Search Documents

By R. F. Mehl, C. S. Barrett, A. G. Guy

INTRODUCTION IN the last few years this laboratory has published a series of papers on the mecha¬nism of age -hardening.14,1,6,11,20 Briefly stated it has been proposed that hardening is caused by lattice strains created by lat¬tice coherency between matrix and precipi¬tate; much experimental evidence has been advanced to support this thesis. The system Cu-Be is an attractive one to study. It is a system that exhibits marked age hardening; it ought to be subject to the type of analysis of structural changes hitherto explored and it is a prominent example of "discontinuous precipitation," which, though studied in other cases, 6,20 remains largely unexplained. This research shows that hardening in the Cu-Be system proceeds essentially as proposed earlier.14 Guinier-Preston zones have been observed to form on the {100) planes of the matrix; no transition lattice was found. Aging and overaging were ob¬served to occur most rapidly in the region of discontinuous precipitation-the grain boundary-apparently accelerated there by strain. The Constitution of the Cu-Be System The Cu-Be constitution diagram is shown in Fig I. The structure of the ? phase was determined by Misch16 as of the caesium-chloride type with a lattice con¬stant of 2.598 Å High temperature X ray photograms of 7.2 pct Be alloy made by Kossolapow and Trapesnikow13 led them to conclude that the structure of the P phase is simply disordered body-centered cubic with [ao] = 2.79 Å at 750°C. Previous Work The initial work on the age-hardening of Cu-Be alloys was that of Masing, Dahl, Holm, and Haase. Their numerous papers were published in book form in 1929, sub¬sequently translated.18 The effects of Be content, solution temperature, aging tem¬perature, and cold work on the hardness developed in these alloys were studied. An initial decrease in the electrical conduc¬tivity was observed when strips of a 2.5 pct Be alloy were aged at temperatures from 200 to 350°C; a wire of the same analysis failed to exhibit this decrease when aged at 350°C. A volume decrease of 0.6 pct oc¬curred during aging at 250°C. Microscopic investigations of quenched and aged alloys disclosed a regularly ori¬ented "striping" (ripples) on the a and on the ß grains. In the case of the ß the cause of the striping was held to be decomposition

Jan 1, 1948

By W. M. Weigel

Economic deposits of barite occur in Missouri in two main districts. The most important, the Southeastern or Washington County district, is in the southeastern part of the state, mostly in Washington County with a small extension into the northeastern part of St. Francois County. Roughly, it embraces nine townships or about 200,000 acres and accounts for from 80 to 90 per cent. of the state production. The Central district, is in the central part of the state, includes most of Morgan and Miller counties, and parts of Camden; Benton, Moniteau and Cole counties. The area embraced is much larger than the Washington County district, but the deposits are more infrequent. The location and general area covered by the two districts is shown in Fig. 1. There is another small area in southern Franklin County but so far its production has been of small consequence. It might be considered as a northward extension of the Washington County field. An, area in the central part of Hickory County has also produced a small amount. The outline of the districts as shown indicates the general area in which deposits have been found. The total area covered by deposits of barite is only a small part of this, as, in the Central district especially, there may be miles of supposedly barren areas between ore-bearing areas of an acre or two in extent. The date when barite was first mined in Missouri cannot be definit stated, but the industry probably dates back to about 1860. The occurrence of barite was known long before this, as it was encountered in the lead mines in Washington County and mentioned by several earlier writers." Missouri is reported as producing 8000 tons in 1882 so it is evident the industry was well under way in the seventies in order to have arrived at this substantial production. By 1893 Missouri production had increased so that it ranked with that of Virginia, then the largest producer it increased until in 1914 Missouri accounted for about 65 per cent. of the total United States output.

Jan 1, 1929

By DOOLITTLE E. M.

