Search Documents

"WELFARE…Welfare endeavor in connection with both the metal and the coal mines of Utah has shown gratifying progress during recent years and both the operators and their employees are deserving of much credit for the efforts put forth to better living, working, educational and receational conditions in most of the mining camps of the state.In the older metal mining camps of Utah, where the towns are incorporated and independent of the mining properties operating in the vicinity, less opportunity is pre¬sented for the companies to exercise efforts looking towards improved welfare conditions than is the case of camps located on company ground and under the full control of operators.Even in such camps, however, as illustrated in Bingham, the companies can do much to better welfare conditions. In this camp the Utah Copper Company has spent $800,000 since 1 920 in the erection of modern brick cottages, apartment houses and the Gemmell Memorial Club. The cottages and apartments have every convenience to be found in up-to-date city homes. The Gemmell Memorial Club, erected and equipped at a cost of $1 75,000, was provided by the company for the benefit of the Utah Copper Company employees living in the canyon and has been made the recreational center for the camp."

Jan 1, 1925

[I-Institute of Metals Division PAUL D. MERICA, Chairman ZAY JEFFRIES, Vice-chairman W. M. CORSE, Secretary General Committee ROBERT J. ANDERSON H. C. JENNISON L. W. SPRING WILLIAN K. FRANK DAVID LEVINGER R. L. SUHL J. R. FREEMAN, JR. PAUL McKINNEY R. F. WOOD]

Jan 1, 1928

By Lane, K. S.

The problem of stability of slopes in reservoirs is one of real interest in civil engineering. The problem is whether the valley walls will remain stable or whether they are likely to slide as conditions are changed by storage of water in the reservoir. If major slides are indicated, as on the walls of relatively steep canyons, one must estimate whether they will be so located and of sufficient size as to interfere with operation of the reservoir-as by blocking the outlets, or by displacing sufficient water to over-top the dam in a huge wave. Some cases involve problems in soil mechanics for slides in earth or weaker rock; other locations need the assistance of rock mechanics for slides in harder rock. While this is not a new problem, attention has recently been focused on its importance by the hugh landslide into the Vaiont reservoir in 1963, which claimed the lives of over 2000 people and forced abandonment of the dam and powerhouse.

Jan 1, 1969

By A. Hultgren

PAGE Outline of Progress of Knowledge and Theories about Gas Evolution in Steel Ingots, and Its Influence on Crystallization and Segregation 2 Object of Present Investigation 16 theoretical Discussion of Process of Solidification 17 Gas Given Off from Rimming Steel during Solidification 17 Equilibrium Diagram of the Iron-carbon-oxygen Alloys 19 Solidification of Pure Iron-carbon-oxygen Alloys 25 Solidification When Carbon Monoxide Is Given Off at Constant Pressure... 25 Solidification When Gas Evolution Is Suppressed 26 Schematic Application on Solidification of Rimming-steel Ingots 27 Influence of Manganese, Sulphur and Phosphorus 28 Experimental Work 30 Liquid Steel and the Mold Gas 30 Ingots Investigated and Methods Used 33 Ingot Structure 42 Structure of Rim Zone 42 Structure of Core 49 Structures Obtained under Special Conditions of Freezing 50 Distribution of Metalloids 55 Other Observations Made 60 General Discussion of Solidification Process 63 Condition of Liquid Steel before Casting 63 Rimming Period 70 Composition of Rim Zone 93 Freezing after Top Is Closed 96 Slag Inclusions and Ingot Scum 102 Reaction between Gas in Blowholes and Surrounding Solid Steel during Cooling 103 Summary 105 Appendix-Preparation and Etching of Ingot Sections 106 References 107 IN 1934, Jernkontoret (The Swedish Ironmasters' Association) appointed a committee for the study of the structure of rimming-steel ingots and the various phenomena associated with their solidification. The members of the committee, including those who have joined it later, have been: I. Bohm, B. D. Enlund, B. Kalling, M. Tigerschiöld, 1. Wohlfahrt and the authors. The present paper? is a somewhat

