Search Documents

By G. R. Hopkins

For several years prior to about the middle of 1928 both the number and capacity of natural-gasoline plants showed a steady increase; this resulted from a material gain in the supply of casinghead has due to the discovery of a number of flush fields with relatively high gas-oil ratios. From 1928 to date some form of proration has been continually in force, with a consequent curtailment in the supply of wet gas. This decline in available gas and a severe decrease in prices, due largely to the increasing competition of light refinery products, has eliminated virtually all of the weaker units during the last 5 years, with the result that the number of plants declined from 1,155 on January 1, 1928 to 19035 on January 1, 1930, to 909 on January 1, 1932, and then to 859 on January 1, 1934, The struggle of the small high-cost producers to exist is illustrated further by the trend in the number of shut-down plants, which has increased from 36 on January 1, 1930 to 100 on January 1, 1932 and to 128 on January 1, 1934. The increase in the number of plants prior to 1929 resulted in a material gain in the total capacity, but the decline in number between 1929 and 1932 was not followed by a corresponding decrease in capacity, as gains resulting from the construction of a few very large plants overbalanced the loss due to the dismantling of a large number of small ones. However, the low prices of 1932 and 1933 supplied little incentive for new construction, and the total capacity declined in approximately the same ratio as the number. Thus the total capacity declined from 11,387,000 gallons daily on January 1, 1932 to 13,060,000 gallons daily on January 1, 1934, Of the latter 9,181,000 gallons (91 percent) represented the capacity of the operating plants and 679,000 gallons (9 percent) the capacity of the idle plants.

Jan 1, 1934

By R. W. Courtney

The objective of this study is to make a critical evaluation of the magnitude and extent of electrostatic hazards in typical U.S. mining operations and to assess the adequacy of techniques, materials, and equipment for detecting and minimizing these hazards. This was accomplished with an incident/accident survey, mine visits, literature search, and engineering analysis. It was concluded that it would be desirable to (1) utilize ground fault interrupters to minimize stray current from electrical utilities, (2) decrease the current and electrostatic sensitivity of electric detonators used in areas with a high incidence of lightning strikes or troublesome stray currents, (3) institute quality control and test standards for blasting material and protective devices, (4) establish an electrostatic monitoring program for loading ANFO in plastic lined holes, and (5) establish a risk criteria for operator exposure in mines.

Jan 1, 1982

By AIME AIME

T HE 133rd meeting of the A. I. M. E., opening in New York on Feb. 15, promises to be as successful technically and socially as any in the past. The papers submitted for the various technical sessions are unusually excellent and insure something of interest to every group. Tentative programs have already been issued, and a concise resume of the various sessions, arranged chronologically, appears on page 48. Among the many interesting technical sessions arranged, attention is directed to those of the Petroleum Division, embracing the Symposium on Production that has come to be an annual feature, and new ones on refining practice, transportation and economics. The Institute of Metals program is similarly comprehensive. It includes 15 papers, 8 on copper, 4 on aluminum and its alloys, and one each on magnesium, lead, and fatigue of metals. The Coal Committee offers as a leading contribution its report, prepared under the direction of H. N. Eavenson, giving a new analysis of the capacity of the mines and a comparison of coal with other industries. This will be supplemented by a number of other papers of especial interest to operating men, among which are "Data on Use of Loading Machines in Bituminous Mines," by Graham Bright; "Evaluation of Coal," by R. H. Sweetser; "Selection of Coals for the Manufacture of Coke," by H. J. Rose; and "Relation of Origin and State of Carbonization of Coal to Problems of Low Temperature Carbonization," by S. W. Parr. The Iron and Steel Committee has scheduled seven papers, and there will be a special session on open-hearth practice, in which will be presented the first results of the two conferences, held by the sub- committee at Pittsburgh and Cleveland. A symposium on molding sands will be a special feature of the session on non-metallics.

Jan 1, 1926

Casing or lining pipe is used in boreholes for the following reasons:1. To preserve the hole while drilling and after it is finished.2. To shut water out of the hole or to isolate any particular water, gas, or oil-bearing stratum.Deep holes can seldom be drilled without casing, and only when in firm strata. If caving from the walls is at all likely while drilling, casing is necessary in order to prevent the tools horn being buried...

