Search Documents

By O. P. Arora, M. Metzger

Single-phase aluminum containing 1 to 600ppm copper was studied in 7 to 26 pct HCl. The corrosion rate in the autocatalytic stage was resolved into a constant intrinsic component and an acdelerating autocatalytic component, and attention was focused on the part of this stage where the corrosion rate could be described by a simple empirical relation. Autocatalytic corrosion in this period was localized and its rate increased rapidly with copper content and with the strength and chlaride content of the acid. The effects of adding cupric ion to 16 pct HCI were functionally and quantitatively inconsistent with the autocatalytic rates observed. A theory of these rates was given based on the deposition in nzetallic contact with the aluminum of part of the copper introduced by corrosion. It has long been known in a general way that aluminum containing sufficient copper suffers in hydrochloric acid an autocatalytic acceleration of corrosion resulting from the introduction into the acid of copper ions and their reduction on the specimen as elemental copper, which provides cathodes of low hydrogen overvoltage.'-3 In a previous paper, this phenomenon was identified in single-phase high-purity material at copper levels as low as 20 ppm and an empirical equation describing autocatalytic corrosion rates in 16 and 20 pct HC1 was presented. In the present work the range of acid strength and chemistry studied was extended, a more accurate empirical equation for the autocatalytic rate was determined, and a theory of this rate was formulated. A major source of interest in this system is the intergranular corrosion, which is also strongly influenced by copper content,= and an objective of the present work on general corrosion was to provide a basis for studying the role of copper content in intergranular corrosion, which is experimentally much less accessible.

Jan 1, 1963

By Robert G. Woolery, S. Ramachandran, James A. Weber, Donald J. Hansen

Union Carbide began looking seriously at heap leaching in 1971. At that time some 1.6 million tons of mineral averaging 0.40 kg U308 /t) (0.80 lb U308) were stockpiled at various sites around the Gas Hills, Wyoming, uranium facility. Several alternatives for economically exploiting these reserves were considered and heap leaching seemed the most attractive. At the time, Western Nuclear Inc. was operating a heap leaching project nearby in which the low-grade ore was leached with sulfuric acid, the product liquor treated in an on site solvent extraction circuit, and the stripped product liquor re-acidified and recycled. The operators were most generous in allowing us to visit their site and in answering our questions. They were also helpful in discussing the problems associated with heap leaching. Their experience confirmed our belief that it was possible to operate a heap leach profitably on material too low grade for conventional milling.

Jan 3, 1978

By Robert Livermore

IT has been a noteworthy feature of the Cobalt camp, that many of the valuable ore deposits have been covered, wholly or in part, by small but usually deep lakes, such as Cobalt, Cart, and Peterson lakes, and with the subject of this article, Kerr lake. In the early days of the camp many water-covered areas, which have since been found to be valuable, were ignored, or neglected by owners, or simply perfunctorily staked for water rights. Kerr lake is probably the evidence of a fault or sharp fold, having a general east and west strike, and containing a series of ore-bearing fissures, parallel generally to the strike, although having some notable exceptions to the general rule. On the north side of Kerr lake the formation is of diabase, while on the south side it is of Huronian slates and conglomerates. These Huronian measures extend out under the lake, dipping gently to the north to a lateral distance not yet definitely determined, owing to the lack of development under the deepest parts of the lake. Probably the contact between the diabase and Huronian or else between the former and the .underlying Keewatin formation occurs somewhere near the center of the lake. Kerr lake originally covered 45 acres. Of this the Kerr Lake Mining Co. owned 12, the Drummond Mine, 7, and the Crown Reserve Mining Co. the remainder of 26 acres. Since the latter's property was originally entirely under water, it was necessary for the owners to make land for buildings and shaft room. Accordingly, in 1908, a trench was blasted out which deepened the outlet, and lowered the lake 8 ft. As many of the rich veins of the Crown Reserve and Kerr Lake companies were under water, mining was pursued under some disadvantages. Fortunately the rock is tight and solid, and mining has been done sufficiently far from the surface to avoid unnecessary risk. Nevertheless, there was always danger of encountering open seams, through which too large a flow of water for comfortable working might come. Careful soundings were made over the veins, y means of steel-shod pipe, through mud and water to bedrock, but there was sometimes an element of uncertainty as to whether actual bedrock had been reached. Furthermore, the necessity of leaving safe backs between workings and lake tied up large quantities -of-ore, -and- made development- in certain

