Search Documents

By A. D. Hughes

C. W. MERRILL*-Mr. Hughes' paper not only is very well presented but is most timely in that it covers a subject of vital interest to the United States. Tin is one of the strategic metals which has not been found here in appreciable quantities. The total United States tin output since the first recorded production over 100 years ago would not supply current consumption for a fortnight. On the consumption side, tin is extremely important in national defense because of its use in tin plate which, in the form of tin cans, makes it possible to feed properly the armies that the United States recruits from its civilian population in emergencies. Moreover, the internal combustion engines so important in powering tanks, planes, and other war machines, require large quantities of tin alloys for bearings and for soldering. These considerations, along with the fact that Malaya, historically, has been the leading source of tin to the United States, make the kind of information that Mr. Hughes has presented so ably, a matter of vital interest.

Jan 1, 1949

By J. A. Fellows, Earnshaw Cook, H. S. Avery

THE increased use of heat-resistant alloys (26 per cent Cr, 12 per cent Ni; 16 per cent Cr, 35 per cent Ni; 12 per cent Cr, 60 per cent Ni; etc.) in recent years has been accompanied by continued demands by the consumer for improvement in properties. The manufacturers of these materials, of necessity, have resorted to more critical studies of the basic causes of variations in fundamental properties. To keep pace with the need for augmented information, previous techniques of investigation have been refined and new test methods and instruments created. It is the purpose of this paper to describe the apparatus, experimental technique and precision of measurement that were employed in the exploration of properties of heat-resistant alloy presented in a companion paper.? The detailed precautions in experimental procedure essential for attainment of accurate and comparable data at elevated temperatures cannot be too highly emphasized. THE CREEP TEST Since the fundamental concepts of creep testing have been recognized for the past 20 years, present interest is restricted to refinements in equipment and experimental procedure. The creep-test laboratory constructed for the American Brake Shoe and Foundry Co. is designed to permit 1000-hr. tests in the temperature range of 1200° to 2200°F. with a choice of applied stress extending from 50 to 50,000 lb. per sq. in. in increments of 50 lb. per sq. in. To simplify the calculation of weight combinations, the loading beams (Fig. I) are provided with counterweights to eliminate the tare. The precision of the knife-edges (10.1 ratio) is such that a 10-gram weight placed on the upper specimen grip will be exactly balanced by a 1-gram weight attached to the loading shackle. Check of the loading weights proved the maximum error to be 0.06 per cent. Axial alignment is provided by crossed knife-edges in the grip seats. The furnaces are similar in design to those of Crane and Company, Battelle Memorial Institute, and the U.S. Steel Corporation. An 80 per cent Pt, 20 per cent Rh No. 19 B. and S. gauge wire is used as the heating element. The details of construction are shown in the radiograph reproduced in Fig. 2. The windings are held in place on an alundum tube with alundum cement; the distribution of turns is adjusted to give a maximum temperature gradient of ± 1°F. over a 4-in. gauge length (Fig. 3). To avoid sharp temperature differentials at the ends of the test section, the length of the furnace is four times the gauge length. Sixteen-inch coupons are used to reduce the temperature of the threaded

Jan 1, 1942

By Albert Sauveur

THE senior author of this paper has expressed the belief that when gamma iron transforms into alpha iron on reaching the A3 point, each gamma grain does not change bodily into one or more alpha grains but that the alpha phase forms first at the boundaries and along the crystallographic planes of the austenite grains.1 To quote: On cooling through the point A, at about 900° C., iron passes from the gamma condition to a. new allotropic form generally designated as alpha. This transforma¬tion, however, is not instantaneous. There are good reasons for believing that it begins at the grain boundaries and along the octahedral planes of the crystals and that it progresses until each grain of gamma iron is changed into a grain of alpha iron, the resulting structure being similar to that of gamma iron. Were it possible to retain at room temperature pure iron but partially transformed, it seems probable that a Widmanstättian structure, or rather, as later explained, a martensitic structure would be observed (Fig. 1), consisting of alpha iron at the boundaries and at the octahedral planes, and of a groundmass of gamma iron. In order to confirm, if possible, the accuracy of that view, a number of experiments were conducted. Polished samples of electrolytic iron were heated in a vacuum, maintained in the gamma range for several hours and quenched in different media. It was hoped by such means to produce and retain on the polished surfaces a pattern which would reveal the mechanism of the allotropic transformation. The samples were placed in evacuated quartz tubes, heated to 1000° C. and held 2 hr. at that temperature. The tubes were then immersed in the quenching bath. Iced brine and liquid air were used first. The polyhedral austenitic structure existing at the time of immersion was very clearly revealed (Fig. 2). This is generally ascribed to iron volatilizing at the grain boundaries.