(Canal Zone Meeting, November, 1910.) The following notes are contributed, not with the idea of offering a complete history of the development of this very important process as applied to the Leadville district, but with the hope that the practice, as it was carried out in the Bi-Metallic Smelter, may still be of interest to others. The Bi-Metallic Smelter, at Leadville, Colo., was the first to make a commercial success of the process described in the following pages, which consisted essentially of smelting raw silver- and copper-bearing sulphide ores in blast-furnaces to form a matte, which was generally re-smelted with siliceous ores for a second high-grade matte. Robert Sticht, in his excellent monograph on the subject,1 has outlined briefly the plant belonging to this company. He says, in effect: The Boulder, Mont., enterprise set the example for others with whom the patentee (w. L. Austin) had been negotiating, and the old La Plata lead-smelter at Leadville, Colo., was fashioned into a crude, temporary experimental plant for the Bi-Metallic Company, and the feasibility of the process demonstrated by a trial run. Subsequently, the plant was considerably improved, and, being supplied with very favorable ores, continued to run without interruption from August, 1892, to June, 1893. In September, 1893, smelting was resumed in a completely remodeled establishment, some $200,000 having been expended upon the new work. Thus, aside from the Montana experiments, which, under the direction of W. L. Austin, began as early as- 1885 2 at Toston, and continued with indifferent success for six or seven years, the Bi-Metallic plant at Leadville may be said to have * Formerly Superintendent, Bi-Metallic Smelting Co. + Formerly Chief Assayer and Chemist, Bi-Metallic Smelting Co. 1 Modern Copper Smelting, E. D. Peters, 7th ed., p. 415 (1895). 2 Trans., xvi., p. 259 (1887-88).

Dec 1, 1910

By L. E. Young

IT has been said the British Empire was built on British Coal. In all the postwar planning for Great Britain the necessity for producing cheap coal and the prosperity of the coal industry are given first consideration. On Jan. 23, 1945, there was released in London a "Report to the Colliery Owners" which had been awaited with great interest. This was entitled "A Plan for Coal" and was the recommendation of Robert Foot, chairman of The Mining Association (Colliery Owners), prepared at their request. Presentation of the "Plan" at this time is particularly significant as it is an answer to the demand for nationalization of the coal industry by the Labour Party and at the same time is a carefully considered program for postwar reconstruction, prosperity, and stability. In the words of Mr. Foot, If the coal industry for the first ten years after this war is to find itself in a situation similar to the one it occupied for the ten years following the last war, with its record of disputes, strikes, stoppages, short-time working, unemployment, and, with it all, a completely insufficient margin of profit, and all the insecurity and instability in our basic industry that was brought with them, it is goodbye to any real prospect of full employment, social security, and high standard of living. To present an elaborate review of the conditions which have brought to a crisis the unfortunate situation in the British coal industry is here unnecessary, but certain of the salient points

Jan 1, 1945

By J. A. Retty

IN the Labrador iron fields two concessions, totaling nearly 24,000 square miles, have been staked out and commercial-grade deposits delineated. The Newfoundland-Labrador concession, owned by the Labrador Mining and Exploration Co. Ltd., is a 20,000-square-mile tract in the upper basins of the Hamilton and N askaupi Rivers which drain into Lake Melville. The New Quebec licensed area is 3900 square miles, owned by the Hollinger North Shore Exploration Co. Ltd., lying to the northwest of the northwestern part of the Labrador concession. It includes the upper basin of the Swampy Bay River and part of the upper basin of the Whale River, both of which drain into Ungava Bay. Both of the above-named companies are controlled by Hollinger Consolidated Gold Mines Ltd. with The M. A. Hanna Co., of Cleveland, holding a minority interest. When exploration was first undertaken in 1936, the only published map of the area was that prepared by A. P. Low in 1895. It showed only the main watercourses and gave only a rough, general idea of the geology. The numerous lakes of this vast area had to be first sketched and then mapped. Since then, extensive geological and topographical surveys have been conducted by the Labrador company, work which is normally done by Government branches. The object of the work was to examine the area and gradually eliminate unfavorable or less favorable prospecting ground. With this object in view, geological

