved. Various factors such as how the trial is conducted (dumping or purging the charge); the circuit configuration; collection of the right data; and even the human factor will affect the outcome. The authors will use examples to demonstrate the importance of proper planning and controlled operation on grinding media plant trials.

Jan 1, 2009

By Wardle L, Wright G

This paper describes the investigations and results of monitoring of deformations of houses located within the area of influence of a pillar collapse over the Westfalen No. 3 coal mine near Ipswich, Queensland. The subsidence resulted in minor subsidence of at least 18 modem houses and serious damage to 4 others. The history of the events and the measures taken to deal with the physical problems arising are described. The investigations and results are described and related to the mining methods and geology. The stability of coal pillars up to 9.6 m high was considered and computer modelling undertaken to relate surface subsidence to estimates of the extent of pillar failure. Assessments were made of the likely extent of subsidence during the incident. Measurements of distortion and tilt were obtained as the ground slowly subsided and criteria established to determine when the structures were deemed to be unsafe. Detailed surveys of houses affected or anticipated to become affected were also undertaken. Four houses were condemned and subsequently demolished as a result of excessive tilt. The methods of assessment are described and the implications of the results related to the various' house designs.

Jan 1, 1992

By J Isles, S King, A Valenza, R Lawolo, J Evert

PT Nusa Halmahera Minerals (PT NHM) is an Indonesian joint venture company owned by a subsidiary of Newcrest Mining Limited (75 per cent) and PT Aneka Tambang (Persero) (25 per cent). PT NHM operates two underground gold mines, Kencana and Toguraci at the Gosowong mine site in North Halmahera District, North Maluku Province, Indonesia.The Toguraci underground mine development commenced in 2011 with ore production commencing in 2012. Water temperatures ranging from 50°C to 80°C were encountered in the Toguraci open pit associated with the structures containing the gold bearing veins and are believed to be fed from a relic volcanic system one to two kilometres below the mine. Underground development and production has continued to intersect these structures with the result that an integrated programme of geological, hydrogeological modelling and operational project work has been required to dewater the mine ahead of the descending stoping fronts.This paper will detail these programmes.CITATION:Lawolo, R, Isles, J, Evert, J, Valenza, A and King, S, 2017. Hot water management at PT Nusa Halmahera Minerals’ Toguraci Mine, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 191–198 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By T Hausler

The pitfalls, pleasures and management issues associated with international and remote projects are diverse.However, no problem is insurmountable and if an engineering team chooses (by luck or good planning) to push through the difficulties, success can mean an extremely satisfying experience for individuals and a significant, positive result for an organisation.International projects are not for the faint hearted or inflexible. Working in foreign lands with people who may or may not speak English and who may not initially respect you can become mentally and physically tiring.Sometimes the challenges are not fully explained to individuals in advance. Individuals then often learn about the challenges ù and discover solutions ù on the job. While this initially puts great pressure on individuals, matters improve eventually, especially when the locals come to understand that you are on site to make a positive difference.This paper will discuss aspects of a recent international project including meeting international clientsÆ expectations, dealing with cultural differences, social reckoning, environmental issues, and personal challenges. Specifically, it will cover aspects of working within a Russian cultural setting and overcoming social barriers.The paper also presents coping strategies for long periods of time spent away from home in remote places with extremes in weather beyond the normal experience of most Australians. For example, dealing with the effects of the spring thaw and coping with temperature ranges of -45 to +45¦C.Lastly, and possibly most importantly, there will be a focus on the role of translators. They have the power to make an engineer everyoneÆs best friend or, on your behalf, to order cold chicken liver and heart salad for lunch. If an engineering team can establish a working relationship with translators, they can become an invaluable asset and both on and off site.CITATION:Hausler, T, 2013. Achieving success in large-scale, remote area metallurgical plant projects, in Proceedings MetPlant 2013 , pp 539-552 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By Rashad MZ

The evaluation of ore deposits consumes much effort, cost and time, hence research work must aim to minimize these inputs with no loss of accuracy. The present study is devoted to assess the optimum conditions and methods of calculations which give minimum costs of ore exploration. An area of (a x a) where "a" is the zone of influence of the semi-variogram, i.e. (2800 x 2800 square metres) located within the Abu Tartur plateau is the subject of the intensive study. The distances between boreholes are varied ie. a/4, a/6, a/8 and a/ 10 respectively. The average ore grade (G), thickness (t) and relative ore reserves (tG) are calculated by four methods. The results indicate that at a distance equal to a/5, the inverse distance squared method gives the best results. These parameters save about 50 percent of the cost of exploration with a map accuracy greater than 90 Percent.