Jan 1, 1939

By T. H. Oxnam

INTRODUCTION. THE predominating value of the ores now being treated by the Palmarejo and Mexican Gold Fields, Ltd., is silver, although some gold is also carried. The present method of treatment consists of wet-crushing and concentrating, followed by the cyanidation of the unroasted sands and slimes. The sands are treated by leaching and the so-called accumulated slimes by a system of agitation and decantation. It is only within very recent years that the cyanidation of unroasted silver-ores has been commercially successful. In fact, at the time operations were begun at the cyanide-plant at Chinipas, February, 1902, I knew of no other leaching-plant treating similar ores successfully. The cyanide treatment of the Palmarejo ores differs but little from the ordinary practice in cyaniding gold-ores; and perhaps but little, if any, new information concerning the metallurgy of silver is to be gleaned from it. PALMAREJO MINE. The Palmarejo mines are located in the southwestern part of the State of Chihuahua, Mexico, on the foothills of the Sierra Madre mountains, at an elevation of 3,200 feet. The mills, 12. miles distant, are situated on the Chinipas river, near the town of Chinipas, which is about 150 miles northeast of Agiabampo, on the Gulf of California. Supplies are shipped via this port as this route is the best and most direct to the property. The ore-bodies in the Palmarejo mines have been deposited. along a series of rock-fractures, caused by an intrusion of eruptive rock. The most important of these fractures or fissures, both in width and value, are the Prieta and Blanca veins, which.

Jul 1, 1905

By William Paxton Hewitt

Mineral deposits of western Utah and eastern and central Nevada have produced in excess of $8,500,000,000 since 1871. Through 1965, Bingham Canyon had produced over $4,600,000,000 and seven other camps over $100,000,000 each, principally from base metals. In addition, they yield iron and uranium ores; contain the world's largest beryllium reserves; and have produced the United States' most important gold discovery in 25 years. The area is famous for its silver production and its bonanza-type precious metal deposits, but such production has become unimportant. The area's greatest producers of metallic wealth are base-metal deposits in limestones and porphyry-type copper ores. In contrast to silver's decline, gold production has been rising-the result of by-product operations at Bingham Canyon. The area also contains gold deposits in which the gold is so finely disseminated it is not recoverable by panning. The area's gold ores frequently are associated with realgar, cinnabar, and carbon. The ore deposits generally are attributed to Tertiary intrusives,* but, at Mountain City, they may be related to Paleozoic volcanism. Mountain City has yielded rich chalcocite from quartz-pyrite-chalcopyrite bodies in siliceous sediments. Regional stratigraphy and structure are difficult to interpret, 69 per cent of the area being obscured by alluvium or volcanics. In general, central Nevada consists of chert, shale, silty sandstones, lavas, and pyroclastics; eastern Nevada and western Utah of many alternations of limestone, shale, and sandstone. Central Nevada has been structurally active since late Devonian. Although granitic stocks may have intruded eastern Nevada and western Utah prior to the Cretaceous, these areas remained quite stable until affected by the Laramide Revolution. Precambrian exposures, occupying 3 per cent of the area, have not been important hosts. However, the question is raised as to whether Precambrian carbonates, properly situated with respect to invading mineralizers, might yet prove to be important. This paper describes 16 precious metal camps, 6 limestone replacement districts, 2 silver-base metal vein deposits, and 9 miscellaneous types and discusses briefly the 11 * Some ores, as at Ely, are associated with intrusives of. Cretaceous age. major camps that are described in detail in this Volume.