Jan 1, 1929

By Stewart R. Wallace

Members of the Society, it is a very great honor for me to be here today and to have the opportunity of telling you about some things that have been accumulating in the back of my mind for some time. Before attempting to do so, I should acknowledge my debt to the many people who are responsible for my presence here this afternoon. To do this properly, however, would consume much of my allotted time and I will therefore mention only two men, both of whom were directly involved in the discovery of the Henderson ore body. The first of these was Robert Henderson, now dead, who at the time the work was going on was vice president of Western Operations of the Climax Molybdenum Co. Truly, he provided the environment that permitted the exploration program to function effectively, and the deposit appropriately bears his name. The second man I meant to mention was resident geologist at Urad at the time of the Henderson discovery. I think I should explain right here that the Urad ore body and the Henderson ore body, although entirely separate, are closely related deposits, and that both are located at Red Mountain in Clear Creek County, Colo.

Jan 6, 1975

Jan 2, 1976

ALEXANDER BRYDEN Alexander Bryden, clean of engineers in the anthracite mining field, and a member of the pioneer Pittston family, was claimed by death Wednesday, September 26, 1917. The announcement was not a surprise, as he had been in a critical condition for several days. Mr. Bryden had been in failing health for a year past, but his indomitable will kept him at his accustomed duties until quite recently. Two weeks before his death he attended the regular weekly meeting of the Board of Directors of the Miners' Savings Bank in Pittston, Pa. At that time he apparently felt that his end was fast approaching, as he bade farewell to his associates on the bank board. Until a few days before the end, he continued to give attention to business matters at his home, in preparation for the end, which he met unflinchingly. In the passing of Mr. Bryden, northeastern Pennsylvania loses one of the best-known mining engineers, and the community, a man who, throughout his long life, was actively interested in its social welfare and business prosperity. He was for many years prominent in the management of the mining operations of the Pennsylvania Coal Co., and at the time of his death held the position of consulting engineer of the Pennsylvania and Hillside Coal. Companies.

Jan 12, 1917

By G. A. Vissac

MOISTURE in coal must be considered as an impurity, just the same as ash, from the standpoint of utilization of the coal. Being incombustible, it reduces directly the heating value of the coal, and in addition absorbs heat for its evaporation. Its presence means useless expenditures in handling and transportation. In coke plants, extra moisture reduces capacity and may cause damage to brick work and equipment. Accordingly, the removal of extra moisture can be considered just as important as the removal of other impurities, such as ashes, in the modern coal preparation plant. Moisture, which can be removed by heating the coal up to a temperature of 100°C, may be retained in various forms: 1. As a film, on the surface of each coal particle, and in the interstices between particles, retained by capillary forces. 2. Or "occluded" inside the coal particles. This occluded moisture may be either free moisture (as in a sponge), or hygroscopic moisture which varies with atmospheric conditions, (also called "regain").

Jan 1, 1949

By Gordon MacVean

THE adoption of rock dusting, as a safety measure, has made notable progress in the West Virginia coal mines since May, 1925. At that time there were but two mines in the State that were thoroughly rock dusted, mines No. 2 and No. 12 of the Boone County Coal Corp., at Sharpless. Since then it is probable that 75 per cent of the coal operators in the State have given consideration at one time or another to rock dusting. This growth of interest followed the meetings of the various mining institutes all over the country, during the summer of 1925, at which papers were presented, drawing the attention of the coal mining operators to the merits of this safety measure. Yet outside of the experience with rock dusting at the Old Ben Coal Corp., of Southern Illinois, and the Carbon Fuel Co., of Rains, Utah, there had been no actual occurrence in the coal mines of the United States, which could be taken as positive evidence of the efficacy of rock dusting in the prevention of the propagation of coal dust explosions. The U. S. Bureau of Mines, however, had run innumerable tests under conditions which closely approximated actual coal mining conditions and had clearly shown that rock dusting was effective.

