Search Documents

By WILLETT G. MILLERS

GENERAL RECEPTION COMMITTEE.-Willett G. Miller, Chairman; F. G. B. Alan, Hon. Frank Cochrane, Eugene Coste, Thomas W. Gibson, Cyril W. Knight, J. C. Murray, 0. N. Scott, Alan Sullivan, J. B. Tyrrell, J. W. Wells, A. B. Willis. COBALT RECEPTION COMMITTEE.-Arthur A. Cole, Chairman; Will. Ask with, R. W. Brigstocke, Robt. Bryce, Fred Coombs, M. I. Culbert, I. R. Drummond, J. W. Evans, A. Ferland, F. N. Flynn, E. L. Fraleck, S. R. Heakes, Joseph Houston, D. L. Jemmett, I. R. Jones, Major Leckie, Capt. Jack Leckie, R. W. Leonard, W. H. Linney, Alexander Longwell, Frank Loring, Murdock McLeod, John Martin, D. B. Rochester, W. E. Running. COBALT RECEPTION COMMITTEE (Ladies).-Mrs. A. A. Cole, Mrs. A. Edwards, Mrs. R. Jennings, Mrs. S. H. Logan, Mrs. A. Longwell, Mrs. H. F. Marsh, Mrs. J. Smith. SUDBURY LOCAL COMMITTEE.-Mayor L. O'Connor, Chairman; S. Fournier, Secretary; A. H. Beath, W. J. Bell, F. B. Bennett, D. M. Brodie, J. S. Buchanan, F. C. Busby, Wm. Chalmers, R. Dorsett, W. A. Evans, John Frawley, J. S. Gill, A. B. Gordon, J. G. Henry, T. N. Kilpatrick, Major Leckie, Chas. McCrea, John McLeod, Wm. McVittie, R. Martin, R. S. Mitchell, J. H. Morin, J. A. Orr, James Purvis (President Board of Trade), C. R. Reid, Major Smith, W. W. Stull, J. F. Templeton, S. E. Wright. The first session, held in the Banquet Hall of the King Edward Hotel, was called to order Tuesday, July 23, 1907, at 2.30 p.m., President John Hays Hammond presiding. Prof. Willett G. Miller, chairman of the General Committee, introduced Alderman J. J. Graham, who, in behalf of the City of Toronto, extended a hearty welcome to the members and guests of the Institute. To this welcome, President Hammond replied in a few well-chosen and hearty remarks. In the hall in which the session was held there was exhibited a fine, full-length, life-size portrait of Dr. Rossiter W. Raymond, in 1871 Vice-President and acting President, in 1872, 1873 and 1874 the elected President, in 1876 and 1877 Vice-President, in 1883, by appointment of the Council, and for the last 24 years by annual election, Secretary, of the Institute. Dr. James Douglas, of New York, N. Y., on behalf of numer-