Jan 1, 1968

By David J. Mack

A SURVEY and critical appraisal of published information about Young's modulus was originally made by the writer because of a complete lack of information about this very important quantity in works on mechanics, physical metallurgy, physics, and other sciences. It was felt that a comprehensive summary of such information about Young's modulus might be of general interest and may suggest new problems or lines of attack on other problems that involve E. Hence this paper has been prepared even though it is only a review, with no new ideas or experimental data. The references are only those used in assembling the paper. No attempt was made to compile a complete bibliography on the subject of Young's modulus. CALCULATION OF YOUNG'S MODULUS FROM THEORETICAL OR EMPIRICAL CONSIDERATIONS Many attempts have been made to compute E from theoretical considerations. The earliest calculations were probably those of Tomlenson (1883) and Southerland (1891), but Fessenden 41,42 made extensive calculations a few years later and arrived at the relationship: [2E = 78. 101 (_L V] where V is the atomic volume. In 1923, Peczalski,43 working from the same stand-point but with more information available on atomic structure, arrived at an identical relationship, which he expressed as: [E=B(m) 2] where B is a constant of value about 8 • 10 7, p is density and m is atomic weight; the atomic volume, of course, being m/p. Portevin44 immediately pointed out that while the equations of Fessenden and Peczalski were true of the common metals, they gave low values for the refractory metals with high moduli (Fig. I). He showed (Fig. 2) that much better concordance was obtained by means of an empirical equation of the form: [E _ KT'Vb] where K is a constant; T the absolute melting point; V, atomic volume, and a and b constants of value approximately I and 2 respectively. This constant K in the Portevin equation is not necessarily the same for all elements, as shown by Thompson.45 Other equations for E based upon theoretical considerations have been derived by Honda and Yamada49 and Lasareff. 50 The most recent calculations of elastic moduli based upon quantum mechanics are probably those of Fuchs.46-48 He extended the method of Wigner and Seitz for calculating the lattice energy and compressibility of monovalent metals and computed the elastic constants of lithium,

Jan 1, 1945

By Linney, Robert J.

REPUBLIC Steel Corporation's iron-ore properties in the Adirondacks consist of mines, mills, and sintering plants in the Mineville and Port Henry area and at Lyon Mountain. This article will deal with the properties in the vicinity of Mineville and Port Henry. In 1938, when Republic leased the Mineville- Port Henry operations from the Witherbee Sherman Corp., these properties had just come through some hard depression years. As a result, the mine development program was far behind schedule; most of the equipment needed replacement; and above all, the entire system of mining had to be completely changed to reduce operating costs. The concentrator had been in operation for many years; the process was dry and dusty. Machinery and equipment were either badly worn or entirely obsolete. The sintering plant, also long in operation, was badly in need of repairs.

Jan 1, 1943

By Cadwallader Evans

MY endeavor in this paper will be to tell something of the accomplishments and current problems of the anthracite producer and to suggest some of the avenues for technical development that seem to me to be the most necessary and likely to bear fruitful results. The several subjects, that I find of most interest will be taken up individually with brief reference to the future trend. Underground Mining and Loading ?In this field great progress has been made in the last twenty years, beginning with the introduction of the scraper system. The electrical hoists for the operation of scrapers have been improved, and give little trouble, but there is an open field for the improvement of the auxiliary apparatus, particularly in the application of roller-hearing sheaves to the guiding of scraper ropes. Also notable in the last six or seven years is the introduction of shaker chutes, so that far more anthracite is now loaded over them than by scrapers. This trend should continue to be manifest, particularly if those who are looking ahead and who are charged with the development of this specialty continue constantly to study and improve the mechanical design of their shakers.