Jan 1, 1987

By Thompson AG, Cadby GW

The New Austrian Tunnelling Method (NATM) is a proven concept for the safe and economic construction of underground facilities. This is especially true for tunnelling activity where changing ground conditions are often encountered. However, the principles central to the NATM have gained only limited use within Australia, presumably due to the measurement process inter- fering with tunnel driving and the cost associated with instrumentation and interpre- tation expertise. The design and operating principles of two basic instruments are explained together with laboratory simulated test results and suggest- ions for use in an integrated NATM style approach to underground excavation and construc- tion. The two instruments monitor load in rock reinforcement and deformation in rock or primary and secondary linings. The instruments may be fitted with a miniature display module which outputs the measured parameter in engineering units directly. The design of the sensing components allows the instruments to be installed in various configurations suitable for routine performance monitoring, quality control, support element testing or detailed investigations. The display module which reduces the need for instrumenta- tion expertise should suit contractors and allow performance data to be obtained which quickly may be used to modify support procedures to suit ground conditions. When complemented by convergence measurements the devices enable most facets of the NATM to be implemented.

Jan 1, 1987

By T Walkemeyer, R Elliott, D Chang-Martin

Over the past decade, discrete element method (DEM) simulations have seen increasing adoption by the resources sector to inform the design of materials handling equipment such as transfer chutes, bins and hoppers. But, if ‘all models are wrong, but some are useful’ (Box, 1979) what approaches are available to check that a DEM simulation is useful? How to avoid garbage in equals garbage out. This work considers what properties of bulk solid flow behaviour are important to transfer chute simulation. Cohesive bulk solids (such as sticky iron ore fines) can develop sufficient strength to form a stable cohesive arch, this phenomenon is not well predicted by measurements of angle of repose. This work presents a two-part approach to the development of a useful DEM model that can be used to add value to the design and optimisation of bulk materials handling equipment. Part 1 is the calibration of not just one, but a range of material models chosen to envelope the range of anticipated materials that will be handled. This work describes the DEM simulation of a batch of direct shear cell tests to develop material models that can be measured by the same metrics routinely used to characterise the flowability of cohesive iron ore fines. Part 2 of this work describes systematic methods for validation of the transfer chute DEM simulations. The DEM model is only useful if it can adequately represent the typical problems observed within a transfer chute, such as blockages due to build-up and cohesive arching. Proper validation requires good observations. Validation examples of site observations are shown side-byside with simulations to demonstrate the adequacy of the DEM model and calibration approach. DEM simulations have the potential to add significant value by allowing engineers and designers to predict material flow-through equipment based on a range of material properties, allowing for stress testing designs and making iterative improvements.

Sep 18, 2023

By F Musa

One of the main energy efficiency opportunities identified from the majority of mine site energy audits is to optimize the comminution circuit to reduce energy consumption through improved throughput and product size distribution. Typical analysis reviews comminution process efficiency/inefficiency i.e. utilization of grinding mills, process bottlenecks and product vs. target size, to identify instances of overgrinding or undergrinding. From this, it is possible to establish the potential improvement that could be gained through formal plant optimization and what the optimization program would entail. It can also sometimes reveal immediate opportunities for process improvement. This paper presents steps that can be taken to optimize the efficiency of comminution circuits.

Aug 8, 2011

The Ok Tedi Project has been planned as a selective mining operation since the Feasibility Study. The nature of the orebody, and the need to 'stage' the infrastructure buildup meant that initially the mill would process gol ore using a leach-CIP process, followed by parallel leaching of gold ore and flotation of copper ore, and finally all flotation of copper ore. Cutoff grades were applied to gold and copper ore of 1.0-1.3 g/t Au and 0.4-0.3% Tot. Cu. Since startup, unpredicted occurrences of sulphide copper and, to a Lesser extent, carbonaceous material, has necessitated significant additional short term drilling (other than at grade boundaries), and shift grade control in the pit to control contaminant levels. Remodelling of the orebody based on the most up to date variography and geological interpretation has had a significant impact on the reserves, and thus the whole project development strategy; necessitating the earlier processing of copper ores, and preflotation of the gold ore.This paper discusses some of these points in detail, and in particular highlights how unforseen geological occurrences coupled with processing restrictions can have significant impacts on ore reserves and the mine development schedule.