Sep 1, 1907

By L. S. Darken, H. A. Wriedt

An investigation has been made of nitrogen absorption by the lattice defects in a low-carbon steel afte~ Plastic deformation. Specimens in which defects were distributed by various combinations of cold rolling and vacuum heat treatment were equilibrated with controlled ammonia + hydrogen mixtures at 300° to 450°C to study the relation between the solubility and the thermodynamic activity of nitrogen. The results are interpreted in terms of nitrogen being absorbed upon two different types of defect sites, called A sites and B sites. The concentrations of these sites are calculated for specimens with various histories of straining and annealing; and the thermodynamic relations descrihing the equilibrium distribution of nitrogen among the A, B, and ordinary interstitial sites in ferrite are evaluated as follows: THE generalization that the solute atoms in a solid solution interact with imperfections in the solvent lattice is now universally recognized and the subject of an extensive literature. All types of imperfections—point, line, or surface—exhibit these interactions, but the relative importance of each type depends upon its concentration, the strength of its interaction with the particular solute atom, and whether the interaction is attractive or repulsive. The strength and sign of the interaction vary with the vectorial displacement of the solute atom from the imperfection in the crystal. The concentration of lattice defects increases during plastic deformation and the effect of the imperfections upon the solute atoms is usually perceived only after cold work or irradiation. Two experimental methods have previously been used to observe the effects of interaction between nitrogen atoms and lattice imperfections in a iron. Internal friction, which was first used for this purpose by Dijkstra,1 has been applied more often than the electrical-resistivity method of Cottrell and Churchman.2 The method of the present investigation has not been used before.* Uniform specimens of steel with a metastable defect structure are produced by cold rolling and subsequent heat treatment below the recrystallization temperature. Variations in the defect structure are obtained by varying the amount of strain and the heat-treatment conditions. The specimens are then saturated with nitrogen at moderately elevated temperatures in ammonia + hydrogen mixtures having various thermodynamic activities of nitrogen below saturation with Fe4N. From the nitrogen contents of analyzed samples, the metastable equilibria of interactions between the defects and nitrogen can be established and the concentration of sites for nitrogen atoms in the lattice defects calculated. A steel was used in the present experiments instead of purified iron or iron alloys because the amount of nitrogen absorbed at defects is larger in the steel over a much wider range of experimental conditions and could therefore be measured more accurately. The effect of alloy composition is discussed in Part II of this paper; it is sufficient to say here that impurities and phase heterogeneity in ferritic alloys favor the generation and/or retention of larger defect concentrations during plastic deformation and annealing at 300° to 500°C. MATERIALS AND EXPERIMENTAL PROCEDURE The experimental specimens were prepared from stock of a low-carbon steel, which will be called "X steel" here, with the composition: C, 0.12 pct; Mn, 0.43 pct; P, 0.010 pct; S, 0.034 pct; Si, 0.007 pct; As, 0.086 pct; Cu, 0.022 pct; Ni, 0.009 pct; Cr, 0.003 pct. The stock was all from a single ingot made by the basic open-hearth process, which was hot-rolled to strip 0.080 in. thick.. This hot-rolled strip, given the code designation "XH", was the starting material for preparing a series of cold-rolled sheets. The latter are designated "XC27",

Jan 1, 1965

By George M. Fowler, J. P. LYDEN

T HE relationship of geological structure to orebodies and to the great masses of chert in the Tri-State mining district is of such significance that it prompts a brief recital of the existing information regarding the various periods of structural deformation. We began to note a relationship between structure and orebodies early in our studies of the field, and further work revealed a like relationship of structure to the great masses of chert so commonly associated with the ore-

Jan 1, 1934

By W. J. Romanow

RECENT papers by Williams, Sherwood, and Boothby,1 Seybolt et al.2 Heikes; and Roberts4 attest to the increasing importance of the hexagonal ferromagnetic compound MnBi. Since the magnetic properties of MnBi crystals are highly anisotropic, it is useful and necessary to have appropriate aids for determining their orientations—a (00.1) standard stereographic projection and a corresponding table of crystallographic angles for this structure. The tables of crystallographic angles for the hexagonal system available in the literature5 are computed for c/a ratios greater than that of MnBi and cannot satisfactorily be used to find the crystallographic angles of MnBi. A table of angles between the crystallographic planes (HK.L) and (hk.1) was calculated for MnBi from the formula0 F=are cos Hh+Kk+ 1/2(Hk+hK) + 3/4 (a/c)2Ll/v(H2 + K2 + HK + 3/4 (a/c)2L2) (h2+ k2+hk + 3/4 (a/c)2l2) on an IBM Type 650 Magnetic Drum Data Processing machine. The lattice constants used are listed in Table I and are those determined by Willis and Rooksby7 at 20°C. More recently published values obtained by both X-ray and neutron diffraction"' show no difference from these significant to the calculation. From the crystallographic angles between the basal plane (00.1) and the general plane (hk.1) in Table I, an (00.1) standard stereographic projection was made for MnBi which is shown in Fig. 1. Acknowledgments The author wishes to thank R. G. Treuting and J. N. Hobstetter for their technical assistance, and Miss D. P. Booth for programing the IBM machine for the calculations. He appreciates the opportunity to read the paper of B. W. Roberts of General Electric Co. prior to its publication. References 1H. J. Williams, R. C. Sherwood, and 0. L. Boothby: Bulletin Amer. Physical Soc., 1956 vol. 1, p. 132. 2 A. U. Seybolt, H. Hangen, B. W. Roberts, and P. Yurcisin: AIME Trans., 1956, vol. 206, p. 605: Journal oF Metals, May 1956. 3R. R. Heikes: Physical Review, 1955, vol. 99, p. 446. .B. W. Roberts: A Neutron Diffraction Study of the Structures of Manganese B.W.Roberts:ANeutronDiffractionBismuthide, Physical. Review, 1956, vol. 104, p. 607. 5 A. Taylor and S. Leber: AIME Trans., 1954, vol. 200, p. 190; JouRNal of Metals February 1954. « C. S. Barrett: Structure of Metals, 2nd Ed., p. 635. McGraw-Hill Book Co. New York and London, 1952. 7B. T. M. Willis and H. P. Rooksby: Proceedings Physical Soc., London, 1954, vol. 67B, p. 290.

