Search Documents

The Pinto Valley, Arizona, plant of Cities Service Company is one of the newest copper producers in the United States, having started production in 1975. It is located a few miles west of Miami, Arizona, on the site of the Castle Dome Mine, a World War II operation which was shut down and its mill later moved and renamed the Copper Cities plant. The Pinto Valley concentrator uses six 18 ft (5. 5 m) diameter by 21 ft (6.4 m) long, 4000 hp, single-stage ball mills, taking crushed ore from four 7 ft (2. 13 m) standard and eight 7 ft shorthead crushers. It has a design capacity of 40,000 stpd but has higher tonnage capability for an expanded concentrator. The copper porphyry-ore is mined by two 15 yd and one 20 yd shovels (11.5 and 15.3 cu m) and is transported to the primary crusher by 150-ton trucks. The dump pocket is relatively shallow (14 ft or 4. 27 m deep); and because of the width necessary for the 150-ton trucks, it was designed to use the ore itself instead of manganese steel as an abrasion- resistant lining, although a heavy steel cap protects the dump pocket top edge. The pocket has a capacity of 300 tons of ore. Water sprays under the dumping positions direct a fog toward the truck being dumped for excellent dust control. Breaking of oversize is done by a hydraulic impact breaker mounted on a hydraulically operated articulated arm situated at the side of the dump pocket. Again because of the shallow pocket, no splitter is used to protect the spider of the 60 in. by 89 in. Traylor gyratory crusher, which is equipped with a hydroset mechanism. Crushed ore at 8 in. (203 mm) drops into the 360 st surge chamber lined with AR plate and then is fed directly to the 60 in. (1.52 m) stock- pile conveyor by an 84 in. by 20 ft (2. 13 m by 6.1 m) four-speed apron feeder at a rate of up to 4000 stph. Early in 1977, Cities Service will replace the four -speed electric drive with a hydraulic pump and motor with infinitely variable speed. They are also studying the replacement of the apron feeder with an 8 ft wide (2.44 m) belt feeder similar to those at Similkameen and Palabora. Peak crushing capacity would then be increased to 5000 stph. The AR plate in the crushed ore pocket was installed in large, rectangular sheets which required much less embedded metal to hold it in place than would the more conventional, smaller arid square pieces of cast manganese steel. For duty in the crushed ore pocket, where wear is not severe, the AR plate is a satisfactory material. The new Palabora Figure-8 crusher also uses this design.

Jan 1, 1978

The San Manuel district of Arizona was first prospected prior to the Civil War, but there was little or no production until 1881. Small operators tried to develop ore bodies from time to time after that without success. Then, in 1917, a drilling program was carried out; but it did not indicate a copper content of interest. Finally, in the 1940s, the U. S. Geological Survey drilled the property and obtained indications of a mineralized area. At that time, Magma Copper and its principal owner, Newrnont Mining Corporation, drilled many deep holes through the gravels and conglomerates and in 1948 proved an ore reserve of 367 million tons of 0.785% copper sulfide ore. Underground exploration and development were started in early 1948, and in 1953 design and construction of the surface facilities commenced. By the end of 1955 plant construction was completed. The ore deposit of disseminated pyrite, chalcopyrite, chalcocite, molybdenite, silver, and gold is in quartz monzonite porphyry gangue. Mine production, which is entirely underground, is by full-gravity block-caving. Initially, ore mined at a rate of 36,000 tpd was hoisted through two identical shafts. From the 5,000 ton coarse ore bins located at the collar of each shaft, the ore was hauled by a shuttle service rail- road in 100-ton bottom-dump rail cars a distance of seven miles to the rail bin. Fragmentation from block-caving supplemented by underground grizzlies at the loading stations controlled the oversize material to give a feed size acceptable to the two 7 ft standard Syrnons crushers. During operation, however, it became evident that a large amount of secondary breaking in the grizzlies was necessary to produce a suitable feed for the standard crushers. The decision was then made to install primary gyratory crushers on the surface adjacent to the shaft site ore bins. Under each 5,000-ton coarse ore bin, an 8ft by 20 ft (2.44 m by 6. 1 m) apron feeder transfers the ore to a 13 ft 6 in. by 10 ft (4. 1 m by 3. 05 m) grizzly set at 6 in. (152 mm) and sloped at 45 degrees. About 65% of the ore passes the grizzly and thus bypasses the 42 in. by 65 in. (1.07 m by 1. 65 m) Allis -Chalmers gyratory equipped with a Hydroset mechanism and having an open side setting of 5 ½ in. (140 mm). Grizzly undersize and crushed ore drop onto a 6 ft by 30 ft (1. 83 m by 9. 14 m) variable- speed apron feeder for transfer to a 54 in. by 90 ft 5 in. (1.37 m by 27.6 m) inclined conveyor equipped with a tramp iron detector. Indication of tramp iron automatically stops the conveyor and both apron feeders. When the iron is removed from the belt by the operator,

