Search Documents

By P. Venter, N. Naude

"Coal mining is a thriving industry and 53% of the coal mined in South Africa is used for electricity generation. Mechanization has made coal mining more efficient, but fines generation has subsequently increased. Up to 6% of the run of mine material can report to the -200 µm fraction. Common problems associated with fines handling include dust formation, storage problems, and high moisture levels. A method to turn this material into a saleable product instead of stockpiling it can add value to a company.Briquetting is a pressure agglomeration method where loose material is compacted into a dense mass (FEECO International, 2014). The briquettes must be able to withstand rigorous handling and transport operations without disintegrating. This study aims to investigate the optimum binder and moisture conditions required to produce a mechanically strong briquette using two different binders - a PVA powder (binder A) and a starch powder (binder B).It was found that for binder A the optimum moisture level was 12% to 14%. At this moisture level the greatest compression strength gains were observed, and low amounts of fines produced in impact and abrasion tests. The minimum amount of binder added while still obtaining a strong briquette was 0.5% binder A. For binder B the optimum moisture level was also 12% and the minimum amount of Binder B to be added was found to be 1%. Briquettes that were dried outside reached their peak strength after about four days, whereas the briquettes that dried inside took about 20 days to reach their strength plateau. Hardly any degradation took place on the surface of the binder A film after exposure of 300 hours of artificial weathering. Thermogravimetric analysis confirmed that neither binder A nor binder B will add to the ash content of the coal fines, as both binders totally decompose above 530°C.Binder B yielded stronger briquettes after 15 days and also generated less fines. It is therefore superior to binder A and would be recommended for further use.Paper written on final year project work carried out in partial fulfilment of B.Eng degree in Coal Beneficiation"

Jan 1, 2015

Queensland?s underground coal industry, as a whole, has arguably the best gas monitoring systems in the world. Each mine utilizes real time, tube bundle and onsite ultra fast gas chromatograph systems. Queensland?s mining legislation has specific requirements for mine gas monitoring but there is no requirement for all three techniques. Industry has however identified the need for all three and adopted this as a standard, resulting in over sixty thousand gas results collected each day. Automated monitoring systems are programmed to alarm for gas concentrations, gas ratios and explosibility. These alarms are then used to initiate predetermined actions to take control of the situation and prevent the compromise of safety to workers and the loss of resources. Dedicated software packages have been developed to assist in the interpretation of the large volume of results generated. The real time systems are used for real time warning, essential for incidents such as belt fires. Tube bundle systems suit long term trending used for identification of the onset of spontaneous combustion or for the determination of explosibility during the routine sealing of worked areas. Gas chromatograph analysis is used to provide a complete analysis and provides results for hydrogen and ethylene, key gases used in the assessment of spontaneous combustion. It is also crucial during significant spontaneous combustion events and coal fires to use gas chromatography to determine the explosibility status of the underground atmosphere otherwise the severity of the situation is likely to be under estimated. This paper outlines the need for all three techniques for assessing the underground status and outlines advantages and disadvantages of each.

Jan 1, 2009

By M Cooper

Since its enactment in 1991, the Resource Management Act (RMA) has generated both praise and criticism. The major criticism is in relation to the costs the Act poses to industry and the time it takes to work through the process. In response to such criticisms the Minister for the Environment has initiated a review of the implementation of the RMA. The Minister's proposals for reform have not yet been released and the discussion that follows is based upon the report by the Minister's Review Group which was released in September.