Jan 1, 1948

By Charles S. Barrett

THERE is a road into the microscopic realm that has remained untraveled through all these years of intense activity with high-power optical and electron microscopy. The road is worthy of careful scouting by metallurgists and other investigators, for it leads into relatively new country and it makes some areas accessible that heretofore could be reached only by very indirect paths or by the use of imagination. And when the road passes through familiar territory it frequently permits a new view of commonplace things that should prove of value from time to time. An accepted way to interest people in new sights such as this is to present an illustrated travelogue. This I propose to do, using many pictures taken in my recent exploration of this road. In the manner of travelogues, I shall touch briefly upon a large number of different subjects in physical metallurgy and shall, attempt to give an exhaustive treatment of none, for the objective is to provide a means for further research, to interest others in it, and to indicate what appears at the moment to be profitable directions for it to take. The method I shall present involves X-rays, but does not make use of the usual accompaniments of X-ray research such as reciprocal lattices, Fourier series, or the stereographic projection. The method is so simple in its fundamentals that it could have been developed 20 years ago, or perhaps even 30 years ago. It is well to have a destination for our travels, so that when we are through we shall have explored some region of importance, despite our preoccupation with the novel means of transportation and our interest in the sights to be seen along the way. So let us name the Cold Worked State as our destination, and make side trips into the territories known as Recovery, Recrystallization, and Precipitation-hardening. A great many investigations have been made of the nature of cold-worked metal, and a great variety of methods used, many of which are indirect, such as X-ray line intensities, X-ray line widths, calorimetric measurements, and magnetic measurements. Since comprehensive reviews of these investigations have been published in recent years, they need not be discussed here. The investigations that were the direct forerunners of the present work should be first mentioned. In 1931 I became interested in the structure of individual spots in X-ray diffraction patterns.1 When a crystal is placed in the narrow pencil of X-rays in a Laue camera, the spots recorded on the film are not always uniformly black, but may have an internal structure. The meaning of this may be understood from Fig. 1, which represents a narrow beam containing X-rays of many wave lengths ("general radiation") penetrating a crystal in the direction of the arrow and forming a pattern on the vertical film at the right.

Jan 1, 1945

By Joseph Hyde Pratt, Douglas B. Sterrett, CHAPEL HILL

I. DESCRIPTION. MONAZITE is one of the minerals which, for a long time, was considered rather rare in its occurrence, but, upon a commercial demand arising for it, prospectors and engineers soon located large deposits of it in the Carolinas and Brazil, and the supply has always been able to meet the demand. During 1908 further sources of supply of monazite have been discovered and developed in Idaho. North and South Carolina, however, are the only States that have thus far put any monazite on the market. Monazite is essentially an anhydrous phosphate of the rare-earth metals, cerium, lanthanum, and didymium (Ce, La, Di)PO;. There is nearly always present a varying but small percentage of thoria, ThO2, and silicic acid, SiO, which are very probably united in the form of a thorium silicate, ThSiO4 Some monazites contain but a fraction of a per cent. of thoria, while others have been recorded that showed the presence of from 18 to 32 per cent. ; but the majority contain from 3 to 9 per cent. of this oxide. It is the presence of the thorium oxide that gives the monazite its commercial value. The analysis occasionally shows also the presence of other constituents, as the yttrium and erbium oxides, zirconia, alumina, magnesia, lime, iron oxides, manganese oxide, and titanium oxide. Monazite is light-yellow, honey-yellow, reddish-, brownish-, or greenish-yellow in color, with a resinous to vitreous luster, and is translucent to subtransparent. It is brittle, with a conchoidal to uneven fracture, and is from 5 to 5.5 in hardness, and from 4.64 to 5.3 in specific gravity. It crystallizes in the monoclinic system, and some crystals have been observed that were 6 in. in length. The more perfect crystals are, however,