Jan 7, 1914

By T. A. Read, H. K. Birnbaum

Deformation of AuCd alloys having the 8 (orthorhombic) and (3" (tetragonal) structures occurs by the stress induced motion of twin boutdaries. A restoring force acts on displaced twin boutdaries as a result of internal energy increases in the volume through which the boundaries are displaced. The phenomonology of the twin boundary motion is described and a mechanism for twin boundary motion and the restoring force is proposed. A time-dependent stabilization behavior of the twin boundaries, which is observed after the twins are formed by the diffusionless phase transformations, is described. THE AuCd 8 phase (ordered bcc structure) exhibits a transformation to a phase having an orthorhombic structure, 8' (space group D'), for compositions in the vicinity of 47.5 at. pct Cd and to a phase having a tetragonal structure, 8" (point group 4/m, m,m), for compositions in the vicinity 50.0 at. pct Cd. Both transformations are diffusionless, occur on cooling at 60" and 30OC, respectively, and are crystallo-graphically reversible.' They are accompanied by an inhomogeneous deformation which was observed to be twinning in the low-temperature phase. 3'4 The transformations may occur by a "single interface" or by "multiple interfaces."5'6 In the "single interface" transformation, the twinned product phase consisted of two twin orientations as shown in Fig. 1. In the multiple interface transformation the product phase contained "domains" each of which contained two twin orientations, Fig. 2. Deformation of specimens containing transformation twins was achieved by motion of the twin boundaries. Releasing the applied stress resulted in the displaced twin boundaries returning towards their initial positions. This "pseudo-elastic" behavior of the boundaries varied with time after the formation of the twin boundaries by the transformation.

Jan 1, 1961

By Kidd, Robert L.

INASMUCH as galena and sphalerite flotation concentrates are being produced that contain over 95 per cent galena or sphalerite, it is not unreasonable to believe that a flotation concentrate assaying at least 80 per cent of native gold can he secured provided the gold is free. As yet, little if any fundamental information has been published concerning the flotation of free gold either alone or in the presence of sulfides. So far, we are unable to make as complete a separation of gold from sulfide minerals by flotation as is possible in, the separation of one sulfide from another by this method. An introductory study of the flotation of several free gold ores has been made in our Utah laboratories. For this study three general types of gold ores were chosen, namely: (1) Quartzite containing 0.26 oz. gold per ton in which no base metals are present; (2) sulfide ore (2.04 oz. Au; 1.31 oz. AO containing pyrite as the only sulfide present and the gold free; and (3) oxidized ore (1.10 oz. Au; 0.70 oz. Ag) from an oxidized zone of the vein from which sulfide ore (No. 2) was taken; little sulfide iron was present.

Jan 1, 1932

Jan 1, 1930

Eight members of the Board, the Secretary of the Institute, and eleven guests were present. Vice-president Henry S. Drinker presided. The President was authorized to appoint delegates to a meeting, on May 16, of the League to Enforce Peace. The Joint Conference Committee reported that the American Institute of Metals had accepted the invitation to form the Institute of Metals Division of this Institute. The Committee on Publications of the Institute of Metals was added to the Committee on Publications of the A. I. M. E. Exchange of one volume of Transactions of the A. I. M. E. at reduced price to members of the British Institute of Metals was authorized, in return for the reduced price given to our Institute of Metals Division on the annual proceedings of the British Institute.

