Search Documents

By Stephen J. Roberts

Gold catalysts were prepared on co-precipitated, calcined copper oxide - zinc oxide support by an inverse deposition-precipitation method. These catalysts were characterised by X-ray diffraction (XRD) and temperature-programmed reduction (TPR) and studied for CO oxidation activity at various catalyst calcination temperatures. TPR studies of the support material exhibited a double peak and shift to lower temperatures for the reduction of Cux+ to metallic copper, as opposed to the single reduction peak for pure CuO. This phenomenon is possibly caused by an interaction with the zinc oxide. The addition of gold to the support CuOZnO led to a further shift in copper reducibility to lower temperatures. Gold present in the initial uncalcined catalyst as Au3+ was auto-reduced to Au0 under various calcination temperatures. The Au3+ reduction peak was observed to shift to lower temperatures with increasing calcination temperature. The catalytic activity was found to pass through a minimum value with respect to calcination temperature. Catalysts with both gold in entirely the 3+ or metallic oxidation state were found to exhibit high activity. Furthermore, the catalysts were found to decrease in activity with decreasing Au3+ content up to an intermediate calcination temperature, afterwhich the activity increased sharply. Possibly at higher temperatures, a stronger Au-support interaction is formed, leading to a new active site.

Oct 1, 2003

By Yeruva Ramanareddy, Sohail Wajid, Ahmed Shaz, K. Bhavani

"CP-06 is an NATM cross passage which connects up-line and down-line metro tunnels near Kilpauk Medical College, Chennai. It lies completely in loose silty sand to dense sand with water table almost touching the ground surface after Chennai floods. Pre-grouting was done before excavation to seal the area and to ensure no-loose pockets. The heading was excavated successfully but while benching excavation huge water ingress started seeping out. Sand also permeated along with water which became unstoppable due to cavity formation and caused the up-line tunnel to sink considerably. A large grouting exercise was carried out with different grout materials and techniques both from the ground surface and inside of tunnel to stop the water ingress and stabilize the tunnel. This paper describes the chronology of events that occurred in the tunnel during CP-06 issue. It elaborates all the different grouting techniques involved in the whole process of the tunnel stabilization. It includes a finite element analysis using Rocscience RS2 9.0 software showing the possible cause of sand incursion with water from the CP invert which lead to the tunnel settlement. This paper also describes the after effects and the lesson learnt from the whole incident.INTRODUCTIONConstruction of Metro Rails has become the latest alternative to cope up with the transportation demand of the growing urban cities population. L&T SUCG JV constructed Chennai Rail Metro Phase II Contract UAA-04 which included design and construction of approximately 4 km of route length of underground mass transit railway including 3 underground stations. This package also includes 12 cross passages which are NATM tunnels connecting upline and down-line side of TBM tunnel for safe evacuation of passengers in case of emergency. As per NFPA guidelines, this is a mandatory structure and there should be atleast one cross passage in 244m tunnel length.CP-06 is a cross passage connecting upline and downline tunnel between Pachiyappa College Station and KMC Station, in Chennai Metro. During the construction of CP-06, heavy water seepage of around 450 liters per minute was encountered during second round of benching excavation after full heading was excavated. An inflow of around 12-15 cum of sand and silt was also observed inside the tunnel along with the seepage water, which created piping inside the TBM tunnel causing it to settle continuously with time. A huge effort was made to stop the water ingress along with loose sand which was causing the running tunnel to settle, involving all possible grouting methods and temporary support installation."

Jan 1, 2017

Geotechnical input is interwoven into the mining process at George Fisher South Mine from the planning and design of working areas to the closure of worked out areas and maintenance of life of mine and long term excavations. The methodology used consists of a mixture of application of established theoretical principles and guidelines derived from successful historical experience. In the development stage, including long term infrastructure excavations, the process takes into account the expected life of the excavation, usage and expected stress changes during its life span. On the stoping stage, the design process takes into account the local rock mass conditions, geological structure setting and previous experience in a particular orebody. Due to the high variation in age of currently used excavations, a rolling monitoring and risk assessment process for long term and life of mine excavations and infrastructure is maintained. This paper has as an output the process that must be followed to ensure an excavation on the highly dynamic mining environment at George Fisher South Mine is blasted and maintained in compliance with applicably commonly accepted safety and industry requirements.