Jan 1, 1924

By J. H. McKibbon

THE metallurgical industry has purchased more than sixty per cent of the industrial gas cleaning equipment installed in Canada. This includes cyclonic collectors, scrubbers, cloth filters and Cottrell Precipitators. These are the principal types of equipment which are used commercially for the cleaning of gases which result from the processing of iron, nickel, copper, lead, zinc, gold, gypsum and aluminum ores. The recovered dust, which usually contains metal values, is returned to the process. The cost of the equipment is thus economically justified. This is in contrast to other industries, such as those involving steam power generation, asbestos, cement and lime production, where, though dust collection equipment is extensively used, it is installed primarily for nuisance abatement. Communities are becoming more and more conscious of air pollution, new and more stringent legislation is being enacted, and, for other than economic reasons the smelting industry will eventually be required to install more efficient gas cleaning equipment. This paper

Jan 1, 1962

Aluminum Production. -By October 1, Aluminum Company of America will restart a 35,000-ton-per-year unit at its aluminum smelter at Rockdale, Tex., restoring that facility to its full capacity of 325,000 tons annually. Primary Ingot Price Increase. -Most U.S. aluminum producers in mid-September were quoting a price of 72 cents per pound for primary aluminum ingot. On September 19, Kaiser Aluminum & Chemical Corp. announced that it would increase the price of primary aluminum ingot 4 cents to 76 cents per pound.

Jan 1, 1980

By Edwin G. Sharp, Frank S. Gaunce, George M. Freeman, Denis J. Kemp, Eric Dulson, Paul Salmon, Ernest R. Hamilton, Carl E. Parden

"THE ECSTALL ZINC PLANT was built for the treatment of the Kidd Creek zinc sulphide concentrates. Construction proceeded throughout 1970-71, with operations beginning in April 1972. The two concentrate types treated differ principally in minor impurity and precious metal contents. Processing flexibility was required to allow efficient recovery of the by-products, especially cadmium, copper and silver. The conversion of the zinc sulphide concentrates to end products follows a sequence of operations that are common to most electrolytic zinc plants and typical of the ""Tainton- Jephson"" flowsheet.1. Roasting in air at an elevated temperature to convert the metal sulphides to soluble metal oxides (calcine) and sulphur dioxide. The sulphur dioxide is converted to sulphuric acid in a contad plant and shipped by train to market.2. Leaching of the calcine in spent electrolyte to effect extraction and recovery of zinc as zinc sulphate solution, leaving an insoluble residue.3. Purification of the clarified zinc sulphate solution by cementation with metallic zinc dust to remove impurities detrimental to the electro-deposition of zinc or detrimental to product purity. The solids from cementation are the starting materials for secondary metal recovery.4. Electrolysis of the purified zinc sulphate solution to reduce the zinc to the metallic state while coincidentally regenerating the sulphuric acid for recycle to the leaching step."

Jan 1, 1974

By D. M. Ziebarth

"During the mid to late 1960s, the underground potash industry in Saskatchewan was born. For the next four decades the industry operated at a steady pace, supporting a large part of the world demand, until 2008 when the potash market heightened. Operators were motivated to capitalize on this increased demand, new mines were proposed while existing mines were planning upgrades. Potash Corp. of Saskatchewan (PCS) was one of the major producers planning upgrades to its production facilities quickly, including modifying the existing headframe and shaft at the PCS Cory Site to accommodate a new 1.5-kt/h (1,650-stph) hoisting plant. Upon completion of the project, the innovative operations group continuously reviewed methods to increase production and reduce operating costs, allowing PCS to continue being competitive on the world market.BackgroundPotash production is a major Saskatchewan industry and has played a significant role in the economy for more than 40 years. Production commenced in 1962 when water problems were overcome at the International Minerals and Chemical (IMC) Mine near Esterhazy, Saskatchewan. A surge of development by other companies resulted in 12 companies opening 10 mines by 1970. In 1975, Potash Corp. of Saskatchewan was created by the government of Saskatchewan, and shortly thereafter purchased several mines in Saskatchewan, including the Cory Mine, near Saskatoon.Cory has been in operation since 1968 and is located 12 km (7.5 miles) west of Saskatoon in central Saskatchewan. The mine is located in the center of the world’s largest potash deposit, 1,000 m (3,300 ft) below surface.PCS has embarked on sizable capital expansions of more than CDN$7 billion.The $1.6-billion Cory expansion was expected to raise operational capability of the site to 2.7 Mt/a (3 million stpy), an increase of 1.9 Mt/a (2.1 million stpy). To achieve 2.7 Mt/a (3 million stpy) of finished product and considering the 22.6 percent average production recovery (Potash Corp, 2013), 12 Mt/a (13.2 million stpy) of ore must be hoisted to the surface for processing. To deliver this rate required upgrading of the hoisting plant to 1.5 kt/h (1,650 stph). To accomplish this ambitious challenge, creative thinking, careful planning and a cohesive team was needed to work together to ensure the schedule, budget and most importantly that the work was completed safely (Potash Corp., 2013)."

