Search Documents

By Franco de Castro Bubani

Cu-base alloys (Cu-Zn-Al, Cu-Al-Be, Cu-Al-Ni), depending on their composition, have martensitic transformations that can be thermally or mechanically induced between a metastable structure called austenite and one or more metastable structures called martensites. In single crystals, depending on the specific composition of the alloy and the crystallographic orientation of the tensile axis, martensite-martensite transformations can be mechanically induced. The hysteresis associated to these martensite-martensite transitions is usually much greater than the one associated to the austenite-martensite transformation. Thus, martensite-martensite transitions are potential candidates for energy dissipation in a mechanical damper. Possible applications that would benefit from high hysteresis include seismic damping devices, dampers for satellites and the aerospace industry, defense and others. We present pseudoelastic cycling results of alloys submitted to different thermal treatments. Our conclusions highlight the fact that, under certain conditions, Cu-base alloys deliver better damping performance than commercially available SMAs and even the new Fe-base SMAs.

Aug 7, 2018

By G. Martino, F. Silva, Emmanuel Marchal

The definition of the chemical specification at multiple steps of the steelmaking process is very common in the industry. Among all elements and compounds, the Sulphur content has a special control over several stages, from the coal blend to the final products. Coke, iron and steelmaking specialists usually agree on a static specification for each intermediate product according to their local operation capacity and production cost. However, local decisions have major impacts on the whole production chain and many global factors should be considered in order to make the best decision. In this study, we will exemplify focusing on Sulphur content concepts and techniques that could be applied to many decisions in an integrated carbon steel plant. The variation of coal and coke prices, the desulphurization cost and time, the processes operating points, the hot metal rate at converters, prices and demands of low and ultra-low Sulphur steel grades are some of the integrated factors that are usually disregarded during the specification process. Mathematical modeling presents itself as a proper option into dealing with all the complexity that emerges from integrating all these processes' trade-offs and decisions. This study presents the results of a mathematical model that encompasses economic, thermal, chemical, and mass balances, physical quality of materials and productivity constraints of all processes of a hypothetical integrated carbon steel plant. It optimizes the iron and steelmaking process on a global and unique objective, dynamically defining targets for product quality to achieve the lowest steel production cost. This study details multiple market-plant scenarios in order to compare economic and operating results of a static vs dynamic specification practice.

Oct 1, 2019

By Javier Martinez Rubio

In this paper we will discuss the benefits of a very innovative way of introducing MgO in the blast furnace operation through the sinter, using mini lumps of dunite. By changing the traditional way of using an MgO bearing material in fines form (particle smaller than 5 mm), most of the MgO inserted material behaves as inert during the sintering process, with the effect of having the following parameters (among others) improved: productivity at the sintering bed, permeability inside the blast furnace, energy consumption, stability of the operation.

Aug 16, 2017

By Jovanir Francisqueto, José Fagundes, Nayara Neves Coutinho, Marco Túlio Costa

The purpose of this project is to increase the visibility of which will be daily produced on the hot strip mill (HSM). The forecast was performed through the implementation of an automated tool for weekly HSM production planning. The project was started with the definition of the weekly planning process, through the determination of the main business objectives, like as: priorities of service (customers and delivery date), definition of HSM’s rules and restrictions of operating resources. Using a sophisticated mathematical model, through the computational simulation is possible the experimentation of various production scenarios, allowing the visualization of volumes by type of sequence, clients / priorities, mix to be produced, cylinder change quantity forecast, better forecasting of the productivity of the HSM, consumption of utilities, within others. Main benefits: sequencing which production orders should be produced, reducing unforeseen stops due lack of material, improving the quality of the stock which allows the reduction of the aging of slabs in the slabyard and the vision of customer services. Computational simulation as a weekly planning tool achieve, with other benefits, to present alternatives for better decision making.

Oct 6, 2019

By Piezanowski Ludivine

With the aim to reduce the hot metal production cost, ArcelorMittal Gent decided to integrate more ores with finer particle size distribution in the raw material mix for the production of blast furnace sinter. As a consequence of such an increase of finer material in the sinter raw mix, the sinter machine productivity and the quality of the sinter are affected. In order to compensate this impact, modern granulation technology can be employed. Within this context, ArcelorMittal Gent has invested in a vertical intensive mixer. The equipment was placed before the existing drums, with a function of “mixer”, whereas the drums are fully optimised for the nodulizing process. The paper presents the results of the industrial operation during the commissioning phase of the new equipment. Gradually increasing the proportion of fine material in the sinter raw mix has made it possible to compare the performances of the old system using drums for mixing and pelletizing with the new system using an intensive mixer combined with a nodulizing.