Jan 6, 1918

By JAMES GAYLE

(Presented at the Washington meeting, May 3, 1905, and simultaneously sent to the Iron and Steel Institute, for presentation at the meeting of that Society in London, May 11, 1905.) IT is to be regretted that the data respecting the use of dry-air blast, which was presented to the Iron and Steel Institute at its meeting in the United States, in October, 1904, should. have been restricted to the period from August 25th to September 9th inclusive, and from September 17th to 30th inclusive. In order to present the paper at all it was found necessary to limit the record of operations to the period above stated. In the discussion of the paper it would appear from the conclusions of some participating therein, that they have been placed at some disadvantage in considering the economies obtained through the use of dry-air blast, by reason of the data covering such a short period. It is the purpose of this communication to present in detail the record of operations of the Isabella Furnaces from November, 1904, to March, 1905, inclusive, as shown by the furnace-records. The month of October, 1904, is not included, as the furnace using dry-air blast was stopped several times for repairs, and while the record was a very good one considering these interruptions, yet it was not a continuous one. The record for Furnace No. 1 using dry-air blast, and the comparison with Furnace No. 3 using natural air for the month of November, 1904, is set forth in Table I. By a reference to my former paper it will be noted that the month of November is the beginning in this country of the winter period, when the atmosphere decreases rapidly in humidity. The month of October being the transition month in the autumn and April in the spring, and furnaces using natural air approach more closely, from November on, to the conditions obtained by the use of dry-air blast. The data given in

Jul 1, 1905

By C. O. Lee, R. H. Feierabend, Z. W. Bartlett

DESPITE the fact that American brimstone production has increased 2 times since the prewar period 1935-1939, the demand for sulphur exceeds the supply. To alleviate this situation efforts are being made to increase the production of sulphur and bring the shortage to an end. The most important developments are being undertaken on the Gulf Coast. One new brimstone mine has been put into operation and three others are being developed. These projects are expected to account for a large part of the additional sulphur production now anticipated for the free world.'.' Except for a small amount of byproduct sulphur from sour natural gas and refinery gases, American brimstone is produced by the same process devised by Frasch 60 years ago, consisting essentially of the injection of superheated water at about 325°F into sulphur-bearing formations through wells which are drilled from the surface by standard oilfield methods. Sulphur deposits vary in depth from a few hundred feet to 2500 ft from the surface; in a typical deposit the sulphur occurs as crystalline aggregates in porous limestone and gypsum in concentrations varying from 5 to 40 pct, the thickness of the formation ranging from a few feet to several hundred.3 The deposits are usually surrounded by formations impermeable to the flow of hot water, the top and sides being enclosed by impermeable sediments and the bottom by dense impermeable anhydrite. As the hot water leaves the well bore, it percolates through the formation and transmits its heat to the rock and sulphur. When the sulphur reaches 240°F it melts, separates from the rock, and flows through the hot channels downward to the bottom of the well. Here it is freed from incoming water and from formation water, which saturates the porous rock, by gravity separation, liquid sulphur being 1.8 times as heavy as water. It then is pumped to the surface in a relatively pure state, 99.5 pct or better. Chief contaminants are organic impurities, such as petroleum residues, which are soluble in sulphur and tend to discolor it.' Sixteen deposits of commercial magnitude have been discovered in the Gulf Coast area. Five of these deposits have been depleted and abandoned with production totalling more than 26,886,000 tons. Eight properties are operating and have produced 65,875,-000 tons to Jan. 1, 1952, for a total Frasch-type production of 92,761,000 tons. Three new deposits are under development. Aforementioned deposits are listed in Table I. Each of these deposits has been found in the cap-rock overlying shallow intrusive salt plugs or domes and buried in several hundred to as much as 2500 ft of sediments. All salt domes do .not contain sulphur; only 16 sulphur deposits have been found in a total of 231 salt domes which are known to exist in the Gulf Coastal states of Texas, Louisiana, Mississippi, and Alabama. Ten of the salt domes lie in the Gulf of Mexico offshore from the Texas and Louisiana coasts. Additional offshore domes may be found, but their value as a sulphur potential is questionable owing to the great hazard and high cost that can be visualized at these exposed locations where depths of water reach 50 ft. Marsh operations of Freeport Sulphur Co. are in the southeast section of Louisiana. In general, the country is low, flat, relatively uninhabited marshland broken by many shallow lakes and bayous which extend for irregular distances inland. Geologically, the coastal area is of sedimentary origin, having been built up gradually under the sea by deposition of material carried down by large streams to their deltas. Offshore bars were formed enclosing