Jun 1, 1909

Erwin S. SperRy, Bridgeport, Conn.: The analysis of refined copper is a subject of great importance, and has not received the attention it deserves. Copper metallurgists, therefore, will welcome the paper of Mr. Heath with satisfaction. The state of the art of the chemical analysis of copper has been such that consumers, if they could not afford to run any risk, have been obliged to buy copper from the smelter having the best reputation, and a specification for copper to meet certain requirements could not be drawn up by the mere giving of the chemical constituents. Mr. Heath has brought the analysis of the copper to such a state that when a specification calls for copper " equal to Lake copper " one will know immediately what percentage of the pure metal to expect. It seems to be a pretty well established fact that the copper of Lake Superior is practically free from antimony and bitmuth ; and, with the exception of arsenic, the other elements are easily separated from copper by electro-deposition in an acid solution. The authorities differ in regard to the question whether antimony is deposited with the copper in an acid solution. Classen* recommends the employment of a solution containing 10 per cent. of free nitric acid, sp.gr.1.21, and the strength of the current from 0.3 to 0.4 ampere, in order to prevent the other metals from being deposited with the copper; and for this reason, I presume, the method has been generally used. I, myself, have been accustomed to use such a solution for the analysis of copper-alloys, but have found that for such alloys only a small quantity of nitric acid is necessary, if sulphuric acid is present in sufficient amount to give the solution the required conductivity.

Jan 1, 1898

By Wm. A. Haven

ON the northern part of the globe, almost since the earliest days of mankind's history. ironmaking has been practiced in one form or another. Some investigators question the generally accepted belief that copper and bronze were in earlier general use than iron, explaining the greater age and abundance of copper relics by their greater resistance to natural oxidation. However, the occurrence of copper in its natural state and its greater ease of reduction from the simpler copper minerals is a strong argument that the making and use of copper came first. Nevertheless, good evidence exists that ironmaking was practiced in ancient India and China, as well as in ancient European countries. Some interesting vestiges of those early operations still survive and have a place, in the background at least, of a discussion of modern blast-furnace practice.

Jan 1, 1940

By George J. Young

(San Francisco meeting, October, 1911.) THE nature of slimes handled in the treatment of gold- and silver-ores has been discussed in technical literature to a considerable extent. The subject of slime-filtration from the practical worker's stand-point has also received much comment, and scattered through the literature of the subject are descriptions of many slime-filtration installations. Articles of this nature serve a valuable purpose and assist materially in the design of new and the improvement of old plants. The subject of the physics of slime-filtration has been touched upon to only a slight extent. The underlying principles are worthy of more intensive study and experimentation than they have received, and the main purpose of this paper is to present the results of such study and experimental work as will serve to make clear in part at least many of the principles which control the filtration of slime. Nature of Slime. Much has bean written concerning an accurate definition of the term ? slime," but no comprehensive definition seems to be generally accepted. The reason for this is clear. A slime consists of at least three different substances, each, when separated, possessing distinctly different physical and to a certain extent chemical properties. These substances are extremely fine sand, a colloidal material which may be and generally is in a coagulated condition, and a colloidal material which is in a non-coagulated condition. Suspending a slime in a relatively large volume of water by shaking and allowing sedimentation to take place, results in the fine sand settling out with comparative rapidity, followed by the coagulated material, which settles much more slowly and finally a certain portion remains

