Search Documents

By Alfred F. Beasley

The slags derived from the smelting of lead and copper ores are composed essentially of silicates. The problems arising from the smelting of these ores consequently involve the study of silicate fusions. In the absence of specific knowledge concerning the compounds occurring in slags, it has been the practice of metallurgists to treat them in terms of their total chemical composition. Slags have been classified as monosilicates, bisilicates, sesquisilicates, and subsilicates according to the relative amounts of oxygen in the acid and basic radicles of the hypothetical salt produced. While this has been a useful guide to metallurgists in computing the furnace charges, it falls far short of a basis for the scientific investigation of slags. In order to understand the nature of a slag as a whole it is necessary to learn the physical and chemical properties of the mineral compounds which go to make up that slag. The efficiency with which an ore is smelted in a furnace depends primarily on the physical properties of the compounds formed during the operation. When the melting points and fields of stability of each of the mineral compounds in slags have been established, it will be possible to determine the properties of any given slag by examining the nature and amounts of its mineral constituents. Earlier Investigations In 1884 and succeeding years an extensive survey of lead and copper furnace slags was made in Europe by Vogt, and a large part of the present knowledge of the subject is due to his publications.' Vogt's interest in artificial fusions was directed primarily towards the explanation of problems in igneous and economic geology and his subsequent works have been confined wholly to that subject.

Jan 1, 1930

By Robert Goodwin, Frank R. Milliken

IN September 1939, the Ohio Copper Co. inaugurated the treatment of its copper-bearing mill tailings at Lark, Utah. These tailings had been accumulated during the regular operation of the Ohio Copper mine and mill over the period 1907 to 1919. Gravity concentration had been employed except for a comparatively short period in 1919, when flotation was used. The ore milled during that period assayed about 1 per cent Cu. The chief copper mineral, chalcocite, was disseminated in a shattered quartzite, mainly along fracture or cleavage planes. The quartzite gangue was extremely hard and grinding to liberation resulted in excessive sliming of the "sooty" chalcocite, with consequent high tailings losses. Recovery on the seven million tons treated was probably less than 6o per cent of the total copper content. As early as 1918, attempts had been made to sample the dump. In 1928, a complete sampling program was undertaken. The sampling consisted of seventy-four 5-in. post auger holes drilled to the full depth of the dump at regular intervals of 250 ft. Each 10-ft. portion thereof comprised a sample for analysis. Each sample was screened, rolled, divided into three parts, dried and assayed. The reject was retained for testing purposes. From the depth of the auger holes a contour map of the dump was plotted, Fig.1, which gives percentages of tonnage and copper content. The tonnage within the limit of the drill holes was estimated at about five million tons with an average content of 0.42 per cent Cu, 31 per cent of which (0.13 per cent) was acid-soluble. A screen analysis of the composite dump sample is shown in Table I. Flotation tests by several companies and individuals were then made, the results of [ ] which ranged from 62 to 74 per cent recovery. On the basis of these, a Zoo-ton pilot plant employing straight flotation was built and operated for a few months. Operation of this plant was unsuccessful, as no provision had been made to handle the copper-bearing solutions resulting from the water-soluble copper, a point that was overlooked in the laboratory test work. Attempts to decant the copper-bearing solution for precipitation in the usual manner ahead of flotation were not satisfactory because of low water recovery (owing to poor settling characteristics of the pulp) and contamination of the copper precipitate with unsettled slime. Low copper prices in 1931 necessitated the termination of testing. With the stimulus of higher copper prices in 1937, a review was made of metallurgical