Jan 1, 1986

Jarrah Decline is currently the only underground operation at the Boddington Gold Mine, (BGM). The mine is located 120 km SE from Perth in WA, with mineralisation hosted within deeply weathered felsic and intermediate intrusions and volcanic rocks of the Saddleback Greenstone Belt (Morley and McBride,1995). Open cut operations commenced in April 1987 with a mill throughout of 3.OMtpa. A number of upgrades have since taken place, with the oxide material throughput currently milled at a rate of 7Mtpa. In 1992 a separate circuit, the supergene mill, was commissioned to treat copper material from the open cut and now ore from the Jarrah Decline. Current throughput in the supergene plant is 30,000 tonne per month, with a varied blend according to mill requirements. Total gold production from the Jarrah Decline in 1994 was 60,000 ounces from 90,000 tonne of ore.

Jan 1, 1990

By S Tjerry, S Szylkarski, B Willis-Jones, I Dubinski

Achieving relinquishment of mining sites is becoming increasingly difficult, with a study by Byrne (2013) estimating that out of a set of 73 mining and metals sites around the world, less than ten per cent had achieved relinquishment over the last 50 years. The median forecast duration of time allocated for water management in the closure plans studied was approximately ten years, while the reality at the actual sites was a median duration of 22 years to date and growing.One of many challenges in mine closure planning is managing geomorphic stability of stream diversions. The challenge is to be able to demonstrate to regulators and the community that a proposed rehabilitation solution will be stable over the long term.During the mining operations, local watercourses and surface drainage can be diverted and managed using engineered channels and drainage structures. However, during the post-operations stage, the engineered channel and drainage may require modification to a more natural condition that will facilitate long-term environmental sustainability. Achieving geomorphic stability of a diverted watercourse is difficult, with the majority of stream diversions in Australia failing to meet expected design performance (White et al, 2013). Geomorphic stability is a complex process that is controlled by a combination of factors, including hydraulic flow conditions, geotechnical conditions and vegetation.This paper proposes that a fully dynamic and deterministic geomorphological model can be used to supplement the traditional empirical approaches to assess long-term geomorphic stability. The paper provides an overview of the geomorphological models and how they have been applied in engineering studies for forecasting future evolution of stream systems. The paper discusses the potential application of these models in the mining industry for forecasting and optimising surface water structures for the operations and post-operations stages of the mining cycle.CITATION:Szylkarski, S, Willis-Jones, B, Tjerry, S and Dubinski, I, 2016. Improving the reliability of stream diversion designs in mine closure plans using a morphological tool, in Proceedings Life-of-Mine 2016 Conference, pp 212–215 (The Australasian Institute of Mining and Metallurgy: Melbourne)

Jun 28, 2016

The cost of production from truck and loader fleets is influenced by management development of the culture of the organisation, work practices, systems and procedures of the production and maintenance teams. Establishing if the cost of production is the best that can be achieved then requires the measurement of results against established standards of performance. This paper provides a series of discussion points of the factors that influence the cost of production from men and machines for large scale open pit mining operation and provides some suggested performance standards in the form of Benchmarks. Most of the references have been drawn from established large scale deep pit mines in USA, Canada and Australia which have had to implement and constantly fine tune cost efficiencies in order to survive. The discussion provides:ò a review of priorities or the relative importance of the various cost elements for a mining system;ò suggestions of systems and procedures for the operation and maintenance of machines which are considered to yield the best overall results;ò examples of operations that have developed and implemented management systems and controls that are achieving good results in specific functions; andò suggested benchmarks of performance.

