Search Documents

By Zhucheng Huang, Yuanbo Zhang, Kecheng Zhang, Guanghui Li, Tao Jiang

"With rapid development of Iron and Steel industry, plenty of metallurgical dusts and sludges are generated, which have not been effectively utilized because of their poor hydrophilicity and bad ballability. Agglomeration and roasting of metallurgical dusts & sludges with a new-type composite binder are studied in this paper. The results indicate that the dosage of the new binders can be decreased to 2.5 wt% from 3.5 wt% when using the wet-grinding process. Under the optimal conditions of briquetting pressure 2070 N/cm2, briquetting moisture content 13 wt%, roasting temperature 1000 °C and roasting time 40 min, the qualities of the green, dry and roasted briquettes meet the requirements of the industry production. The finished products have the compression strength of more than 2000 N/cm2, which can be used as high-quality burdens for blast furnaces.IntroductionWith rapid development of Chinese Iron & Steel industry, there are more and more serious resource shortage and environmental pollution existing. Converter sludges, containing 30% ~ 40 wt% moistures, are typically difficult for recycling [1]. Foreign processing technologies for sludges treatment are relatively advanced including cold-bonded agglomerates for blast furnace, RHF reduction for the dusts and sludges with high content of Zn and Pb, smelting and reduction. Domestic iron and steel companies use a small amount of sludges in sintering. However, the sludges have the characteristics of high moisture and containing harmful impurities, which directly affect the sintering mixture permeability and product quality [2-5]. There are also other technologies such as production of metallized pellets, cooling agents for steelmaking, etc [6]. All of these deficiencies and applied are not in large-scale."

Jan 1, 2011

By Guohua Bai, Mingjun Rao, Jianchen Lim, Guanghui Li, Tao Jiang

"By using thermogravimetry, optical microscope and chemical phase analysis, the solid-state reduction of carbon-burdened chromite pellets in the absence and presence of additives were investigated. The effects of reduction temperature, reduction time and additives on the metallization of chromite pellet were studied. The results indicate that the pre-reduction ratio of carbon-burdened chromite pellets is improved with the increase of reduction temperature and the addition of additives. The metallization of chromium is increased from 63.9% to 92.8% at 1300 °C for 4h with the addition of 2 wt.% of sodium borate. Investigation suggests that the reduction of carbon-burdened chromite pellets is diffusion controlled. The apparent activation energy without additive is 192.1 kJ/mol, while it decreases to 170.4 kJ/mol in the present sodium borate.IntroductionFerrochrome is used to produce high strength, corrosion resistant, wear-resisting, high temperature resistant and oxidation resistant special steels, and it is becoming one of the most important alloy materials for the production of stainless and high alloying ferritic steels [1-5]. Demand for ferrochrome is steadily on the rise due to the growth of stainless steel industry. Nowadays, more than 80% of the world's ferrochrome is utilized in the production of stainless steel [6-7].Ferrochrome is mainly produced in submerged-arc furnaces (SAF) with chromite lump ore. However, lump ore merely accounts for 20% of the chromite ore output, while fine ore (< 8 mm) accounts for about 80% [8]. Therefore, agglomeration of chromite fine ore is necessary before charging into SAF."

Jan 1, 2011

By L. Y. Zhang

The current status of metal hydride alloys for NiMH batteries was systematically reviewed. Extensive application-oriented research and development has successfully made the NiMH battery an important part, with growing potential, among rechargeable batteries. The rare earth based metal hydrides (AB5) have been considered the best alloy material for use in the negative electrode in NiMH batteries. However, being in demand for high performance electronic markets, the still young NiMH industry is facing serious technical challenges in developing better products. Among all the efforts to respond to the challenges, advanced AF3, alloys are in great demand: the capacity enhancement race requires new or improved alloys possessing higher volumetric capacity; price competition mandates MH materials with low cost; high performance under severe service environments calls for alloys with high corrosion resistance when subjected to electrochemical cycling; and finally, high power service requires the negative electrode to deliver current at high rates.