Jan 1, 1958

By Joseph J. Yancik, Leonard L. Felts, George B. Clark

LITTLE information has been published concerning the actual or useful amount of energy obtained from explosives when they are used for blasting. To provide more data on this subject, 8-in. neet cement cubes were blasted in a steel plate box and the breakage energy evaluated by comparison with drop crusher results using Rittinger's,1,2 Kick's: and Bond's' theories. Theories by Bond and Wang," Lineau," Hatch,' Roller,' and others0-11 were not considered applicable. Those used in this investigation may be expressed mathematically as follows: Rittinger Theory E = KrS2, pet,—--------------- [1] 40 d1 d0 Kick Theory TV 1 1 E = =K, [S pct. log1/d+ 100 log d0] [2] 40 d1 L. L. FELTS, Junior Member AIME, was formerly a Graduate Assistant, University of Illinois. G. B. CLARK, Member AIME, was formerly Professor of Mining Engineering, University of Illinois, and is now Chairman, Dept. of Mining Engineering, Missouri School of Mines and Metallurgy. J. YANCIK, Junior Member AIME, is a Graduate Assistant, Missouri School of Mines and Metallurgy. This paper, TP 4213A. is revised from a thesis submitted by L. L. Felts in partial fulfillment of the M.S. degree in Mining Engineering, University of Illinois, 1954. Discussion may be sent (2 copies) to AIME before May 31, 1956. Manuscript, Dec. 27, 1954. Bond's Third Theory E = Kb [S pct. log1/d1+ 100 log d0] where E — energy used in breakage, d, = average diameters of screen fractions of broken cement particles, pct, = percent weight of diameter d;, and 2 pct, = 100 pct. The above equations were employed to determine values of Kr, Kk, Kb for particle size distributions similar to those obtained from the blasting curves. These values were in turn used as a means of approximating the specific energy of the blasted material. The efficiency of crushing by blasting was then determined by dividing this specific energy by the maximum available work of the explosive per gram of cement. Knowledge of the failure of solids under static loads is developing very rapidly. Their failure under impact loads has been investigated and reported in the literature only to a limited extent. Theories of failure' hnder static loading include 1) the maximum stress theory, 2) the maximum strain theory, 3) the theory of constant elastic strain, 4) theory of maximum shearing stress, and 5) Mohr's theory of strength. All of these have elements of usefulness in establishing an applicable theory for blasting. For highly strained and compressed material such as that surrounding a detonating charge of high explosive, the Mohr theory and its implications appear to be the

Jan 1, 1957

By John V. Beall

BROMO Seltzer blue has gone to war. The blue of the Bromo Seltzer bottle is a product of cobalt, the Nation's No. 1 strategic metal. When the National Production Authority, on Nov. 21, 1950, ordered a 70 pct cutback in domestic use of cobalt, a stab of pain was felt in the hearts of the glass, porcelain enamel, steel, paint, pottery, and electrical and electronic equipment industries. The reason: A full-scale wartime economy with astronomical requirements for jet engines, high velocity projectiles, armor plate, electronic equipment, and the many products needed to win a war. There is little potential comfort for cobalt users in nonessential manufacturing, and the military will be pinched for optimum supplies of the metal. However, if proper measures are taken immediately and current plans are completed, in two years there will be far more cobalt available than ever before. When normal times return, cobalt supplies should be sufficient to meet peacetime military requirements, and greatly expanded domestic requirements that will result from new technological development for wartime but adaptable to peacetime products. The pres-