Aug 1, 2018

By Enrique Francisco Somolinos Garcia-Morales

In this paper we will discuss the benefits of a very innovative way of introducing MgO in the blast furnace operation through the sinter, using mini lumps of dunite. By changing the traditional way of using an MgO bearing material in fines form (particle smaller than 5 mm), most of the MgO inserted material behaves as inert during the sintering process, with the effect of having the following parameters (among others) improved: productivity at the sintering bed, permeability inside the blast furnace, energy consumption, stability of the operation.

Aug 1, 2018

By Paul Riches

LR Process Expert is a cost-efficient process automation system for all types of long rolling mills, including, rod, bar, section, rail, reversing mills, and flat blocks. The system performs a wide range of tasks for optimized operation – from suggesting pass schedules to calculating and downloading optimized mill settings according to the availability of rolls. LR Process Expert also monitors and collects data from the raw material stage through to the finished product. It delivers valuable mill reports to the operator staff and management so they can easily assess a plant’s performance and optimize production. Defined Key Performance Indicators (KPIs) help to assess a plant’s performance; this system is not limited to one plant but can enable plant-toplant performance at corporate level.

Aug 16, 2017

By Marcel Antonio Arcari Bassani

In the mining industry, it is common to have data collected in various formats. In an open pit mining operation, at the early stages of exploration samples are obtained from diamond drillholes. During the production stage, samples are collected from blastholes. The last is more numerous but less precise. From a geostatistical view, this dissimilarity has to be considered to integrate the two sources of information. To combine this different data, three methodologies were investigated: simple kriging with local varying mean, cokriging and ordinary kriging. The exhaustive Walker Lake data set was used and it is considered the source to obtain the true grades. Initially, samples were obtained from the exhaustive data set at a regular spacing grid of 20 x 20 meters. Next, samples were obtained again from the exhaustive dataset at a regular spacing of 5 x 5 meters and a relative error of 25% was added. Then, both data were used to estimate blocks using the three methods mentioned. The grade tonnage curves were compared with the true block grade distribution. Moreover, the block misclassification was evaluated. The results showed that ordinary kriging produced estimates closer to the true block grade distribution and reduced the block misclassification.

Aug 8, 2018

By Mirko Jurkovic, Thomas Hueper, Jens Kempken

The high competition scenario pushes the steel producers business. Zero defect requirements from customers force the operators for additional efforts in process control and quality management. PQA® has been developed as an advanced process and quality management assurance solution. It is focusing on the analysis of process data, equipment information, inline quality measurement devices and trend analysis. The paper describes the structure of the advanced process and quality management assurance solution PQA®; it gives insights on the expert know-how, process and quality evaluation and points out the benefits like cost reduction, improvement yield and customer satisfaction increase.

Oct 1, 2019

By Michael Windhager, Karl H. Ziehenberger

ULTIMA® are high performance, centrifugal cast, double poured (CC duplex) work rolls. This paper describes the principle of the ULTIMA® roll concept and its wide range of usability. The ULTIMA® concept provides a solution for rod and bar mills to increase performance and output, even under harsh rolling conditions. The main focus is on highly loaded mill stands that require both high wear resistance and resistance against thermal fatigue, like pre-dog bone, dog bone, slitter. Specific case studies of quite different mill configurations and rolled product mix prove the positive impact on production yield, mill and roll shop operations, and profitability in terms of TCO (total cost of ownership).

Oct 1, 2019

By André Carlos Silva

Dewatering stage is among the most important industrial unit operations, and is wide adopted in many different industries, due the fact that a large portion of industrial products is produced using suspensions of solids in liquids. Nowadays the mineral processing tailings disposal is a big problem due the environmental degradation produced. The phosphate rock processing in Anglo American Phosphate Brazil, situated in Catalão/Go/Brazil, generates around 180 t/h of tailings for a plant feed of 480 t/h (approximately 37,5% of the processing plant feed), with 5 to 10% of solids and approximately 14% of P2O5. Nowadays the tailings are sent direct to the tailings dam. The present work proposes the paste production using with the tailings from phosphate rock processing plant divide in two different stages. The first one composed by the free settling of the material in presence of industrial flocculants in a graduated cylinder with 2.0 L of internal volume for one hour, in the same way it must occur in conventional thickeners. After that time, the clarified liquid was drained and the remaining pulp was sent to the second stage consisting in the tailings vacuum filtration. Ten different flocculants and nine different filter media were tested. The found results were satisfactory for paste tailings production with solids percentage around 65%.