Jan 1, 1997

By G. A. Eltringham, A. F. Sarofim, A. A. Shook, M. P. Heap, B. R. Adams, K. A. Davis

This paper discusses the use of a reacting CFD model to determine chalcopyrite kinetics in a drop tube furnace and to predict the reaction of a chalcopyrite concentrate in the reaction shaft of an industrial smelter. Reacting CFD codes can be applied to determine the consequences of the interaction of gas with particles and therefore improve the ability to derive kinetic parameters that take into account the different temperature and oxidation histories that different particles will see. This paper describes the application of such a model to derive improved kinetic parameters for the pyrolysis and oxidation of chalcopyrite. The improved kinetic parameters derived from the drop tube studies are used to simulate chalcopyrite concentrate reactions in the reaction shaft of an industrial smelter. The reaction shaft model includes the effects of turbulent fluid mechanics, entrained flow mixing, turbulent particle dispersion, heterogeneous particle reactions, radiative and convective heat transfer, and surface and bath deposition rates. Particle reaction and composition characteristics are predicted as a function of particle trajectory and deposition and are used to aid in evaluating shaft performance.

Jan 1, 1999

By Muammer Kaya, Sait Kursunoglu

"The aim of this study was to investigate the effectiveness of ascorbic (C6H8O6) / oxalic (C2H2O4) acid as a reductant for the simultaneous recovery of zinc and manganese from a spent and mixed zinc-carbon and alkaline battery powder in sulphuric acid leaching. The effects of sulfuric acid concentration, ascorbic/oxalic acid dosages, reaction temperature and leaching time on the zinc and manganese dissolutions were investigated according to 2k full factorial experimental design; then, a simple optimization study was carried out for the best reductant. The optimum reductive acid leaching conditions were determined at 3 hours leaching time, 70°C leaching temperature, 0.5M sulfuric acid concentration, 13 g/L ascorbic acid dosage, 1/20 g/mL solid/liquid ratio and 200 rpm stirring speed. Under these conditions, the dissolution efficiencies were 99.9% for Zn and 99.3% for Mn. When our results were compared with the previous results, our findings were better than previous studies.In addition, the manganese dissolution kinetics was undertaken, and the activation energy was found to be 7.04 kJ/mol. Selective precipitations of Zn and Mn from acid solutions were carried out using NaOH and KOH. Using 3M NaOH as precipitating agent at room temperature and at pH 8; 95.4% of Zn and at pH 10; 93.7% of Mn were precipitated from the leaching solution. Under the same conditions, using 3 M KOH at pH 8; 91.6% of Zn and at pH 10, 96.4% of Mn were precipitated. Based on the experimental results obtained, an appropriate flow sheet was proposed to recover zinc and manganese."

Jan 1, 2012

By Laurent Cohen

Since the 1970s, Solvent Extraction (SX) in hydrometallurgical processes has been a key enabling technology in the production of high-purity metals. Examples include copper, rare earth oxides, uranium, cobalt and nickel. Notwithstanding incremental improvements in extractant formulations, few breakthroughs can be recounted in this industry outside of the initial amine-, oxime- or phosphine-based reagent chemistries. However, the advent of lithium-ion batteries and their stringent requirements for critical materials (lithium, cobalt and nickel) offer new challenges and opportunities for SX. Solvay recently introduced a new extractant for lithium, CYANEX® 936, and developed unique modeling software capabilities in cobalt/nickel separation using CYANEX® 272, zinc SX using DEHPA® and rare earth separations using CYANEX® 572. This paper discusses trends in SX and provides insight on processing of critical materials essential to energy sources. It also summarizes the technical and economic benefits based on extractant selection and advances in modeling.

By Reimers. Jan H.