Jan 1, 1951

By CHARLES DORRANGE

INTRODUCTION. CULM is a general term used in the anthracite regions for many years to denote a mixture of coal, bony coal and impurities which is sent to the refuse-banks. Thus, 35 years ago culm contained the pea and buckwheat sizes of anthracite; but to-day, and as mentioned in this paper, culm is used specifically to denote the material which passes through the smallest screen in the anthracite-breaker. The smallest size of commercial anthracite is known as No. 3 buckwheat, barley, or bird's-eye coal, and is ordinarily made through a round-punched plate having openings 3/16 in. in diameter, and over a round-punched plate with opening 3/32 in. or 1/16 in. in diameter. Thus culm will consist of coal, bony coal, slate, gravel, iron pyrite, etc., ranging in size from ? 3/32 in. down to dust. Other local terms for culm are " slush," " silt," and " dirt." The first experiments towards the utilization of anthracite culm by briquetting, and the first briquetting-work done in this country, were in 1872 at Port Richmond Piers, Philadelphia, Pa., by E. F., Loiseau.1 Clay was used as a binder and the finished briquette was water-proofed with shellac, etc. Excessive cost was given as the reason for discontinuing work at this plant. The Delaware k Hudson Co., in 1876, built a plant at Rondout, N. Y., which operated until 1880. Gas-tar was used as a binder, and anthracite screenings were briquetted for engine fuel. Excessive cost, poor results in firing, and the tendency of the fuel to cut the boiler-flues were given as the reasons for discontinuing the manufacture. The next plant was built by E. F. Loiseau about 1878, at Nesquehoning, Pa., near the No. 1 or Nesquehoning colliery

Sep 1, 1911

By VERITAS

THE most concentrated industry of major character in the United States is that of the Ford Motor CO., which is to say Henry Ford. Its sole function is to supply the public with a cheap motor car which it does to the extent of two million or so per annum. In doing this, a relatively small profit per unit is multi- plied to an enormous aggregate per annum and has resulted in the creation of one of the greatest industrial fortunes of the world. The industrial and sociological consequences of .this are bound to be immense. On the physical side the production of two million automobiles means the consumption of two or three million tons of materials, chiefly metals, in the 'direct form of the finished product', and a huge additional tonnage of coal and other things that ,are consumed en route, and also the labor of many thousands of men. In the development of a business on this scale it was but natural that the Ford Motor ,Co. should seek to supply itself with the raw 'materials it needs, and they being so largely coal and metals the company is brought into close contact with the mining and metallurgical industries. It is a huge consumer of - steel. It is the fourth largest consumer of copper. It is a large consumer of lead, tin, aluminum and zinc. The mining and metallurgical industries have, therefore, good reason to learn to know Henry Ford, his personality, his thoughts and his policies.

Jan 1, 1924

By J. B. Campbell, V. V. Valleroy, B. T. Willman, L. W. Powers

A steam drive of heavy oil was field tested in a shallow, low oil-saturation formation near Deerfield, Mo. The pilot was conducted in the Warner formation, a sandstone containing an 18' API oil having 1,000-cp viscosity at the 60F origind reservoir temperature. The formation war at a depth of 160 ft. Steam was injected into nine input wells arranged in an array of inverted five-spot patterns. In the completely confined center pattern, 14 temperature observation wells were installed to obtain thermal data and observe test progress. Late in the test, slugs of ammonia were injected to trace the flow paths of injected fluids. From the test area about 7,000 bbl of oil were produced. Data were obtained on areal and vertical temperature distribution, steam front advance, reservoir fluid movement and terminal saturations. This field test of a steam drive (I) demonstrated the feasibility of the method, (2) confirmed that the low residual oil saturations observed in the laboratory are obtained in the steam-swept region in the field and (3) provided recovery and conformance data for one set of field conditions. INTRODUCTION The Deerfield steam drive pilot test was conducted in a shallow sandstone containing 1,000-cp oil. The venture was undertaken cooperatively by the research and production departments of Carter Oil Co., which organizations have since been consolidated into Esso Production Research Co. and Humble Oil & Refining Co.. respectively. The production department was interested in steam injection at Deerfield because it appeared to be the most promising method of commercially producing this heavy oil deposit. The research department was interested in applying the new recovery method and in evaluating its performance in the field. At the time the test was begun, the initial oil saturation was not well known. Subsequent air coring and early pilot results confirmed that there was too little oil in place for profitable commercial exploitation by steam. Pilot termination at that time, however, would have been premature for evaluating field performance of the process, and the tert was continued to obtain additional data on steam injection as a recovery method. The test was located in Vernon County, Mo., about 10 miles north of the town of Deerfield and only a few miles from the Kansas border. The pilot site was selected as typical of the area. The location represented neither the highest nor the lowest oil saturation region in the acreage under lease in 1954. The steam drive was conducted in the Warner sandstone of Lower Pennsylvanian age. At the test site the top of the Warner occurs at about 160 ft subsurface and the formation is a fine- to medium-grained micaceous sandstone that dips gently to the northwest at the rate of 12 to 15 ft/ mile. A cross-section and permeability profile of the test location are shown in Fig. 1. At the pilot location the average total thickness of the Warner formation is about 43 ft, but the effective thickness for steam drive is 26 ft. Two distinct types of hydrocarbon saturation are apparent. The lower portion of the total sand, averaging about 17 ft thick, contains a very heavy asphaltic material that will not flow under the influence of a steam drive. This bottom interval, referred to as a dead oil residue, was not considered as part of the net sand undergoing steam exploitation. The initial formation and fluid properties of the upper 26 ft in the test area are summarized in Table 1, and variation of oil viscosity with temperature is shown in Fig. 2. Imbibition tests on preserved core samples taken at the end of the pilot test showed that the Warner sandstone was then neutral or slightly water-wet. Initially, the reservoir may have been strongly water-wet as indicated by low relative permeability to water during both water injection testing and early steam injection. PRIOR HISTORY Initial production tests of wells at the pilot site produced water with only a faint show of oil. No gas was produced except at Well 7-W in the pilot area and at another well about 1/3 mile northeast of the pilot. Prior to the start of the steam drive, a two-well water injection test and a two-well air injection test were conducted. No oil was produced by either. Water was pumped into Well I-W in the northeast corner of the pilot area with simultaneous production from Well 1 (Fig. 3). The air-injection tat was run at input Well 9-W and its offset, Well 2, in the southwest corner. Air and water injectivities were about the same when corrected for viscosity and pressure differences.