Nov 1, 1911

By Ian Wark

IN an earlier paper1 measurements of contact angles due to the effect of xanthates on mineral surfaces were reported. The solutions in which these measurements were made differed widely from those of modern flotation circuits. It is intended, however, by introducing, one at a time, the other principal reagents of flotation, to approach gradually the solu-tion composition of flotation liquors. The work now described is an attempt to determine the effect of one of the most important of these reagents-namely, sodium cyanide-on the establishment of air-mineral contact. The work has been carried out for the following companies: Broken Hill South, North Broken Hill, Zinc Corporation, Electro-lytic Zinc of Australasia, Mount Lyell Mining and Railway, and Burma Corporation. Since the effect of cyanide is inseparably connected with the alkalinity, the results cited below deal with the mutual effects of alkalis and cyanide. Alkalis alone exert a significant effect on the air-mineral contact but comparatively large amounts are required. Since the addition of a small amount of cyanide greatly decreases the degree of alkalinity necessary for the suppression of contact at surfaces of any of the minerals experimented with (except galena) and since alkalis are rarely used alone in practice, little attention has been paid to cyanide-free solutions. It was shown in the previous paper that, excluding the dixanthogen effect, whenever contact was practicable at all in an ethyl xanthate solution the angle of contact was 60°. There is, therefore, less necessity to measure equilibrium contact angles; in fact, the experiments herein described have generally been conducted with a view to determining whether contact is possible and not to measuring the actual value of the contact angle. The separations which have generally to be effected in dealing with complex sulfide ores are: (1) galena from sphalerite, pyrite, etc.; (2) sphalerite from pyrite and/or gangue minerals; (3) copper minerals from pyrite and gangue minerals; (4) pyrite from gangue minerals; (5) chal-

Jan 1, 1933

By T. Sterry Hunt

WET processes for the extraction of copper from its ores have of late attracted much attention, especially in Europe, where the use of oupriferous iron-pyrites as a' source of sulphur prevails. These processes present an additional interest, when, as is often the case, the copper-ore's to be treated contain one or both of the precious metals, since the complete separation of these from copper, either in the dry or the moist way, is, as is well known, one of the difficult problems of metallurgy. The principal wet processes hitherto in use for the extraction of copper from its ores, may be included under three classes : I. Those in which the copper in snlphuretted ores is rendered soluble in water by calcining them, after a preliminary roasting which removes the greater part of their sulphur, with a portion of common salt, by which the copper is converted into a chloride (Long-maid and Henderson), or with sulphate of soda, by which sulphate of copper is formed (Monnier). Allied to these is the method by which a portion of the copper is got as soluble sulphate by roasting without addition, a process which is sometimes modified and rendered more complete by re-roasting the lixiviated residues with the addition of a portion of raw sulphuretted ore (Bankart). II. Those methods in which free chlorhydric or sulphuric acid is used to dissolve the copper- from oxidized or roasted ores. These, while simple and efficient, are too costly, except in certain localities where chlorhydric acid is a waste product. Related to them is the plan which consists in exposing the oxidized and moistened ores to the slow action of sulphurous acid mixed with air, by which a soluble sulphate of copper is formed. It has been proposed to decompose the solutions of sulphate or chloride of copper by sulphuretted hydrogen, thus separating the copper as sulphide, and using the liberated acid to dissolve fresh portions of oxidized copper. It is, however, the almost universal practice to throw down the copper from its solutions, however obtained, in the metallic state by the use of iron, either scrap-iron or iron-sponge; although in some instances