Jan 1, 1938

By L. W. Legerwood

During the past three decades, the oil industry has expended increasing eflorts seeking improved drilling tools or systems to reduce drilling costs. The total cost of these efforts is unknown, but it certainly amounts 10 tens of millions of dollars. Most of the "new" system that past and present investigators have sought to develop actually are old public information. In seeking to implement new-systern concepts, investigators have tested the following: impact at frequencies ranging from 6 to 300 cycles per second; electrical, mechanical and hydraulic meam of actuating percussors; bit rotary speeds up to 2,000 rpm; electric and hydraulic bottom-hole means of rotating bits; bottom-hole machines with power outputs up to 400 hp; shock waves; explosives; high-velocity pellets; flame; arc; grinding wheels; abrasive jets; erosion by high-velocity gases; chemical attack; electric current; magnetic waves; retractable rock bits; reelable drill pipe; continuous coring with reverse circulation; and automation of drilling rigs. Table I shows how these investigations are grouped for discussion purposes in this paper. In spite of these efforts to discover new and improved systems, rotary drilling main;aim its economic leadership. Undoubtedly, rotary drilling costs will continue to be reduced by rigid application of the best available technology and by development of new rotary technology. In view of the extensive past development programs, however, significant long-range improvement appears to be a research, not a development problem. Research must postulate and prove theories and principles governing variour subsurface rock-failure processes pertinent to both rotary and new systems. Ah, research must produce physical and engineering data relative to these processes. When such information is available, earth boring will graduate from an art to a science. Major improvements in rotary drilling can then be expected, and the systematic evolution of an improved drilling method can be initiated—with a strong probability for success. Development of drilling methods other than rotary drilling has been one approach investigated by the industry as a means for reducing drilling costs. Major cost-reduction efforts, however, have been centered on engineering development work aimed at incremental improvements in rotary drilling. A relatively minor effort has been expended to establish basic physical principles and engineering data pertaining to the earth-boring process which can serve as a foundation for the development of cost-cutting drilling hardware. Current oil-industry economic trends have added impetus to the need for effective programs to reduce drilling costs. However, areas for expanded future efforts should be selected only after careful study of past investigations. It is the purpose of this paper to review past and Dresent industry efforts to develop new drilling tools or systems and to suggest areas where additional science is needed. Past reviews of drilling methods have been limited to a few processes prominent at the time the reviews were made. This paper seeks to present a concise, well organized review of all methods that have received actual development or test work. The preparation of a paper seeking to review all past developments is fraught with many difficulties, not the least of which are errors in or obsolesence of printed matter used as source material and the lack of data on industry developments which have not been published. Since de-

By Elwin L. Fisk

The Cordero mine is located in the Nevada portion of the Opalite Mining district that straddles the Oregon-Nevada state boundary. The mercury deposits of the district occur along the margins of the broad east-west graben valley of McDermitt Creek. The only other major producers, the Opalite and Bretz mines, on the northern margin of the graben have thus far exploited only shallow deposits within 100 feet of the surface. Through December 1965, Cordero has produced 94,680 flasks of mercury, the most of which came from the large underground cinnabar deposit. Nearly all of the mercury ore deposits in this district have been found in Miocene rhyolitic intrusives, flows, tuffs, and lake beds. These rhyolites have been argillically altered at depth and extensively silicified at or near the surface. These silicified areas or "opalite" masses were the original cinnabar-bearing outcrops.

Jan 1, 1968

[†AARONSON, ALFRED E., Vice-Pres., Mid-Co. Petroleum Co., Mid-Co. Bldg., Tulsa Okla. '18 ABADIE, EMILE R., Min. Engr Box 927, Porterville, Cal. '76 ¦ABADILLA, QUIRICO A. Student, Colorado School Of Mines, Golden, Colo. '20 ABBOTT, CLARENCE E., Gen'l Supt. Iron Mines Div., Tenn. Coal, Iron & R. I. Co., 1405 Minnesota Ave., Bessemer, Ala. '04] [ ]