Jan 1, 1978

By George A. Morrison

A deposit Of limestone Was known to exist at a depth of 2000 ft under the property of the Columbia Chemical Division of the Pittsburgh Plate Glass Co. at Barber-ton, Ohio. A 662-acre site was selected for the projected mine, some two miles northwest of the plant and near the main line of the Erie Railway. An electric railway 8800 ft in length connects the mine and the plant. The deposit is overlain by 18 ft of un-consolidated (sand and gravel), 100 ft of water-bearing sandstone, and finally 2080 ft of shale into which thin layers of sandstone are embedded. The limestone bed itself is 345 ft thick and overlies 200 ft of gypsum. A 300-ton-per-hour capacity mine was decided upon. Two shafts were deemed advisable, one for production and the second for service; and these were sunk 550 ft apart, one to a depth of 2323 ft and the other to 2258 ft. Each is 16 X , ft in the clear and timbered with 6-in. steel H-sets on 8-ft centers, using 3/8 X 4 X 4-in. angles as studdles. Twelve inch I-beams were used at 160 ft intervals as bearers set in deep hitches and concreted to a vertical depth of 8 ft. Wooden sheathing was first employed but sloughing of the shale created a pressure on this lining and finally concrete was deemed necessary. Water was encountered only within the first 315 ft, flowing at 60 gpm and by grouting this was reduced to 15 gpm. Temporary wooden sinking headframes were installed with 300 cu ft capacity storage pockets and with doors automatically controlled by air cylinders by hoistmen. Each shaft was operated on four 6-hr shifts. The usual V-cut was drilled at the center of the shaft and the round consisted of 34 holes- A 40 pet gelatin dynamite was employed with some 60 pet in the cut holes. Drilling crews consisted of four to six men. Shale drilled easily but became more bed in depth and sandstone wore away the gauge Of the bits rapidly. A room-and-pillar mining system was adopted whereby rooms turned off on 80-ft centers, each room 40-ft wide and 50-ft high. Rib pillars between rooms were cut into 100 ft lengths by frequent holes. Ventilation is achieved through the two shafts, the down-draft through the service shaft, and the return through the pr0duction shaft. The hoist has a a Of 300 tons per hour and is equipped with 10-ton balanced skips requiring. a 2-min cycle Or 30 trips Per hour- Hoisting is designed to Operate by automatic loading and no hoistman is required for normal Operation. The 48 X 60 in. jaw primary crusher is underground. It is fed through chute and chain feeders and is flood-oil lubricated and cooled. An inclined belt conveyor returns oversized material to the crusher. Tramming is by Diesel-powered trucks.

Jan 1, 1948

By J. A. Ede

The object of the writer is to call attention to a rather unique aggregation of economic products distributed over a line of succeeding formations about 3 mi. long, to be seen within a few miles of La Salle, Ill. Fig. 1 is an ideal section of the stratification exposed and exploited along a distance of 3 1/5 mi. in a southwesterly direction from the quarry of the Utica Hydraulic Cement Co. located near the historic site of Kaskaskia village to the Oglesby shaft at Oglesby. No attempt has been made to cover the whole field, special mention only being made (with the exception of two places) of the operations found along the course or parallel to the direction assumed in the ideal section. I have used Fig. 2, after J. R. Bent and De Witt Kelly, to locate the relation of the La Salle anticline to the coal mines of this district and to show the operation of No. 1 and 3 mincs of the Illinois Zinc Co. Anticline and the Rock Formations Owing to the structural deformation between La Salle and Utica, the older rocks of the state are exposed to the surface along the northern embankment and the bottoms of the Illinois River valley near the latter place. At; the Illinois Zinc Co. works, Sec. 16, Tp. 33, R 1, a well for water mas sunk 1828 ft. and samples taken every 10 ft. of the ground penetrated; duplicates were sent to Mr. Cady of the Illinois Geological Survey. A general compilation or synopsis study of this section is here presented. As the well is over 1 mi. west of the Western limb of the anticline, the section affords some reliable data. These samples were studied and interpreted by H. M. DuBois as Lower Magnesian, and by G. H. Cady as the Lower Magnesian. The results are given in Fig. 3. The most interesting geological feature of this district is the La Salle anticline. In 1865, Leo les Quereux, looking at Split Rock, asked how it happened that the upper coal measures overlie strata of the Lower Silurian and what has become of the formations which are generally found intermediate—the Upper Silurian, the Devonian and sub-carboniferous, and the lower member of the coal measures?

Jan 1, 1920

MORE than 5000 miners and suppliers descended upon Denver to make the American Mining Congress' four-day metal mining show one of the most extravagant equipment displays ever assembled in one place at one time. The most recent developments in equipment for mining, milling, and processing ore were shown by the 146 exhibitors at Denver's new City Auditorium which covers 57,000 sq ft of floor space. Other displays were placed in the open air opposite the auditorium site. Registration desks were opened Sunday, Sept. 21. A field trip to the Colorado School of Mines at Golden was the featured activity of the day. Official opening of the show took place on Monday, and presided over by Howard I. Young, president of American Zinc, Lead & Smelting Co.; Otto Herres, vice president, Combined Metals Reduction Co.; William J. Coulter, vice president, Climax Molybdenum Co.; Charles B. Stainback, Westinghouse Electric Corp.; and Merrill E. Shoup, president, Golden Cycle Corp. Convention welcoming addresses were delivered by a representative of Mayor James Q. Newton, of Denver, and Gov. Daniel V. Thorton of Colorado. Following the formal opening ceremonies a round table discussion dealt with the "Paley Commission Report" formally called Resources for Freedom. Participating in the panel were: Arthur H. Bunker and George R. Brown, members of the Paley commission; H. I. Young, president of the American Mining Congress; Horace M. Albright, president of U. S. Potash Co.; Evan Just, vice president, Cyprus Mines Corp.; Donald H. McLaughlin, president, Homestake Mining Co.; E. H. Snyder, president Combined Metals Reduction Co.; Simon D. Strauss, vice president, American Smelting & Refining Co.; Sen. H. C. Dworshak (R.-Idaho) ; Ira B. Joralemon, consulting engineer; Jess Larson, De fense Materials Procurement Agency; and Andrew Fletcher, president of St. Joseph Lead Co. The panel discussed the report for six hours, adding a great deal of information to the already voluminous amount which has been gathered concerning it. Three objections to the report frequently mentioned were: 1-the multilateral contract; 2-international buffer stocks; 3-international buffer stocks combined with limited quota arrangements. Points on which the panel commended the report were its recommendations for acceleration of topographic and geologic mapping of the United States and Alaska; recognition of the principle of percentage depletion for metals and minerals; and advocation of removal of the present limitations on the expensing of exploration costs applicable to minerals. Technical sessions were held throughout the four days of the meeting. Included in the program were: Progress in Mechanication; Small Mines; Public Lands; Open Pit Mining; Manpower-Labor Relations; Shaft Sinking; Roof Support; Taxation, Gold, Silver and Monetary Policy; Advances in Mill Practices; Special Conference on Strategic Materials; Uranium Mining-Atomic Energy; Prospecting and Exploration; New Metallurgical Processes; and Rock Breaking. About 45 papers and several panels were presented during technical sessions. Formal and informal social functions consumed the remaining time of the convention. Three locations were needed to handle the huge throng attending the Mining Jamboree Monday evening. The only other sponsored social function took place Thursday evening. A great many informal gatherings, chiefly convivial, were held in manufacturers' courtesy rooms-called wet stopes. Field trips included Cripple Creek, Pueblo, Climax -Leadville-Gilman, Colorado Plateau-Grand