Jan 1, 1882

By T. Sterry Hunt

Jan 1, 1882

By P. A. Beck, M. V. Nevitt

All binary and a number of ternary u alloys formed by first long period transition elements were examined and found to be ferromagnetic at low temperatures. The Curie temperatures for these alloys were measured. It was found that the correlation of the Curie temperature with composition may be described qualitatively in terms of the contributions of the various component atomic moments to the saturation moment of the alloy. Ternary Fe-Cr-Mo u phase alloys were also found to be ferromagnetic, with a Curie temperature dependent on the iron content and largely independent of the unit cell dimensions. Similar relations were found for the Co-Fe-Cr and the Co-Cr-Mo a alloys, where the Co + Fe content appears to determine the Curie temperature. RECENTLY, it has become increasingly evident that the u phase is some kind of an "electron compound." Several papers1-' discussed the empirical correlation between the composition of the various u phases in alloys of the transition elements and the distribution of electrons in the partially filled d-levels of the component atoms. However, a picture of the latter can be formed only in a more or less intuitive manner, as in the Pauling theory," and the rigorous treatment of these problems is at present prevented by lack of adequate knowledge of the electronic structure of the transition elements in the metallic state. It appeared reasonable to expect that investigation of the magnetic properties, which are related to d-shell electrons, may help in clarifying the physical nature of the foregoing empirical correlation. Qualitative tests of samples of various compositions have shown that certain u alloys become ferromagnetic at liquid nitrogen temperature." The present investigation was undertaken to determine whether or not low temperature ferromagnetism is characteristic of a large variety of u alloys and to establish how the Curie temperatures of ferromagnetic u alloys are influenced by changes in composition and in lattice parameter. In the first portion of the in- vestigation, Curie temperatures were measured for a series of u alloys containing either vanadium or chromium with one or two of the elements manganese, iron, cobalt, or nickel. In the second phase of the work, data were obtained on the Curie temperature of ternary (Fe, Co, Cr)a, (Fe, Cr, Mo)a, and (Co, Cr, MO)U alloys, as a function of composition and of interatomic spacing. Experimental Procedures High frequency vacuum melting in high purity re-crystallized alumina crucibles was employed in the preparation of the u alloys, using metals whose lot analyses are given in Table I. Approximately two-thirds of the alloys were analyzed chemically, the analytical results being in acceptable agreement with the intended compositions, as seen in Tables I1 and 111. The specimens were annealed for homogen-ization in an atmosphere of purified 92 pct He and 8 pct H, mixture or in evacuated and sealed Vycor tubes at temperatures from 780" to 1300°C, depending on the temperature range of the u phase field for the particular composition. The annealing temwerature and time for kach alloy are given in Tables 11 and 111. Curie points were determined by an induction method; the change with temperature of mutual inductance between two coils was observed when the i-u specimen was inserted into the flux path between the coils. The transformer consisted of three coils each containing 1200 turns of 0.0050 in. diam enameled copper wire. The center coil, P in Fig. 1, served as the primary coil, and was linked magnetically with each of the two secondary coils, S, and S? which were connected in series opposition. The primary coil, P, was energized by an audio-oscillator, set at a frequency of 500 cycles per sec, while the signal from the transformer secondary circuit,

Jan 1, 1956

By Robert B Sosman

The relative temperature distribution within a coke oven and among the ovens in a battery can be obtained automatically for the operator's guidance by sighting a total-radiation pyrometer on the face of the coke as it is pushed out, and recording the surface temperature. Keeping the instrument clean and keeping its view of the coke unobstructed by smoke and dust are the principal problems. Typical records from three plants are presented in this paper, showing that the temperature patterns are reproducible. Development OF Method The method of coke pyrometry described in this paper was introduced in 1936 by E. A. Lee, then Assistant Superintendent, now Superintendent, of the Coke Plant at Lorain Works, National Tube Co., Lorain, Ohio. At the request of the Coke Committee of the United States Steel Corporation, the Research Laboratory of the Corporation undertook to adapt the method to the somewhat different conditions met with at the Gary Works of the Carnegie-Illinois Steel Corporation, Gary, Ind., and at the Clairton Works of the same Corporation at Clairton, Pa. This work was done in cooperation with the Leeds and Northrup Co. of Philadelphia and later with the Brown Instrument Co. Division of Minneapolis-Honeywell Regulator Co., Philadelphia. We of the Research Laboratory wish to express our appreci- ation of the courtesies extended by Mr. Lee, by A. N. Cole, Superintendent of the Gary coke plant, and by D. P. Finney, Assistant General Superintendent in charge of coke-plant operations at Clairton. We are also indebted to the instrument companies for the loan of a part of the equipment. At Gary and Clairton the instruments were installed and various experiments were made by J. W. Bain, of the Research Laboratory of the United States Steel Corporation. Pyrometry of Coke The coke inside a by-product oven is almost completely inaccessible to pyro-metric instruments. The temperature in the walls can conceivably be measured with thermocouples, but the atmosphere is usually strongly reducing, a condition well known to be destructive to the accuracy of the customary high-temperature couples. In some plants, periodic readings are taken with an optical pyrometer sighted into the top of the combustion flues. This is a useful measure for safety and general control, as it tends to prevent the damage that would result from overheating of the ovens. It does not, however, tell much about the temperature of the coke itself, because of the continually changing gradient in the wall between the coke and the combustion chamber. The best indication of the temperature of the coke itself must therefore be obtained by observation of the product as it is pushed out of the oven. The human eye is very sensitive to variations in brightness of a surface, and particularly to differences in brightness over a continuous hot surface.