Jan 1, 1998

By Robert Martin, Brian W. Stump, David P. Anderson, W Scott Philips

Since 1994, various mines in the US have cooperated with research scientists at the Los Alamos and Lawrence Livermore National Laboratories to address issues related to verification of the Comprehensive Test Ban Treaty (CTBT). The .CTBT requires that no country may conduct any nuclear explosion in the future. While the CTBT is a significant step toward reducing the global nuclear danger, verifying compliance with the treaty requires that the monitoring system be able to detect, locate and identify much larger numbers of smaller amplitude seismic events than had been required previously. Large mining blasts conducted world-wide will be of sufficient amplitude to trigger the monitoring system at the lower threshold. It is therefore imperative that research into the range various blasting practices employed, the relationship of yield to seismic magnitude, and identification of anomalous blasting results be performed. This paper will describe a suite of experiments funded by the Department of Energy and conducted by the Los Alamos and Lawrence Livermore National Laboratories in cooperation with the US mining industry. Observations of cast blasting, underground long wall generated coal bumps, stoping, and explosively induced collapse of room and pillar panels will be presented. Results of these dual use experiments which are of interest to the mining community will be discussed. These include 1) variation of amplitude of seismic energy at various azimuths from cast blasts, 2) identification of the extent of back failure following explosive removal of pillars, and 3) the use of single fired shots for calibration of the monitoring system. The wealth of information and discovery described in this paper is a direct result of mutual cooperation between the US Government and the US Mining Industry.

Jan 1, 1997

By H. J. Uananisa, M. J. Papo, C. W. Siyasiya, W. E. Stumpf

"SynopsisThe need to reduce weight while maintaining good mechanical properties in materials used in the automotive industry has over the years seen an increased exploitation of various steels to meet this new demand. In line with this development, the ferritic stainless steel family has seen a wide application in this industry, with the AISI 436 type increasingly being used for automotive trims and mufflers for exhaust systems, as well as a significant part of this steel’s application being for the manufacture of wheel nuts and wheel nut caps in trucks, mainly through the deep drawing process. However, there have been reports of some poor surface roughening of this material during deep drawing, with tearing and/or cracking also reported in some instances. This has been suspected to possibly be associated with some local differences in localized mechanical properties between grains and grain clusters of the rolled and annealed material.In order to investigate the poor surface roughness exhibited by AISI 436 ferritic stainless steel (FSS) during deep-drawing, Lankford values (R-mean and ?r), grain size, and microtextures of various sheet samples from this steel were studied. The chemical composition range for the samples was 0.013–0.017% C, 17–17.4% Cr, 0.9–1% Mo, and 0.4–0.5% Nb. The steels were subjected to various hot and cold rolling processing routes i.e. involving industrial direct rolling (DR) or intermediate annealing rolling (IR), and the drawability and final surface qualities of the steels were compared. It was found that the DR route gave an average R-mean and ?r value of 1.9 and -1.4 respectively, while the IR route yielded an average Rmean and ?r value of 1.6 and 0.52 respectively. The high ?r value for the DR processing route had a substantial adverse effect on the drawability. IR samples exhibited a smoother surface finish on visual inspection, while clear flow lines were visible on the DR samples, despite the fact that DR is the preferred industrial processing route due to the reduced production costs it offers. This observation was also confirmed through SEM examinations. The difference in the surface quality was attributed to microtexture. However, the mechanism responsible for this difference still needs to be identified."

Jan 1, 2015

When the HSE Act was introduced in New Zealand in April 1993, one of the prime aims of the Government was to signal to the industry. The Government's recognition of the employer as the key person responsible for safety and health in the workplace and to actively encourage employers to self manage the health and safety function. Because of the significant change in the philosophy behind the new legislation, and because of the inherently conservative nature of the mining industry, it has taken some years for both the industry and the regulators to reach the stage of considering the framework in which a controlled degree of self management can proceed.   In this paper, some of the issues relating to the legitimacy of the process are considered, some of the questions raised in the minds of those charged with implementing the legislation are discussed, and the views of some eminent authors are examined.   The latter part of the paper focuses on a programme called the Reduced Site Surveillance Programme, which grew out of Goal 2 of the New Zealand Mining Inspection Group's 5-Year Strategic Plan. The programme is described in some detail, and the criteria applied at each stage of the programme is discussed. The paper concludes with the author's expectations of the longer term outcomes of the programme.

