Search Documents

By H. H. Hasler

THE mining and removal of coal from two or more beds, either simultaneously or consecutively, in vertically adjacent areas have always been matters of concern to mine operators from both operating and recovery points of view. However, with the progressive introduction and use of electrical and mechanical facilities, such problems assume even greater proportions. In this paper typical cases occuring in Cambia County, Pa., are given and procedures whereby such problems may be greatly reduced, if not entirely eliminated, are suggested.

Jan 5, 1951

BOSTON LOCAL SECTION Executive Committee HENRY L. SMYTH, Chairman ALFRED C. LANE, Vice-Chairman AUGUSTUS H. EUSTIS, Secretary-Treasurer, 131 State St., Boston, Mass. ROBERT H. RICHARDS ALBERT SAUVEUR Meets on the first Monday evening of each winter month Twenty-first Meeting The Twenty-first meeting of the Boston. Local Section of the Institute was held at the Engineers' Club, 2 Comonwealth Avenue, Boston, Monday evening, Oct. 5, 1914. Twenty members and two guests were present. The Chairman, Henry L. Smyth, presided at the dinner, at the close of which he introduced, as the speaker of the evening, John M. Longyear, who gave a most interesting talk about his work in exploring for coal on the islands of Spitzbergen, 400 miles north of the North Cape of Norway. The talk was illustrated with many photographs, which showed clearly the nature of the work and the extraordinary difficulties of the location. AUGUSTUS H. EUSTIS, Secretary.

Jan 12, 1914

By C. L. Sollenberger, R. B. Greenwalt

PERHAPS the most widely used dispersants or gangue depressants in nonmetallic flotation are sodium silicates, which vary in silica-to-soda ratio from 1 to 3.75. Typical manufactured silicates in order of decreasing solubility and increasing amounts of silica are Metso, silica-to-soda ratio of 1.00; D, 2.00; RU, 2.40; K, 2.90; N, 3.22; and S-35, 3.75.* References in flotation literature's to the use of sodium silicates are often weak because they fail to mention the type of silicate used. Metso and silicate N have occasionally been mentioned, but when the type of silicate is not mentioned, it is usually assumed to be N, the cheapest of the soluble silicates and the one recommended by sodium silicate manufacturers as a flotation agent.

Jan 6, 1958

By J. W. Goss, M. J. Coolbaugh

A survey of literature published in the U.S. on grouting indicates that most such work has been done to stop water flow in mines and for stabilizing foundations of various man-made structures. Apparently San Manuel is one of the first mines in this country to use grout extensively underground for the strengthening and stabilizing of ground about drifts, shafts, and stations.

Jan 3, 1961

By Paul Levin

A coal preparation plant built with conventional materials only might be able to do an efficient job of preparing coal, but its maintenance costs would be high and emergency shutdowns frequent. To remedy this situation special materials are being used, either in original plant construction or for replacement of conventional materials. The special materials vary from high-strength and abrasion-resisting steels and stainless steel alloys to ceramics. They include hard surfacing welding rods, rubber refractories and some of the newer plastics, the merits of which are cited by the author. A coal preparation plant, limited strictly to the use of conventional materials-for example, mild steel, cast iron and ordinary rubber-could, no doubt, do an efficient job of preparing coal, but the high cost of maintenance and increasingly frequent emergency outages would soon force the operator to seek relief by introducing special materials such as alloyed steels, oil-resistant rubbers and hard-surfacing welding rods.

Jan 6, 1964

By T. Cuscino, D. D. Lane, C. Cowherd, T. E. Baxter

Three types of commercially-available dust suppressants, commonly used in the surface mining industry to control fugitive particulate emissions from unpaved roads, were tested in the laboratory for cohesive strength and resistance to reduced effectiveness by large water addi¬tions. Results indicate that each product tested varies in cohesive strength with a range of 34-300 kPa (5-44 psi). Total cohesive strength depends on the aggregate moisture content and the means by which the sample is dried. Results show that laboratory testing can be used as a decision¬making tool concerning the type of dust suppressant for a particular mining operation. Also, the road surface aggre¬gate moisture content u critical to successful dust suppres¬sant performance. Large water additions to the aggregate road surface after initial suppressant application can pro¬duce nondesirable results. A modified wet sieving analysis is presented to test the effect of water addition.