Nov 25, 2010

By John B. Sabey, Vernon R. Degner

The industrial coal processing trend toward greater fines production, due to mining techniques and customer requirements for reduced ash and sulphur content in the fine coal product, is the basis for ongoing efforts to improve the performance of the flotation machine. WCO has successfully adapted the principles of the beds Column to a full size machine prototype. Recent plant evaluation tests confirmed the initial promise of this concept by achieving a considerably lower ash product while maintaining the combustible recovery level of conventional flotation machinery. The paper will include a review of the fundamental principles of the beds Column concept, together with a summary of the WEMCO R&D Program from concept evaluation and laboratory testing, through pilot, to full size machine tests. The performance of the WEMCO/Leeds flotation column will be compared to conventional flotation concepts using a flotation "kinetics" approach, which quantifies the floatable and non-floatable specie recovery performance using the Klimpel model as the basis for analysis. The variety of distinct features unique to this concept include a series of barrier rods which are used to advantage, often together with countercurrent reflux water flow, to achieve a significant improvement in product grade. The hydrodynamics associated with the mechanics of "gangue stripping" from the rising "air bubble-floatable specie" matrix will be briefly reviewed.

Jan 1, 1988

A systematic study of groundwater conditions at eight underground mine sites exhibiting a wide range of groundwater qualities throughout Australia has been completed at the WA School of Mines. This has resulted in a new corrosivity classification for groundwater driven corrosion processes for cement grouted cable strand used in the Australian underground mining industry. The new corrosivity classification is simple to use and corrosion rates may be predicted from readily obtained in situ measurements of groundwater dissolved oxygen.

Jan 1, 2008

By T. R. Ellis

Many appraisers/valuers believe that the only valuation method available within the Cost Approach category for Real Property appraisal is the depreciated replacement cost method. Some valuation and financial reporting standards setters also believe the same. This paper introduces the minerals appraiser to a number of useful methods for mineral property appraisal that are based primarily on the principle of contribution to value, the predominant economic principle in the cost approach. Most of these cost approach methods discussed are primarily for use in valuation of exploration tracts and resource properties that have no defined reserves. However, the powerful rural cost method can be used to calculate the contribution of categories of resources, reserves, and other property components to the value of a mineral property. This method can be applied to mineral properties at all stages of development, including producing properties.

Jan 1, 2011

By Sunil Koppalkar, Liming Huang

"Since late 1980s the research group led by late Professor Andre Robert Laplante at McGill University undertook fundamental studies and applied research of the Knelson Concentrator (KC) and developed a sustainable method to correctly estimate gravity recoverable gold (GRG). In the early time a concept of ‘free gold’ was used, it was defined as the gold that could be separated and recovered from gold ore by amalgamation. Due to health and safety hazards, its practical use had declined. Around 1994, a methodology using a 3-in Knelson Concentrator to measure gravity recoverable gold was established at McGill University. Through more than 10 years’ improvement and optimization, this technique had become a standard method to evaluate GRG for gold ores, gold plant streams and platinum group metals. Until 2006, about 200 GRG tests had been carried out at McGill University for the ores from all over the world. Recently, a modified version of GRG test (short test) with the advantages of reduced processing time and lower cost had been developed for the mundane needs of gold industry.INTRODUCTIONGold gravity recovery has evolved significantly over the past twenty-five years, mainly because of the advent of the Knelson Concentrator (Knelson 1988, 1990, 1992, Laplante 2000). Now, a series of Knelson Concentrators for different applications are manufactured and used in gold industry all over the world (Knelson Concentrators 2004).In 1980s the Knelson Concentrator gained acceptance from mining industry as an effective device for the recovery of gold from grinding circuit. Knelson Concentrator became the obvious choice because of its design features: a relatively long processing time without concentrate discharge (compared to some other centrifuges, such as Falcon Concentrator and Chinese Yunxi Centrifuge at that time), large throughput capacity, treating a wide size range of material, yielding a high grade concentrate with small mass that could easily be smelted. As more and more Knelson Concentrators were accepted in gold industry, mineral processing engineers faced with challenges: what are the separation mechanisms of the Knelson Concentrator? How much gold can be extracted for an ore if a Knelson Concentrator is installed? For answering these questions, a laboratory scale Knelson Concentrator was created."

Jan 1, 2007

By Jan Pru?ka

This paper describes the sheet pile design for the Line C extension from Ládví station to the North of Prague. The first part of the paper describes the geological conditions and structural configuration of the project. Typical cross sections, the description of the construction stages, and monitoring are discussed. The second part of the paper focuses on the sheeting design method. It describes the method of dependent pressures, that is, how the pressures acting upon a structure depend on the deformation. The design process and verification methodology are described in detail with comparison of the results with in-situ monitoring.