Jan 1, 1940

By Herbert Johnson

DURING the past 10 or 12 years very little information has been made generally available concerning the commercial possibilities of separating materials by means of static electricity; and yet during that same period important improvements have been made in various branches of the science of electricity, which, when taken together, and applied to electro-static separation, have resulted in important improvements in that art as well. For example, much improvement has been made in high-voltage electrical equipment such as full-wave vacuum-tube rectification and improved mechanical rectification. Great strides have likewise been made in the development of insulators for high-voltage work, not only in the materials used but also in the design of the insulators themselves. Again, in another field, the development of air-conditioning equipment has improved the technique of controlling the surface condition, through drying or humidifying, of the various materials that are passed through the electrostatic separator. In many authoritative publications and textbooks, the electrostatic separation process is declared to require a balance far too sensitive for general commercial application. For example, one publication1 in the past has referred to an unfavorable effect on the process caused by varying atmospheric conditions such as humidity. Some2 have even gone so far as to state that sunlight and shadows may seriously affect the separating efficiency of the process. Such statements may have been true in the early development of the art, when the source of static elec-tricity was derived from a friction disk machine, such as the Wimshurst. The Blake Mosher equipment and the work of Huff in applying motor-generator sets, transformers and mechanical rectification overcame much of this kind of objection to the commercial application of the elec-trostatic separating process.

Jan 1, 1938

NEW MEMBERS The following list comprises the names of those persons who became. members during the period Sept. 10, 1918, to Oct. 10, 1918. ADDISON, HERBERT, Vice-pres. and Mgr., Big Horn Collieries Co., 412 Colorado Bldg., Denver, Colo. ALLAN, .ANDREW, JR A. Allan & Son, Harrison, N. J. AMI, HENRY M., Charge of War Metals and Minerals, British Embassy, Washington, D. C. ALTHAR, HOMER C., Mill. Engr., The Lorain Coal & Dock Co., Bridgeport, Belmont Co., Ohio. BASER, JOHN T Pres., J. T. Baker Chemical Co., Phillipsburg, N. J. BARBA, W. P., Lieut. Colonel, Ordnance, U. S. A., 2301 Connecticut Ave., Washington, D. C. BENSON, JOHN PATS Min. Engr., Aurora Cons. Mines Co., Aurora, Nev., BOSWELL, H. F Resident Inspector, Southern Railway System, St. Louis, Mo. BRAUCHER, PETERS., Foundry Mgr., Philadelphia & Reading Ry. Co., Sixth & Perry St., Reading, Pa.

Jan 11, 1918

By H. D. Strain

Potash is a generic term used to describe a number of compounds containing the element potassium (K), which is one of the three major plant nutrients. Potash content of these compounds is commonly expressed as percentage potassium oxide (K20), and the market value of the products is usually dependent on contained K20. Most of the potash produced (approximately 95%) is used in agriculture as fertilizer. Potash products today are shipped by producing countries all over the world to meet the need for increased food production. WORLD POTASH RESERVES Apparent world potash reserves are shown in Table 15.2B.1 and total some 96 billion mt of recoverable potassium oxide. The Canadian reserves account for approximately one-half the known world reserves. The reserves shown represent the potassium oxide content of a variety of potash-bearing ores. The major ore is sylvinite (a mechanical mixture of KC1 and NaCl) from which KC1 or sylvite is recovered (63.2% K20 equivalent). Other ores, such as langbeinite (potassium, magnesium sulfate-22.7% K20) and carnallite (potassuim magnesuim chloride-17.0% K20) are also mined in various parts of the world, mainly for the potassium content. Theoretically, potassium is available in almost unlimited qualities from brines and saline waters. To date, the cost of recovery from salt brines has been greater than the costs by mining operations, but new technology could make brines and seawater an increasingly important source. POTASH PRODUCTION Potash production dates back to the 1860s in Germany, which was the only recorded producing country until 1912. By 1912 Germany was producing approximately 1 million tpy of K2O equivalent. Production began in France in 1913 and in the United States in 1915. World potash production and consumption are shown in Table 15.2B.2 for the years 1950-51 through 1967-68. In 1967 and 1968 the major potash-pro¬ducing countries in order of importance were those listed in Table 15.2B.3. By 1972 Canadian production had outstripped U.S. production. WORLD CONSUMPTION World consumption of potash for the years 1950-51 through 1967-68 is shown in Table 15.2B.2. Table 15.2B.4 shows total world consumption of potassium materials in 1967-68 by country. More than 70% of the world's potash is

