Search Documents

By Remo Grandori

The Umiray Angat 13,2 km long tunnel in Philippines have been bored through extremely variable and difficult ground conditions including a number of special events. In particular the following adverse conditions were found: faults in decomposed ground, high temperature rocks, extremely rapid and important convergence phenomena, water inflows up to 800 litres per second. The special El Nino climatic conditions caused a long dry season and lower the level of the lake that was granting the access by barge to the site under the minimum navigable level. Many equipment have had therefore to be transported to site by a 10 ton capacity helicopter, after having been partially dismounted. For the same reason most of the tunnel drive have been bored servicing the site by 1 ton capacity helicopters to transport materials, spares and personnel. In order to overcome the above geological and logistic problems several innovation were introduced and tested in this project. Despite all that difficulties the 13,2 km of tunnel were bored in about 24 months, with a global average of 500 m/month.

Jan 1, 2001

By James S. Browning

Recovery of fine mica from a sample of impounded tailing from the Dixie Mines, Inc., crushing and screening operations, Heflin, Ala., was investigated to determine if plant losses of mica could be reduced while econmically producing a commercially acceptable mica concentrate. Conventional wet-tabling and agglomerate-tabling methods yielded concentrates assaying about 95 percent mica from the tailing that contained 17 percent mica. Products containing about 98 percent mica and accounting for mica recoveries of 86 percent were obtained by flotation, using as reagents sulfuric acid, kerosene, and coco amine acetate (a mixture consisting chiefly of dodecyl and tetradecyl amine acetates). The results of the batch flotation tests were verified by tests in a small continuous flotation pilot plant.

Jan 1, 1963

By Dave Bulled

"This paper describes the design of a molybdenite flotation circuit using FLEET technology applied to kinetics data produced from laboratory flotation testing and distributed across the blocks of a mine plan using a geostatistical approach. The geostatistics assigned the statistical error that arises from having a limited amount of sample testing data to the kinetics estimates of each block of ore in the mine plan. The final design then included a quantification of risk based on the accuracy of the block flotation kinetics and model fitting. The design made reference to the extensive technical reports describing earlier metallurgical test work including some pilot plant work over thirty years ago.The testing involved conducting MinnovEX Flotation Tests (MFT) to determine the rougher flotation kinetics at the specified reagent conditions and rougher-cleaner tests to determine the change in kinetics resulting from regrind. These flotation kinetics were used within FLEET simulations to create a full-scale flowsheet and plant design including recommended equipment sizes and the forecast of operating results. Measurement of detailed flotation kinetics for a wide range of samples allowed the effect of size of grind and efficiency of classification (i.e. width of size distribution) to be predicted for the whole ore body.INTRODUCTIONAdanac Moly Corp. proposed to develop a 20,000 ton per day mill to produce high quality molybdenite concentrate from its Ruby Creek resource in north-western British Columbia. It is a relatively clean low grade porphyry-monzonite occurrence containing minimal quantities of other sulphides such as chalcopyrite, pyrite, sphalerite and galena. Molybdenite occurs mainly as coarse flakes with lesser amounts of finer sized values. An optimum plant design was required to can achieve the predicted operating results, at a known level of risk, while treating the variability inherent in the ore body."

Jan 1, 2007

By Guillermo Manrique

El presente texto describe las estrategias planteadas por la empresa Southern para la convivencia pacífica con las comunidades afectadas por el desarrollo de las operaciones mineras. Para ello, se requiere definir los objetivos y la filosofía corporativa (responsabilidad social) que garantice el apoyo de dichas propuestas. Asi también se realiza un estudio base de la comunidad, donde se priorizen las necesidades de las comunidades a través de la estrategia de concertación y así ejecutar proyectos participativos de desarrollo social. Finalmente, la información recolectada se sustenta y validad por las experiencias llevadas a cabo en las 36 comunidades del entorno de las operaciones de SPCC, convirtiéndose en un aporte para el tratamiento comunitario.