By Walter Harvey Weed

Introductory.............449 Summary oF Types............452 I. The Virgilina Type...........452 The Virgilina mines...........452 Location.............452 History.............453 The rocks of the district..........453 The veins.............454 Notes on the mines.... 458 The Holloway. 458; Yancey and Durgy. 465 ; Copper World. 467 ; Frazier. 467 ; Thomas. 467 ; Anaconda. 468; Blue Wing. 468; High Hill. 472; Dorothy.......474 II. The Gold Hill Type...........474 The Gold Hill mine...........475 Location.............475 History............• 475 Surface improvements.......... 476 The rocks............478 Vein.phenomena...........478 Character of the ore..........481 Origin of the ore...........481 Notes on the mine.workings.........482 Other occurrences of ore-deposits of the Gold Hill type.. .. 483 III. The Ducktown Type..........484 The Ducktown mines...........485 Other examples of the Ducktown type....... 494 Alabama mines...........494 North Carolina examples : Ore Knob.......496 Virginia examples..........497 IV. The Catoctin Type.. ......... 498 General characteristics,......... 498 The Linden district...........499 General distribution of the Catoctin type.......503 Introductory. In the early history of this country the existence of copper in the Appalachian region was well known. but no mining mas attempted until the discovery of the Ducktown deposits in

Jan 1, 1901

By Henri S. Swolfs

INTRODUCTION In this paper we present preliminary results of a research program in site characterization methodology. We are interested in under- standing the response of discontinuous rock to mechanical, hydrologic, and thermal loadings. To carry out such a study we selected a field site with simple geology, uniform distribution of lithologies, and easily verifiable boundary conditions on temperature, fluid flow and stresses. The spatial distribution of fractures at the site was established and tests were conducted to determine the temperature field, hydrology, rock-mass properties, and in situ stresses. As part of the study selected borehole instruments were compared to assess their performance and reliability. SITE GEOLOGY The study area is in the eastern part of South Table Mountain, a mesa near Golden, Colo. The exposed cap rock is a single lava flow of uniform thickness (6-7 m) that rests on the clastic sediments of the Denver Formation (Van Horn, 1976). The surface of the cap rock (N. 75º E., 3º S.) is topographically featureless and slopes south- southeast; drainage is predominantly downdip and punctuated by occasional contact springs. The age of the lava flow is 64-65 m.y., or early Paleocene. Paleo- botanic evidence confirms the upper part of the Denver Formation as Paleocene (Van Horn, 1976). "Rapid-rock" analyses of core samples from the lava flow at three depths (0.2, 3.3, and 5.8 m) suggest a uniform chemical composition throughout with an increase in the Fe2O3/ FeO ratio (1.05 to 1.60) with increasing depth, reflecting the existence of a perched water table in the lava flow, To identify the rock