Jan 1, 1952

By D. H. Polonis, M. B. Kasen

AN unusual thermal etching phenomenon has been observed on the surface of a Cu-Si alloy. The observations were made during studies of vacancy condensation pit formation which were reported in previous papers.1,2 Figs. 1 and 2 are photomicrographs of the surface of a Cu-4.8 pct Si alloy after heating in vacuo (3 x X mm Hg) to 525°C and subsequently holding at that temperature for 16 hr in an impure (air-contaminated) argon atmosphere. Under these conditions preferential removal of silicon from the matrix by oxidation results in a surface which is entirely a phase overlying an a plus y structure. The light areas of Fig. 1 are regions in which very little thermal etching has occurred, while the majority of the surface has experienced severe etching. Similar regions in Fig. 2 are seen as plateaus above contours produced by net transfer of material from the specimen surface. Twin boundaries are also visible in Fig. 2. The difference in matrix mi-crostructure between Figs. l and 2 reflects the par- ticular orientation of low-index planes with respect to the surface of observation. Thermal etching contours of this type have been studied in detail by Hondros and Moore Both of the photomicrographs show that one or more dark spots are located approximately at the center of every protected area; where two spots are in close proximity, the protected areas have merged. The microstructures indicate that the anomalous resistance to thermal etching is related to the presence of these spots. Williams and Hayfield have shown that local regions of unusually high oxidation resistance can be caused by a surface monolayer of atoms with a work function higher than that of the base material. The result is an inhibition of the rate of electron removal from the base material and a decrease in the oxidation rate. The source of the protected layer may be either surface diffusion from contaminants on the specimen surface or pipe diffusion of solute atoms followed by migration across the surface. In the latter case the driving force is a difference in chemical potential resulting in a Gibbs adsorption phenomenon. In the present case, chemical polishing of the specimen surface precluded contaminants of a strictly surface nature. Consequently, diffusion of impurity atoms from within the lattice appears to be the most tenable explanation of the observed phenomena. The authors propose that the structures of Figs. 1 and 2 reflect the diffusion of impurity atoms along extended dislocations within the individual a phase grains prior to surface oxidation. The central spots within the protected regions are seen as sites of dislocation emergence which have become locally decorated with oxide in the manner discussed in Ref. 1. Williams and Hayfield observed protected regions adjacent to the grain boundaries of iron-contaminated copper which they attributed to the segregation of iron to the grain boundaries coupled with high dif-fusivity along the complex dislocation array at such boundaries. No evidence of such grain boundary protection was observed in the Cu-Si alloy; this

Jan 1, 1964

By C. S. Yust, C. S. Morgan

ThIS note reports the observation of masses of dislocation etch pits around the weld necks of small single-crystal particles of calcium fluoride sintered to a cleaved face of a larger CaFz crystal. Crystal particles in the -50 +I00 mesh size range were placed on freshly cleaved CaFz surfaces and heated at 1250°C for 30 min in a tantalum container in an argon atmosphere. The sintered specimens were then etched at room temperature for 40 to 50 min in a 2 pct sulfamic acid solution which is a selective etch for dislocations in caF2.' Figs. 1 through 3 show the masses of dislocation etch pits observed around weld necks after etching. In some cases, particles were gone after removal of the specimens from the furnace although weld necks were readily visible. In other instances, no etch pits formed around a weld neck. A possible cause of concentrations of dislocations on the crystal surface is mechanical deformation of the base crystal when particles are dropped on it. If such a deformation does occur, it would be much smaller than that caused by the light punching of a crystal with a sharp instrument which results in large concentrations of etch pits. However, crystals deformed by punching with the sharp instrument and annealed at the conditions of these experiments (1250°C for 30 min) before etching showed no concentrations of dislocation etch pits. It is obvious that dislocations from the much smaller deformations, possibly created when particles are placed on the surface, would also anneal out. Etching of large crystals which had particles placed on them in the usual manner but which were not heated showed no dislocation concentrations such as shown in Fig. 1. The magnitude of dislocation etch-pit concentrations did not vary with extensive variation of the cooling rate. The appearance of many of the etch-pit clusters is typical of a well-annealed condition, indicating that the dislocation concentrations formed before the specimen temperature was lowered. Therefore, it is evident that thermal stresses in the neck area did not create the deformation indicated by the presence of the dislocations. The possibility exists that the etch-pit concentrations at places where particles had been removed may be the result of deformation accompanying the fracture of the sintered bond. That this is not so was demonstrated by breaking off particles around which no etch pits occurred. Re-etching never resulted in the large concentrations observed at sintering sites. The stress available to effect material movement during sintering of two particles will depend on the geometry at the contact point but can easily exceed the macroscopic yield stress in CaFz systems. It appears that the plastic deformation observed results from sintering or simply from the weight of the small particles. It has been previously argued that plastic flow makes an important contribution to the initial densification of oxides having the fluorite crystal structure.2p3 If plastic deformation occurs, it would begin as soon as the temperature is sufficiently high