Jan 1, 1976

By William B. Potter

It is a time-honored custom in this, as in other kindred bodies, for the retiring President on giving place to his successor, after a year of official duties which have been the means of directing his attention in a more than usual degree to the work and interests of the Association, to report the results of his observations from this outlook, and the thoughts that may be suggested by the view. In looking out over the many fields of activity within the range of this Institute, the attention may be arrested by special features marking recent progress and development, or such as by their meager outline or lack of important detail stand in less pleasing contrast, or. even form unsightly objects in the view. It may be that the special field and particular work in which one is engaged will, when observed from the more distant standpoint, or in the light of the whole outlook of the profession, assume a different aspect or develop features of new interest and importance. In this way some special object may suggest to the observer a, fitting theme for the occasion. To others, again, an outline of the whole view may seem a more useful subject for study and review. All fields are examined and the wide horizon of the whole profession scanned to note and report whatever is new in knowledge and practice—the new permanent bench-marks that appear near the horizon designating ground definitely located; the stakes which mark reconnoissance into new territory, and even the prominent objects that faintly appear through the mist of the distant atmosphere, and which may serve later on as points of attachment for the advancing lines of survey into the unknown. And besides these, there is the progress of the work in older and nearer fields—what has been attempted, what accomplished,

Jan 1, 1889

By Ingvar Janelid

DURING the last ten years, in the effort to save manpower and costs, methods of drilling and blasting in Sweden have changed and developed in a revolutionary manner. These developments have been accompanied by extensive alterations in methods of tunneling and in mining technique. Since the end of the 1940's there has been a 100 pct change-over in Sweden to the use of tungsten carbide tipped drill steel. Both investigations and practical results have shown clearly that a tungsten carbide chisel bit fastened directly on the drill steel is the most economical for Swedish conditions. This applies to drill steel up to the longest size it is practical to handle. In terms of drilling footage, durability of the drill steel and the tungsten carbide bit is generally the same. In this respect, therefore, a detachable bit offers no advantage over integral steel. Transportation of integral steel to the grinding plant, instead of detachable bits only, involves heavier work, but this is counteracted by placing grinding plants closer together or by grinding at the working place itself. The drilling rate with integral steel is higher, the trouble of changing bits is avoided, and the difficulties which always arise with joints are eliminated.

Jan 6, 1954

By David P. Hale, Guy W. Jordan

High-iRon cements have a number of advantages over cements carrying little or no iron. The presence of iron in Portland cement aids in the manufacture of the cement and also imparts certain advantageous physical properties to the finished product. In manufacture, the presence of iron lowers the fuel consumption, increases the ease of proper"burning, and lessens the destructive action of the charge on the kiln refractories. In the finished cement the presence of iron reduces the expansion and contraction, adds strength, adds increased resistance to"freezing and thawing, and increases the resistance of the cement to sea "or sulphate waters. [" During the past few years the construction of numerous dams through- "out the Southeast by the Tennessee Valley Authority has stimulated the "production of high-iron cements. At present a great number of specifica- "tions call for an iron cement, and the industry is supplying this demand "with a Portland cement carrying approximately 5 per cent iron oxide. "Several manufacturers are now making practically all of their cement "of this type and a number of others manufacture it as a special cement "over short periods to meet demands from the Tennessee Valley Authority "and other buyers. " The recent increase in the use of iron in Portland cement has created "a market for iron products that previously was nonexistent. The chief "sources of supply for the cement manufacturers at present are iron sand, "iron sinter and slag, and ocher. The Copperhill mining district, Ten- "nessee, supplies both iron sinter and slag for use in cement. The Carters- "ville district supplies iron sand, ocher, and some iron resulting from the "magnetic separation of iron from barite. The advantages of these "products vary according to the chemical properties of the raw materials "and the methods of handling used by the different manufacturers. Where "the iron is to be handled by conveying belts and in hopper cars, the iron"sand and sinter and slag are preferable. Where the silica content must "be raised, the iron sand is doubly advantageous because it supplies both