Practically all the world&apos;s lead is produced by sintering and blast furnace smelting, or the Imperial Smelting Process which is a variant of the blast furnace process. Increased coke and labour costs and strict lead emission limits have, however, made blast furnace smelting undesirable in most countries. A change-over to other lead smelting processes providing better working conditions and lower emissions is, therefore,. expected to occur once economic conditions improve and the necessary capital expenditures can be justified. The need for new lead smelting processes has long been evident and a number of new processes have been proposed &apos;and advanced to various stages of development. One of the new processes is already proven on commercial scale, while several others are still being tested on pilot plant scale.

Jan 1, 1983

By Victor Zavodinsky, Sergey Rogov

"Pseudo-potential fully relaxed total energy calculations are used to predict a hypothetical Si1-xCxO2 (x<0.5) compound formed from SiO2 ß -cristobalite by substitution of some SiO2 complexes by CO2 molecules. The simulation shows that the Si1-xCxO2 compound can be quasi stable if the CO2 content is less than fifty per cent. It is assumed that six-molecule Si6-nCnO12 (n=3) rings can play a role of nucleuses for formation of the Si1-xCxO2 compound from SiO2 and CO2 molecules. Thus, silicon dioxide can be considered as a possible solid store for gaseous CO2.IntroductionThe problem of increasing of CO2 in the Earth atmosphere is one of the main modern problems of mankind. One of conceivable ways to decrease the harmful value of CO2 is to convert a part of it to solid state. Iota et al. [1] reported a polymeric (quartz-like) phase of CO2 solid synthesized at high pressure (~40 GPa) and at high temperature (~1800 K). Shortly after this experimental work, Serra et al. [2] reported a total energy calculation of several possible phases of CO2 using plane wave pseudo-potential density functional theory. They concluded that there should be a transition from a molecular phase to a phase isostructural to SiO2 -quartz in the range of 35 to 60 GPa. The latest calculations by Dong et al. [3] have shown that the more favored solid CO2 phase is ß -cristobalite. Recently, Kume et al. [4] have demonstrated the polymerization of CO2 even at room temperature at high pressures up to 80 GPa. Transformations of gaseous CO2 to different solid phases were studied recently experimentally and theoretically [5-8]. The main obstacle for using synthesized CO2 solid as a solution for the CO2 problem is its pressure instability. However the SiO2 ß -cristobalite with the same structure is stable.The question is whether a silicon-oxide system in which a part of atoms of silicon is replaced by atoms of carbon will be stable? If the answer is positive, this system can be considered, in our opinion, as a possible store for CO2."

Jan 1, 2009

By Shuai Wang, Gang-hua Fu, Lu Yang, Yu-feng Guo, Tao Jiang

The fluorine-bearing iron concentrate is one of the refractory raw materials for pelletization, which is mainly used in Baotou iron and steel company with lots of problems, such as narrow roasting temperature range and low compressive strength of products. According to its specific character, the effects of roasting temperature, time on the compressive strength and microstructure of pellets were researched. The results show that low melting substances formed during the roasting was the dominant reason of those problems. High melting substances were added in the roasting to investigate their effects on the roasting properties of fluorine-bearing iron concentrate pellets. Low melting substances were reduced when chromite was added. The compressive strength of products was 3100N/P when the 2% chromite was added at the roasting temperature of 1150 ºC, which was increased 700 N/P compared with the pellets without chromite, and the roasting temperature range was expanded by 170 ºC.