Jan 1, 1925

By Wallace W. Wilson

This DaoerAA calls to attention for the first time, to the writer's knowledge, a purported recovery of oil by substantially horizontal gas cycling that is considerably in excess of 50 per cent of the oil originally in place. The average angle of dip along the path of travel of the gas is less than one degree of arc. The best recovery by gas cycling previously brought to the writer's attention1 occurred in the case of the Mile Six Field in Peru, where about 68 per cent of the original oil in place has so far been recovered. In this case, however. the recovery was greatly aided 1)y the high dip angle of about 17.5". An approximate estimate of recovery was made by the method developed by the writer' for the case of the Cook Ranch Field, using an average relative permeability ratio function dictated by past experience with a number of good quality sandstones. A result of about 40 per cent recovery of the original oil in place wa* obtained after the 8.5 pore volumes of cumulative gas cycling undergone by the Cook Ranch Field. Tile writer desires to emphasize what appears to him as the sound engineering practiced at Cook Ranch, and also the care attending the taking of data and the high quality of the calculations made. It is impossible to take issue on factual grounds with any of the conclusions drawn in the paper. It is, however, desired to point out the difficulty of explaining the unexpectedly favorable oil recovery on ordinary theoretical grounds. It would be of interest to know whether relative permeability ratios have been measured on the Cook sand. The operator is inclined to attribute some of the excess benefit to settling of the oil across the bedding planes into the lower part of the sand. It is difficult for the writer to appreciate the importance of such an effect, inasmuch as the concomitant opening of excessive vacated pore space in the upper part of the sand would he expected to cause excessive bypassing of the gas. REFERENCE 1. Welge. H. J.: "A Simplified Method for Computing Oil Recovery by (Gas or Water Drive." Trans. AIME, (1952), 195, 91. AUTHOR'S REPLY TO MR. WELGE Welge has poined out clearly the difficulty of applying material-balance procedures in calculating the Performance of low-pressure, dispersed gas injection operations. There can be no argument that even with the most favorable assumptions of K,/K,, and with cumulative gas cycling in excess of normal expectations, the calculated oil recovery will be considerably less than the 72.5 per cent recovery realized from this project to Jan. 1, 1951. There probably are at least two reasons for the unusually high recovery from this reservoir, the effects of which would be difficult or impossible to calculate by known methods: 1. The operator did not use the same injection wells for the entire operation, and exercised considerable control over producing GOR by changing the locations of injection wells whenever well performance indicated excessive bypassing. Fifty-six wells were used for injection, not over 29 of which were in use simultaneously. This procedure resulted in frequent shifting of the fluid movement patterns in the reservoir and undoubtedly increased the ultimate recovery. The writer knows of no satisfactory procedure for calculating the effect of this practice. 2. Vertical movement of oil across the bedding planes of the reservoir rock hy gravity drainage tended to maintain a relatively high oil saturation, and hence a favorable K,/K, ratio, in the lower sections of the reservoir. As pointed out by Welge, this condition has aggravated the tendency for high producing GOR, but at the same time it has resulted in increased oil recovery. As may be seen from the performance charts for the various battery areas, operating (GOR'S have been quite high for the last several years of reported history.