Sep 13, 2001

"Canada Centre for Mineral and Energy Technology (CANMET)Natural Resources CanadaMining and Mineral Sciences LaboratoriesA. Address and Contact Information555 Booth StreetOttawa, Ontario, Canada, KIA OGlWebsite: http://www.nrcan.gc.ca/Contact: Philippe Dauphin, Manager, Business DevelopmentTel.: (613) 947-0798Fax: (613) 947-0984E-mail: pdauphin@NRCan.gc.caB. Type and Size of FacilityScope of facilitiesCrushing from minus 4 in. to 10 mesh; grinding - rod, ball, vibration, SAG and impact mills; classification- screening, cycloning, mechanical, hydraulic and dry centrifugal classifiers; froth flotation - automated, column, and frothless flotation; gravity separation- wet and dry; magnetic separation - high gradient, high and low intensity, wet and dry; electrostatic separation; heavy-media separation; calcining; cyanidation; thickening; filtration; drying - fluid bed and freeze drying; pelletizing; microwave.SpecialtiesMineral beneficiation research and development; flotation of sulphides - flowsheet improvement, selectivity, reagent selection; novel flotation techniques; analysis of thiosalts formation; use of mineral processing techniques for recycling.Specialized equipmentHigh gradient magnetic separation, Denver XRF on-stream analyzer, automated flotation cell.Complementary support servicesElectron microprobe; SEM; STEM; X-ray diffraction; particle size analyzer; mineralogical and analytical chemistry services; physical chemistry; hydrometallurgy; pyrometallurgy; engineering and economic evaluation; mechanical shops; technical information services and library integrated with the National Library System of the National Research Council."

Jan 1, 2000

By B. B. Dhar

Slope stability at the proposed mine in Rajasthan was analysed in two dimensions using a finite difference code. The properties of the rock material were determined in the laboratory and subsequently modified to approximate those of the in situ rock mass. Geotechnical mapping was undertaken to determine the critical orientation of structural discontinuities. The results of the work indicated that an open pit 148 m in depth would be stable with overall slope angles of 60 degrees

Aug 1, 1994

By A. J. Basu

New technologies, such as computer based learning, wireless computing, internet2, online courses, distance learning, and in general multimedia applications are being implemented in the higher education sector in an increasing manner. However, these implementations are not coherent, and lack standards. However, one example of the existing standards is the development and implementation of the virtual learning environments. These technology tools help in delivering the eLearning objectives. There is a major initiative in Europe (eEurope action plan) in promoting eLearning towards creating a knowledge-based society. Technology implementation is the major driver for achieving the eLearning objectives. A two-year pilot project on implementing technology tools including virtual learning environment (VLE), video-conferencing, and simulation and visualization was carried out for providing a blended learning environment for undergraduate and graduate students in Mining Engineering (undergraduate) and Mineral Deposit Evaluation (M.Sc.) course at the Imperial College London. The pilot project was funded by the Imperial College Centre for Educational Development (ICCED). The project did contribute towards activities for creating an institute-wide eLearning strategy in line with the eEurope action plan.

Jan 1, 2003

This report is the 26th in a series summarizing Bureau of Mines research and technologic work on coal and related investigations and the 8th of these reports to be issued on a calendar-year basis.1 It reviews briefly work in progress during 1961, and it provides references to publications by Bureau personnel during 1961 and also to a few older papers that were not cited in prior reports of this series. Details about some of the researches mentioned may be obtained by referring to the publications cited in the footnotes or in the further list in the Bibliography; other phases of work are reported here for the first time and will be covered in more detail by later publications. The coal program of the Bureau of Mines extends over the wide range of applied and theoretical studies indicated by the table of contents of this report. Applied studies are conducted in connection with the development and evaluation of new mining techniques, and the effective processing and utilization of coal and coal products. Analyses of coal, technical advice, and other assistance to Federal agencies in connection with fuel and boiler-water problems, and health and safety activities are among the practical services handled by the Bureau, Fundamental research such as that on coal structure and on the properties of coal is conducted because it will, over a period of the, furnish an increasing general knowledge about coal; scientists and engineers may use this knowledge in solving problems in mining and utilization of

Jan 1, 1963

By D. Janicijevic

This paper describes the process of scraper winch pull force measurement and shows the results of the actual winch pull force in extreme stall situations as well as during the face and gulley cleaning. It was found that by slowing down the motor and causing it to slip, torque up to 3.5 times higher than the nominal can be developed, resulting in the same increase of winch pull force. On the other hand, measurements of the actual force needed for cleaning of the face and the gully have shown that the currently used winches are too powerful. The extra torque that can be developed by the already too powerful winch motor poses a significant danger and necessitates the implementation of measures that will eliminate this risk.