Jan 1, 1943

By Robert B. Sosman

The relative temperature distribution within a coke oven and among the ovens in a battery can be obtained automatically for the operator's guidance by sighting a total-radiation pyrometer on the face of the coke as it is pushed out, and recording the surface temperature. Keeping the instrument clean and keeping its view of the coke unobstructed by smoke and dust are the principal problems. Typical records from three plants are presented in this paper, showing that the temperature patterns are reproducible. Development OF Method The method of coke pyrometry described in this paper was introduced in 1936 by E. A. Lee, then Assistant Superintendent, now Superintendent, of the Coke Plant at Lorain Works, National Tube Co., Lorain, Ohio. At the request of the Coke Committee of the United States Steel Corporation, the Research Laboratory of the Corporation undertook to adapt the method to the somewhat different conditions met with at the Gary Works of the Carnegie-Illinois Steel Corporation, Gary, Ind., and at the Clairton Works of the same Corporation at Clairton, Pa. This work was done in cooperation with the Leeds and Northrup Co. of Philadelphia and later with the Brown Instrument Co. Division of Minneapolis-Honeywell Regulator Co., Philadelphia. We of the Research Laboratory wish to express our appreci- ation of the courtesies extended by Mr. Lee, by A. N. Cole, Superintendent of the Gary coke plant, and by D. P. Finney, Assistant General Superintendent in charge of coke-plant operations at Clairton. We are also indebted to the instrument companies for the loan of a part of the equipment. At Gary and Clairton the instruments were installed and various experiments were made by J. W. Bain, of the Research Laboratory of the United States Steel Corporation. Pyrometry of Coke The coke inside a by-product oven is almost completely inaccessible to pyro-metric instruments. The temperature in the walls can conceivably be measured with thermocouples, but the atmosphere is usually strongly reducing, a condition well known to be destructive to the accuracy of the customary high-temperature couples. In some plants, periodic readings are taken with an optical pyrometer sighted into the top of the combustion flues. This is a useful measure for safety and general control, as it tends to prevent the damage that would result from overheating of the ovens. It does not, however, tell much about the temperature of the coke itself, because of the continually changing gradient in the wall between the coke and the combustion chamber. The best indication of the temperature of the coke itself must therefore be obtained by observation of the product as it is pushed out of the oven. The human eye is very sensitive to variations in brightness of a surface, and particularly to differences in brightness over a continuous hot surface.

Jan 1, 1943

By Thomas B. Douglas

INSTRUMENTATION in the process industries can no longer be regarded as a convenience, but rather an absolute necessity. Although many chemical processes must already be conducted with instruments, every properly designed application of automatic process control will improve operation: 1) the product will be more uniform and of higher quality; 2) the manual labor saved will reduce cost; 3) uniformity of flow and uniform control of process will increase production; and 4) surges will be eliminated, making it possible to operate equipment near ultimate capacity at all times. Industrial instruments fall into two general classifications-those that measure and those that measure and control. The cement industry has been using instruments for a number of years, particularly in the burning process, primarily for indicating and recording. Automatic process control makes additional use of these instruments, and others, to control variables. Assisted by the instrument manufacturers, engineers at Ideal Cement CO. achieved considerable progress in determining how well the usual recording instruments could be made to control various phases of cement-making. The results of these experiments were used to make the new plant at Houston as wholly automatic as possible.