Jan 1, 1942

By Robert Hunt

ONE of the most serious and important economic administrative problems facing American railway authorities to-day is that of their rails, and it is one to which much thought, is being given, not only by the executive officers of the railways and the manufacturers of the steel rails, but also by State and National commissions. It is realized by many and admitted by some that the present situation is one which cannot continue. The roadways of railways must be made more secure, or the weight of rolling stock and the speed of trains must be lessened; and the desired result must be attained with the minimum outlay of money, both in expenditure on plant and in cost of operation. If the investment per mile is too large, or through the lessening of tonnage and efficiency of equipment the cost of operation is too great, the desired and demanded cheap service cannot he rendered to the public. Therefore, the weight of equipment cannot be greatly reduced, and lessening the rapidity of service would be far from satisfactory; consequently, the safety of the roadway must be secured with the least practical outlay. It is imperative that the roadbed should be properly graded, with the fewest practically possible curves; that it should have good ballast, be well drained, have good ties properly spaced, and be laid with sound rails of suitable weight, efficiently joined together, and that the whole property be carefully and intelligently cared for. My province is to treat of the sound rails. During the last few years there has been renewed interest in and discussion of that question, and I know that many rail makers not only have been and are desirous of maintaining the highest standards of manufacture which they may have attained, but have been and are seeking to better their product, in several instances devoting much time and money to that end. At the same time, they realize that the cost of any improvement in quality which they may accomplish must be kept within certain commercial bounds; and that fact is as fully understood by their patrons as by themselves, and it should be kept in mind by all who discuss the question.

Jan 2, 1914

By P. H. Mell

AMONG the minerals exhibited at the Atlanta Exhibition of 1881, soapstone, kaolin, and asbestos were well represented. The first two occur in large quantities, of very pure quality, throughout the South. The last is somewhat limited in amount, get in certain localities it exists in masses sufficiently large to pay for working; in North Carolina, Georgia, and Alabama it has ken mined with some profit. I would, in this paper, call special attention to the minerals soapstone and kaolin, because their many valuable qualities seem to have been almost entirely overlooked by our Southern manufacturers. Steatite, particularly, occurs in such large quantities, and generally in such close proximity to the great iron regions of Alabama and Georgia, that it is anlazing that the iron companies will persist in sending abroad under heavy expense for firebrick. It would require a much smaller sum of money to quarry this rock and place it at the various furnaces ; and the results obtained, I am sure, would prove its superiority over the majority of firebrick brought into this region. Soapstone, as well as kaolin, is found throughout the metamorphic regions of Alabama, Georgia, South Carolina, and North Carolina. Below will be found seven analyses that I have made of this mineral, taken from various points in the four States above mentioned. I have also subjected these same specimens to severe fire-tests, and the results were very satisfactory. The tests mere canducted in the following manner: Small portions of the compact variety were carefully weighed and placed in a Fletcher's new crucible furnace for gas, and subjected for half an hour to a heat that will in 12 minutes fuse iron. The only effect upon these specimens was a slight change in color to a darker shade, a small loss in weight, due evidently to the evaporation of water, and, in one or two specimens, a slight degree of fusion on the sharp edges. The first specimen subjected to investigation was taken from a large outcropping in Tallapoosa County, Alabama. Specific gravity, 2.88 ; hardness, 1.9; color, blue gray. Composition: Water,....2.68 Silica,..........65.48 Iron oxide,.........2.10 Alumina,.........15.02 Magnesia,... 15.35 10061

Jan 1, 1882

By R. W. Nash, A. E. Schwaneke, V. R. Miller

The Bureau of Mines developed a detector for controlling sorting devices to separate the copper-bearing fragments from the barren portion of Michigan native copper and western prophyry copper ores. A successful sorter could be used to preconcentrate the ore and eliminate costly hoisting or hauling of waste. An induction balance unit was developed and used in sorting tests on crushed sized - 2.5 + 1.3-cm (- 1 + 112- in.) ores from the Kingston (0.9% Cu) and Centennial (1.6% Cu) mines of Upper Michigan. Concentrates of 4.0% and 7.5% Cu, respectively, were obtained at recoveries of 85 and 80% of the copper in the feed. Eighty percent of the sorted ore was rejected as tailing. Sorting larger fragments improved the separation efficiency. Tests on - 10+ 5-cm (- 4 +2-in.) sized Kingston (1.6% Cu) and Centennial (2.1 % Cu) ore samples yielded concentrates of 4.3 and 4.5% Cu, respectively, with corresponding recoveries of 92 and 91 %. A bout 60% of the sorted ore was discarded as tailing. Porphyry copper sulfide ores also responded to electronic sorting but at a lower separation efficiency. Sorting response was affected by the degree of segregation.