Jan 1, 1984

By J. R. Johnson

ZIRCONIUM'S corrosion rate by reactor fuel solutions increases with increasing reactor power. It is believed that the protective oxide film is affected by radiation damage. Observations of the

Jan 1, 1959

By Robert S. Shoemaker

Recently we read a short article which stated that Marcona Corp. was studying the use of 25,000-hp autogenous grinding mills for an iron ore project in Alaska. As if that weren't enough, they were going to dispense with the primary crusher and feed run-of-mine ore to the grinding mills which were to be driven by wrap-around seven-cycle motors. We see also that Bougainville Copper Co. will be grinding 90,000 tpd of ore in only eight 4250- hp ball mills. At Bougainville too, their float section will be the first large one to be completely equipped with the new 350-cu ft flotation cells. After a half century of relatively peaceful growth in the minerals industry, we are now seeing almost exponential advances in both equipment and plant size. At the same time, we are seeing a constant blending of hydro and pyrometallurgical techniques and processes into minerals beneficiation until the sample grind-'em-up-and-concentrate-'em plant is becoming a rarity.

Jan 1, 1970

By J. H. Swartz

During 1938 and 1939, an extensive series of geophysical surveys, employing both resistivity and magnetic methods, have been carried on in the Hawaiian Islands by the Section of Geophysics of the United States Geological Survey in cooperation with the Division of Ground-Water of the Survey and the Division of Hydrography of the Territorial Government (see Fig. 1). During this time, surveys have been conducted on the islands of Oahu, Molokai, and Maui. Two distinct types of ground-water occurrence are being investigated: (1) The basal fresh-water lens floating on underlying salt water in obedience to the Ghyben-Herzberg principle (Fig. 2); and (2) perched ground-water (Fig. 3).

Jan 1, 1940

By Chi-shing Wang

Recently the U.S. Bureau of Mines has undertaken a research project to develop the mechanical roof pulling technique as a method for evaluating the effectiveness and the comparative advantages and disadvantages of various roof bolting systems for underground coal mines, based on the characteristic responses of bolted mine roofs to a prescribed external loading system. Two preliminary experiments of the test method were conducted in the Bureau's Safety Research Coal Mine (SRCM) at Bruceton, Pa., and further trials are underway. The fundamental concept of the test method, the design of test rigs, and the experimental results are summarized in this progress report.

Jan 1, 1976

By W. L. Fourney

This paper describes a number of model tests conducted in Plexiglas models to investigate the phenomenon of fracture pressurization. The models were examined with high speed photography while being subjected to explosive loading. At the same time pressure transducers were used to record the pressure in the borehole as a function of time and also along the path of the propagating fracture to measure the pressure at various locations along the fracture as a function of time. Both propellants and explosives were used to charge the borehole. Air as well as fluid filled boreholes were needed to provide a variety of pressure rise rates. On some tests eddy current displacement gauges measured crack opening displacements as a function of time. As a final check high speed photographs taken during the event were used to visually ascertain the location of the fracture at any given time.

Jan 1, 1984

By Robert B. Hill

A history of gravity classification shows the development of many types of equipment with several prominent types continuing in use today. Part of the development and evolution is the spiral classifier. Data will be presented showing characteristic size separations in a closed circuit grinding operation. Comparisons with hydro- cyclone operation will be shown including operating cost comparisons. Effects of variables will be shown in spiral classifier operation. Finally, other uses for spiral classifiers will be described.

Jan 1, 1982

MINING; SOLUTION U.S. 4,066,297 - In the solution mining of uranium from an underground deposit of uranium ore using an alkaline leaching solution, precipitation of alkali metal salts is avoided by maintaining the Injected leach solution of an alkaline carbonate or bicarbonate and an oxidant undersaturated with respect to carbonates Undersaturation is effected by use of a water softening unit or by bleeding a portion of the recycled alkallne leach solution. A P. Spence, assigned to Atlantic Richfield Co Jan. 3, 1978 4 pp. (299-4). Filed: 6-1-76 (69 1,344)

Jan 1, 1979

By William G. Pariseau

The extraction ratio approach to pillar design in flat seams is based on a mathematically exact analysis that is a reasonable physical approximation to room-and-pillar layouts in many instances. The essentials of the approach are reviewed and then mathematically approximate formulas for pillar design in inclined seams of arbitrary dip are proposed. Detailed numerical analysis of stress about a typical 5 entry, 4 pillar panel at dips of 0, 15, 30, 45, 60, 75 and 90 degrees at low and high extraction ratios show that the proposed inclined seam extraction ratio formulas for pillar normal and shear stresses, although conservative, have an accuracy quite adequate for engineering purposes. Appropriate pillar safety factors for compressive and shear failure and a safety criterion for overturning are specified.