Jan 1, 1967

By Jon J. Connor, Richard J. Ebens

The trace element geochemistry of the cherty clay-rich carbonate residuum cover in much of southern Missouri and adjacent parts of Arkansas was investigated during the earl 1970's as part of a statewide geochemical survey of Missouri.1-8 The study was environmentally oriented and focused on the character of the "natural" geochemical environment of the state. A great deal of effort was made to collect samples that would represent the geochemical variability of the near-surface environment in an unbiased way. In general, this was accomplished by use of randomization procedures in both collection and analysis. Most of the sampling sites were selected randomly to prevent personal bias from entering into sample selection. In the laboratory, samples were analyzed in a randomized sequence to circumvent the effects of any systematic bias that may have entered into the laboratory procedures. Several residuum samples contained 1000 parts per million (ppm) or more of lead, zinc, and barium. All these samples were collected in Washington County in or near the barite district. The frequency distributions shown in [Fig. 1] indicate just how unusual the residuum in Washington County is with regard to these three metals and copper. The shaded parts of the histograms represent the samples from Washington County. The histograms are based on analyses of 141 samples from 38 localities scattered over the subcrop of the Cambrian and Ordovician formations of southern Missouri and northern Arkansas. Eight localities were selected randomly from over each of four bedrock units-Bonneterre dolomite; Potosi and Erninence dolomites; Roubidoux formation; and the Jefferson City, Powell, and Cotter dolomites. Six localities were selected randomly from over the Gasconade dolomite. The geochemical "background" for these elements in residuum is defined by samples from outside of Washington County (unshaded part of the histogram); lognormal distribution curves have been fitted to the corresponding parts of each histogram. Clearly, these lognormal models (curves) describe well the background distributions of zinc, barium, and copper. The background histogram of lead concentrations is notably skewed to the right compared to the model. Lognormal distribution curves were also fitted to the data on lead, copper, and zinc in the residuum of Washington County. No model was fitted for barium in Washington County because of the distinct bimodality in the data. All samples containing more than 1000 ppm were collected in the barite mining district and obviously reflect the elevated levels of barium in the district. The frequency distributions for Washington County are clearly anomalous with respect to the background data, those for lead, zinc, and barium being exceptionally so. The models for anomalous lead, zinc, and copper seem to fit reasonably well, although the scatters in the lead and zinc anomalies are considerably larger than the scatters in the corresponding background data. The copper anomaly, although probably real, is greatly subdued compared to that of lead and zinc. Also, it has a scatter similar to that of the copper background, rather than being enhanced like the scatters of the lead and zinc anomalies. On the basis of techniques described by Miesch,4 the chemical abundance of copper, lead, and zinc in residuum in

Jan 1, 1980

By S. F. Reiter, You-Chao Liu, W. R. Hibbard

Cyril Stanley Smith in his classic 1948 Institute of Metals Lecture&apos; noted in the case of annealing twins that: "It is well known that approximately the same number of twins per grain and the same general geometry are maintained in large grains as in small ones, a fact that certainly suggests a mechanism such as the above where boundaries and twins grow proportionately together. If this view is correct, a spherical grain should have no mechanism for keeping its twins." Such a constancy of twins per grain would be of particular interest as a tool for the study of the origin of annealing twins. It has been proposed by Mathewson2 and later by Barrett3 that in face-centered cubic metals slip occurs in the {111} Plane by <112> shears which combine in pairs to produce the macroscopically observed <110> movement. This proposal is schematically inviting since <112> slip permits the atoms of one plane to move along the interatomic valleys of its neighbor rather than up the hills across the atom sites. There is strong experimental evidence? that annealing twins result from the growth of nuclei in the form of "twin faults" produced by single <112> shears. It is possible that more twin faults would form at low deformation temperatures than at high ones, because the more rigid lattice may increase the tendency to "freeze" the twin faults and prevent their dissipation in slip. This is suggested by (1) the greater resistance to slip at low temperatures and (2) greater tendency toward mechanical type twinning at low temperatures (a summary of these factors is presented by Seigle and Brick5). These considerations would suggest the following: a. Constant twin/grain ratio for specimens deformed constant amounts at a constant temperature, but annealed at various temperatures above the recrystalliza-tion temperature. b. Larger twin/grain ratios for re-crystallized specimens previously deformed constant amounts at lower temperatures. The purpose of this investigation is to test these considerations. One half in. rods of phosphorous deoxidized electrolytic copper and 70-30 alpha brass (68.36 pct Cu, 0.005 pct Pb, 0.01 pct Fe, 31.62 pct Zn remainder) were rolled to a thickness of 0.350 in., milled to specimens 0.350 X 0.437 X 2 in., and annealed at 700°C to an average grain size of 0.065 and 0.090 mm, respectively. These specimens of each metal were then rolled 50 pct reduction in thickness and annealed one hour under conditions which were all combinations of the following: Rolling Annealing Temperatures. Temperatures. °C °C -70 400 25 500 200 600 Standard metallographic techniques&apos; were used to prepare specimens. By the method of lineal analysis7 using a minimum of ten samples of fifty grains each for each specimen, the ratios of twins* per total grains, twins per twinned grain, twin families* per total grains and twins per twin family were determined. Recrystallized grain size was determined by A.S.T.M. comparison methods.8 All observations were made on the rolling plane. The results are tabulated in Table 1.