Jan 1, 2011

By Jozef F. Zurawski

Increasingly new interceptors or new Combined Sewer Overflow (CSO) projects require connections to existing tunnels. More often than not, the existing facilities are old, in poor or questionable conditions, without proper construction records or as-built drawings. Many cannot be easily inspected unless major construction effort provides flow by-pass for safe access. This paper provides general guidelines on how to approach the problem of assessing the condition of old tunnels, how to plan and design the connection with limited physical assessment, how to develop the scope of work for the bid documents and how to provide geotechnical guidelines and designs for the bid documents.

Jan 1, 2008

By Martin Nevens

"In 1998, the Iron Ore Company of Canada initiated an aggressive program to improve the performance of its Carol Lake Concentrator located in Labrador City, Newfoundland. This program was termed the Concentrator Upgrade Program. The Concentrator Upgrade Program was a group of initiatives developed with the common goal of improving the overall process and operations of the IOCC Carol Lake Concentrator. The main goal of the program was to increase the annual production capacity of the concentrator from 18.0 million tomes to 21.6 million tomes. This gain in capacity was to be done mainly through improvements in process iron recovery. The target iron recovery value was 80+% versus a historical value of 70%. This improvement in iron recovery would translate to a natural weight recovery improvement from 44% to 50%.The Concentrator Upgrade Program provided the first opportunity in 30 years to make fimdamental changes to the concentrator flowsheet. To accomplish this, several pilot plants were built to evaluate new circuits. AAer 2 years, a new flowsheet was selected for the primary gravity separation circuit and the magnetite circuit. The centrepiece of the new flowsheet was the introduction of Hindered Settling Separators to the metallurgical process.The Concentrator Upgrade Program has since proceeded into detailed engineering and, as of February 2001, construction. The first one of IOCC’s 3 primary AG Mills (Mill 11) has been converted to the new flowsheet at the time of writing and is in the throes of commissioning. This paper will review the flowsheet development program in the pilot plant for the gravity separation circuit and examine the overall benefits to the operation of the IOCC Carol Lake Concentrator."

Jan 1, 2002

By Jeremy P. Doolan, Leigh B. Neindorf, Geoff W. Capes

The development and use of rock mass classification tools have been a key component for improving stope design over the past 4 years at the Xstrata Zinc George Fisher Mine in northern Queensland, Australia. In 2003, stope extraction data from 3 years of open-stope mining provided an excellent situation to review the assumptions in the feasibility study. Extracted stope profile information, drillhole geotechnical data, underground observations, and oral and written communication were used to develop a thorough stope reconciliation performance database. With-out collecting the back analysis data and presenting the data in a usable format, engineers are left to debate opinion instead of engineered judgment. This can lead to biased and uninformed design parameter choices with the potential to repeat poor design. This paper demonstrates some effective, practical examples of empirical data collection where rock mass classifications tools were developed and used to create improved confidence in predicting stope stability and failure profiles. The work contributed to design changes that resulted in a reduction in stope hangingwall dilution and an increase in head grade while continuing to ramp up production from 2003–2005.