Jan 1, 1953

By C. O. Lee, Z. W. Bartlett, R. H. Feierabend

DESPITE the fact that American brimstone production has increased 2 times since the prewar period 1935-1939, the demand for sulphur exceeds the supply. To alleviate this situation efforts are being made to increase the production of sulphur and bring the shortage to an end. The most important developments are being undertaken on the Gulf Coast. One new brimstone mine has been put into operation and three others are being developed. These projects are expected to account for a large part of the additional sulphur production now anticipated for the free world.'.' Except for a small amount of byproduct sulphur from sour natural gas and refinery gases, American brimstone is produced by the same process devised by Frasch 60 years ago, consisting essentially of the injection of superheated water at about 325°F into sulphur-bearing formations through wells which are drilled from the surface by standard oilfield methods. Sulphur deposits vary in depth from a few hundred feet to 2500 ft from the surface; in a typical deposit the sulphur occurs as crystalline aggregates in porous limestone and gypsum in concentrations varying from 5 to 40 pct, the thickness of the formation ranging from a few feet to several hundred.3 The deposits are usually surrounded by formations impermeable to the flow of hot water, the top and sides being enclosed by impermeable sediments and the bottom by dense impermeable anhydrite. As the hot water leaves the well bore, it percolates through the formation and transmits its heat to the rock and sulphur. When the sulphur reaches 240°F it melts, separates from the rock, and flows through the hot channels downward to the bottom of the well. Here it is freed from incoming water and from formation water, which saturates the porous rock, by gravity separation, liquid sulphur being 1.8 times as heavy as water. It then is pumped to the surface in a relatively pure state, 99.5 pct or better. Chief contaminants are organic impurities, such as petroleum residues, which are soluble in sulphur and tend to discolor it.' Sixteen deposits of commercial magnitude have been discovered in the Gulf Coast area. Five of these deposits have been depleted and abandoned with production totalling more than 26,886,000 tons. Eight properties are operating and have produced 65,875,-000 tons to Jan. 1, 1952, for a total Frasch-type production of 92,761,000 tons. Three new deposits are under development. Aforementioned deposits are listed in Table I. Each of these deposits has been found in the cap-rock overlying shallow intrusive salt plugs or domes and buried in several hundred to as much as 2500 ft of sediments. All salt domes do .not contain sulphur; only 16 sulphur deposits have been found in a total of 231 salt domes which are known to exist in the Gulf Coastal states of Texas, Louisiana, Mississippi, and Alabama. Ten of the salt domes lie in the Gulf of Mexico offshore from the Texas and Louisiana coasts. Additional offshore domes may be found, but their value as a sulphur potential is questionable owing to the great hazard and high cost that can be visualized at these exposed locations where depths of water reach 50 ft. Marsh operations of Freeport Sulphur Co. are in the southeast section of Louisiana. In general, the country is low, flat, relatively uninhabited marshland broken by many shallow lakes and bayous which extend for irregular distances inland. Geologically, the coastal area is of sedimentary origin, having been built up gradually under the sea by deposition of material carried down by large streams to their deltas. Offshore bars were formed enclosing

Jan 1, 1953

By C. Dinis da Gama

In order to reduce the complexity of mechanisms influencing rock. fragmentation by blasting a simulation approach is proposed, using the capabilities of microcomputer interactive graphics. Situations involving cratering end bench blasting are simulated, and both jointed and intact rocks can be subjected to explosive action, taking into consideration its breakage mechanisms. Size analysis curves relating rock distribution before and after the blasts are determined and compared with field data.