Jan 1, 1950

By R. E. Ogilvie, N. L. Peterson

DURING the past few years there has been considerable effort devoted to the understanding of radiation effects on materials. The concept of the Frenkel defect and other lattice defects suggests that radiation may alter the rate of many metallurgical phenomena, especially those which are diffusion controlled. In 1953 R. R. Coltman and T. H. ~lewitt&apos; found an appreciable effect on the ordering rate of Cu,Au due to fast neutron bombardment. Since then several rather comprehensive theories have been proposed on radiation enhanced diffusion in solids.2"4 If the energy of the radiation is above the threshold energy for the removal of atoms from their lattice sites, Frenkel defects will be produced. These defects can be produced uniformly throughout a relatively thick specimen by high-energy X-rays permitting bulk property studies without the limitation of sample dimensions. In this work high-purity arsenic containing 30 ppm of impurities was allowed to diffuse from the gase- ous phase at 700°C into single crystals of p-type germanium containing 0.1 ppm of indium. As the arsenic diffuses into the P-type germanium, an n-type layer will form in the diffusion zone. At the p-n junction the concentration ratio of the arsenic to the indium is constant. Experimental Procedures—The germanium specimens, 10 mm by 10 mm by 5 mm, were polished and etched to a mirror finish. The specimens were then sealed off in a vycor glass capsule at 3 x 10"5 mm Hg pressure with a sufficient amount of arsenic powder to produce a one-half atm pressure of arsenic at 700°C. Specimens were annealed at 700°C without radiation. The diffusion coefficient determined from these samples agrees within 8 pct of previous work done by Fuller.&apos; Three specimens were given diffusion anneals at 700°C in a small tube furnace centered beneath the target of a 2-mev Van de Graaff generator. The specimens when in the furnace were 10 cm directly below the target of the generator. These specimens were irradiated continuously during the diffusion run with the Van de Graaff operating at 2 mev with a tube current of 225 to 250 pamp. The intensity of the x-radiation at the surface of the specimen inside the furnace was approximately 4.5 x l05 roentgens per hr. The temperature was controlled within m2°C by a chromel-alumel thermocouple throughout this work with no observed temperature change due to the radiation. By careful lapping, the samples were polished at an angle of 5 deg to the diffusion zone, giving a XI0 increase in the visible diffusion zone. The location

Jan 1, 1960

F. W. Matthiessen, who, with E. C. Hegeler, of La Salle, was one of the creators of the zinc industry in the-United States, was born in Altona, Schleswig-Holstein, Germany, Mar. 5, 1835. He was one of a family of remarkable brothers, two of whom were long absociated in this country with the sugar and glucose industry. Mr. Matthiessen was educated at Freiberg, and came to this country in 1857 with Mr. E. C. Hegeler, after having, in company with that gentleman, visited the mining districts of Germany, Belgium, and England. They first went to Friedensville, near Bethlehem, Lehigh County, Penn., wherc attempts had already been made to produce zinc from the ore deposits found in that place. The ore was a he silicate but all attempts to extract zinc from it had failed. Mr. Matthiessen and Mr. Hegclcr were successful, but declined to invest their money in the zinc industry at Bethlehem because 01 certain local conditions. Hearing of the discovery of zinc -ore in the West, they visited both Wisconsin and Missouri and thought of settling in the coal region of East St. Louis. Finally La Salle, as being near to the Wisconsin fields and having much coal, was selected ae the site of the new smelting company, and on Dec. 24, 1858, the first shovelful of dirt was turned for the buildings of the new industry. The Civil War at first interfered with the manufacture of zinc, but afterward a lively demand for the metal arose and the future success of the institution was established. A large rolling mill was added in 1866, and in 1881 the manufacture of sulfuric acid as a byproduct was begun. Mr. Matthiessen also developed the Western Clock hlanufacturing Co. of La Salle, which manufactures the Big Ben alarm clock, from a small plant having 25 men to the present large institution which employs some 2000 workers. Mr. Matthiessen&apos;s affiliations with other metal industriefi have been numerous. But the contributions of the great zinc manufacturer to the causes of philanthropy and education have made his name known throughout the country, beyond industrial circles. He has given to the city of La Salle probably a sum total of $500,000 in various benefactions. Among the objects of his philanthropy were the La Salle-Peru Township High School, which he has made a model institution of secondary education for the entire United States; also the Tri-City Hygienic Institute of La Salle, Peru, and Oglesby, Ill., which he endowed for $200,000 This Hygienic Institute, which is unique in the United States, has a traincd staff of health officers, bacteriological laboratory, medical library, infant welfare station, milk station, free dental clinic, school nurse, and isolation hospital. Mr. Matthiessen was elected mayor of the City of La Salle three times and gave generously to the municipality of which he was the head. He also saved for the people of Illinois one of the great scenic districts of the state, Deer Park, with its cafions and natural beauties, which he con-verted into a model scenic resort, and the proceeds of which he gave to the charities of the Tri-Cities in which he lived. He died on Feb. 11, 1918.

Jan 1, 1920

By J. M. W. Mackenzie

A microelectrophoresis technique has been used to measure the zeta potential of quartz over a range of pH and ferric iron concentration. The results have been discussed in terms of the adsorption of ferric cations and ferric hydroxide to the quartz surface. Possible relationships between the experimental results and the flotation of quartz have been examined. The adsorption of multivalent cations at the surface of quartz has been studied by many investigators who have used a variety of experimental techniques ranging from streaming potential 1 to radiometric2 measurements. Two possible mechanisms of cation activation of quartz have emerged from the results of these investigations viz: the adsorption of the cation to the negatively charged quartz surface, followed by adsorption of the collector anion to the adsorbed cation site, or: formation of a cation-collector complex which is then adsorbed to the quartz surface. In many natural and industrial systems one of the most prevalent activating species for quartz is ferric iron, this is especially so in the acid-circuit, anionic flotation of iron ore. The adsorption of ferric iron to the quartz surface is complicated by the ability of ferric iron to form complexes with anions, a phenomena which is of minor importance in one of the most widely studied quartz activation processes, ca ++ activation.* *The pK value for [ca(oH)+]/ [ca2+] [oh-] is 1.46 indicating that the influence of Ca (OH)+ ions will be minor in all but strongly alkaline solutions. In order to obtain a better understanding of quartz activation by ferric iron the zeta potential of quartz in the presence of ferric iron has been measured over a range of pH and ferric iron concentration. EXPERIMENTAL METHODS Materials: Selected samples of "rock clystal" quartz from New England, N.S.W., were ground in a pebble mill, washed for three hours in boiling concentrated hydrochloric acid, washed in hot chromic acid and then washed repeatedly with distilled water until the washing water gave no trace of chloride ion.