Jan 1, 1979

NEW MEMBERS The following list comprises the names of those persons who became members during the period Oct. 10, 1918, to Nov. 9, 1918. ALLER, FRANK D., Copper Met., Ore Purchaser, American Smelt. & Refin. Co., 120 Broadway, New York, N. Y. AVÈRY, PAUL W., Met. Engr., Esperanza Min. Co., Apt. 8, El Oro, Mex., Mexico. BAKER, CHARLES A., Leaching Foreman, Copper Leaching Plant, Anaconda Copper Min. Co., Anaconda, Mont: BREED, CHARLES H Met., Crown Cork & Seal Co., Baltimore, Md. CHASE, R. L., Min. Engr 102S First National Bank Bldg., Denver, Colo. EICHELBERGER, FRANK, Vice-pres. and Engr., New York-Montana Testing & Engrg. Co., Helena, Mont. GESTER, G. C., Geol., Standard Oil Co. of Cal., 616 Standard Oil Bldg., San Francisco, Cal. GRIFFIN, JOHN, Mgr., Anthracite Territory, The Dorr Co., Board of Trade Bldg., Scranton, Pa. HAYNES, ELWOOD Pres., The Haynes Stellite Co., Kokomo, Indiana. Hsi, T. C:.. Sec'y, Tayeh Iron & Steel Works, Tayeh, China. HYDE, AUSTIN T., Mgr., Keokuk Plant, River Smelt. & Refin. Co., 607 Franklin St., Keokuk, Iowa.

Jan 12, 1918

Jan 1, 1896

By E. Cortese

Phosphate occurs in many places in Egypt, in two main zones: one in Upper Egypt, along the Nile Valley, principally on the right side, and one near the Red Sea coast. In the Nile zone, the principal layers of phosphate rock are to be found: in the mountains east of Mahamid (right side of the valley); in the hills near Sibaiya, also called Sebaieh (both sides); in the hills of Agula, Hagaza and Gurn (right side); and further on, along the camel road leading from Kena to Kosseir, a few miles east of Legheita's Oasis. Following that track, after having crossed the watershed, underlain by rocks like granite, serpentine, porphyry, and diabase, one comes again to the Cretaceous formation containing considerable quantities of phosphate, at Gebel Duwi, Gebel Nakheil, and Gebel Kosseir El Kadim, not far from the coast. More to the north, in the hills near Safaga Bay (Um El Uettat El Wasif) is another rich bed of the same formation. There are reports of phosphate existing near Suez and in the Sinai peninsula, and possibly some other zones can be traced or discovered in the future. The mines are well developed on the right bank of the Nile at Sharawna (near Sebaieh Station) and along the Red Sea coast, at Safaga and near Kosseir. Prospecting work has been done at Gebel Duwi, Gebel Gurn, Agula, Hagaza, and near Mahamid. The phosphatic formation in Egypt is quite variable, not only from place to place, but even within small areas. The phosphate is all of Cretaceous age, as is proved by the fossils found in it. It is considered to belong to the Campanian or, more appropriately, to the Maestrichtian series. The principal fossils are: Alectryonia Villei Coq. sp.; Roudereia Aures-sensis Coq. sp. = R. Drui Mun. Chalm.; Trigonoarca multidentata, Newton.; Cardita libyca, Zittel; Libycoceras Ismaely, Zittel; Nautilus sp.; Ancystrodon libycum Dam.; Corax pristodontus Ag.; Lamma biauriculata Zittel sp. Above the Maestrichtian beds, we have the Danian series, unconform-ably covered by Lower Eocene beds. Under the phosphate is a grayish marly clay, and beneath this, bluish-gray scaly shales resting on the Nubian sandstone (Santonian).