Jan 1, 1926

THE first session was held in the small hall of the Academy of Music, on Tuesday evening, February 18th, 1879. The proceedings were opened by the reading, by President Eckley B. Coxe, of the following Address : SECONDARY TECHNICAL EDUCATION. Technical education is a subject to which both the American Institute of Mining Engineers and the American Society of Civil Engineers have of late years given much attention, and deservedly so. We all remember the admirable address of our former President, Mr. Holley, at the Washington meeting, upon this subject, and the very interesting reunion of the two societies in Philadelphia for its discussion. The problem to the solution of which the meeting devoted its attention was, "Shall the practical education of the engineer in the mine, in the rolling-mill, in the workshop, or in the field, precede, be contemporaneous with, or follow his theoretical studies in the technical school ?" I do not propose to add anything to what was so admirably said by so many of our leading engineers on that occasion ; but I shall ask your attention to another question in technical education, which seems to me equally worthy of our consideration, and which, I am sorry to say, has as yet attracted but little attention in this country. It is, "Shall the apprentices (I call them so for the want of a better general name), who are growing up and learning their trades in and around our mines and works, and from whose ranks the master mechanics and foremen of the future must be taken-shall they be provided with some means of obtaining as much theoretical training as may be necessary to enable them properly to understand the various processes and operations that they may be called upon to superintend, and not be obliged to pick up, as best they may, here a little and there a little truth mingled with much error?" In the former case, those who have the ability and industry to avail themselves of the advantages that should be offered to them would fit themselves to become real foremen, men who would understand and appreciate the true engineer and his methods. Of late years the young men of this country who have wished to enter our profession have had great facilities offered to them for so doing ; there have been undoubtedly great improvements in the methods of instruction; and although I am very far from imagining that no further progress can be made, or is demanded, yet I feel sure that

Jan 1, 1879

By Laurence Pellier

Electron microscopical studies were made of the effect of sensitization at 1200oF on a Type-.104 stainless steel with high carbon and low nitrogen and oxygen contents, after solution annealing and after cold working. The loci of the carbide precipitates in the early stages of sensitization were followed in dry stripped plastic replicas. Some observations were made by direct electron transmission on thinned films. Intragranular dislocations showed a high degree of stability through the annealing necessary to produce sensitization. I HE present work was undertaken to determine the effect of sensitization, at 1200°F, for 1/2 hr, on the electron microstructure of a Type-304 stainless steel with high carbon, and low nitrogen and oxygen contents, after solution annealing and after cold working. Many electron microscopical studies of sensitization of 18-8 stainless steels have already been made. Most of them utilized extraction replicas, from which the morphology and composition of the precipitated carbides could be established.'-" ry stripped replicas were seldom used for such studies, although it was demonstrated that they are applicable, in general, to EurveYs of the general microstructure of many alloys' and, in particular, to the observation of precipitated carbides in austenitic stainless steels.3

Jan 1, 1963

By M. W. BERNEWITZ

IT is 27 years since I last visited Broken Hill, New South Wales, one of the world's greatest lead-silver-zinc districts. Then, the flota¬tion of ores was in its infancy. The Minerals Separation process had its birth as a practicability in the Central Mill, which is still operating and yielding high recoveries. The average Australian knows that Broken Hill is an important mining center in a "corner" of New South Wales, but he does not know what a factor it is in the lead, silver, and zinc production of the world. Nor does he realize that among the ramifications arising from metal production at Broken Hill are the great lead smelter at Port Pirie, South Australia, 254 miles southeast; the electrolytic zinc works at Risdon, and the limestone mine at Davenport, Tasmania; the acid works at Cockle Creek, New