Jan 1, 1967

By H. H. Podgurski

Above 200°C the observed increase in the apparent solubility of hydrogen in low alloy steels caused by cold work is attributed to the formation of methane in microvoids. This methane can be isolated quantitatively, and furthermore, the amount of methane is in accord with the equilibrium 2H2 + Fe3C = CH4 + 3Fe. The micro-void volume, calculated from the methane content via the equation of state for methane, corresponds approximately to that calculated from the measured density decrement produced by cold work. THIS investigation was undertaken with the intent of employing the hydrogen atom as a probe in detecting specific crystallographic defects in cold worked steel. It was expected that different degrees of chemical interaction of hydrogen with the various types of defects could be utilized. The original aim was to assign concentration values to defect sites. The success of this approach requires that experimental conditions can be attained under which lattice-dissolved hydrogen equilibrates primarily with only one type of defect. A set of experiments which appeared potentially to embody these requirements was described several years ago by Keeler and Davis.1 They noted in the case of a mild steel (low carbon) that the solubility of hydrogen between 200° and 400°C near atmospheric pressure was notably increased by cold working the steel. The observed solubility was an order of magnitude greater than the normal lattice solubility. * Although the Keeler and Davis studies suggested that the density decrement effected by their cold-working operation might be related to the anomalous solubility of hydrogen, they offered no explanation of the relationship between the two effects. Prior to this work, Darken and smith3 had noted a similar effect of cold work upon enhanced sorption of hydrogen by steel when charged by acid pickling. In the light of present-day concepts, interaction between lattice-dissolved hydrogen and dislocations was strongly suggested. More recently, Hill and Johnson,4 working with a

Jan 1, 1962

By M. Yoshinuga, S. Watanabe

Some iron ores, sinters and pellets occasionally show abnormal behavior during reduction which makes them undesirable as blast furnace burden. These may be divided into the following three types: (1) decrepitation of iron ore, (2) swelling of iron ore and pellet, (3) size degradation of sinter. In this paper reduction experiments and microscopic examinations were made to clarify the mechanisms and causes of these abnormal phenomena. Decrepitation occurs mainly when compact hematite ores containing small amounts of limonite are heated to about 500°C. Abnormal swelling of ores and pellets is caused by the rapid growth of fibrous metallic iron from the surface of wustite grains during rapid reduction and is fundamentally related to their original microstructure. Size degradation of sinter occurs through the development of cracks in the reduction stage from hematite to magnetite. About 80% of the iron ore used in Japan&apos;s blast furnaces comes from abroad, and the iron and steel industry must import this raw material from distant overseas places at high freight rates. The blast furnace operators, therefore, have made strong efforts to cut costs under these restrictive raw materials conditions by increasing productivity and simultaneously decreasing coke consumption. If, however, a high proportion of the ore burden consists of unsuitable materials furnace irregularities often result, establishing the need for detailed investigations of the basic natures of the ore constituents and their reactions during the reduction process. Recent investigations &apos;-&apos; of various ore burdens suggest that some iron ores, sinters and pellets are occasionally abnormal in appearance and behavior during reduction studies and may prove to be undesirable for use in the blast furnace. In the present study reduction experiments and microscopic observations were made to clarify the causes and the mechanisms of the abnormal behavior observed in some constituents of the burden and their effect on blast furnace performance. REDUCING APPARATUS The four kinds of reducing apparatus used in this investigation were the following: 1. The JIS* (Modified Gakushin&apos;) apparatus shown in Fig. la is most commonly used in Japan to evaluate the reducibility of ores under static conditions. It consists of a stainless steel tube of 60 mm inside diam suspended from a balance. 2. Linder&apos;s Reduction Test apparatus (Fig. lc) has a reducing barrel 130 mm diam and 200 mm long which rotates at 30 rpm. Some modifications were made in test procedures. 3. Gakushin Standard Test apparatus for determining the reducibility of granular ores (Fig. Id) consists of a horizontal silica tube 32 mm diam, 370 mm long and a movable electric furnace which enables rapid heating and cooling of the specimens. 4. The test apparatus for reduction under load (Fig. lb) gives a comprehensive evaluation of the behavior of ores under conditions simulating the static loading and the chemical reduction conditions encountered in. a blast furnace stack. A stainless steel tube of 50 mm diam and a carbon rod of 35 mm diam were used as the sample container and the support for the weight, respectively. In each investigation care was taken to select the most suitable method and apparatus to distinguish the abnormal nature of the ore in question. SIZE DEGRADATION OF SINTER DURING REDUCTION Sinter makes up the major portion of the blast furnace burden and its behavior during reduction should bear a close relationship to the iron productivity. Recently, some of the sinter was found to show serious size degradation during reduction at a relatively low temperature range. Because this phenomenon was thought to be a possible source of furnace irregularities, tests were made to clarify the phenom-

Jan 1, 1969

By J. H. Nead, J. W. Halley

The new low-alloy high-strength steels are obviously here to stay. With 75 per cent higher yield strength and 50 per cent higher tensile strength than plain carbon structural steel, they permit 20 to 40 per cent weight savings and 10 per cent or more increase in pay load in the construction of railroad cars, buses, trucks, and a great variety of material-handling equipment. Their cost is low enough so that the extra cost of the new lighter construction over that with carbon steel offers an attractive self-liquidating investment; in some instances new construction with these low-alloy steels may even be as cheap as with plain carbon steel. A considerable and rapidly growing demand for the low-alloy steels has already sprung up. The many steel compositions that have appeared on the market lately18, 27, 28, 29, 30 to meet this demand would seem to indicate that no single composition is uniquely fitted for the purpose. However, no doubt some compositions are more suitable than others. The purpose of this study was, therefore, to compare the effects of the various alloying elements that might be used in the low-alloy steels in order to choose the metallurgically most logical composition, paying due regard, of course, to the economic aspects involved. Properties Desired in Low-alloy Steel A distinction between the new low-alloy steels and the common alloy steels is that the latter are generally used in the heat-treated (that is, quenched and tempered) conditions, whereas the new low-alloy steels are not only not heat-treated but are not susceptible to heat-treatment in the ordinary sense of the term. In this lies one of their chief advantages. Their properties can be obtained in the as-rolled, air-cooled, or annealed condition, just as with mild plain carbon structural steel. There is no need for heat-treating. Such steels can be readily formed hot or cold, and their properties are not appreciably changed by hot