Apr 1, 2017

By John R. Duda

The Bureau of Mines is developing estimates of capital investment, operating cost, and selling price for underground mines producing bituminous coal by various mining methods. This study estimates the required capital investment, operating costs, and selling prices for two hypothetical mines designed to produce 1.3 and 2.6 million tons per year (MM tpy)3 by using a longwall system in conjunction with a continuous-mining system. The coal properties being mined are assumed capable of sustaining a 20-year production period. Wages and union welfare payments used in this study are those in effect as of December 6, 1975, as set forth under the National Bituminous Coal Wage Agreement of 1974. Costs of materials and equipment are based on January 1976 indexes. Initial capital investment is $34.6 million for the 1.3-MM-tpy mine and $63.5 million for the 2.6-MM-tpy mine. Capital requirements, including deferred investments, were estimated to be $50.8 and $92.2 million, respectively. These figures translate into total capital investments of $38.51 and $34.91 per ton of annual production. Assuming a desired 15-percent discounted cash flow (DCF) rate of return, with Federal income taxes at 50 percent, the required selling prices would be $13.41 and $12.27 per ton for the 1.3- and 2.6 -MM- tpy mines.

Jan 1, 1976

By J. B. Zadra

Tungsten, a comparatively new metal, is one of the important strategic war materials. In peacetime, tungsten is widely used as a filament in elec¬tric lamps and electronic tubes and is a vital constituent of some of the most important industrial alloys. High-speed tool steel containing tungsten and stellite alloys containing cobalt, chromium, and tungsten are extremely hard and resistant to corrosion. These alloys and the tungsten carbides are unequaled as cutting tools and in other wear-resistant applications. They play a prominent role in the present era of mass production. Alloys containing tungsten resist oxidation at high temperatures and have been key alloys in the development of modern aircraft. The adaptability of tungsten to new uses is expanding, particularly in the high-temperature range. Domestic production of tungsten has come from a large number of deposits in 17 of the 49 States; but, of the total domestic output from 1900 to 1956, more than 80 percent was produced from mines in North Carolina, California, Colorado, and Nevada. The average tenor of the mined ore was less than 1 percent tungsten trioxide (W03).

Jan 1, 1959

By Joan Weinberg

Real gross national produce (GNP) grew at a seasonally adjusted annual rate of 2.0% in the fourth quarter (table 1). The restrained quarterly growth rate was the slowest in 2 years, and was substantially slower than the 2.5 % rate of the previous quarter. According to the U.S. Department of Commerce, the summer drought reduced the fourth-quarter growth rate by 1.1 percentage points. A growing trade deficit and a reduction in business investment were the key economic factors curtailing growth. The trade deficit widened by $6.8 billion, reflecting both a surge of imports and a slowing of exports. Business investment declined 3.7%, mainly as a result of a slowdown in computer sales. On a year-to-year basis, the economy grew at an inflation-adjusted rate of 3.8% for 1988, the fastest in 4 years, despite the drought. However, on a fourth-quarter-to-fourth-quarter basis, real growth measured 2.7%. Increased exports and business spending for plant and equipment accounted for much of the 1988 GNP growth. Employment continued to grow as the manufacturing sector added 414,000 new workers (table 2). Of these, the primary metals industry added 26,000 workers, and the clay, glass, and stone industry added 10,000. The civilian unemployment rate remained low throughout 1988, fluctuating between 5.3% and 5.4% during the last quarter.

Jan 1, 1989

By Greisson Peixoto Rangel

A variação da resistência à compressão de argamassas geopoliméricas foi estudada em função da razão ativador/precursor e da molaridade da solução ativadora. As argamassas estudadas foram confeccionadas com metacaulim (precursor) ativado com solução composta por hidróxido de potássio e água destilada, e areia normal brasileira. De acordo com os resultados, a resistência aumenta com a diminuição da razão ativador/precursor e com o aumento da molaridade da solução ativadora. Além disso, os valores encontrados condizem com os presentes da literatura e com possíveis aplicações para argamassas de múltiplo uso.

Oct 30, 2017

By Sidney Katell

This report, covering the period January 1969 through December 1969, is a continuation of a series that began with the publication of Information Circular 7516 in October 1949. It is the 11th in a series of reports prepared in cooperation with the American Association of Cost Engineers. The abstracted articles are concerned with all phases of cost engineering in the field of chemical and petroleum plants and related subjects. They are from the following sources: 1. American Association of Cost. Engineers Bulletin. 2. Bureau of Mines Information Circulars. 3. Bureau of Mines Reports of Investigations. 4. Chemical Engineering. 5. Chemical Engineering Progress. 6. Chemical Week. 7. Coal Age. 8. Coal Mining and Processing.