Jan 1, 2016

By C. P. Broadbent

Due to growing .public awareness of environmental issues and greater sensitivity towards waste management, many countries around the world are implementing more stringent legislation governing the storage and disposal of hazardous wastes containing heavy metals such as As, Sb, Pb, Cd or Hg. These wastes can no longer be dumped without providing clear guarantees that the material concerned is environmentally safe and will not leach toxic elements to the surroundings. In the Netherlands the current dumping charge for chemical waste (i.e. worst category) is $280/t, and for industrial waste this cost reduces to $75/t. If the material can be reused there may be a small positive credit for selling it, for example discard slag as an aggregate to the construction industry. A number of (pyre)-metallurgical operations, mostly associated with the extraction of metals from sulphidic ores, produce arsenic residues in the form of As2O3 containing flue dusts and speises. If the flue dust is of high purity it can be sold, though many traditional uses are being substituted by other materials. In many cases upgrading the quality of the arsenical dusts is not possible for either technical or economic reasons. Traditional practice is to dissolve these dusts in acid prior to precipitation as ferric arsenate, which is at present classified by many countries as industrial waste and can be dumped. Recent work, however, has cast doubt on the stability of arsenates for disposal and alternative disposal routes have been investigated. Tests have shown that up to 10% (dm) As can be incorporated into "glassy" silicate slags with very low levels of arsenic leaching in the cooled product. Calcium arsenate was added to a range of synthetic and industrial slags from the system SiO2-FexOy-CaO-A12O3-AsmOn, under mildly oxidising conditions and quenched subsequently in water. It would appear that this represents an environmentally acceptable method for the disposal of many arsenical residues and there is some optimism that this method will be equally applicable to the disposal of other toxic metal residues.

Jan 1, 1994

By A. L. Paverd

The petrology of a number of pyrometasomatic mineral deposits in north Queensland, Australia, were studied to evaluate the use of mineralogy and major element chemistry in the exploration for copper, lead and zinc-bearing skarns. Results indicate a direct correlation between the character of the mineralization and the composition and nature of the host rock. The study of garnet compositions proved the most useful. Economic mineralization was limited to limestone-derived skarns containing garnet of And60-90, whereas skarns containing garnet of less than contained less than 1And55 contained less than 1% total sulfide. Skarns containing garnet of And60-8S host the best mineralization; above And8S&apos; copper, lead and zinc sulfides decrease and magnetite and pyrrhotite become the dominant ore minerals. Similar correlations were found for pyroxene, amphibole and &apos;the bulk composition of the skarns.

Jan 1, 1981

By Nagahiro Saito, Takahiro Ishizaki, Daisuke Yata, Akio Fuwa

"Ternary compound-semiconductor, CuInTe2, film was deposited cathodically under potentiostatic conditions on titanium substrate from aqueous solution containing CuCl2, InCl3, TeO and HCI in this study.The deposition parameters such as electrolytic solution composition, potential and temperature were optimized· for electrodeposition of CulnTe2. Structural characterization of the: deposited film was also carried out using XRD and SEM. Electrodeposited films Were prepared and analyzed for their chemical composition using ICP. The ICP analyses showed that the stoichiometry of the films could be controlled by (1) the deposition potential and/or by (2) the electrolytic bath composition.1. IntroductionThe ternary chalcopyrite type compound semiconductors exhibit such electrical, chemical and optical properties that make them promising for photovoltaic devices (Kazmerski and Wagner 1985)(1). Many researches have been devoted to the characterization of these materials for over one and a half decades. High efficiency solar cells based on p-CulnSe2/n-CdS have been reported (Mickelson and Chen 1983)(2).The electrodeposited fil ns of semiconductors have more advantage than other physical and chemical deposition techniques; it is relatively easy and economic technique and the semiconducting properties such as band-gap variation, concentration of dopant stoichiometric composition and so on can be controlled with some accuracy. The electrodepositions of the ternary CuInS2, CulnSe2 have been reported by many workers (Hodes and Cahen 1986, Bhattachaya 1983, Singh et al 1986, Lokhande and can be prepared as both p-type and n-type. Therefore, its potential for application in optical and photovoltaic devices is one of the great interests. Bhattacharaya and Rajeshwar (1986)(9) reported the electrodeposition of CuInTe2 from an acidic bath· on indium tin oxide (ITO) and Mo substrate. Triethanolamine (TEA) was used as a complexing agent for indium. The electrodeposited CuInTe2 films were non-stoichiometric in composition under all their experimental conditions by electron-probe micro analysis (EPMA) and Auger depth profile analysis. In this paper, we report our results on the behavior .of Cu-In-Te electrodeposition from ·acidic baths; the preparation of CulnTe2 and the effect of bath composition on electrodeposited films obtained."