Jan 1, 1936

By C. W. Macgregor

The observation of the flow layers, or Luders&apos; lines, produced in mild steel when it is stressed into the plastic range often provides considerable useful information for the study of the fundamental mechanism of the plastic flow of metals. It is a commonly observed fact that as soon as the upper yield point in a mild-st&apos;eel tensile-test bar is passed, an unstable condition develops in the equilibrium, the load on the testing machine drops and if the surface of the bar contains a thin mill scale, the latter begins to flake off rapidly along certain "lines." These "lines" are ill reality traces of wedge-shaped flow layers and are formed by the inter-section of the surface of slip and the surface of the bar. The average plane of the flow layer itself has been found by various experimenters to be inclined at an angle of approximately 45" to the axis of the test bar. In a body of more complicated shape stressed in possibly a different man-ncr, the tangent planes to the flow layers at each point seem in many cases to be inclined at an angle of about 45" to the principal stress direct-tions at the point. As examples of the latter may be mentionecl the logarithmic spirals obtained when a rivet hole is punched in a thin plate, or when a tube is subject,ed to internal pressure only, etc. IIencc if the flow layers are observed from an experiment, the shear-st&apos;ress trajectories —the curves indicating the direct,ions of the maximum shearing stresses in the body—may then be approximately determined. Since the latter curves form an orthogonal family inclined at 45" to the principal stress directions, the family of principal stress trajectories, or the curves irldicating the directions of the principal stresses, may be thus obtained Although the discontinuous type of stress-strain curve at the yield point is commonly observed with test bars of mild steel, more recent experiments have shown that this is by no means the only material exhibiting this interesting phenomenon. A similar effect has been observed in zinc and cadmium crystals, by Becker and Orowai~; in duralumin and other aluminum alloys, by Dawidenkow,~Elam,~ Fell4 an(l others; in copper and copper-alloy crystals, by Elam;~ in brass by Elam;3 in brass wires by deForest;" in higher carbon steels, tungsten steel, and

Jan 1, 1939

By R. E. Somers

1. INTRODUCTION 1. Location, Topography, and Climate The Burro Mountains are located in the southwestern part of New Mexico, in Grant County. The group is made up of two distinct moun-tain masses, known as the Little Burros and the Big Burros, the former lying about 6 miles southwest of Silver City-, and the latter about 9 miles farther in the same direction. They are separated by the valley of the Mangas River, a tributary of the Gila, and a stream only in name, except after a heavy down-pour of rain. . The Little Burros attain an elevation of 6,625 ft. above sea level, and the Big Burros 8,054 ft., with the surrounding country averaging about 6,000 ft. To the south of these mountains stretches the desert plain, while to the north are the more frequent elevations of the mountainous country.

Jan 5, 1915

By J. Chipman, N. J. Grant, H. L. Bishop, H. N. Lander

Data of several studies on the equilibrium between molten iron and open hearth-type slags have been combined to determine some of the chemical reactions involved in steel-making. Effects of slag composition and temperature on the iron oxide activity, distribution of sulfur between slag and metal, and the carbon content of the metal are discussed. Also, an overall reaction for the equilibrium between sulfur and oxygen is presented. DURING the past 15 years, a number of significant equilibrium studies have been carried out between liquid iron and simple basic and acid slags in an effort to throw light on the chemical reactions involved in steelmaking. This paper is a summary of the experimental reports on investigations which have been conducted at the Massachusetts Institute of Technology, and of related work in other laboratories. The investigations summarized in this paper include the works of Fetters and Chipman1 and Taylor and Chipman,&apos; which dealt with simple slags that are similar to those found in the open hearth. The sulfur determinations of the slag-metal tests of Fetters and Chipman as reported by Grant and Chip-man" are included. Also, the investigations by Win-kler and Chipman&apos; and Grant and ChipmanQ f more complex slag systems are included in this summary. The experimental procedure is described in detail in each of these papers and will not be discussed. Since the previous reports have been somewhat independent, it is desirable to review and combine the data of the various investigations to determine, as accurately as possible, the reactions in the slag-metal systems of the open hearth. It is the object of this report to present the combined data in such a way as to enhance their utility and applicability. Oxidizing Power of Slags of the System (CaO+MgO)-Si0,-FeO in Equilibrium with Carbon-Free lron The slags selected to determine the iron oxide activity in equilibrium with pure liquid iron were those containing less than 2 pct each of P,O,, MnO, or A1,0, on a weight percentage basis. The method used to calculate activities of iron oxide in liquid slags was that developed by Taylor and Chipman.&apos; The solubility of oxygen in molten carbon-free iron under pure iron oxide slags can be expressed by the following eauation —6320 log (pctO)-------------— + 2.734 [1] where T is the absolute temperature. The oxygen solubility values as determined from Eq. 1 were used throughout this study to calculate the iron oxide activity. The iron oxide activities of slags of various iron oxide contents are plotted in Fig. 1 as a function of the basicity, which is defined as the ratio (pct CaO + pct MgO)/pct SiO,, and are based on molecular percentage values of the components. The percent (FeO), is the total iron content in the slag calculated to FeO. Fig. 1 shows that as the basicity increases at constant mol pct (FeO),, the iron oxide activity increases rapidly and reaches a plateau which extends on the basicity scale from about 1.3 to 2.3; the iron oxide activity then decreases rapidly until a basicity of about 3.0 is reached, where it tends to level off. The solid portions of the curves represent the experimental data of Fetters and Chipman and Win-kler and Chipman. Their experimental heats were made in magnesia crucibles, and hence the slags were saturated with magnesia. The broken lines on the left represent the experimental data of Taylor and Chipman, who used a rotating crucible. In general, these slags contained less than 3 pct MgO. The absence of data for slags containing less than about 40 mol pct (FeO), and basicity ratios greater than about 2.5 made it necessary to calculate curves using ionic concepts of slags. The broken lines on the right, which disregard the solubility limits of di and tricalcium silicate and lime, were obtained by following the treatment of Flood and Grjotheim,"