Jan 1, 1984

By C. H. Page, Brenne

Theoretical modelling of a proposed sub-level open stoping mining system was carried out to assess pillar instability and potential for hanging wall caving. This modelling was done, at first, without detailed information concerning the rock mass structure and classification. After mining commenced, the deviance in behaviour from that predicted by the modelling indicated that the structure was having an appreciable modifying effect on behaviour. Further analysis was carried out with detailed engineering geological information and a recently developed pillar design method. The outlined procedure produced results for pillar size and strength that explained the behaviour that had been recorded.

Jan 1, 1983

By R. V. Ramani, C. J. Bise

The potential of deep-mineable coal reserves in the western United States for meeting future energy needs has been recognized for quite some time. However, two of the major constraints tending to limit the development of these underground reserves are the great thicknesses of the coal seams encountered and their high pitch. Although new mining methods may need to be developed to recover these reserves, at least in the short-term the industry has to incorporate presently available equipment not originally designed for thick-seam mining. The purpose of this paper is to present an analysis of the various equipment in use today and their possible application to thick-seam mining. The paper also addresses various ground control and safety considerations unique to thick-seam extraction.

Jan 1, 1984

Welfare endeavor in connection with both the metal and the coal mines of Utah has shown gratifying progress during recent years and both the operators and their employees are deserving of much credit for the efforts put forth to better living, working, educational and receational conditions in most of the mining camps of the state. In the older metal mining camps of Utah, where the towns are incorporated and independent of the mining properties operating in the vicinity, less opportunity is presented for the companies to exercise efforts looking towards improved welfare conditions than is the case of camps located on company ground and under the full control of operators.

Jan 1, 1925

By D. L. Katz

The Oklahoma City Wilcox sand, discovered on March 26, 1930, has produced 394 million barrels of crude oil and 819 billion cubic feet of natural gas as of July I, 1941. The 100,000-bbl. wells, pressures of 2600 lb. per sq. in., and flows of "Wilcox" sand caused exciting moments in the early life of the field. Today the reservoir is substantially at atmospheric pressure and produccs 75,000 bbl. of crude oil daily through 466 pumping wells. Early estimates of the initial crude-oil content of the "Wilcox" sand1 indicated that about 600 million barrels of crude oil would remain after the pumping wells ceased to produce economically. The Oklahoma City Wilcox Secondary Recovery Association was organized in March 1939, to study the possibilities of recovering a portion of this oil. Only a very brief summary of the information available can be presented in a paper of this nature. Some simplifications and generalizations are necessary to give the over-all picture in SO short a space and statements made may not apply to a specific well or small area. Since the area under consideration by the Association is that north of the south line of section 22-11-3, some information will be presented for areas A, B, C, 1, 2, 3 and part of 4 of Fig. 2, and some will be for the entire Wilcox zone west of the fault. This paper is essentially an abstract of an engineering report made by A. D. Small, B. T. Murphree, M. C. Sons and the author for the Oklahoma City Wilcox Secondary Recovery Association on Sept. 5, 1940. Some information is taken from a report to the Association by C. V. Sidwell on March I, 1940, and some data are from a recent report by A. D. Small. It gives a brief history of the Wilcox zone, estimates of the initial oil contents of the reservoir, present conditions in the reservoir, and probable results from several programs of "secondary recovery." History of Wilcox Zone The Wilcox sand lies on the flank of the general structure, as shown by cross section of Fig. I2,3,4 and areal map of Fig. 2. The sand is of Ordovician age and is composed of well assorted, rounded sand grains with no apparent cementing material. The loose texture of the sand is shown by the enormous quantities of sand production from the wells and from the soft cores. The productive sand varies from zero thickness on the east to 220 ft. maximum and to zero thickness on the west because of water. The development of the pool4 as dependent upon drilling restrictions within the city limits, which accounts for the spacing of drilling operations listed in Table I by years. In 1931, areas I through 7 of Fig. 2 were open for drilling with the exception of some west-edge properties, and all wells drilled before Feb. I, 1935, were in this portion of the field. Nearly all wells drilled from 1933 to 1037 were in areas A, B and C. Since 1939, the newly drilled wells have gradually enlarged the producing area toward the west in the northern portion.