Jan 1, 1935

By F. N. Rhines, A. S. Nemy

The mode of high-temperature tertiary creep of 523-0 aluminum alloy was found to be strongly stress dependent. The occurrence of necking and/or fissures during tertiary creep exhibited a sequence with varying stress, wherein fissures with no necking occur at a minimum stress and necking with no fissures occur at a maximum stress. At an intermediate stress, tertiary creep begins without necking but with fissures in a region just beneath the external surface, followed by necking and the development of fissures along the axis of the specimen. The results are interpreted in terms of grain boundary gliding and the hydrostatic stresses produced by restraints to grain boundary gliding. THERE appear to be two possible reasons for the existence of a period of accelerating elongation prior to rupture during high-temperature creep in metals; namely, 1) a change in the structure of the metal itself, leading to a change in its response to loading, and 2) a reduction in the cross section of the metal resulting in a higher unit loading. Howe,' by annealing and retesting broken low-temperature creep specimens, found that irreparable damage is done once a metal is subjected to creep. Andrade2 first pointed out the association between the reduction in cross section and the increase in creep rate. The present research was designed to investigate both of these factors by retesting specimens machined from material which had been subjected to high-temperature creep testing short of rupture. EXPERIMENTAL METHOD An aluminum alloy, 52s-0, was selected for these studies because it is constitutionally simple, is strong enough to be relatively insensitive to mechanical damage during machining,3 and undergoes accelerating creep in a convenient temperature range. This alloy is hardened by 2.6 wt pct Mg in solid solution and is not subject to overaging effects; it has a very small quantity of an insoluble impurity phase, Mg2Si, finely dispersed throughout its micro-structure. Creep specimens, similar in design to ASTM 0.252-in. tensile specimens, were machined from 3/4-in. round stock and the surfaces were electro-polished. A 24-hr anneal at 500°C was then applied to stabilize the grain size to an average diameier of 0.27 mm. Subsequent heating for as long as 700 hr at the intended test temperatures produced no change in the tensile properties, indicating a well-stabilized state of the material. Corresponding to each of the typical testing conditions listed in Table I, one creep specimen was tested to destruction and this test was employed as a guide in the selection of times for subsequent tests. Duplicate creep tests were then run to various points along the creep curve to produce specimens which were used to determine changes in mechanical properties and microstructures. The latter were examined at the midsections of the specimens. Other specimens were tested to various stages of tertiary creep, after which they were remachined to new cylindrical test specimens, electropolished and re-tested in creep. RESULTS The major findings of this investigation may be illustrated by a comparison of the results of three sets of creep tests. These were run at 400°C at three stress levels, namely 750, 1000, and 1500 psi. In presenting these results in Figs. 1, 5, and 8, the creep curves are given in pairs: That curve of each pair which is drawn through filled circles corresponds to the initial test, and the curve drawn through open circles (and designated by - R) represents the result of retesting the same specimen after machining to a new cylindrical surface. The load was readjusted to the original unit stress at the beginning of each retest.

Jan 1, 1960

By Stephen Krickovic

THERE is today no proven continuous mining machine that can be used under all the varying conditions found in most bituminous coal mines. During the last five years, however, both the machines and methods of using them have been improved. Coal operators can now exercise a fair degree of selectivity, except those who must struggle with thick and hard partings and operate in seams less than 40 in. thick. It must be realized, then, that more than one type of continuous miner may be used advantageously in the same coal mine. Although this appears to violate the standardization generally sought after, the gain can more than offset added maintenance and, to a lesser degree, operating problems.

Jan 12, 1957

By E. E. AGGER, Arthur Notman

THE proposal has been made in a bill introduced into Congress at the last session by Representative Jones of Michigan that an import duty of 6 c. per lb. shall be placed on copper. This action is urged after eighty years of prosperity for the industry in this country; during most of which copper has been on the free list, and during all of which a tariff would have been without real effect. To comprehend the general situation upon which this action would be imposed, we must refer to the past history of the industry and its trends at the present time. The following table supplies us with a picture of the physical growth of the industry in this country and its relation to that of the world as a whole down to Jan. 1, 1921:

Jan 1, 1925

(Under this heading will be published notes sent to the Secretary of, the Institute by members or other persons introduced by members.) Development and production. Member open for engagement. Past year in war mineral field work, operation and production. Ten years' thorough experience in both subordinate and executive positions, gold, silver and copper in the United States, Mexico, and South America. Age 37, married. Minimum salary $3600. Interview. South or East. A-577. Engineer and executive. Captain U. S. Army, age 36, expects discharge before July 1. Seven years' mining and metallurgical experience. Six years with large technical college as assistant professor of mining and directing extensive experimental work. Desires position as executive or research engineer with reliable company or as professor of mining with first-class college. A-909. Mining engineer. Twenty-five years' experience including mine and works operation, construction, plant installation, and mine examination. Speaks Spanish. A-1173. Metallurgical engineer. Twelve years' laboratory and operating experience, covering copper blast furnace, roasting, reverberatory smelting and latest Cottrell treater practice on copper dust and zinc dust. Technical graduate. 36 years of age, married. Highest recommendations. Open for immediate engagement. A-2354. Mining engineer. Junior Associate. At liberty about July 1. Captain Heavy Artillery. Single, age 24. Go anywhere. Best refer-ences. A-2843. Engineer. Age 26, single, graduate Missouri School of Mines, B. S. in Mis. Met. E. Desires position with oil or metal company in any capacity. Location immaterial. At present engaged, desires change. A-2844.