Jan 1, 1997

By J. Perlacia

"As the bulk handling sector continues its transformation to Industry 4.0, the mining industry, and its harsh working and environmental conditions, provides a perfect spot to study the feasibility of remote analysis and maintenance of the components used for bulk handling. The most important and expensive tools have been adapted to the digital era in recent years, from remotely controlled haul trucks to monitored conveyor belts.However, the big items of the installations rely on smaller parts that have been leftaside, mainly due to the difficultyof adapting them to the Internet ofThings (IoT).The paradigmatic example is the lack of monitored rollers, while all the other components of the conveyorbelt installations (the belt itself, motors, drums, etc.) were monitored some time ago. The main problem is that a failure of a single roller can cause the stoppage of the entire conveyor, due to possible damage to the belt. Thus, the implementation of an integral monitoring system of all the components of the conveyor is a must.The research and development department of ULMA Conveyor Components has been working since early 2012 on the development of monitored rollers, testing all the problems until their final installation in different demanding conditions, from the extreme heat in Australia to the freezing cold of Norway. All the tests have been done under actual working conditions, in real installations and have provided valuable knowledge in the identification of problems, their solutions and the final advantages of a roller monitoring system.Background and current stateThe malfunction of a single roller in certain conveyor belts can force the standstill of the entire installation until its replacement, due to the risk of greater and more expensive failures, such as a rip in the belt. In the case of a bulk handling installation, where a continuous supply of material is necessary, an unexpected stop of one hour could result in huge economic losses."

Nov 1, 2019

By Natasha A. Essar

Nevsun Resources Ltd. Bisha Mine Project is a gold and base metal development project in the Gash Barka region of west-central Eritrea. The project has the potential to be one of the largest industrial developments in the country, and Eritreans have no experience in modern mining. Nevsun recognized early that the success of the Bisha Project would require meaningful consultation and engagement with all levels of Eritrean society. Meaningful engagement required not only full disclosure, but also capacity building from government officials at all levels to other stakeholders who live in the nearby communities. This paper describes the approach used to develop capacity and to help introduce a modern mining culture in a country without previous experience in mining.

May 1, 2007

This Bureau of Hines report on underground mine communications addresses methods and equipment to meet the communication requirements of working sections and places of coal and metal-nonmetal mines. A review of the status of trapped miner detection is also presented.

Jan 1, 1977

By James Westfield

This publication covers the work of the Division of Coal Mine Inspection, Bureau of Mines, as performed under provisions of the Federal Coal Mine Safety Act. It presents background information and data since 1952 when the Act became effective and includes up-to-date statistics for the calendar year 1962. During that year, approximately 9,704 coal mines were active in the United States, and the Bureau made 12,810 regular inspections. BACKGROUND The Federal coal-mine inspection program was established to carry out the provisions in Public Law 49, 77th Congress, (H. R. 2082) approved May 7, 1941. This act has since been amended as Title I, Advisory Powers Relating to Health and Safety Conditions in Mines, under Public Law 552, 82d Congress, approved July 16, 1952, which also included Title II, Prevention of Major Disasters in Mines. Public Law 552 is known as the Federal Coal Mine Safety Act.

Jan 1, 1963

By B Poborowski, A Chen

"For some time, the Australian and Chinese underground coal mining industries have evolvedindependently with minimal infl uence on each other. Despite the fact that in recent years severaltechnologies and solutions have become common to both industries, this trend has seeminglycontinued to the point that there are still many important diff erences in legislation and hazardmanagement systems in both countries. Austar Coal Mine as an Australian based and Chineseowned enterprise has a unique opportunity to benefi t from the technology and knowledge ofboth nations. This paper compares the Australian and Chinese approach towards spontaneouscombustion hazard management in order to exchange experience, identify possible improvements and learn from each other."