Jan 1, 2008

By A. Mahmoudkhani

There has been a continuous interest in chemical aids for processing Canadian oil sands by hot water extraction process since the first commercial industry operation in 1967. Several inorganic and organic chemical systems have been introduced, of which sodium hydroxide is the most widely used extraction process aid by major producers. Use of NaOH, however, results in accumulation of sodium ions in recycled water, causing higher clays dispersion and producing tailings with poor geotechnical properties that turn into mature fine tailings. This is especially true for low grade and oxidized ores, which present the greatest challenges in bitumen recovery and produce the major portion of fine tailings. In this paper, we are presenting a novel method based on use of inorganic polymers as process aids for various low grade oil sands ores. Denver flotation cell and a laboratory scale hydrotransport loop were utilized to evaluate the effect of chemical dosage and operating parameters on the processability of oil sands samples from Athabasca region. Process tailings were examined for properties such as water chemistry, suspended solids, settling rate and the ease of tailing treatments. Our results demonstrate that the use of inorganic polymers during the froth process lead to a significant improvement in bitumen recovery from low grade oil sands and can improve further tailing treatments. This offers a viable solution that can be easily incorporated into current processing facilities and deliver several operational and economical benefits. Advantages in use of inorganic polymers versus sodium hydroxide are presented in details.

Jan 1, 2012

By J. O. Marsden

Over the past eight years, Phelps Dodge (a subsidiary of Freeport-McMoRan Copper & Gold, Inc.) devoted a significant amount of effort to the development of a suite of processes for the effective hydrometallurgical treatment of copper sulfide concentrates. This effort resulted in the development of high-temperature (>200ºC) and medium-temperature (150° to 165ºC) pressure leaching processes. Specific configurations of both processes have been commercially demonstrated at Phelps Dodge?s facility in Bagdad, Arizona. This paper reviews in detail the chemistry of medium-temperature pressure leaching of copper concentrates and reports on the process development work conducted by Phelps Dodge and others for this technology. This paper is Part I of a four-part series on this technology. Part II covers the development of medium-temperature pressure leaching and direct electrowinning technology; Part III considers the large-scale demonstration of the MT-DEW-SX process at Bagdad, Arizona; and Part IV addresses the development and design of a full-scale commercial application at Morenci, Arizona.

Jan 1, 2007

By D. A. Buckingham

Engineering and economic evaluations were performed by the Bureau of Mines on 14 Frasch sulfur, 1 native sulfur, and 21 metal sulfide operations in 11 market economy countries. The evaluation included discounted-cash-flow rate-of-return economic analyses at 15 pct to determine the average total cost of production of these two commodities and the potential availability of elemental sulfur (8) and pyrite concentrate. The Bureau evaluated the potential availability of elemental sulfur and pyrite concentrate. Approximately 279 million metric tons (Mmt) of pyrite concentrate at 46 pct 8 is potentially recoverable from 422 Mmt of in situ metal sulfide ore. Nearly 89 pct of the total pyrite concentrate is available at an average total cost of production below the January 1984 pyrite concentrate market price ($43/mt). About 185 Mmt 8 is potentially recoverable from 253 Mmt of in situ elemental sulfur. About 99 pct of this sulfur is available at an average total cost of production below its January 1984 market price ($131/mt).

Jan 1, 1986

Recovery of Rhenium from Mineral Raw Materials of Kazakhstan

Sep 13, 2010

By N. Niemuth

Strong demand for copper in developing nations such as China and India, plus the additional demand for industrial minerals to supply the Arizona construction market, brought about a record-setting year for the state?s mining industry. The value of Arizona?s copper production set a new high of $5.5 billion and pushed the total value of mineral production to $7.58 billion. This was also a record. As it has for many years, Arizona ranked first in nonfuel mineral production in the U.S. In addition to leading the nation in copper, Arizona ranked in the top five in molybdenum, sand and gravel, gemstones, perlite, silver, zeolites and pumice. Generally strong and rising prices, especially toward year?s end, fostered a bullish atmosphere that encouraged significant levels of acquisition and exploration. This activity has spread beyond the normal commodities to include some, such as manganese and fluorspar, that have not been mined in Arizona for decades.