Jan 1, 1942

By D. L. Katz

The Oklahoma City Wilcox sand, discovered on March 26, 1930, has produced 394 million barrels of crude oil and 819 billion cubic feet of natural gas as of July I, 1941. The 100,000-bbl. wells, pressures of 2600 lb. per sq. in., and flows of "Wilcox" sand caused exciting moments in the early life of the field. Today the reservoir is substantially at atmospheric pressure and produccs 75,000 bbl. of crude oil daily through 466 pumping wells. Early estimates of the initial crude-oil content of the "Wilcox" sand1 indicated that about 600 million barrels of crude oil would remain after the pumping wells ceased to produce economically. The Oklahoma City Wilcox Secondary Recovery Association was organized in March 1939, to study the possibilities of recovering a portion of this oil. Only a very brief summary of the information available can be presented in a paper of this nature. Some simplifications and generalizations are necessary to give the over-all picture in SO short a space and statements made may not apply to a specific well or small area. Since the area under consideration by the Association is that north of the south line of section 22-11-3, some information will be presented for areas A, B, C, 1, 2, 3 and part of 4 of Fig. 2, and some will be for the entire Wilcox zone west of the fault. This paper is essentially an abstract of an engineering report made by A. D. Small, B. T. Murphree, M. C. Sons and the author for the Oklahoma City Wilcox Secondary Recovery Association on Sept. 5, 1940. Some information is taken from a report to the Association by C. V. Sidwell on March I, 1940, and some data are from a recent report by A. D. Small. It gives a brief history of the Wilcox zone, estimates of the initial oil contents of the reservoir, present conditions in the reservoir, and probable results from several programs of "secondary recovery." History of Wilcox Zone The Wilcox sand lies on the flank of the general structure, as shown by cross section of Fig. I2,3,4 and areal map of Fig. 2. The sand is of Ordovician age and is composed of well assorted, rounded sand grains with no apparent cementing material. The loose texture of the sand is shown by the enormous quantities of sand production from the wells and from the soft cores. The productive sand varies from zero thickness on the east to 220 ft. maximum and to zero thickness on the west because of water. The development of the pool4 as dependent upon drilling restrictions within the city limits, which accounts for the spacing of drilling operations listed in Table I by years. In 1931, areas I through 7 of Fig. 2 were open for drilling with the exception of some west-edge properties, and all wells drilled before Feb. I, 1935, were in this portion of the field. Nearly all wells drilled from 1933 to 1037 were in areas A, B and C. Since 1939, the newly drilled wells have gradually enlarged the producing area toward the west in the northern portion.