Jan 1, 1984

By Hiram B. Woon

Uranium ore deposits in the Lisbon Valley area are in an arcuate belt, 15 miles long by one-half-mile wide, on the southwest flank of the Lisbon Valley anticline. They range in size from 500 to 1,500,000 tons and by mid-1965 had yielded 6,147,000 tons containing 48,530,000 pounds of U3O8. Ore bodies average 6 feet thick, are tabular, amoeba-shaped masses, concordant to the bedding, and are in the thickest, lowest sandstone unit of the Moss Back Member of the Chinle Formation of Triassic age. The host rock is predominantly a fluviatile, calcareous, fine-grained to conglomeratic sandstone. Uraninite, the principal ore mineral, fills the pores in the sandstone and partly replaces sand grains and fossil wood fragments. During Late Permian and Early Triassic time pre-Chinle Formations were arched to form the ancestral Permian anticline. Moss Back streams truncated Moenkopi and Cutler beds which capped the ancestral anticline and then covered it with fluviatile elastics, which were subsequently covered by thousands of feet of Triassic, Jurassic, and Cretaceous sediments. Uranium, probably derived from the Chinle Formation by diagenetic processes, was transported in connate ground waters, was moved by compaction or hydrostatic forces, and was deposited under reducing conditions. Uranium was emplaced around the crest of the ancestral anticline, prior to the Laramide orogeny. During the orogeny, the Tertiary-Lisbon valley anticline was super induced on the Permian anticline and, penecontemporaneous with uplift, was faulted parallel to its longitudinal axis. The Big Indian ore belt on the southwest flank footwall block was elevated to approximately its present position, and the northeast flank hanging wall block was elevated only slightly. An extension of the Big Indian ore belt around the northeast flank of the ancestral Permian anticline may exist in the Moss Back sandstone in the downthrown block northeast of the Lisbon Valley fault.

Jan 1, 1968

By Reginald E. Hore

I. INTRODUCTION. SINCE the discovery of silver at Cobalt, Ontario, in 1903 more than 100,000,000 oz. of silver have been produced b: the mines in the Nipissing district, and there is reason to believe that at least as much more will be produced in the next five years. The estimated value of the aggregate output o ore to the end of 1910 is $48,327,280. The ore yielded 93,977,833, oz. of silver and was mined at a net profit of about $26,000,000. For 1910 the production was 30,558,825 oz. valued at $15,436,894, and yielding a profit of about $9,000',000 The details of the production of the Cobalt district for the years 1904 to 1909, inclusive, are given in Table I. TABLE I.-Silver-Production of the Cobalt District, 1904 to 1909 SMELTING-ORE. Production. Value. Silver-Content. Value Per Ton Ounces. Oz. Per Ton. 1904 206,875 $111,887 1,309 $708 1905.:.... 2,451,356 1,360,503 1,143 634 1906 5,401,766 3,667,551 1,013 687 1907 10,023,311 6,155,391 677 416 1908 18,022,480 8,468,293 736 363 1909 22,436,355 10,809,872 809 389 CONCENTRATES. 1908 1,415,395 $665,085 1,240 585 1909 3,461,470 1,651,704 1,174 559 The shipments from Cobalt are in the form of smelting-ore, concentrates from milling-ore, and bullion. The smelting-or( is largely high grade, averaging about 3,000 oz. per ton- A

May 1, 1911

By G. T. Jackson

The Alaska Gastineau Mining Co.'s mine is located at Perseverance, about 4 mi. east of Juheau, Alaska. Its property consists of a group of claims, the lode system traversing these claims for a distance of 11,000 ft. (3352 m.). It is shown in Fig. 1. The ore deposits occur in what is known as the Juneau gold belt. This gold belt can be traced for about 50 mi. northwest of Juneau and 40 mi. southeast. It consists of a single band, several hundred feet wide, in which stringers and veins of quartz, carrying gold, occur in a slate formation near its contact with some altered volcanic rock known as greenstone. The Perseverance orebody consists of stringer lodes, having a strike northwest and southeast, dipping about 60° to the northeast. These