Jan 1, 1957

By C. F. Gates, H. J. Ramey

Recent literature shows that pronounced increases in oil recovery can result from the use of miscible systems in recovery operations. This literature also points out certain problems associated with maintaining miscibility, e.g., compositional changes resulting from alterations in pressure and temperature or from zone dilution. The purpose of the work described in this paper was to study miscible zones for possible use in waterflooding operations and examine the manner in which these zones break down. The fluid system selected for study was oil—terNary-butyl alcohol—water, which, because of its narrow range of miscibility, is ideally suited for investigation in short, linear systems. The laboratory-observed effects on oil recovery and zone stability of a number of variables are reported. Among the variables investigated were miscible zone size, viscosity ratio, length of travel, and interstitial water saturation. Results obtained with this system show that interstitial water adversely affects recoveries because of premature phase break. Salinity of the water further aggravates Ais situation. This effect, although pronounced for this system, would probably occur in any fluid system containing an alcohol. As expected, viscosity ratio has a decided influence on recovery efficiency and zone stability. The results also show that use of a suficieno zone size, even though the system has poor phase characteristics, yields higher oil recoveries than are obtained from straight water floods. Length-of-travel studies showed a square root relationship between zone growth and path length for favorable viscosity ratios. No such clear-cut dependence was observed under unfavorable viscosity conditions. INTRODUCTION As new oil reserves have become increasingly more difficult and expensive to find and develop, the oil industry has devoted more and more time and money to finding more efficient methods for exploiting known reserves. The increasing number of water floods is one manifestation of this attempt to improve oil recoveries from existing fields. Since considerable quantities of oil are by-passed by the waterflood process, it is only a partial answer to the problem. The search continues. Of late, several proposed processes have received the critical attention of investigators. Among them are gas drives, in situ thermal reactions and miscible displacements. The present paper is concerned with miscible displacements in conjunction with water floods. Recent literature1- reports that, under proper conditions, oil recoveries from LPG floods, propane sweeps, condensing gas drives, etc., approach 100 per cent of the oil in place in the region contacted by the flood. This literature also points out some of the problems associated with these processes, one of the main ones being the maintaining of miscibility. Compositional changes resulting from pressure and temperature variations or from zone dilution give rise to phase breaks and loss of miscibility, the conclusion being that, after loss of miscibility, much of the beneficial influence of the zone is lost.&apos; The results of the subject work show that, if sufficient zone material exists ahead of a phase interface, considerable improvement in oil recovery can be obtained. In order to increase our understanding of the behavior of miscible systems as they degenerate into immiscible processes, a laboratory system having rapid deterioration characteristics was needed. The fluid system oil—ter tiary-butyl alcohol (TBA)—water possesses these properties and was the system investigated. Although these fluids are different from those generally employed in miscible studies, an understanding of their behavior can be applied to other miscible slug processes. However, under conditions where mass transfer maintains a miscible system through multiple contacts, e.g., enriched gas drive or high pressure gas drive, the observed behavior of alcohol zones would not be applicable. The variables of interest were zone size, viscosity ratio, length of travel, initial water saturation, rate and core characteristics. Of these, only the effects of the following on zone breakdown and oil recovery are reported in detail: (1) zone size, (2) path length, and (3) initial water saturation. The effects of viscosity ratio and core characteristics are discussed in conjunction with other variables. Although initial water saturation is not envisioned as important to the phase behavior of hydrocarbon systems, e.g., LPG, it is important in alcohol systems. The properties of the fluids and cores used are given in Table 1. As previously stated, this fluid system was selected because of the limited range of miscibility

By A. C. Heath, E. H. Dix

The importance of aluminum-silicon alloys in thc light alloy field is now generally recognized. Where silicon was once considered detrimental to the properties of aluminum, useful alloys now contain as much as 13 per cent. Furthermore, silicon is present as an impurity in aluminum of even the purest grades. Iron is another important impurity in aluminum and likc silicon is found in small quantities in the purest aluminum available today. The manner of occurrence of iron and silicon in commercially pure aluminum and many of its alloys exerts a very pronounced influence upon their properties. The effect of large quantities of iron in aluminum-silicon alloys is so detrimental that it has been found necessary to limit the allowable maximum percentage to as low a figure as is consistent with quantity production and satisfactory physical properties. The intimate relation existing between iron and silicon in aluminurn and alurninum alloys makes necessary a more complete knowledge of this ternary system. This paper is divided into two principal parts, dealing respectively with aluminum-silicon solubility equilibria and the constitution of aluminum-iron-silicon alloys. Part I.—Aluminum-silicon Alloys The early work on this system was largely confined to determining the general form of thc diagram and in this respect the results are in good agreement. Briefly, alulninunl and silicon form a simple eutectifcrous series without compounds. Until recently the solid solubility of silicon in aluminum had not been accurately determined. Ipraenkell (1908) stated that aluminum will retain 0.5 per cent. silicon in solid solu-t&apos;ion. Rosenhain, Archbutt and Hanson2 gave the maximum solubility as about 1.50 per cent. and added that "this solubility docs not appear