Jan 7, 1919

By Baxter C. Madden

Stress corrosion is defined and certain examples are illustrated. A number of test methods, to determine the resistance of materials to stress corrosion, are being developed at Wright Field. The criterion as to the validity of a method is stated. Three types of specimens and the method of stressing each type are described. Five different corrosive conditions are set forth. The results of tests to date, although too few for any general conclusions to be arrived at, are presented. The program for the continuation of the investigation is indicated. A bibliography is included. The development of the method of loading a cantilever-type specimen, so that a nearly constant stress at a large deflection may be realized, is presented as Appendix I.

Jan 1, 1945

By J. Gordon Parr, D. H. Polonis

The formation and subsequent decomposition of metastable phases in Ti-Ni alloys containing up to 11 pet (atomic) Ni have been studied. The decomposition of a completely retained ß phase and of a completely transformed 8 phase in a 6 pet alloy has been followed by X-ray diffraction and metallographic methods and by hardness determinations made during the process. The possible mechanisms of the reactions are discussed. PREVIOUS investigations of the Ti-Ni system have usually been limited to phase diagram studies; but little attention has been given to metastable phases and tempering processes. These are important, however, since equilibrium conditions are rarely achieved—nor, perhaps, are they desired—in practice. Up to the present time the available transformation data for titanium alloys appear to be restricted to isothermal transformation curves for selected binary and ternary systems. No quantitative studies have been made of the mechanism by which equilibrium is approached. Several independent investigations have been carried out to determine the Ti-Ni phase diagram. Early work by Wallbaum' and later by Long et al.' produced tentative phase diagrams which were not representative of true binary conditions, since the alloys were contaminated with oxygen and nitrogen. The most recent diagram (Fig. 1) is due to Margolin et al.," and a slight modification of the a + ß/ß boundary (shown dotted) has been proposed by McQuillan.' The structure of the phase Ti,Ni was shown by Duwez and Taylor" to be face-centered-cubic, with 96 atoms per structure cell. The formation of a martensitic ß phase (close-packed-hexagonal) in Ti-Ni alloys has generally been observed when specimens of low nickel content are rapidly cooled from the 0 (body-centered-cubic) range. Margolin et al. reported an increasing tendency for P to be retained in lump specimens as the nickel content increases. McQuillan' has studied the effect on the microstructure of delay time in quenching, and has reported the formation of pro- eutectoid a precipitate in a quenched hypoeutectoid alloy. In a previous study of Ti-Fe alloys," experiments were made on powder specimens produced by filing alloy ingots. Techniques were devised for the preparation and heat treatment of alloys, and X-ray diffraction methods were used both for structure determinations and phase ratio estimations. A similar approach has been made in this study of Ti-Ni alloys. Experimental Methods Ten alloys ranging from 0.25 pet to 18 pet Ni* * All compositions are in atomic percentages unless otherwise stated. were prepared from iodide titanium bar stock (hardness Rf 72) and Johnson-Matthey spectrographic standard nickel by levitation melting.' As a check

Jan 1, 1957

By L. L. Oriard

In order to predict the influence of blasting on slopes, one must first understand the action of explosives, the manner in which rock is broken or displaced, and how seismic waves are transmitted, and the nature of these seismic waves. In this paper, the author describes the action of high explosives on rock masses, beginning at the source of the explosion, extending through the zone of rupture to a distance where only elastic waves of low energy persist. The paper describes the relationships between explosives charge quantities and distances, including the character and intensity of the seismic waves in various types of terrain. In looking at the analysis of slopes subjected to seismic waves, it has been common practice to assume a simplified model in which the anticipated acceleration is applied horizontally to the slope as an equivalent static force, or a model in which there is a rigid base subjected to mechanical shaking. Such models do not accurately portray blasting activity taking place within or near the slope in question. In dealing with blasting effects, it is important to under- stand seismic wave types, wave lengths, attenuation and transmission paths, as well as vibration intensity. In most cases, those slopes that are the least stable under static loading will also be the least stable under dynamic loading, although there may be rare exceptions. Thus, the more that is known about a slope statically, the better will be the assessment of it dynamically.