Jan 1, 1942

By James B. Cathcart

The potash mine of the International Minerals and Chemical Corp. is about 18 miles east of Carlsbad, New Mexico, in sec 1 and 12, T 22 S, R 29 E, N.M.P.M. Potash is produced from two zones in the Salado formation of late Permian age. The lower zone, consisting of a mixture of sylvite (KCI) and halite (NaCl), lies at a depth of about 900 ft, and the upper zone, in which the principal potassium mineral is langbeinite (K2SO4 2MgSO4), lies at a depth of about 800 ft. Because of the plastic nature of the material, fractures in the Salado formation are extremely rare and have been noted only on the 800 ft level of the International mine. The open fracture described below is almost unique. Only one other open fracture has been noted, and it was on a working face in the same general area as the one described, but was destroyed before the writer had a chance to examine it. According to J. E. Tong, foreman on the 800 level, this fracture was similar to, but smaller than, the one herein described. The saline strata are nearly flat-lying and comprise interbedded layers of halite, anhydrite (CaSO4), and poly-halite (2CaSO4.MgS04.K2SO4-2H2O), with halite predominating. The halite layers contain local concentrations of sylvite, carnallite (KC1.MgCl2.6H2O), and langbeinite. The principal marker in the potash mines area is a bed of anhydrite about 8 ft thick, and 70 ft below the 800 level. This bed contains varying amounts of polyhalite, and locally a few blebs of sylvite. Two principal marker beds are present over most of the 800 level. The lower is the "Middle Salt Marker," a bed of bright-orange halite, which ranges in thickness from a knife-edge to about 0.6 ft, and is usually bounded above and below by thin seams of green or reddish-brown clay. In langbeinite-rich areas, this marker usually contains abundant blebs of langbeinite. The upper of the two principal markers is a green clay seam, containing abundant halite, which ranges in thickness from 0.1 to about 0.5 ft. It is 2 to slightly more than 5 ft above the Middle Salt Marker. No langbeinite of minable grade is found above this clay, and it

Jan 1, 1950

By P. W. Bridgman

DURING the war, the Navy undertook the construction, under my direction, of an experimental gun embodying features designed to lessen the cost and time of production. These experiments were initiated after representations as to their, desirability had been offered by myself, by the Naval Consulting Board, and by the National Research Council. The first drawings were made in June, 1917, and the experiment was completed in November, 1918. For the sake of clearness it will pay to recapitulate briefly the fundamental idea of gun construction. It is well known that if a hollow cylinder is subjected to internal fluid pressure, the maximum stress occurs in the inside layers, the outer parts carrying much less than their due share of the stress. This inequality of stress is more pronounced the thicker the walls of the cylinder. If such a cylinder is pushed to the elastic limit, failure in elasticity will take place long before the outer layers have reached the limit of their capacity. Economical use of the material would demand, however, that all parts of the cylinder reach the limits of their capacity simultaneously. This may be brought about, at least in cylinders of not too great thickness, by producing in. the inner layers an initial compression, and in the outer layers an initial tension. The effect of internal pressure is at, first to relieve the compression of the inside layers, while increasing the tension of the outside layers. If the initial stresses are properly distributed, all parts of the cylinder will reach their elastic limits simultaneously, thus giving a cylinder of maximum strength for its weight. In gun construction as hitherto practiced, this initial distribution of stress is produced either by winding the inner tube with wire, a common English practice, or by shrinking hoops over the inner tube, which has been the standard American practice. Either process is long and expensive, particularly with the larger guns, 12- or 14-in., which require

Jan 2, 1920

By A. S. Adams

A GLANCE at the list of papers1 that have been published since 1920 on the general subject of flotation suggests the variety of ideas that exist regarding the underlying cause of the phenomenon. Among these ideas, we find several coherent theories, but none that adequately and completely explain the phenomenon. Ralston2 and Bains3 suggested an electrical theory which has to do with the attachment of mineral particles to a bubble by the attraction of unlike electrical charges. This theory has its root in the fact that a bubble of air in pure water is electrified in such a way that the surface is negatively charged while the body of the water is positively charged. This result, which was first discussed by Helmholtz, also obtains when the water contains anything except a high concentration of hydrogen ions, or ions which are trivalent or tetravalent. The theory also holds that the mineral particles have positive charges on their surfaces, and so there is attachment between bubble surface and mineral particles by the old law of electrostatics, which states that unlike charges attract.

Jan 1, 1928

By Koert D. Burnham, John G. Broughton

WOLLASTONITE in Essex County, New York, occurs as a typical contact mineral in a series of rocks metamorphosed by anorthosite. Sole current use is in various types of electric welding fluxes. Its uniform lathlike shape suggests its use as a specialized filler.

Jan 1, 1944