Jan 1, 1992

By Khosrowshahi S

The objectives of grade control remain unchanged but new methods are being developed to attain them. Since the early-1990s, an improvement in the power of mine site computers has made the geostatistical tools of conditional simulation more accessible. Optimisation of the grade control process on mine sites now involves two stages: optimisation of the sampling regime and optimisation of the interpretation of ore and waste boundaries. Optimisation of the sampling regime first requires an understanding of the nature of the mineralisation and in particular the impact of particle size on the sampling precision. This relationship, termed the Fundamental Error of sampling, enables an optimum subsampling protocol to be defined for the sample preparation and assaying. However, the actual sample collection method, whether drilling or trenching, must be correctly selected and the sampling grid should be optimised. The relative costs and benefits of various alternative sampling methods and grids can be determined using the method discussed. The use of the grade control data can also be optimised. In the past ore and waste boundaries were often defined using a linear interpolation algorithm that smoothed the data (such as polygonal, sectional, inverse distance squared or even kriging methods). Frequently the relative impact of ore loss and dilution could not be estimated. Conditional simulation to generate equiprobable alternative maps (realisations) can now be adopted to address these issues. A transfer function is then used to evaluate the similarities and differences between the maps. The Ore Block Optimisation (OBO¬) process is a transfer function that produces a three-dimensional model of the optimal ore block outlines. This provides a clear guide for the mining geologist to refine and mine. The nature of the transfer function and the inputs and outputs are discussed. In the past, reconciliation has been the `acid test' for any grade control system. Any ore blocking method based on conditional simulation can make use of the exhaustive data set to ensure that reconciliation between prediction and production will improve significantly. The OBO¬ method provides a guide to the mining geologist to ensure that the best ore blocks are mined. Misclassification between ore and waste is reduced, ore loss and dilution are minimised (and are measurable) and ore is optimally assigned to stockpiles of various cut-off grades. These advantages significantly enhance mine profitability and control of the mined grade.

Jan 1, 1997

By Lawson F

Narrowly sized samples of synthetic chalcocite (Cu2S) and covellite (CuS) were leached in oxygenated acidic sulphate-chloride solutions. Chalcocite leaches via a two-stage process, the first stage being much more rapid than the second. The apparent activation energies are 42.7 kJ/mol and 68.2 kJ/mol respectively, indicating that both stages are controlled by surface chemical reactions. The leaching of covellite is also chemically rate limited with an apparent activation energy of 77.0 kJ/mol. The shrinking core model is able to be used to describe the leaching processes of both copper sulphides. Over 97% of copper present in chalcocite dissolved in 0.5 M H2SO4i0.5 M NaCl solution under one atmosphere pressure of oxygen at 85¦C in three hours from particles 36 pm in diameter while only 85% of the contained copper in covellite particles 13 pm in diameter dissolved in the same solution under the same pressure at 90¦C in six hours. About 99% of the sulphide sulphur in chalcocite was oxidised to elemental sulphur while only 90% of sulphide sulphur was converted to elemental sulphur during covellite leaching. The mechanism proposed for the two-stage leaching of chalcocite particles is as follows: in the first stage, cuprous ions rapidly diffuse to the external reaction surface where they lose electrons and go into solution as a complex cupric chloride ion CuCl'. The second leaching stage begins when covellite is formed at the external surface. Copper again goes into solution as the CuCl* ion. The mechanism for leaching synthetic covellite is similar to the second leaching stage for chalcocite except that the leaching rate of synthetic covellite is substantially lower than that of the newly formed 'covellite'. Elemental sulphur formed on the particle surface retards the dissolution processes during both chalcocite and covellite leaching. The presence of chloride ions is necessary if essentially all of the copper from chalcocite is to go into solution. When no chloride ions were present, the leaching rate of both newly formed and synthetic covellite was almost zero. The main role of chloride ions in both chalcocite and covellite leaching appears to be to disrupt the passivation film of sulphur on the particle surface.

Jan 1, 1989

A review is given of the development of the author's ideas on the relationship of ore occurrence to regional dislocations in the earth's crust, presently identifiable in particular areas as linear discontinuities in patterns of geological and geophysical data. Ideas originating from field observations in Broken Hill were developed in conjunction with three-dimensional kinematic deformation models which were devised to simulate rock structures, and to illustrate their response to assumed linear and planar movements at the scale of mine and regional geology. These led to the study of linear features in the pattern of Broken Hill district geology, and to the observation that the Broken Hill lode occupies a "cross-roads" position at the intersection of regional geological lineaments where they cross through and deflect the host rocks. A genetic association was therefore proposed. The recognition of significant regional lineaments requires special techniques and treatments of field data originally developed for the Broken Hill situation. The subsequent application of the work to the Western Australian shield revealed that known major nickel and gold deposits also occur where the host rocks are crossed by one or more regional lineaments. These lineaments were recognised as part of a continental tectonic pattern of major linear trends with which major ore deposits are associated. The ideas were later used in exploration leading to the discovery of the Olympic Dam deposit at Roxby Downs, South Australia, which is related to regional lineaments.