Aug 8, 2018

By Steferson Ferreira de Oliveira

Desenvolvido nos últimos anos, o processo NDE, vem se tornando uma maneira promissora de usinar e nitretar simultânea a superfície de materiais metálicos. A Usinagem por Descargas Elétricas (EDM) é um processo de usinagem não convencional que tem grande potencial em aplicações de engenharia de superfície, ao melhorar a resistência superficial do material por meio de tratamentos termoquímicos, como por exemplo, a nitretação. Propriedades como: baixa densidade, boa resistência à tração (comparável à de muitos aços ligados) e excelente resistência à corrosão, possibilitam a aplicação do titânio e suas ligas nas indústrias aeroespacial, naval, química e automotiva e ainda no campo da medicina. Porém, raramente são usados como peças sujeitas ao deslizamento, devido a sua devido à sua baixa resistência aos mecanismos de desgaste abrasivo e adesivo e alto coeficiente de atrito. O tratamento termoquímico de nitretação pode solucionar esta restrição. Além de aumentar a resistência ao desgaste, o nitreto de titânio melhora a biocompatibilidade de suas ligas. O objetivo deste trabalho foi estudar a camada nitretada na liga de titânio Ti6Al4V por meio do processo de Nitretação por Descargas Elétricas (NDE), usando como fluído dielétrico solução de água deionizada e ureia granulada, como fonte de nitrogênio. Uma máquina de EDM por penetração foi utilizada no processo. Cobre e grafite foram utilizados como materiais dos eletrodos ferramenta. Foi avaliada a usinabilidade da liga Ti6Al4V com solução de água e ureia, relacionada aos parâmetros: taxa de remoção de material (TRM), taxa de desgaste (TD) e desgaste volumétrico relativo (DVR) para eletrodo de cobre e de grafite. Para caracterizar a camada nitretada foram realizadas microscopia óptica e medição de microdureza Vickers. A formação de nitretos na superfície foi avaliada por meio de difração de raio-x. Imagens metalográficas da seção transversal da superfície mostraram a formação da camada nitretada, devido ao ganho no valor da dureza. Os parâmetros relacionados à usinagem apresentaram valores que indicam um melhor desempenho quando se usa eletrodo ferramenta de cobre em relação à grafita. Nitretos de titânio foram observados no difratogramas da amostras nitretadas por NDE.

Oct 30, 2017

By Túlio Magno Fuzessy de Melo, Luciano Santos Marques, Vicente Tadeu Lopes Buono

The influence of the coiling temperature after hot strip rolling on the microstructure and on the tensile and hole expansion properties of a 800 MPa multiphase steel was investigated. For the temperatures between 150°C and 600°C the microstructure consisted of a ferritic matrix with a dispersion of fine martensite-austenite (MA) and regions of degenerated upper bainite. In all cases the ferrite presented a heterogeneous mixture of polygonal, quasi-polygonal and acicular grains. The yield and tensile strengths showed a tendency of decreasing with the increasing coiling temperature, probably because of the larger fraction of MA particles at lower temperatures and higher fraction of quasi-polygonal ferrite at higher temperatures. The elongation was not significantly affected by the variation of coiling temperature. The average hole expansion ratio showed a maximum of 80% for the material coiled at 400°C and fell below 50% only for the coiling temperature of 150°C, probably due to the larger hardness difference between the ferrite matrix and the MA particles.

Oct 1, 2019

By Antônio Augusto Gorni, Fabio Adriano da Silva, Emanuelle Garcia Reis, Afrânio Márcio Costa

Gerdau Ouro Branco´s plate mill started the operation in 2016 with high level technology. Stands out the capacity to produce different thicknesses in a same plate, therefore allowing special service for sectors such as building structures, bridges, shipbuilding and mechanical applications. The purpose of this study is to present the first results obtained in this innovative product in Brazil. Some slabs of EN10025-2 S355JR+AR steel were rolled and were evaluated the dimensional tolerances, mechanical properties uniformity, grain size, surface and internal qualities. In addition, a correlation was observed between slab and plate thickness reduction and internal plate quality. The results show that this technology can be used with adequate performance for these steel grades in the current market.