Jun 1, 2012

By J Harris, J Li, M Shi, P A. Kirsch, D Sprott

Australia has an enviable global reputation as a leader in health and safety outcomes in the hazardous industry of mining, in part due to an increased application of risk management regarding operational planning and mining practice. In 2010, the Australian Coal Association Research Program (ACARP) initiated a major project, RISKGATE, to build, capture and deliver a national body of knowledge to assist companies with the management of risk in coal mining. The online system contains information for tyres, collisions, fires, isolation, strata underground, ground control open cut, explosions, explosives underground, explosives open cut, manual tasks, slips/trips/falls, outbursts, coal bumps and bursts, human–machine interface, tailings dams, occupational hygiene and inrush. In 2014, RISKGATE is developing content for fitness for work (fatigue, drugs, alcohol, physical well-being, psychosocial well-being).This paper analyses underground mining fatalities in Australia and the United States since 2002 and introduces RISKGATE with a focus on the knowledge base for management of hazards in underground operations. Through capturing coal industry expert operational knowledge, RISKGATE provides a cumulative corporate memory at a time of high personnel turnover within the mining industry. This coal-based body of knowledge is a platform that can be evaluated and implemented for other mining domains and high-risk industries within the energy supply chain.CITATION:Kirsch, P A, Shi, M, Harris, J, Li, J and Sprott, D, 2014. RISKGATE and underground operations, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 11–18 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By Francis Church Lincoln

"INTRODUCTION During the period from September 18 to November 27, 1944, the Bureau of Mines conducted an investigation and exploratory churn-drilling program in an area immediately north of the Crow Branch Diggings, a district lying approximately 2 1/2 miles southwest of the town of Livingston in Grant County, Wisconsin.The work was undertaken as part of a general Bureau of Mines investigation of the zinc-producing area of southwestern Wisconsin at a time when all effort was being made to increase the production of metals important to the Nation's war prrgram.Although no mining has been done in the district in recent years the Crow Branch Diggings were an important source of galena and may be found today in the dumps remaining from old surface-mining operations.The Bureau of Mines undertook an exploratory churn-drilling program on the northwestern projection of the general strike of the digging in a zone where subsurface,lead and zinc mineralization had been reported from drilling done in the early 1900's."

Feb 1, 1947

By Lana Alagha, Fardis Nakhaei, Jose L. Corchado-Albelo, Noelia Munoz-Garcia, Michèle Heitz

Sulfide tailings from past and present mining activities are important hosts of critical elements and precious metals. This review paper presented a literature survey on the recovery practices of some critical minerals containing Te from sulfide tailings with a special focus on the physical beneficiation and hydrometallurgical separation methods. Finally, a conceptual framework and possible processing flowsheets were proposed. The findings of this review will be useful for the researchers in the field of geochemistry, mineral processing, and metallurgy to evaluate the separation processes for reprocessing of mine tailings for the recovery of critical minerals.

Feb 1, 2024

Gold mines produce unique water treatment requirements. This paper focuses on case studies of innovative processes used for treatment of water resulting from gold mining and processing. The case studies include treatment of mine dewatering water for beneficial application from an Australian gold mine, Bendigo Mining, as well as treatment for arsenic removal of tailings water from mining and processing at Goldcorp mines in Canada. Gold mining can often require dewatering to prevent groundwater seeping into and flooding the mine workings. Gold mining and processing often accumulate wastewaters in a tailings dam. The mine water can contain contaminants such as dissolved salts, iron, arsenic, manganese, heavy metals and odorous sulfates. Environmental discharge requirements as well as community needs for water drive mine operators to consider the most appropriate water treatment process. Treatment of gold mine water can require processes including oxidation, pH adjustment, coagulation, flocculation, clarification, further oxidation/adsorption of specific metals such as manganese, filtration, salt reduction utilising reverse osmosis, brine minimisation and other innovative technologies. These processes are discussed through the case studies with examination of the specific treatment process that is required. This paper uses real case studies of gold water treatment processes to explain and examine the technology and the reasons for designing specific processes. The focus is toward explaining innovative processes where the water is used for sustainable environmental discharge or treatment to a quality that can be beneficially used by the local community.