Jan 1, 1970

Discussion of the paper of R. J. COLONY, presented at the New York Meeting, February, 1921, and issued With MINING AND METALLURGY No. 169, January, 1921. R. J. COLONY (author's reply to discussion).-The work of Sosman and Merwin on the system lime-ferric oxide, mentioned by Mr. Rankin, was not overlooked. When studying portland cements and portland-cement clinkers petrographically, however, the lime-iron compound was difficult to correlate with the very definite dicalcium ferrite described by those investigators, which possesses such well-defined optical properties. In portland cements, the calcium ferrite (or ferrate?) is an indefinite, fuzzy, and generally amorphous, or apparently amorphous substance that is distributed interstitially with respect to the other grains, from which it was very difficult to derive any satisfactory results. For this reason, the writer, tentatively, chose to regard it as related to the aluminate, and assigned to it the composition 3CaO.Fe203, which may be incorrect, however, as Mr. Rankin suggests.

Jan 8, 1921

By D. F. Malan

This paper provides an overview of the concepts of citations and journal impact factors, and the implications of these metrics for the Journal of the Southern African Institute of Mining and Metallurgy (JSAIMM). Two key research literature databases publish journal impact factors; namely, Web of Science and Scopus. Different equations are used to calculate journal impact factors and care should be exercised when comparing different journals. The JSAIMM has a low impact factor compared with some of the more prestigious journals. It nevertheless compares well with journals serving other mining sectors, such as the Canadian CIM Journal. The problems associated with journal impact factors are discussed. These include questionable editorial practices, the negative impact of this concept on good research, and the problem of a few highly cited papers distorting the journal impact factor. As a consequence, there is growing resistance to the use of journal impact factors to measure research excellence. The San Francisco Declaration on Research Assessment is a global movement striving for an alternative assessment of research quality. As a recommendation, the Editorial Board of the JSAIMM should adopt a pragmatic approach and not alter good journal policies simply to increase the journal impact factor. The focus should remain on publishing excellent quality papers. Marketing of the Journal, the quality of the published papers, and its open access policy should be used to counter the perception that journals with high impact factors are better options in which to publish good research material.

Sep 1, 2022

By Cory G. Rice

A significant portion of the piling industry has long felt relying on soil setup to gain the required capacity is a complexity that would rather not be dealt with. Instead, the pile are driven to the required capacity on the initial drive and the potential gain of capacity due to soil setup is simply considered an added bonus or safety factor. There appears to be an attitude that if one did not put in the energy required to develop the full capacity on the initial drive, then one should not expect to gain anything from Mother Nature for free. However, substantial savings in time and materials can be realized by properly accounting for setup. This paper will show the impacts and ramifications this rationale can have on required labor and material costs and illustrate a case history with significant soil setup and the savings realized on a project currently being constructed.

Jan 1, 1992

By E. S. Moore

"The Centre of the silver-producing section of the Gowganda area lies about 55 miles northwest of Cobalt, and the village of Gowganda is 71 miles by road from New Liskeard. The geological similarities of the Gowganda and Cobalt areas led prospectors westward from the rich Cobalt field, first to Elk Lake and then on to Gowganda, where mineralization was found in 1907. A year later many showings were found, and rich hand-picked ore was shipped. Most of the ore has come, however, from two mines, both of which are still operating; the Miller Lake-O'Brien, which was purchased by Siscoe Metals of Ontario Ltd. in 1945, and the Castle-Trethewey. The annual production of these two mines runs over one and one-half million ounces of silver and considerable cobalt. The total production of the camp has reached about 32,000,000 ounces of silver and a large amount of cobalt, the total not recorded.General GeologyThe general geology of Gowganda is in many respects much like that of Cobalt. There are areas of Keewatin basic and acid Javas mixed with tuffs and basic intrusions. These rocks are deformed and partly altered to schists, and have been intruded by some Haileyburian basic and ultra-basic rocks and by Algoman granite. These were followed by a large number of porphyritic Matachewan quartz diabase dykes. After a period of extensive erosion the Huronian sediments were deposited on a pene-planed surface over all the older rocks; these sediments include large quantities of conglomerate (partly tillite), quartzite, and greywacke. The Keweenawan rocks include the Nipissing quartz diabase sill, later quartz diabase dykes, and one long olivine diabase dyke, the latest Precambrian rock. The area has been extensively glaciated.Structural FeaturesThere has been little folding in the area since the Algoman batholiths were intruded, and the Huronian sediments lie nearly flat, with dips of 10, 15, or rarely 25 degrees. The Matachewan dykes show a remarkably uniform, nearly north strike, indicative of east-west tension when they were intruded. On the other hand, the dykes later than the sill strike nearly east, tangentially to the northeasterly and northwesterly strikes of the Miller Lake basin."