Jan 2, 1958

ANNUAL meeting of the Woman's Auxiliary of the American Institute of Mining and Metal-lurgical Engineers convened on Tuesday morn-ing, Feb. 20, the president, Mrs. H. W. Hardinge, presiding. President Hardinge, in opening the meet-ing, said: "I have the honor and great pleasure to welcome you to our seventh annual meeting. It has been a happy year, though I started in fear and trembling. My fear is partly gone and my trembling becomes less as time goes on. Never has a chairman had such splendid cooperation and harmony in her work; no. matter how much was asked nor what the task, I have always received the same answer, `We are with you, of course we can do it.' Often the road has been untried and the way full of snares, but we have all pulled together. Is it any wonder we have had a prosperous year? I cannot thank the governing -board and officers enough for their help." Mrs. Hardinge described her trip through the West last summer, during which she visited many of the local sections of the Auxiliary. She also spoke of the work of the Rossiter Raymond memorial library which has been started as an activity of the Woman's Auxiliary. Mrs. Reynders read the minutes of the last annual meeting, and Mrs. Kemp read the treasurer's report. The latter showed that on Feb. 1, 1922, there was a bank balance of $683.61 and on Feb. 10, 1923, the bal-ance was $947.93. Mrs. Westervelt expressed the sorrow of the Auxiliary for the death -of Mrs. Florence Howe Hall and of Mrs. Levi P. Holbrook.

Jan 4, 1923

By Johnson Crawford, Alan H. Hoagland

Zinc mining at Jefferson City began in 1854 with small scale production of oxidized ore from open pits. Significant production began in 1913 with the development of the Mascot Mine by the American Zinc Company. In 1965, four flotation mills were treating crude ore at the rate of about 12,000 tons per day and the Mascot-Jefferson City district currently is the largest zinc producing area in the United States. The producing mines, Mascot, Young, North Friends Station, New Market Zinc, Grasselli, Davis-Bible, Coy, and the Jefferson City, are 15 to 28 miles northeast of Knoxville in the Valley and Ridge physiographic province, an area of gentle relief lying between the more rugged Great Smoky Mountains and the Cumberland escarpment. The ore is strata bound, occurring essentially within a stratigraphic range of 200 feet in the Lower Kingsport and Upper Longview formations of Lower Ordovician age. In the lower strata of the mineralized section, the ore generally is found in coarsely crystalline elastic dolomite breccia containing silica and chert debris within a sequence of aphanitic limestones. The upper strata of the mineralized section are fine-grained primary dolomites that, in the ore zones, have been fragmented in mosaic patterns by solution collapse with the interfragmental space filled by white gangue dolomite and sphalerite. The mineralogy is unusually simple, sphalerite being the only important sulfide. Pyrite is very sparse. Dolomite gangue is abundant, silica was deposited in quite small amounts, calcite is minor, and fluorite and barite are very rare. The principal ore controlling structures are rubble breccia zones that were formed during the post-Lower Ordovician-pre-Middle Ordovician erosion interval by supergene solution as a phase of the development of a regional karst system of underground drainage that extended to' depths of at least 800 feet. The major Appalachian orogenic structures are post-ore and have been superimposed on the ore bodies. There is substantial evidence to support the current thinking of the writers that the ore deposits were formed at a depth not exc1~eding 800 feet.

Jan 1, 1968

By C. M. Brinckerhoff

Safety work in mining at the Andes Copper Mining Company, Potrerillos, Chile, is divided into three parts: (1) accident prevention, (2) fire prevention and protection, and (3) silicosis prevention and control. In the company's operations a steady campaign has been waged to reduce accidents and silicosis, and to prevent fires. In the following pages the safety record for the past twelve years will be examined and the methods explained by which the accident rate was reduced. Table 1 contains yearly data pertaining to the scale of the mining operations and the accident record. Block caving is used for all ore production and the tonnage mined has aver- aged 30,000 short tons per day for the past seven years. Table 2 classifies 44 fatal accidents which have occurred since 1935. The leading causes of accidental death are transportation of ore and use of explosives, followed in order by per- sons falling, falls of ground, and by asphyxiation. In the case of serious accidents, however, the greatest cause is falls of ground, followed, in turn, by ore

Jan 1, 1949