Jan 1, 2007

By Leigh J. Wardle

This paper describes a numerical method for calculating the three¬-dimensional stresses and displacements induced by tabular excavations in a rock mass consisting of parallel layers of distinct material properties. The method is based on the superposition of numerical solutions for elementary displacement discontinuities in a parallel layered rock mass. The method can be used to analyse complicated excavation layouts such as those encountered in room-and-pillar or longwall mining. The method can automatically take into account the effect of the earth's surface. The method offers an economic and efficient solution to stress analysis problems which cannot be adequately modelled using two¬-dimensional methods and for which the expense of three-dimensional finite element or general boundary element analysis cannot be justified.

Jan 1, 1984

By J. Engels

CODELCO is considering the implementation of high-density tailings management at the Chuquicamata mine in northern Chile for its long term disposal plan. To achieve this, CODELCO commissioned the design, construction, and operation of a 70 t/d pilot plant, fed by existing tailings. The testing programme was completed in May 2011, and consisted of laboratory rheological and characterization assessments, pipe loop testing, beaching trials, and analyses of deposition behaviour for solid contents ranging from 57?68% (w/w). This paper describes the characteristics of the pilot plant, the testing programme, the beach trial analyses, and the resulting beach profile predictions based on the stream power theory. CODELCO also used other predictive beach slope methods, such as the equilibrium slope concept, which are not discussed in this paper. The final beach profile for design will be selected after an expert analysis of all methods has been completed.

Jan 1, 2012

By J. Galloway, P. K. Hofmeyr

Obviously all mining operations require much analytical work to be carried out. This starts with exploration, becomes more stringent with the evaluation of a mineralised area and finally becomes on-going when mining operations are under way. All these phases are carried out by geologists, metallurgists and mining engineers. They require analyses to carry out their functions but usually have no involvement in the analyses themselves. Analyses are carried out at commercial laboratories or in-house analytical laboratories. In the past in South Africa the tendency was for the larger mining houses to have their own centralised laboratories for exploration samples with each mine having it?s own laboratory to meet only that mine?s requirements. The centralised laboratory maintains QC functions at the subsidiary laboratories. In other mining areas of the world there has been a strong tendency for all geological analytical requirements, especially for exploration and mining, to be carried out at commercial analytical laboratories. In recent years there has been a tendency for mines in South Africa to move in the same direction. This paper discusses the factors that need to be taken into consideration when a new laboratory is being planned and automation is an option. The planning of the laboratory at the new Langer Heinrich Uranium mine in Namibia is discussed considering these factors. 2.0 REQUIREMENTS OF A MINING ANALYTICAL LABORATORY The purpose and requirements of a mining analytical laboratory are fairly obvious and can be summarised as follows :- 1. All mining operations must have access to analytical facilities, either in-house or commercial 2. The laboratory must be able to handle all the sample types submitted by the mining operation These can be mining, exploration and/or plant samples. They can comprise solids (rocks, bore-cores), slurries and/or liquids.

Jan 1, 2007

By W. F. Van Impe

The design of piles and of pile groups has remarkably progressed over the past two decades. The in­creasing complexity of the building concept implements a more rational approach of the deep foundation capacity and its interaction with the structure. Moreover, the understanding of the soil characteristics relevant to deep foundation behaviour, is continuously in progress because soil parameters are always more accurately determined; which also contributed a lot to the recent developments in pile capacity design. At last, due to the increasing sensitivity of buildings to deformations, continuous attention must be also paid to pile group settlements. The aim of this report is to discuss some of the mentioned more important pile design developments.

Jan 1, 1994

By P. Rosario

The application of high pressure grinding rolls (HPGR) has been growing in the mining industry for the last 10 to 15 years. The major benefits supporting this trend are better energy efficiency, improved grinding capacity, and higher metal recovery in downstream processes such as heap leaching and flotation. In general there is limited quantitative knowledge on the true benefits of HPGRs relative to SAG mills in comminution, and about which situations one deals with better than the other. This paper will present a structure for comparison of the energy requirements for HPGR versus SAG mill considering complete circuits for comminution of precious and base metals hard ores. The work presented is from the design of four complete circuits based on ore data from two sites.

Jan 1, 2010