Jan 1, 2008

By M. B. McClenaghan

"This paper summarizes diamond exploration techniques used in glaciated terrain, focussing on indicator mineral and geochemical methods applied to glacial sediments. Understanding the ice flow history, depositional history, and stratigraphy of glacial sediments is essential to successful sampling, interpretation and follow-up of indicator mineral and geochemical anomalies related to kimberlites. Kimberlite indicator minerals survive glacial transport over long distances and the relative abundance of each mineral in till is a function of the primary mineralogy of individual kimberlites. Indicator mineral distributions observed at a regional scale define the net effect of glacial dispersal, often along different ice flow directions. Local-scale distributions define individual dispersal trains. The medium sand (0.25 mm to 0.5 mm) fraction of heavy mineral concentrates, * GSC Contribution No. 2002028 prepared from glacial sediment samples, is best suited for indicator mineral surveys. The application of till geochemistry to diamond exploration is increasing because it is significantly cheaper than indicator mineral analysis and it can be performed quickly. The <0.063 mm (silt+clay) and 0.5 mm to 2.0 mm (coarse sand) fractions provide the best geochemical contrast between background and kimberlite-rich till. Kimberlite pathfinder elements that provide good contrast include Ni, Cr, Ba, Co, Sr, Rb, Nb, Mg, Ta, Ca, Fe, K, Ti and LREE, the relative importance of which will depend on kimberlite composition and that of the surrounding bedrock.IntroductionIn Canada, glacial erosion is the principal means by which kimberlite and its associated minerals have been dispersed, from a few tens of metres to tens of kilometres down-ice. Post-glacial weathering has had little impact on kimberlite debris in the glacial sediments, thus boulder tracing, indicator mineral methods and trace element geochemistry of the fine fraction of till (“drift prospecting” methods) can be used to detect kimberlite dispersal within areas covered by glacial sediment. This paper provides a summary of drift prospecting methods for kimberlite exploration in glaciated terrain, and includes examples of reconnaissance- , regional- and local-scale kimberlite indicator mineral and till geochemical distribution patterns.Weathered kimberlite is more susceptible to glacial erosion than the surrounding bedrock, thus many kimberlites in glaciated terrain are found in low or swampy ground, under small lakes, or covered by thin (< 1 m) to thick (>50 m) glacial sediments. Glacial erosion has removed varying amounts of the pre-glacially weathered kimberlite and, in some cases, the hard competent kimberlite below. For example, glacial erosion of the Peddie, McLean and Seed kimberlites near Lake Timiskaming, Ontario, removed pre-glacially weathered kimberlite, leaving a polished striated subcropping surface (McClenaghan et al., 1999a). In contrast, glacial erosion of the B30 kimberlite, near Kirkland Lake, Ontario (Fig.1), was much less vigorous and left a >10 m cap of soft and highly weathered dark green clay-rich kimberlite (McClenaghan et al., 1996). The thickness of remaining pre-glacially weathered kimberlite will influence the geophysical signature of the kimberlite."

Jan 1, 2002

By D. C. Kaliampakos, A. K. Moutsatsou, J. K. Skotaras

The wastes from marble extraction in the Thasos- Kavalla-Drama region of northeastern Greece could be utilised as a new source of high-quality white carbonate fillers for the European market. Large deposits, satisfactory properties, acceptable processing costs and environmental benefits are among the factors that would have a positive bearing on a proposal for their use in this way. DTH, the waste arising from dolomitic marble quarrying operations on the island of Thasos, appears to be the more suitable material than DA waste from Nikissiani on the mainland because of the lower cost of primary grinding and the higher production rate of ultrafines with a mean particle size of 5 micrometres (the optimum size for filler properties in the case of both DTH and DA), its superior whiteness, the benefits that such use would bring to a very severe and complex environmental problem and the lower transport cost

Jun 18, 1905

By D. Olsen, S. Cole, J. Strid, G. Colzani

This paper focuses on the underground tunnel work at the Hollywood Water Quality Improvement Project (HWQIP) in Los Angeles, CA. The HWQIP is being constructed to provide a water distribution system to bypass the existing Hollywood Reservoir System, which supplies drinking water for 500,000 people. The major project features include, a 2.9-meter diameter 1,829 meter long bypass tunnel, a 1.8-meterdiameter 366 meter long utility tunnel, 3 jack and bore tunnels, two 136 million liters underground circumferentially wrapped pre-stressed concrete water storage tanks, associated piping, and mechanical facilities. The physical project location coupled with strong community involvement and stringent environmental concerns was a considerable driving force for this project located in the Cahuenga Pass area of the Hollywood Hills north of Los Angeles, CA.