Jan 1, 1920

By P. A. Flinn

ALTHOUGH many physical properties of superlat-tices have been studied intensively, relatively little attention has been paid to their mechanical properties until recently. Even for the well-known transformation in 0 brass, the effect of the transformation on plastic behavior has only lately been extensively investigated.''' A partial analysis of dislocation structure in superlattices has been given by cottrel13 and his theory agrees well with the experimental results on CU3AU.4,5 His analysis, however, is implicitly limited to low-temperature effects, since it does not include the behavior of dislocations at temperatures high enough for diffusion, and hence climb, to occur. The work of Herman and Brown2 on the creep of 0 brass indicates that important effects occur under such conditions, and consequently, the theory should be extended to include them. Such high-temperature effects cannot be observed in Cu3Au, since it disorders below the temperature at which diffusion occurs at a reasonable rate. There are materials of the same structure, however, such as Ni3A1, which retain their order up to, or close to, the melting point. GEOMETRY OF THE COMMON SUPERLATTICES The two best-known ordered structures are the 0 brass type, B2, shown in Fig. 1, and the Cu3Au type, Ll2, shown in Fig. 2. In the B2 structure the (000) and (1/2, 1/2, 1/2) sites are different in that they are occupied by different types of atoms. The symmetry of the structure is then lowered from a body-centered cubic, A2, in which the sites are equivalent, with atoms located randomly in the sites, to simple cubic. This lowering of symmetry has the consequence that two types of regions may occur within a crystal: regions where A atoms are in the (0, 0, 0) sites, and regions where they are in (1/2, 1/2, 1/2) sites. The boundary between two such regions will contain bonds between like atoms, and be a surface of higher energy. These regions are known as antiphase domains and the boundary as antiphase boundary. In the B2 structure, boundary formed during the ordering process should disappear as a result of domain growth, since any domain growing to the boundary of two others will join one and engulf the other.' In any well annealed crystal, only a single domain should exist, with antiphase boundary present only in connection with dislocations, as discussed below. The L1, structure is related to the A1 (face-centered cubic) in much the same way as the B2 is to the A2. The face-center sites are occupied by A atoms, and the corner sites by B atoms. The symmetry is again lowered to simple cubic, and antiphase domains can exist. In this case, however, there are four initially equivalent sites in the unit cell: (0,0,0), (0, 1/2, 1/2), (1/2,0, 1/2) and (1/2, 1/2, 0). In the ordered structure any one may be occupied by a B atom and the other three by A atoms. Thus four types of antiphase domains can occur in this structure. This is sufficient to permit a metastable "foam structure" to exist within a crystal.''7 Antiphase boundaries along three different planes are shown in Figs. 3, 4, and 5.* *The presence of a layer of disordered material between antiphase domains, as suggested by Jones and Sykes8 does not seem likely. Such a layer would be a region of unnecessarily high energy which could readily be reduced by the formation of the type of boundary discussed here.__________________________________________________________ The notation (111) [110] means a boundary lying along a (111) plane between antiphase regions related by a 1/2 [I10] translation. It may be seen in Figs. 3 and 4 that an antiphase boundary usually results in incorrect nearest neighbors (shown connected by braces). However, as pointed out by Wilson, a boundary of the (001) [I101 type can exist

Jan 1, 1961

By S. A. Mahon

AN interesting feature among the mining structures, on the Mesabi. iron range is the iron ore stacker erected in 1934 at the Mesabi Chief washing plant at Keewatin, Minn. It is built of structural steel, and carries a system of belt conveyors which collects the washed product of the plant and places it on a stockpile for subsequent shipment. Although the only one of its kind in the Lake Superior iron district, installations of similar nature have been used elsewhere in the handling of coal and gravel and in earthwork construction. The reasons for stocking Lake Superior iron ores may be as various and diversified as the methods used in building the piles. At the under¬ground mines the existence of the huge piles in evidence at each active shaft is due, principally, to climatic conditions in this north country where the shipping period is much shorter than the operating season. Conversely, at the washing. plants it may be desirable to stockpile washed ores because the shipping season is commonly of longer duration than the period during which the plants may be operated. Washed ores, and mixtures of which washed ores are a component part, have found high favor with the oper