Jan 1, 1952

By D. S. Choi, R. Stefanko

There are a number of complex factors that influence the effectiveness of anchorage to maintain tension in rock bolts. However, a plastic analysis of the anchorage site employing certain simplifying assumptions with application of the Mohr-Coulomb criterion appears to explain the observed phenomena. Such an analysis has been made and a correlation sought with field and laboratory tests. Field tests were made in an anthracite mine in eastern Pennsylvania and included pull tests and long-term tests of a variety of anchorage devices in two basic lengths, 30 and 42 in. in two widely differing seams. Performance is reviewed for wedge, expansion shell, and resin anchorage. Laboratory tests duplicated many of the field conditions but in addition compared the performance of shells with normal and reversed serrations. This performance was compared with the predicted results from the plastic analysis. One of the major problems in conducting long-term underground tests is the selection of suitable instrumentation. All installed bolts were fitted with spherical and hardened washers to insure the best possible torque wrench readings. In addition, commercially available load cells were used. Finally, the performance of a specially developed strain-gage-equipped ring cell is viewed. Rock bolting as a method of support continues to increase with applications in many other industries in addition to mining. Nevertheless, with nearly 55,000,000 roof bolts installed in coal mines alone last year, this remains as the single greatest use. While bolts have frequently supported ground where conventional timbering could not, there are relatively few design criteria; and trial-and-error procedures prevail. Furthermore, there has been a lag in development of suitable instrumentation that is simple to install and read out, sensitive, durable, reliable, safe, and economical in evaluating the effectiveness of a bolt over long periods of time. Therefore, the pull test continues to be the most popular method of evaluating the applicability of a certain type of roof bolt under specific installation conditions. At The Pennsylvania State University in the Dept. of Mining, research has been conducted for a number of years to measure bleed off in carefully controlled laboratory experiments as well as in underground investigations."-' Unfortunately, most of the instrumentation developed has been primarily suitable only for research purposes, not possessing all of the aforementioned characteristics desirable for routine underground use. Other groups also have met with restricted success. Therefore, while relatively crude, the torque wrench continues to remain as the most widely used load measuring device. While both field and laboratory tests continue to be con- ducted, analytical analyses are attempted to discover the more important design parameters in order that more efficient anchorage might be devised. Bolts are being used for a greater variety of purposes in mining. Suspending wire sideframe belt conveyors from roof bolts is a common application. The suspension of a monorail transportation system presents yet another. One such system has just been installed in a recently reopened anthracite mine and is presently being evaluated under production conditions. Preliminary studies revealed that a considerable cost reduction was possible by suspending the monorail on bolts anchored in the top. The monorail was to be installed under two widely differing conditions—a competent sandstone above the Buck Mountain seam and a softer shale top above the Skidmore. The type of anchorage device, length of bolt, and long-term performance, consistent with economy and safety, had to be established for the installation once the decision was made to suspend the system on rock bolts. This paper describes some of the testing procedures leading to a final selection. Theoretical Analysis of Expansion Shell Anchorage A detailed look at an expansion shell assembly might shed some light on the factors involved in the design of a suitable shell, Fig. 1. When a bolt is rotated, the tapered plug is forced downward, expanding the leaves laterally to grip the sides of the hole. Two friction surfaces are present: (1) the interface of the plug and leaf and (2) the interface between leaf and rock. The relationships of these friction planes, geometry of expansion shell, and properties of the rock are important in the design of an expansion shell. Therefore, an analysis assuming the rock to behave as a rigid plastic material with its yield governed by the Mohr-Coulomb criterion was made." Furthermore, the effect of friction between the leaf and rock produced by serrations was analyzed.

Jan 1, 1971

By Thomas T., Read

THE decades immediately before and after the end of the nineteenth century (1890-1910) were a period of increased activity in mineral industry education. One reason for ,this, undoubtedly, was the rapid increase in mineral production in the decade 1880-1890; pig iron and copper production tripled; coal, lead, and zinc output more than doubled. Most of the other mineral substances followed the same general trend. Aluminum production began in 1886; petroleum output, which in 1888 was less than it was in 1882, almost doubled in the next three years. Gold alone showed no appreciable change until its discovery at Cripple Creek in 1891, followed by the Klondike in 1896, brought to boiling a public interest in minerals that had been simmering for some years previously. The first cyanide plant in the United States was erected at Bodie in 1893, and the first chlorination plant at Cripple Creek* the next year. Silver- lead smelting had already greatly developed, and the metallurgy of copper was almost transformed. The hearth area and smelting capacity of copper reverberatory furnaces more than quadrupled between 1878 and 1894; matte converters were first erected at Butte in 1884. Copper production of the United States in 1899 was 30 times that of 1872. While it was the increased technology used in mineral production that really made the field attractive for educated young men, undoubtedly they did not realize that, and were impressed mainly by the quantitative increase in output. Another factor was the increased general interest in engineering education; three times as many men took engineering degrees in the United States in 1890 as in 1880; 1893 showed almost a 56 per cent increase over 1890. Industry had come to recognize that technical training was worth while. The mineral industry lagged somewhat at first; the total number of mining degrees

Jan 1, 1941

By Best W. N.