Jan 5, 2007

By EDGAR K. SOPER, Clarence A. Wright, DOUGLAS C. LIVINGSTON, Thomas Varley

In 1917 the Federal Bureau of Mines and the University of Idaho arranged to cooperate in an investigation looking to the improvement of mining and milling methods in the mining districts of the State of Idaho, with an especial view to the wider development of the minerul deposits and greater efficiency in the treatment of the lowgrade ores of the State. This work has been made possible lnrgely through the generosity and active assistance of the mine operators, especially certain companies in the Coeur d'Alene region. As the first step in the work under the cooperative agreement it wa.s decided to gather all data possible on the various mining districts throughout the State, both active and abandoned, in order to ascertain their potential possibilities, especial attention being paid to methods of metallurgical treatment and to the solution of the many metallurgical problems in order to effect a greater commercinl saving. With this plan in view, field work was begun in the latter part of May, 1917, and was continued during the summer. E. K. Soper, formerly professor of mining, University of Idaho, and now dean of the mining department of Oregon Agricultural • College, Corvallis, Oreg., visited the mining districts in central and southwestern Idaho and also some of those in the northern part of the St.ate. D. C. Livingston, professor of geology at the University of Idaho, Moscow, Idaho, also visited some of the mining districts in central Idaho during the summer; in addition, much valuable information he had gathered on former trips to many other districts is included in this report. Credit is also due Mr. Livingston for the maps covering the State, as well as the bibliography nt the end of each chapter. Thomas Varley, superintendent of the Seattle mining experiment station of the Bureau of Mines, spent a short time in the field, principally in the mining districts in central and . northern Idaho, and made a brief visit to the southwestern districts with Mr Soper. The field work of Mr. C. A. Wright, metallurgical engineer of the Bureau of Mines, in direct charge of the cooperative work, was chiefly in the Coeur d'Alene region. Mr. Wright visited nearly all of the mining districts in the region and devoted most of his time to studying the milling methods. The results of the investigation are set 1iorth in this bulletin. The bulletin aims to give the l9Calities of the various mining districts, and the nature of the present operations and those that have been carried on in the past. The geology is discussed only in a general way, the descriptions being intended more especially to bring out the types of ore deposits and the character of the ores, a knowledge of which is essential in determining the proper treatment of the ores. The writers do not wish to imply that all districts mentioned in this bulletin were visited during the summer of 1917, for a great deal of the material has been gathered from other reports, especially from publications of the United States Geological Survey. However, it is hoped that this report will be of help to those who are interested in mining in the State of Idaho. The plan is to continue the field work and subsequently publish the results of the investigations in much more detail, with greater emphasis given the metallurgical treatment of the ores and the problems involved.

Jan 1, 1919

By Dodd SF

Valuation of mining companies and their underlying assets prepared by brokers' analysts are, by necessity, approximations. The reliability of the valuations is entirely proportional to the quality of available data, the reliability of forecasts and the nature of underlying commodity price assumptions. The latter is perhaps the greatest single cause of gross variations in company and asset earnings estimates and- valuations. Assumptions are often necessary regarding commodity price achievement based on commodity hedge positions. Public disclosure from listed companies provides a sound base from which to project earnings, cashflows and balance sheets. The uncommon disclosure of projected production and cost schedules often reduces the reliability of future estimates. The application of reserve and resource estimates is contentious with practitioners applying differing weightings to importance of resources in estimating mine lives (and therefore cashflow streams). Valuation methods applied in equity markets usually focus on relative value and the identification of pricing anomalies. The commonest ""rules of thumb"" applied in the valuation of mining companies (and therefore their underlying assets) is with the use of year specific price/earnings (P/E) and price/cashflow (P/CF) ratios, with low multiples suggesting undervalued assets, high multiples overvalued situations (but these rules can often be clouded by market expectations of underlying commodity price movements). Another simply applied valuation tool is to examine the examine the value placed on reserves and resources by the market. Inexpensive gold in the ground (expressed as $ of market capitalisation per ounce of reserves or resources) might indicate a buying opportunity, but the market does discount the value of gold in the ground prior to mine development and where development risk is perceived.

Jan 1, 1994

By Shawn Collins

BACKGROUND The history of the Pine Point Mine is a rich one. This property once boasted one of the largest and most profitable lead-zinc mines in Canada's long and storied mining history. The Pine Point mine used open pit technology to extract the ore, but they faced several challenges. In addition to logistics problems with haul distances and metal prices, the mine faced the challenge of a large in flow of water from the Great Slave Lake. Eventually, the Pine Point Mine was closed leaving behind a large deposit of lead-zinc ore. Following the closing of the Pint Point Mine, Tamerlane Ventures Inc. acquired this property which includes approximately 70 million tonnes of lead-zinc reserves. The initial phase of this project will concentrate on the R-190 deposit as a test site to prove their new approach for extracting the ore. The R-190 reserve is believed to have approximately 1,014,000 million tonnes of high grade ore varying from 5% to 52% combined lead-zinc. Once the pilot project proves the approach is valid, the process will be repeated in approximately 33 other ore bodies on the property. This paper is written to discuss the design process to determine the most effective means of placing production and service equipment in the same shaft. Currently the design work and the mining scheme is complete, but lead-zinc pricing has prevented Tamerlane Ventures Inc. from moving forward with the project.