Jan 1, 1982

By Rodney P. Smith

The solubility of niobium carbide in y iron has been determined for the temperature range 1000" to 1300°C from the carbon content of a series of Fe-Nb alloys equilibrated with hydrogen-methane mixtures. The method is similar to that used by Darken, Smith, and Filer 1 to determine the solubility of aluminum nitride in y iron and by smith2 to determine the solubility of niobium nitride in y iron. The samples* were strips 1.2 by 3 by 0.035 cm. The niobium oxide.* For samples of composition slightly

Jan 1, 1967

By Miroslaw Hajdasinski

Estimation of the economic effectiveness of industrial development projects including mining ones is generally made on the basis of the discrete model of the value changes in time, although the character of these changes is similar to the continuous model. In this paper an attempt has been undertaken to investigate the problem of the value equivalence of both models exemplified by a construction of an underground coal mine. An effort has been made to determine the errors which for different estimation criteria appear in result of the application of the discrete model. Theoretical considerations have been supplemented with practical conclusions.

Jan 1, 1977

All the TECHNICAL PUBLICATIONS and CONTRIBUTIONS published in 1935 are available at Institute headquarters, unless otherwise noted. They are also on file in many public, university and technical libraries and, when so indicated in the list, may be found in the TRANSACTIONS. Copies of the TECHNICAL PUBLICATIONS have been mailed to members of the Institute that are registered in the different classes: A-Metal Mining; B-Milling and Concentration; C-Iron and Steel Division; D-Nonferrous Metallurgy; E-Institute of Metals Division; F-Coal Division; G-Petroleum Division; H-Industrial Minerals Division (Nonmetallics); I-Mining Geology; J-Mineral Industry Education Division; K-Mining Administration; I-Geophysical Prospecting. Other members may obtain copies by writing to the Secretary. Copies of CONTRIBUTIONS may also be obtained from the Secretary's office. Additional copies are sold at the rate of 1 cent per page; minimum charge, 25 cents. Nonmembers may purchase the papers at the prices mentioned. [ ]

Jan 1, 1936

By George T. Bator

If confronted with the problem of pumping a mixture of slime-free sand, gravel and boulders up to six in. in diameter, at the rate of 175 tons per hr in one single-stage pump against a static head of 90 ft and a total head of 140 ft, of which 20 is on the suction side, an engineer might be forgiven for backing away from the job, especially if he were also told that the pump wearing parts must have a minimum hardness of 550 Brine11 for the sake of abrasion resistance. Yet precisely that feat has been accomplished in the gravel pit of John B. LaGarde, Inc., near Anniston, Ala. The pump used is of decidedly novel design and its successful operation since installation 1.5 years ago suggests that it may be of timely interest in numerous other applications in the mining industry, such as pump transportation of coal washer refuse or rock from open-pit's without unduly fine crushing.

Jan 9, 1950

By John T. Grasso

This paper describes the computer-assisted development and implementation of new written examinations for persons desiring to become certified as underground or surface mine electricians in the State of West Virginia under the certification program defined by the WV Department of Mines and the Board of Miner Training, Education and Certification. The procedures used to develop and validate the new certification tests have simplified the administration of the new tests. Future developments in mine electrical work can also be easily incorporated into the certification program by augmenting the existing computerized pool of test questions prior to computer-production of future test forms. Most important, computerization now facilitates continual evaluation of the certification program, to contribute to greater safety in mine electrical work in West Virginia.

Jan 1, 1983

By W. C. Meyer, R. R. Klimpel

A physical model of flotation, derived from viewing froth as a kinetic species since it constitutes the carrier of ore particles, not only agrees with and is simulated by engineering mathematical models, but is statistically verified by actual laboratory flotation data. The model couples the mechanical removal of froth using paddles with the more rapid interactions taking place in the bath. It clearly shows that the kinetics of mass removal is dictated by flotation cell dimensions, paddle speed, and, more importantly, froth characteristics. Some conclusions and model predictions are presented.

Jan 1, 1984