Discussion of the paper of W. N. BEST, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 104, August, 1915, pp. 1527 to 1537. WILLIAM A. WILLIAMS, San Francisco, Cal.-I would like to ask whether .Mr. Best ever had any experience with an oil burner that used neither air nor steam? W. N. BEST, New York, N. Y.-Yes. This type is commonly known as the "mechanical spray burner" and uses oil heated under high pressure to above its vaporizing point. These burners are not as efficient as the atomizing type for the following reasons: 1. They produce a round flame which; as with any other type of burner, must pass over a flat surface. A round flame cannot fit a flat surface. 2. They do not evenly distribute the heat, resulting in localized heat. 3. The outlet through which the fuel passes is very small; so all gravities of oil, especially oil containing sand, cannot be burned. 4. Their construction is such that they must be cleaned frequently, as the residuum in the fuel clogs the burner. 5. The oil opening being small, the capacity of each burner is small, so that many burners must be used in a boiler or furnace. (The fewer burners there are, the more accurately they can be regulated.) In marine boilers, these burners are largely used, because they do not require either steam or air for atomization. However, there are other methods by which this objection to other types can be eliminated, such as by the use of a rotary blower and steam turbine engine, the exhaust front the engine passing into the engine condenser, thus obviating loss of water. Mechanical burners are rarely used in shops. I know of but one power plant using them. With mechanical burners, the fuel must be maintained at a high pressure. On board naval vessels, some mechanical burners demand an oil pressure of from 100 to 6001b. It is advisable to reduce the pressure as much as possible, as fractured pipes or fittings are particularly dangerous, for the heated oil escapes as a vapor. In such cases there is liability of an explosion caused by spontaneous combustion.

Jan 12, 1915

By J. D. Doherty

That America's great coal deposits eventually will be our principal source of liquid as well as solid fuels is generally accepted. Moreover, the day when synthetic oil from coal will begin to supplement our petroleum supplies does not appear to be far off. The American petroleum industry has not spared effort or expenditure in its attempt to keep pace with the demand for oil, and recent production has exceeded expectations. However, the rapidly rising demand for liquid fuels plus the increasing difficulty of finding and developing the new oil needed even to maintain present production rates make it highly unlikely that oil from domestic wells can fully meet future oil requirements. Therefore, it appears that one or more of the following courses must be followed: 1. Curtail oil consumption. 2. Increase imports. 3. Develop new sources such as synthetic liquid fuels.

Jan 1, 1949

By D. C. Lindley, D. H. Gaucher

The displacement of oil by water in a waterflood project is accomplished by the action of transient viscous, gravitational and capillary forces which drive fluid through interconnecting pore spaces toward production wells. The relative importance of each of these forces to the effectiveness of the displacement and the production history depends on properties of the reservoir itself and the manner in which it is operated. There has been considerable discussion'-3 concerning the importance of these factors and the extent to which they control the performance of individual waterflood projects. No data have been presented, however, to demonstrate the effect on waterflood behavior of variations in rock permeability, water-injection rates and mobility ratios in three-dimensional reservoir systems in which viscous, gravitational and capillary forces are allowed to assume the proper relative influence on fluid flow. Much information relevant to water flooding has been gained from the study of field case histories. But, the complexity of the systems involved, the difficulty of defining geometry and obtaining sufficient data, and the fact that the same reservoir is never flooded twice with the same initial conditions, all obscure the role of process variables such as rate. Further, mathematical calculations of waterflood behavior are restricted at this time by available mathematical techniques to highly simplified situations. Scaled models, however, do offer an approach at the present time to evaluation of the effects of the pertinent variables. Several investigators have predicted prototype reservoir behavior from observations of model waterflood performance under a variety of conditions. Two-dimensional aspects of waterflood pattern efficiency have been investigated by Muskat, Aronofsky, Dyes, et al, raig, et al,' and Rapoport, et al. he effects of gravity segregation, viscous fingering and permeability stratification have also been studied in two-dimensional models. Craig, et al," studied the importance of gravitational forces on frontal displacement in three-dimensional models with wells on a five-spot pattern. This work in- vestigates the tendency for water to segregate in homogeneous reservoirs because of gravity and to under-run the oil for a range of water-inject ion rates. The effects of permeability stratifications were investigated by these authors using miscible fluids to simulate water-channeling through permeable strata in systems of negligible capillary force. In this investigation, a three-dimensional model of a five-spot pattern flood was designed to represent typical prototype conditions, and the sand and liquid properties were selected so that capillary, gravitational and viscous pressure gradients were scaled. It was not, however, possible to achieve exact similitude regarding viscous fingering when the more viscous oil was used. The effects of rock stratification on waterflood behavior were studied by changing both the permeability ratio and the position of the more permeable sand stratum in a two-layered, horizontal model. For each type of stratification, constant-rate floods were performed and the rates were varied, in separate experiments, over a tenfold range. To observe the effect of mobility ratio on flood performance, two series of constant-injection-rate floods were performed on the most highly stratified reservoir at a water-oil viscosity ratio of one.