Jan 1, 1949

By Willie M. NeSmith, W. Morgan NeSmith, Alan Roach

"In 2013, Augered Cast-in-Place (ACIP) piles are a mature foundation technology throughout the United States. General guidelines for the design and construction of ACIP piles are available along with numerous references for design in specific North American geologies. In fact, the current generation of contractors and geotechnical practitioners might view ACIP piles as just another deep foundation option to be considered, along with driven piles, drilled shafts and others. This acceptance has developed, however, over a 60-plus year period.The term, Augered Pressure-Grouted (APG) pile is often used when referring to ACIP piles because the piles emerged out of construction processes at the Intrusion-Prepakt firm in the late 1940s. The company’s specialty was pressure grouting and preplaced aggregate concrete. The grouting was typically accomplished by driving a pipe to a target level and then injecting grout under pressure. In some soil conditions, it was necessary to use an auger to reach the desired grouting depth. In these circumstances, the grout pipe was driven beside the auger and grout was pumped as the auger was withdrawn. The grout pipe was then withdrawn as well. This was the genesis of the APG, or ACIP pile, and many piles were installed using this technique. The patent application, “Method for Forming Piles” was filed by Raymond Patterson of Intrusion-Prepakt in 1951, and the patent was granted in 1956. The process was eventually modified when a suitable hollow-stem auger was developed. Licenses were granted to the Lee Turzillo Contracting Company and Berkel & Company Contractors, Inc. in the late 1950s. Each of the three companies Patent, LicensesThe patent application, “Method for Forming Piles” was filed by Raymond Patterson of Intrusion-Prepakt in 1951, and the patent was granted in 1956. The process was eventually modified when a suitable hollow-stem auger was developed. Licenses were granted to the Lee Turzillo Contracting Company and Berkel & Company Contractors, Inc. in the late 1950s. Each of the three companies coined their own terms for the piling process: “Pakt-In-Place” for Intrusion-Prepakt, “Auger Pressure-Grouted” for Berkel and “Augercast” for Turzillo. Over time, “Augercast” was frequently used as a generic term for the system. The installation of these piles was, and still is, a highly nuanced process; “contractor dependent” is a term often seen today. Intrusion-Prepakt, Berkel and Turzillo all had personnel who were part of the original group that developed the system and who appreciated the craftsmanship involved in forming sound piles."

Jan 1, 2013

By Norman L. Wimmler

Active placer mining in Alaska began near Juneau in 1880, but the first gold rush did not start until 1896; then the discovery of the Klondike brought gold seekers from all parts of the world. A few of the newcomers were experienced miners, but the majority knew nothing whatever of placer mining. Even those who were placer miners of much experience found entirely new conditions, notably frozen ground, that presented many difficult problems. As a result, numerous methods of mining and of thawing frozen ground were tried. From these trials the practice described in this bulletin has been developed. All known placer fields in Alaska have been mined to some extent, and some have been virtually exhausted. In most districts, however, there remain large quantities of low-grade gravel and also some small isolated areas of comparatively rich gravels which could not be successfully mined because of adverse physical conditions. These districts are now the scene of most placer mining, including dredging, hydraulicking, drifting, mechanical methods of open-cut mining, and ground sluicing (or booming) followed by " shoveling-in."

Jan 1, 1927

By Juan J. Monsalve, AMAN SONI, Nino Ripepi, Richard Bishop

The design and strength of pillars are important parameters when implementing the room-and-pillar mining method in a limestone mine. The process becomes complex with the presence of karst voids, which are frequent phenomena in carbonate rock formations. This research continues a previous study aimed at studying the effect of karst voids on the strength of a particular limestone pillar. Using calculated pillar strength and estimated redistributed stresses, it was assessed that the pillar can counter more stress than currently imparted on it. Numerical modeling studies combining in situ stress determination and excavation sequencing were used to estimate the existing stresses on the pillar. Different possibilities of modification to existing pillar design were simulated using distinct element method (DEM) modeling to determine a better design.

Jun 1, 2023