By M. Hepokoski, M. Klein

"Mine refuge shelters are designed to protect mine workers from hazardous environmental conditions after a mine disaster, but high temperature and humidity levels inside these shelters may pose a significant safety risk. Due to the safety risks associated with human testing, detailed thermal models of shelters and human occupants have been developed using TAITherm simulation software. These models are used to predict the temperature and humidity within the shelter resulting from metabolic heating, evaporation due to sweat and respiration, moisture and heat from the shelter’s carbon dioxide scrubbing system, and heat transfer within the shelter. A detailed human thermoregulation model simulates the sensible and latent heat generated by the shelter occupants, and predicts the occupant’s body core temperature and moisture lost due to sweating and respiration. This information is used to assess the safety of the shelter. This paper presents the technical details of the human thermal model, validation comparing the human model to human subject test data, and results of a mine shelter analysis. IntroductionPortable mine refuge chambers are used in U.S. coal mines to provide protection to mine workers from hazardous conditions following a traumatic event. Although these shelters are designed to supply clean air and sustenance for up to 96 hours, prolonged exposure to the mine shelter environment itself can pose a substantial risk to human safety. Heat generated by the shelter occupants combined with heat from the carbon dioxide (CO2) scrubbing system can raise the shelter interior temperatures and relative humidity to dangerous levels that can lead to heat stress in humans. Unfortunately, the thermal burden associated with mine shelter exposure is not well characterized due to potential hazards associated with underground human subject testing. In order to assess the thermal burden on people within a mine shelter environment, a detailed thermal model was created to accurately predict the temperatures and humidity levels within the shelter, and the impact of these environmental conditions on human occupants. The model consists of a mobile inflatable tent-type mine shelter with 23 humans, and includes the surrounding mine environment. The thermal simulations were performed using a validated commercial heat transfer prediction computer software. Additionally, a module of the software provided the capability to simultaneously model the thermophysiology of 23 unique humans contained within the mine shelter. The human thermal models accounted for the thermal interaction with the environment and provided a core temperature response prediction that can be used to evaluate survivability in heat stress situations (U.S. Army, 2003). The models can also be used to determine maximum occupancy in order to maintain safe temperature and humidity levels inside the shelter in specific mine environments, to optimize shelter size for maximum heat dissipation, or to simulate active cooling systems."

Jan 5, 2017

By Dave Bulled

"This paper describes the design of an SABC grinding circuit using CEET technology applied to grindability data produced from testing 100 samples and distributed across the blocks of a mine plan using a geostatistical approach. The data distribution required the identification of the location of the sample points and a geological plan of the 130 million ton Ruby Creek orebody together with a mine plan of about 11000 blocks to be mined during the proposed 18 year life of the mine. The mill design was then made with consideration for the estimated hardness of each block in terms of both SAG and Ball milling with allowance for annual periods when the ore is harder to grind. Operating specifications were selected to achieve an optimum of capital and operating costs through use of the CEET program. The geostatistics assigned the statistical error that arises from having a limited amount of sample testing data to the hardness estimate of each block of ore in the mine plan. The final design could then include a quantification of risk and determination of safety factors based on the accuracy of block hardness estimates and CEET model fitting.INTRODUCTIONThe traditional approach to plant design involves the extensive testing of a single large composite sample or a small number of composite samples that are reputed to represent the ore body. It is accepted that the tests used can accurately measure in the laboratory the grindability of the sample by a process representing that to be used in the plant. The size of equipment required to achieve a specified throughput and product size is then calculated from one of a variety of models that have been developed by metallurgists over years of trial and error. Since these tests and models are tried and tested, they are accepted as reasonably precise; however during the operation of the resulting plant the design is sometimes found to be inadequate. It is then suspected that the flaw in the design process lies in the samples not being sufficiently representative of the ore body, since using only a single or small number of composite samples does not recognize the variability of the hardness of the ore, nor does it allow for the lack of precision in the hardness value used in the design.This paper outlines a design procedure suited to an orebody that is described by a geostatistical analysis of a reasonably large number of small samples of drill core. The analysis required the identification of the location of the sample points and a geological plan of the orebody, together with a mine plan of the blocks to be mined during the proposed life of the mine. The mill design was then made using the estimated hardness of each individual block with an allowance for annual fluctuations in the grindability of the ore. The geostatistical analysis assigned a statistical error to the hardness estimates of blocks and of each production year such that the final design included risk estimates and safety factors based on the possible errors that arise from having a limited amount of sample data (Kosick et al. 2002)."