Jan 1, 1935

By AIME AIME

REPUBLIC STEEL'S new iron blast furnace in Alabama, shown on the cover of this issue, is the first to be completed of those authorized by the Government last year when a shortage of scrap became acute. In addition to the furnace, the new equipment includes a new battery of by-product coke ovens, a boiler plant, a generating unit, a 3-mile-long 60-in. water line, a huge gas washer, and precipitators in which the dust from the furnace is washed, separated from the water, and fed back into the furnace as raw material. The new unit is a cylindrical steel giant reaching 130 ft. into the air above the ground level. Because of the high humidity in the deep South, the furnace has been air-conditioned to avoid blowing eighteen tons of water into the furnace daily. Designed by Republic engineers who also had charge of the actual construction, the new furnace incorporates the best in modern blastfurnace practice. Orders to proceed with the construction of the furnace were received Sept. 22, 1941. The engineering crew, which was immediately organized, made more than 1500 drawings. Excavation started the next day, and simultaneously work was begun on demolishing existing buildings and preparing the site. The first concrete was poured Oct. 7 and the first piece of steel swung into place by a giant derrick on Jan. 30, 1942. It began operating May 28. A total of 70,000 cu. yd. of earth was moved and 30,000 cu. yd. of concrete poured.

Jan 1, 1942

By NEWTON B. KNOX

IN Bolivia, mining is still the principal economic activity, as it was before and during the Spanish Colonial period. Tin, tungsten, antimony, copper, lead, zinc, gold, silver, sulphur, and a little bismuth are produced. The Andes mountains are divided into two main ranges in Bolivia; the Western range marks the border with Chile and the Eastern range forms the backbone of the country; in the North it drops rather abruptly eastward, to the plains of the Beni, whereas in the South it splits and is separated from the Chaco flatlands by a series of folded mountain ranges. In general the mineral deposits are found within the Eastern range or in the hills that rise from the high plateau between the ranges - really parts of the Eastern range partly submerged by recent sediments. The mineral belt is thus over 500 miles long and about 100 miles wide and includes most of the principal centers of population and the most important means of communication. The region is mountainous and the roads are bad; furthermore labor is a serious problem, for the land is poor and the agricultural population is never far from hunger. The floating supply of miners is limited and soon exhausted in any emergency like the present.

Jan 1, 1945

By J. R. McWilliams

Several of the current concepts of brittle fracture involve consideration of the existence of defects or flaws. Griffith 1 observed that the tensile strength of brittle materials was several orders of magnitude less than might be expected from the calculated strength of the molecular bonds. He was able to show that the stress concentration at the tip of an elliptical crack is sufficient to raise the local stress level many fold. He therefore proposed that real materials do contain such stress risers in the form of minute cracks and that this accounts for the rather large difference between theoretical and actual strengths of brittle materials. The degree of stress magnification depends to a great extent upon the orientation of the crack with respect to the general stress system, and to the general geometry of the crack.

Jan 1, 1967

By Jennings S. Cox

(Glen Summit Meeting, June, 1911.) THE following notes, prepared in 1908, as the result of a personal examination and extensive explorations under my direction in 1906, have been revised and greatly augmented after two subsequent visits and further explorations in 191.0. The hard iron-ores of the south coast of Oriente Province, in the island of Cuba, have been known for many years, in fact one mine has been in operation for more than 20 years ; but it is only within the past four years that the large mantle-deposits of brown ores of the north coast have attracted serious attention. A. C. Spencer 1 has described these ores in a paper, entitled Three Deposits of Iron Ore in Cuba, which refers to the Mayari, Moa, and Cubitas deposits. C. M. Weld,2 in a scholarly paper on The Residual Brown Iron-Ores of Cuba, has discussed the character and possible genesis of these deposits with particular reference to the Moa field, calling attention also to the Taco and Navas fields in addition to those described by Spencer. Descriptive articles with reference to the Mayari field, and a few words about the Moa deposit, have also appeared.3 It is the purpose of the present paper to give some account of the exploration of the Moa deposit and to call attention to its commercial importance. LOCATION. The Moa district is situated on the north coast of the . Province of Oriente, which is the most easterly province of the island of Cuba. It lies on the northern or seaward slope of 1 Bulletin No. 340, U. S. Geological Survey, pp. 318 to 329 (1908). 2 Trans., xl., 299 to 312 (1910). 3 Iron Age, vol. lxxx., No. 7, pp. 421 to 426 (Aug. 15, 1907), and vol. lxxxi., No. 15, pp. 1149 to 1157 (April 9, 1908).

Mar 1, 1911