Jan 1, 2000

By S-L. Jämsä-Jounela

Fault diagnosis systems have attracted growing interest in a number of engineering fields. The number of applications has increased and successful results have been widely reported. The fault diagnosis system presented in this paper is integrated, and it monitors the states of the process and performs fault detection and diagnosis on the process equipment. The monitoring of process states is carried out by means of Kohonen Self-Organising Maps that is a powerful tool in visualisation and analysis of high dimensional data in engineering applications. This paper presents the results of SOM analysis carried out on the Outokumpu flash smelting process. The subsystems analyzed in more detail are the condition of the concentrate burner, the condition of the gas line on the basis of the pressure distribution in the process and the cooling water circulation of the waste heat boiler, and the condition of the furnace and furnace equipment on the basis of the temperature distribution in the furnace and gas line. Keywords: Fault diagnosis, Process monitoring, Kohonen Self-Organising Maps, flash smelting

Jan 1, 2001

By Shenghui Guo, Jian Chen, Hongbo Zhu, Jinhui Peng, Linqing Dai, Qianxu Ye

"Response surface method (RSM) based on mono-factor experiment was applied for the process optimization of sintering of chromite fines by microwave. In RSM analysis, effects of binder addition amount, sintering temperature and holding time on the compression strength and shatter strength of the sinter were examined. Results showed that the optimal values of the above parameters were determined as follows: binder addition amount of 1.90% (in mass), sintering temperature of 1153? and holding time of 16 min. Under the optimized conditions, the compression strength was 11155.8? and shatter strength was 95.6849%. The results show that the process was optimized by response surface methodology is stable and feasible, and provide a new way for sintering of chromite fines.IntroductionChromite ore is the main feedstock for ferrochrome, and ferrochrome can be used as steelmaking additive to produce a variety of great strength, corrosion resistant and oxidation resistant special steel, which can be widely used in the aerospace, automotive, shipbuilding, military departments[1], and it has important strategic significance. At present, among the annual world's mined chromite the number of lump ore continues to diminish with its price rising sharply, while the proportion of ore fines been always increased, and the difference in prices between ore fines and lump ore is growing[2]. Despite the low price of chromite fines, and its rich in resources, it can be only used for ferrochrome smelting after agglomeration. Thus manufacturing blocks by using cheap chromite fines is an effective measure to reduce the cost of ferrochrome production and use the chromite resources[3]."

Jan 1, 2013

By I. Kim, J. C. Choi, W. D. Cho

"The effect of yttrium addition on the oxidation behavior of Fe3Al intermetallic compound was investigated in the range of temperature 800 to 1100 °C in 0.2 atm 02 in terms of oxidation rate and oxide adhesion. The oxidation rate of alloys, Fe-14.3 wt% Al and Fe-14.1 wt% Al-0.3 wt% Y, was nearly identical and the parabolic rate constant calculated as a function of temperature is Kp=5128 exp[-39506(cal/mol)/RT] mg2/cm4 hr.Rapid cooling and ultrasonic stress tests were carried out to test adhesion of scale formed on the alloys. While the oxide layer formed on the Fe-Al alloy without Y was found to be fragile and detached easily during the tests, the oxide layer formed on the Fe-Al alloy containing Y was protective, dense, and adhesive. The following two mechanisms were proposed to explain the adhesion improvement of Ah03 formed on the Fe3Al containing yttrium : (1) the addition of yttrium decrease generation of growth stress in alumina scale because the preferential diffusion of yttrium through grain boundary in alumina scale prevent internal oxidation of Al, one of main causes of growth stress, and (2) the second phase formed on the oxide scales prevents crack propagation through the scales, leading to better mechanical stability of the oxide scales.IntroductionIron aluminides have attracted the attention of many researchers as a candidate for use at high temperature because of their excellent oxidation resistance due to the formation of protective alumina scale. In order to resist aggressive environments at elevated temperatures, oxide scale formed on iron-uluminum alloy must satisfy the following three requirements : (1) thermodynamic stability (2) slow growth rate (3) adherence on substrate. According to Wallwork and Hed [l], the most suitable alloys for high temperature application are Fe, Ni, and Co alloys with the protection of Si02, Cr203, and Ah03 scales. While chromium oxide can vaporize as Cr03 above 1000 °C and silicon oxide may form low melting silicate [2,3], Alz03 has a high melting point and is the most stable among the three oxides thermodynamically [6]. In this respect, iron aluminides forming alumina seem to be most suitable for use at high temperature. However, alumina scale formed on the iron aluminum alloys tends to be easily spalled during oxidation due to the combination of growth stress and thermal stress."