Oct 1, 2019

By Erich Bartel

The Kocks Rotation Mill - KRM- is an innovative elongation method for seamless tube production up to 4.5’’ diameter at production levels up to150,000 TPY. Using the principle of cross roll elongation, the machine rotates four rolls around the workpiece. A retained mandrel sets the wall thickness to a precision that exceeds existing industry norms. The KRM process performance has been truly excellent. Attributes include high billet weights, elongation of up to 9.5 in one pass, and eccentricity at or below +/- 5.0%. The flexibility of the process allows a wide range of steel grades to be produced at any wall thickness with little or no mill down time. Surface quality and yield are also greatly improved. Based upon the small foot print of the KRM rotor as well as the simple mandrel manipulation system, the installation cost of the KRM is significantly lower compared to other elongation methods. The reasonable cost of the machine, combined with greatly reduced foundation requirements, reduced ceiling height as well as simple utility connections reduce the initial investment for a new or upgraded mill. Finally, lower roll and mandrel costs allow high quality production at greatly reduces cost/ton.

Aug 16, 2017

By Henrique Silva Furtado

Light meter is an ArcelorMittal innovation that uses off-gas light intensity to predict bath carbon, which is akin to the visual cues that the operators employ to finish a blow. Light meter enables the prediction of end point that is independent of any operator’s judgment. The results have been in general consistent with the actual carbon content at BOF end point at Tubarão. Besides some outliers that occurred due to strange intensity curves, the system implemented in Tubarão BOF 3 reported a carbon prediction error statistic that is very similar to dissolved oxygen–carbon end point statistics. Preliminary trials using light meter without any filter improved carbon hit ratio significantly.

Jul 30, 2018

By Roman Vaynshteyn

In places where Blast Furnaces are usually located, climatic factors may be unfavorable. Raw materials may be exposed to e.g. rain during transport/storage, bringing moisture into the process with consequences for stability and hot metal cost. This paper describes a technology for drying and pre-heating pellets and coke in the stockhouse. It does not require additional handling or logistical equipment and does not introduce extra transfer steps and degradation. Not only can moisture content be reduced, it can be controlled to a stable level by the operator.

Aug 16, 2017

By Valeria Collini, Antonello Mestroni, Enrico Plazzogna

The Danieli Group is deeply involved in the technological improvements stimulated by Industry 4.0 concepts widely applied to the metals industry and process automation. The so-called "Intelligent Mill" is the natural evolution of the company’s consolidated know-how and undisputed leadership in the fields of mini-mill and turnkey plants. Complete and structured data collection is the basis for real-time analysis and process optimization in terms of quality, efficiency and easy maintenance. A centralized repository of information is possible thanks to the strong interconnection between process control system architecture and intelligent sensors, together with dedicated software tools leading to an intuitive approach to data analytics.

Oct 1, 2019

By Gigliola Salerno

The carbon-epoxy composite has high specific resistance and strength, which means specific applications. However, its behavior under compressive stress could be decreased by delamination, needing more detailed studies. The main purpose of the present work is to verify the mechanical properties in bending process considering two different fiber orientations. The composite materials were made by woven fibers and epoxy resin. Primarily, the carbon fiber fabrics suffered a superficial physical treatment called silanization, in order to developing a better chemical adhesion between fibers and resin. After the superficial treatment, the layers were embedded with epoxy resin. The composite resin’s cure was made in a Fanem heater, model 320, during 1 hour at 120°C at 1.5 bar; subsequently the specimens were cut by water jet. Specimens oriented in 0°/90° and 0°/90°/45 were manufactured and taken to bending tests, accordingly to the ASTM E855 and D790 standards, in an universal testing machine MTS – Material Test System, full capacity of 250 kN. It was concluded that all specimens failed by tension. Specimens with internal void volumes results in lower flexural modulus and those with presence of fracture mechanisms, like delamination, showed lower strength values. Scanning Electronic Microscopy demonstrated the damages involved during bending process.

Oct 30, 2017

By Claudio Pereira Diogo

A lot of galvalume/aluzinc steel sheet was furnished to a metallic roof manufacturer intended for tile fabrication. But, according with the roof manufacturer, that coils develops a different superficial aspect during processing. The purpose of this work was to provide an explanation for the appearance of the observed surface on one side of the coils. In order to find out the origin of the problem, mechanical and microstructural characterization tests were done at INSPEBRAS with the support of a partner laboratory. The results are described in this paper with their analysis and conclusions.

Aug 16, 2017