Jan 1, 1918

By D. A. J. Swinkels

The problem of determining oxygen levels in liquid steel to aid in deoxidation control has received general attention for a number of years. Work in this direction started at the B.H.P. Central Research Laboratories early in 1967 with an evaluation of sampling techniques followed by vacuum fusion analysis to determine the oxygen content of the samples (1). It was found that these techniques had a number of drawbacks if they were to be used for deoxidation control. The method of analysis was rather too slow to allow effective control and measured total oxygen level rather than dissolved oxygen. Furthermore, the results were found to be very variable due to slag entrainment in the samples. Attention therefore turned to the galvanic cell method using a solid oxygen ion conductive electrolyte such as cubic stabilised zirconia. The ionic conductivity properties of electrolytes such as (ZrO2) 85 (CaO).15 had been studied by a number of investigators and had already been applied to the measurement of oxygen activity in gases, in lower melting metals such as copper, lead, tin, silver, alkali metals and indeed the first studies in steel had been made (2,3). Since then the results of a number of studies in the development of an expendable oxygen probe for steel have been reported (4-9).

Jan 1, 1972

By R. Simon

Maurer's review1 summarizes quite thoroughly the various theoretical developments and experimental findings that contribute to the knowledge of rock mechanics in drilling. This discussion supplements Maurer's paper by including generalities that either have been incompletely treated in his review, or formulated from new considerations by the discussant and from hitherto unpublished experimental data. These generalities are associated with the observation that all mechanical methods of rock drilling essentially comprise a sequence of indexed, concentrated loadings on the bottom of the hole being drilled. A concentrated loading is defined as a mechanical loading by a tool that contacts at any one time only a small fraction of the surface of the body being worked and penetrates only a small fraction of the body thickness. The surface in this application is the bottom of the hole. The deformation of ductile material by concentrated loading has received considerable attention because of the importance of indentation tests for measuring hardness of metals. Some of the generalities involved in concentrated loadings on ductile materials apply also to concentrated loadings on more brittle materials such as rock. Among these generalities is the applicability of similitude considerations to scaling laws and to force-displacement and energy-volume characteristics for tools of various shapes, as summarized by Tabor.2 Vork on the flow and fracture behaviors of glass loaded with pyramidal and spherical indenters is reviewed by Douglas.3 Maurer refers to the work of Evans and Murrell on wedge loadings on coal and on mixtures of pitch and sand. It is evident from Maurer's paper that a considerable portion of the studies of rock mechanics in drilling, such as crater formation experiments, has involved concentrated loadings on rock.

Jan 1, 1967

By N. A. Elmslie

This subject covers much ground, therefore it must be treated in a general way rather than in detail in this paper. Personnel To approach the measure of a mine, it is, of course, essential that the personnel be measured, and this measuring must be done in a circumspect manner and conclusions must be reached slowly. There may be one unit in the personnel of an organization that may be out of step with the remainder of the organization, not always because of lack of ability, but because of misplacement or lack of proper measurement of his capabilities. Too much time can scarcely be spent in the study or measure of the personnel ; in fact, a manager or a superintendent of a mine never completes his work along this line. Mine or Plant Just as no two men are alike, so no two mines or plants are alike; and yet there are many similarities. Find out what the similarities are, and this will help to make clear the dissimilarities. Try to visualize details of the difficulties, not because you will have to deal with them yourself, but to consider them in later studies of general problems. To outline all the steps to be taken in familiarizing oneself with a plant or operation would be impossible, but the following points may be of interest in any investigation. The study of a mine is generally made backwards-—that is to say, one sees the finished product first-—-but this is immaterial, because each step must be considered separately in any event. As a rule, there are certain heads under which the different features of mining can be placed, as follows: Ventilation.—Ventilation is usually the most important item in power cost and safety, especially in gassy mines. Quantity of air, water gage and power consumption, and finally analysis of the return air in full return and separate splits should be considered. Type of fan and type of power unit should enter into this study because it is important to view expenditures which are going on 24 hr. a day and 36.5 days in the