Jan 1, 1983

By R. D. Rubright, Owen J. Hart

In the Bingham district over a span of more than 90 years, 43,947,104 tons of "non-porphyry" copper, lead, zinc, gold, and silver ore have been mined from a folded and faulted alternating series of Pennsylvanian and Permian limestones and sandstones and from some Tertiary intrusives. This ore came from six major mine areas located east, south, and west of the Bingham stock, site of Kennecott's porphyry copper deposit. The sediments were affected by varying degrees and types of metamorphism within 2000 feet or more of the Bingham stock. The intrusives consisting of the mineralized Bingham and the unmineralized Last Chance stocks and numerous dikes and sills of granite and monzonite were intruded into the asymmetrical northwest-trending and plunging Bingham syncline. Extrusives, although present, contain no ore. The bulk of the non-porphyry ore in the district was found above the Midas thrust. The primary ores are found in three major types of deposits: concordant bedding fissures, crosscutting fissures, and replacement deposits. These deposits consist of both copper and lead-zinc ore bodies that contain various amounts of gold and silver. These are in places roughly zoned both laterally and vertically and have been mined for up to 10,000 feet outward from the center of the Bingham stock and up to 5000 feet vertically below the surface. Secondary ore was of minor importance and was found in and under the oxidized zone at shallow depths. Genetically the Bingham stock, the ores, and related phenomena have had a common source.

Jan 1, 1968

By J. E. Harris

By elimination of other possible nucleation processes, it has been demonstrated, for commercially pure magnesium and a Mg-Al alloy, that at stresses less than that necessary for triple-point cracking creep cavities are most probably nucleated heterogeneously at second-phase particles. Evidence for the existence of such particles is presented and the role of grain boundary sliding in the nucleation process is examined quantitatively. DURING creep deformation of polycrystalline magnesium and its dilute alloys in the temperature range 0.45 to 0.7 Tm (Tm = absolute melting temperature) cavities form mainly along grain boundaries oriented normal to the stress axis and failure eventually occurs by their growth and impingement.' The possibility of low-ductility creep failure of magnesium-alloy reactor cans during service has prompted a number of studies of cavity formation in these materials.2-5 In this paper divergent theories of cavity nucleation6-10 are examined critically and conclusions drawn regarding the most probable mechanism of formation of cavities in magnesium. The paper is divided into two parts. The first section consists of the review and quantitative assessment of the possible role of grain boundary sliding in the nucleation process. In the second part an experimental program is described where an electron-microscope technique has been used to determine if second-phase particles exist in as-received commercially pure magnesium and in a magnesium alloy 1) THEORETICAL REVIEW Possible nucleation sites for creep cavities are: a) high-angle grain boundary triple points,11-14 b) subboundary/grain boundary intersections,15-18 c) ledges in the grain boundary, 19-25 d) second-phase particles. 9,26-30 Each of these possibilities is now considered with special reference to deformation of magnesium. 1.1) Triple-Point Cracking. The stroh31 condition to nucleate fracture is: " > vr [1] where ss = applied shear stress, ? = surface energy, C = shear modulus, L = length of sliding interface. This relationship is independent of the nature of the interface and it is possible to calculate the stress concentration at the end of a sliding high-angle grain boundary and thus deduce, approximately,* the minimum applied stress necessary to nucleate triple-point cracking. Such theoretical predictions for Nimonic alloys have been made by McLean13 and found to agree quite closely with the minimum stress determined by experiment. Stresses capable of nucleating triple-point cracking should also be sufficient to nucleate fracture at a grain boundary due to intragranular slip, for the lengths of sliding interface in the two cases are approximately equal. Thus the minimum stress for triple-point cracking should represent a demarcation between failure due to general "cracking" and that due to cavitation. Hauser, Landon, and Dorn32 have demonstrated that for polycrystalline magnesium in the temperature range 78° to 298°K the fracture stress is inversely proportional to the square root of the mean grain diameter. As pointed out by stroh31 this result indicates that Eq. [I] describes the fracture characteristics of magnesium at low temperatures. Heal3 has reported that for rapid deformation (112 pct hr-1) of polycrystalline magnesium the transition from cracking to cavitation occurs in the temperature range 175" to 275°C. He also presented the fracture-stress values for the same material tested under similar conditions. From Eq. [I] taking G = 1.3 x 10" dynes , ? = 600 ergs . cm-2,33 and L = 0.017 cm, a Stroh-McLean13,31 tensile stress of -266 kg. cm-2 is calculated, corresponding to a transition temperature of -190°C; this is in

Jan 1, 1965