[NOTE.-The names of authors of papers are printed in small capitals, and the titles of papers, in italics. Casual notices, giving but little information, are indicated by bracketed page numbers. Large Roman numerals are volume numbers; small Roman numerals after volume numbers following titles indicate the page on which the presentation of the paper is mentioned; Arabic figures refer to the text of the printed papers.] A Use Classification of Coal, (ASHLEY) LXII [xiv]; LXIII, 782; Discussion: (HALL), 794; (ZERN) , 795; (ASHLEY), 795 Absorbent material, liquid-oxygen explosives, LXXI, 1251. Absorbents for liquid-oxygen explosives, LXIX, 292, 299. Absorption : cupellation : gold, special cupels, LIX, 194. primary and secondary, LIX, 213. ratio of silver to gold, LIX, 212. silver, specla1 cupels, LIX, 195. Absorption method, gasoline from natural gas, LIX, 584, 585. Absorptzon of Sulfur from Producer Gas zn Open-hearth Furnaces (NEAD), LXX, 176; Discussion: ( WATERHOUSE), 184 ; (REYNDERS) , 184; (KINNEY), 184 Accelerated wearing tests, bearing metals, LXIX, 973. Accident prevention, results, Utah, LXVIII, 360 Accident Prevention, 1919 (SINN), LXIII, [xiii] Accidents: causes in coal mines, LXXI, 1229. classification, Anaconda Copper Mining Co., LXVIII, 9. coal mining: comparison with metal mining, LXVIII, 360. pillar mining, LXVIII, 323. relation to method, LXVIII, 323 shafts, LXVIII, 207, 209 Utah, LXVIII, 363 - concentrating mills, Utah, LXVIII, 362 liquid-oxygen explosives, LXIX, 330, 339 losses through, LVIII, 65 metal mining, LXVIII, 361, 363. mine: causes, LIX, 652. curve of decrease, LIX, 655 days of greatest frequency, LIX, 657 human element as cause, LIX, 652, 653. intemperance as cause, LIX, 658 labor relation, LIX, 652 prevention, LIX, 653. record, New Jersey Zinc Co., Franklin mine, LIX, 655 time of greatest frequency, LIX, 657, 658 Utah, LXVIII, 360 prevention, LVIII, 65 report blanks, Anaconda Copper Mining Co, LXVIII, 13, 15. statistical base, Anaconda Copper Mining Co, LXVIII, 9 time lost, LVIII, 70 transportation, Clifton-Morenci district, LXX, 851.

Jan 1, 1926

By Roger L. Beals, George A. Tweedy

I. INTRODUCTION. THE results of the cyanide-operations, given in detail in the following paper, show the progress that is being made at the Minas del Tajo. The old pan-amalgamation process, in operation up to and including 1905, while paying a profit on high-grade ores, was no longer able to treat profitably the ores in sight at that time, hence an alteration in the process was imperative. The success of this alteration is eloquently expressed by the following data Pan- Amalgamation. Cyanidation. 1905. 1907. 1903. Tons treated, . . 51,387 53,983 69,300 Value per ton (U. S. currency),. $10.75 $8.39 $8.28 Extraction, per cent., 65.00 88.50 S7.45 Extraction, per ton. .- $7.00 $7.4.; $7.24 Total cost, per ton treated, 6.50 4.311 4.01 Profit, per ton treated, . . 0.50 3.07 3.23.;

Feb 1, 1910