Jan 1, 2001

The captions to Figs. 1 and 2 of the paper by B. J. Parry entitled &apos;High-strength cold-rolled steels&apos; should read as follows:

Jan 1, 1984

By Douglas D. Donald

The New Jersey Zinc Co. successfully holed through a 2 1/2-mile haulage tunnel connecting its new Ivanhoe shaft with the Van Mater Shaft at Austinville, Va. This 8x 10-ft cross-section tunnel was driven from both ends and met at a point approximately a mile from one shaft and a mile and a half from the other. In order to make certain that the faces met accurately on line and grade it was necessary to refine conventional mine surveying practices. The mines that are serviced by these shafts are located in the southwestern part of Virginia approximately midway between Roanoke and Bristol at the west foot of the Blue Ridge. While the presence of lead-zinc sulfide ores has been known in this area for more than 200 years, it was in 1902 that New Jersey Zinc Co. acquired the Austinville property, which has been in constant operation since that time. About ten years ago the company undertook an extensive diamond drilling program at Ivanhoe several miles to the southwest. This program was successful in locating sufficient ore to justify the purchase of a number of the properties in this area and plans were made to develop the new orebodies. The discovery of this ore as well as substantial addi- tional reserves at Austinville resulted in a decision by the company to increase its daily milling capacity to 3000 tons, of which about 1000 tons would be supplied from the Ivanhoe mine. After careful consideration of all possible methods of transporting this volume of ore from Ivanhoe to the mill, it became evident that diesel locomotive haulage through a 2½-mile tunnel between the two mines would best suit prevailing conditions. Since the lowest operating level, known as the 1100 level, of each mine would be at approximately the same elevation, it was obvious that such a tunnel should be driven on this level. Not only would this tunnel facilitate feeding Ivanhoe ore into the underground crusher and skip loading installation at Austinville, but it would also open up a known orebody 5000 ft southwest of the Van Mater shaft. In addition it would provide a valuable diamond drilling base from which a large and a potentially favorable but untested block of ground might be explored. In order to hasten the completion of the tunnel, it was felt that it should be driven from both ends. ENGINEERING CONTROL PROCEDURES It was vital that the tunnel junction be made accurately on line and grade; thus it was felt that engineering control of an unusually high degree of reliability was required to prevent an accumulation

Jan 1, 1959

By James W. Stewart, A. C. Colvine

Introduction Precambrian shield terrains the world over are experiencing an unprecedented level of concerted exploration for lode gold deposits. Reasons for this include: • The increase in the price of gold (following 40 years at $1.13/g or $35 per oz) has transformed targets that were once unattractive into viable exploration propositions. • The relatively suppressed market for other metals produced from shields (base metals, nickel, iron, and uranium) has further focused exploration attention on gold. • The preeminence of gold production from rocks of early Precambrian age, as shown in Fig. 1. • The relatively high grade of gold in these mines (averaging about 10 Wt or 0.29 oz per st) permits profitable extraction even under depressed gold prices. A number of these mines have been in continuous operation for more than 50 years. • The recent discovery of the major Hemlo deposit, in well exposed rocks adjacent to the Trans Canada Highway, has had a world-wide impact. This demonstrates that a major new deposit can be found even in an accessible, well exposed area of a shield; gold mineralization is susceptible to rational exploration; and new target types for gold exploration exist. This paper reviews exploration activity for gold in shield terrains worldwide (Fig. 2), excluding Early Proterozoic paleoplacers of the Witwatersrand type. Emphasis is on the Archean, which is traditionally the most productive part of the Precambrian shields. There is also an emphasis on the Canadian shield (Fig. 3) because of its vast areal extent and exceptionally broad range of mineralization styles. Geological Approach A basic problem exists in gold exploration when compared to exploration for base metal massive sulfides that predominated during the 1960s and 1970s. Gold concentrations cannot usually be detected by airborne geophysical instruments. The majority of massive sulfide deposits were detected using airborne electromagnetic detectors and magnetometers. A full 75% of Canadian gold discoveries can be credited to surface prospecting. The percentage is even higher in other countries. This observation allows for great optimism for two reasons: • Large areas of shield terrain are obscured by either surficial deposits (glacial tills, clays, and desert sands) or deep surface weathering. This makes them inaccessible to prospectors. Logic dictates that such obscured areas should have the same potential for gold concentration as has exposed bedrock. • The Hemlo style of mineralization, a roughly tabular ore body where gold is associated with disseminated sulfides, is different from the traditional prospecting target. The gold is hosted by discrete quartz veins. While it is true that limited discoveries were made at Hemlo more than 30 years ago, and this style of mineralization is present elsewhere, recent

Jan 12, 1984