Jan 1, 1983

By S Casas Castellanos

"Tyres consumption is one of the costliest branches of the operation in a truck-based haulage mine. Off-the-road (OTR) tyres working within undesirable conditions have a considerable negative impact on the whole mine’s productivity. Only the rolling resistance due to underinflated tyres could increase truck fuel consumption by 15 per cent. The impact of other conditions such as road surface quality and temperature are difficult to estimate. Tyre management is a demanding activity that requires a high level of coordination between maintenance and production departments.The project is aimed to develop a smart decision tool to assist mine managers to optimise tyre resources. By identifying factors that have significant impact on tyres, managers are able to take timely action to mitigate undesirable working conditions.The proposed model utilises real-time tyre measurement of pressure, temperature, speed, load, deformation and surface profile to report tyre performance in terms of tonne-kilometre-per-hour (TKPH) and tyre longevity. Both indicators are permanently monitored in order to trigger a warning system designed to keep tyres under optimal working conditions.An interactive database ‘Octo-Mine’ wirelessly receives records from a programmable logic controller (PLC) deployed on the truck. PLC records are the integration of multiple sensor signals with a time stamp. Octo-Mine utilises real-time and historical tyre records to generate online performance and longevity reports, as well as preventative and corrective tyre maintenance scheduling, by comparing current tyre status with established standards.To validate the model, the prototype database was populated with hypothetical data to simulate ideal working conditions subject to comparison with real field observations. Additionally, a laser-based technology prototype device successfully measured a new 9 mm tyre tread and a 60 000 km rolled tyre tread in the laboratory.In conclusion, optimal tyre management contributes not only to reduction of tyre waste but also to truck energy efficiency. This project is a first step in proving these benefits under real field conditions. It suggests that further development of sensor equipment and its integration with a communication system is a worthwhile focus for future research.Citation:Casas Castellanos, S, 2016. Optimum Management of Truck Tyres in a Mine, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 212–228 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

A formalised approach to risk management has been regulated in the United Kingdom (UK) since the Construction (Design and Management) Regulations 1994 (CDM) came into force in 1995. These regulations have recently been revised in 2007. In response to a series of significant claims around the world the UK insurance industry published a code of practice for risk management of tunnels in 2003, and that was followed by an international version in 2006. Probably one of the main contributions of this new approach is the recognition that health and safety risks can best be addressed early in the process, initially by the owner and then by the designers. One of the aims is to achieve elimination of risks by good design. The advantage of a risk-based approach to tunnel design is that all risks are considered explicitly, and any residual risks in the design are communicated clearly to the construction team. This paper looks at the implementation of this formalised approach to risk management with reference to the A3 Hindhead Project. The design has been undertaken in accordance with the requirements of the CDM regulations, and also in compliance with the Joint Code of Practice for Risk Management of Tunnel Works in the UK. An outline of the risk-based design process used is provided, including examples.

Jan 1, 2008

By Mallett CW, Hammond RL

Geological maps of the Pacific Rim recently published by the Circum-Pacific Council for Energy and Mineral Resources have provided a useful perspective from which to view modern plate interaction and the evolution of modern fold belts. An important lesson from any study of modern plate interaction is that of the normality of change. The chaotic is more usual than the simple. Present day convergent margins with mixed characteristics are measures of this chaos. Indeed, the character of less than one third of the present length of the Pacific Rim can be ascribed to conventional models of plate interaction. Another lesson is that of the great mobility of oceanic crust. Enormous areas of the Pacific may not be represented in future fold belts developed at convergent boundaries unless normal consumption processes are disrupted, and even then only by linear zones a few kilometres wide. The axes of divergent boundaries creating Pacific Ocean crust have been equally mobile, with new spreading sites taking over from older sites through time. Divergent boundaries, whether active or inactive, consist of oceanic crust, and may be wholly consumed at collision sites with convergent boundaries. Their only potential contributions to fold belt evolution are transforms and magmatic activity. It is this transform component that can provide us with a mechanism to explain the apparent contradiction of both compressional and extensional features occurring together in a developing fold belt. Reconstructions for the SW Pacific are used to demonstrate that the fold belts under construction during the last 4% (Jurassic- Recent) of geologic time have involved interaction between convergent, divergent, and transform boundaries. In the last 15% of earth history (Late Proterozoic-Recent), many enigmatic features of the geologic landscape in Eastern

Jan 1, 1987