Jan 1, 2007

By H. J. Lechtenberg

Preliminary results are given of solvent stimulation of two wells producing viscous oil (14°-17° API) from the Tar zone in the Wilmington field, California. The solvent (coker oil, an intermediate refinery product) was injected into the formation, and after a soak period, the well was returned to production. Data are given on crude oil properties, solvent properties, determination of volume of solvent in the produced oil, rate of oil production before and after stimulation, volume of additional oil produced, and volume of solvent recovered. Although further study and improvement of the method arcs needed, cyclic solvent stimulation appears to be an unqualified success in one well and a moderate success in the other.

Jan 1, 1972

By R. E. Wilmot

This paper is based on the experiences, over many years, of numerous authors in the South African mining industry and of the hot dip galvanizing process and its application as a corrosion protection system. The paper sets out the extensive development, financial resources and stringent operating requirements of the South African mining industry. After many years of research and operational experiences, hot dip galvanizing and, when necessary, duplex systems, have been found to meet the demanding requirements of this particular industry. The paper sets out the requirements from the standpoint of corrosion criteria and is followed with a case where the corrosion protection properties of hot dip galvanizing are demonstrated. This case history traces the early investigation of the expected corrosive conditions in a new mining operation and concludes with two follow-up visits to the mine in order to examine actual performance of the corrosion protection system after ten years in service.

Jan 1, 2007

Amid some of the worst economic conditions that the mining industry has been faced with in more than a decade, the mood among the large crowd at the 114th Annual Northwest Mining Association?s annual meeting was surprisingly upbeat. More than 2,200 attendees showed up at John Asuaga?s Golden Nugget Casino in Reno, NV for the conference held Dec. 1-5. And more than 200 companies exhibited in 240 spaces, including SME and the Minerals Information Institute. The number of attendees and exhibitors were the most for the conference in more than 10 years. The conference was held in Reno/Sparks for just the second time in its illustrious history but began under the cloud of global financial turmoil. Prior to, and during the conference, the industry news headlines were grim, to say the least. An alarming number of mine plans and expansions had been put on hold; hundreds of miners across the United States had been or were in the process of being laid off; commodity prices were falling and some of the biggest mergers in the industry fell through while miners around the world put the brakes on to take a wait-and-see approach. It was a painful time for many, but the downsizing actions taken by many mining companies was exactly what needed to happen, according to Industry Outlook Luncheon featured speaker Frederick Sturm. He is the executive vice president and chief investment strategist and member of Mackenzie?s Investment team. He has earned a reputation as one of Canada?s leading investors in natural-based companies and he also manages the Ivy Global Natural Resource Fund in the United States Sturm said that the mining industry has fallen hard and that he expects it to bounce back quickly, before falling hard again. In these tough times, he said, the companies that have pulled back on production early are doing the right thing in the long run.

Jan 1, 2009

A diverse selection of rockbolt designs and resin anchors are available for use in underground mines. Research in recent years at the UNSW Mining Research Centre led to the construction of a rockbolt pull-testing facility. This facility has subsequently been upgraded, commissioned and initial test work has been completed to verify the pull-test process. A test program has been completed with the objective to understand the load transfer mechanism and improve the general performance of rockbolts. This paper describes the results of this research. Une sélection diverse de dessins du rockbolt et ancres de la résine est disponible pour usage dans les mines de métro. Faites des recherches ces dernières années à l'UNSW que le Centre de la Recherche Minier a mené à la construction d'une facilité de l'essai de la traction du rockbolt. Cette facilité a été améliorée par la suite, le travail de l'épreuve en commission et initial a été complété pour vérifier le processus de la traction-épreuve. Un programme de l'épreuve a été complété avec l'objectif comprendre le mécanisme du transfert de la charge et améliorer la performance générale de rockbolts. Ce papier décrit les résultats de cette recherche. Eine verschiedenartige Auswahl an rockbolt-Designs und Harzankern ist dafür verfügbar, benutzen Sie in unterirdischen Bergwerken. Forschung in letzten Jahren beim UNSW-Bergbau Forschung Zentrum führte Ruckerprobung-Einrichtung zur Konstruktion eines rockbolt. Diese Einrichtung ist anschließend befördert worden, ist beauftragt worden und wird abgezeichnet, prüfen Sie, die Arbeit ist vervollständigt worden, um den Ruckprüfung-Prozeß zu verifizieren. Ein Prüfungsprogramm ist mit dem Objektiv vervollständigt worden, den Lastübertragungsmechanismus zu verstehen und die allgemeine Aufführung von rockbolts zu verbessern. Dieses Papier beschreibt die Ergebnisse dieser Forschung.

Jan 1, 2003