Jan 1, 1931

By A. Hansson, G. E. Tardiff

WHILE it is generally known that cold-worked low-and medium-carbon steels exhibit substantial increases in tensile rupture ductility with increased deformation velocity172 (up to the von Karman limit), the observations for annealed or normalized steel do not permit simple generalization. Various investigators, for example, have reported both small increases1,3 and small decreases4,5' in rupture ductility with increased rates of deformation of normalized low-carbon steel. The purpose of the present note is to report on the dependence observed for strain-aged steel since preliminary work here indicates that strain aging results in the development of a consistent type of behavior that is understandable in the light of current knowledge of the lower yield dynamics for steels which deform inhomogeneously.6 This realization throws additional light on the influences responsible for the behavior of normalized steel. The results presented here were obtained for a 0.21 pct C, 0.012 pct N sheet (0.012 in. thick) steel which was received in a temper-rolled condition (approximately 3 pct reduction in thickness after process annealing); the as-received material had a spherodized structure with a ferritic grain size of ASTM 8. The material was selected for testing after 6 months room temperature aging, at which time the static lower yield and ultimate tensile strength measured 79 and 82 kpsi, respectively. ASTM 2-in. reduced section, 1/2-in.-wide specimens were used in smooth bar tests and 3/4-in.-wide specimens containing two 60-deg opposed edge notches (root radii = 0.002 in.) were used in notched bar tests. To facilitate strain measurement, the smooth bars were blued with ink and marked at 0.1-in. intervals along the gage length; the notched

Jan 1, 1968

By Karl S. Kurtenacker

In attempting to find a rapid and economical means for solving many of the subsurface problems that confront the highway engineer, the author for the past two years has utilized a Megger Ground Tester on resistivity surveys in conjunction with highway construction. Electrical surveys in connection with highway work are largely shallow depth surveys, thus differing from most other types of resistivity work. Consequently, the readings are affected by a great many qualifying factors such as the density and moisture content of the media under observation and the amount of weathering and leaching. In most cases the surface layer is decidedly heterogeneous in character, and, because of the great number of side hill cuts, the second layer, which in most cases is rock overlain by some sort of surface soil, silt, or debris, seldom lies in a horizontal position. Shallow strata, lacking homogeneity and not lying in a horizontal position, do not lend themselves readily to accurate theoretical interpretations, therefore the author has used empirical rules to a large extent in interpreting depth soundings. The following empirical rules of interpretation are surprisingly adequate for highway work, since much of the work is in the nature of reconnaissance surveying and the results are construed to be approximations. The writer is careful not to risk interpretation on some special feature of the curve, since such features are usually due to random errors or lack of homogeneity among the subsurface strata. Effect of Surface Medium A resistivity depth sounding taken to a depth of 200 or 300 ft. is not much affected by superficial conditions, but these conditions have a great effect in depth soundings to 25 or 30 ft. In shallow soundings the character of the surface medium has a very marked effect on the entire resistivity graph. Fig. 1 illustrates a very striking example. Graphs A and B are depth soundings taken in approximately the same place. The surface stratum is a clay loam but at the place where graph B was taken

Jan 1, 1934

By Mark Malamphy

DURING colonial times, Brazil was famous for the richness of her alluvial gold deposits. Paul Ferrand has estimated that the gold produced during the period from 1700 to 1820 was the equivalent of some 64 million pounds sterling. Since that time, most of the more prolific alluvial deposits have been exhausted. A few gold mines are still func-tioning, notably the Morro Velho mine, which is one of the deepest mines in the world. Today, the gold production of Brazil is insignificant when compared with world figures, but there are still many gold-bearing regions and it is probable that in at least some of them profitable returns would result from an exploitation program taking advantage of all the most modern innovations in gold mining and ore treatment on a large scale. In order to demonstrate the value of some of these abandoned pros-pects and stir up interest in increasing the national gold production, the government has stimulated research. Experimental plants have been and are being established in various places, and tests on large quantities of ores are being carried out on a semicommercial basis. The Geological Survey of the State of Minas Geraes is very active in this line and the Federal Institution is also showing an increased interest in the matter. One of the lesser known gold-bearing regions of Brazil is in the vicinity of Lavras, in the State of Rio Grande do Sul. Gold was first reported from this region in the early part of the nineteenth century. In 1811, D. João VI sent an experienced prospector from Minas Geraes to investi-gate the validity of the reports. According to the reports of Baron

Jan 1, 1934