Jan 1, 1998

By John R. Goode

Barrick Gold Corporation operates gold mines in the United States, Chile, &apos;Peru, Canada, and in the near future, in l1anzania. Barrick meets environmental requirements and limits the potentially adverse effect of cyanide discharge to the environment using various cyanide destruction techniques. Barrick operations use, or have used, natural degradation, ferrous sulphate, hydrogen peroxide, Caro&apos;s acid, alkaline chlorination, and the SO/Air process for cyanide destruction. This paper presents a general discussion of the options for controlling cyanide in plant effluent and provides details of Barrick&apos;s operating experience including general notes on costs.

Jan 1, 1998

By C. J. Newman

Prior to 1995, the smelting process at the Kennecott Utah Copper Corporation (KUCC) smelter consisted of Noranda reactors and Pierce-Smith converters. In the consideration of expansion opportunities, the existing process did not lend itself to a program geared towards processing the total output of KUCC mining and milling operations. During 1989 and 1990, a number of smelting options were evaluated. The final selection was the Outokumpu flash smelting process, coupled with the new Kennecott-Outokumpu flash converting technology. Facilities were designed and installed to process 1:0 million tonnes per year of copper concentrate, with the ability to expand to 1.2 million tonnes per year. Following the shutdown of the smelter facility utilizing the Noranda technology in May 1995, the flash smelting, furnace commenced operation in June with the flash converting furnace startup following a few weeks later. The smelter has achieved design production targets and environmental goals. Current operating rates are at or above design rates for concentrate and matte processing. Emissions are lower than the permit levels and equate to less than 3.5 kg of SO2 per tonne of copper. This paper outlines the design, construction, startup and the first two years of operation of the modernized KUCC smelter.

Jan 1, 1998

By Larry M. Southwick

Considerable process and equipment development and analysis were conducted during design of Freeport Sulfur&apos;s laterite nickel facilities in the late 1950&apos;s. These covered ore concentration at Moa Bay, Cuba, and concentrate refining at Port Nickel, Louisiana. Both facilities utilized acid pressure leaching and product refining steps that were similar to those later used elsewhere in the laterite processing industry. Unfortunately, developments in Cuba removed the Moa Bay facilities from Freeport control. This deprived the project of a start-up that would have allowed thorough resolution of difficulties and a quicker attainment of production capacity. This meant lost opportunity to positively prove and complete the technology when optimum resources and staff were available. This paper reviews the original rationale of how design was developed via laboratory, bench scale and pilot studies by Freeport Sulfur. Some later operating problems will also be discussed. This case is unusual, but the lessons learned may be instructive in the application of difficult and complicated technologies, as well as the need to understand and retain access to the original development and design activities Keywords: Moa Bay, Freeport Sulfur, Port Nickel, acid pressure leaching, pilot plant, pachuca, Chemical Construction, pressure letdown, cobalt, titanium

Jan 1, 2004

By Mario H. Castro-Cedeno

"A design for a handheld MEMS chemical detector is proposed. The detector will be used to detect trace amounts of chemicals in air. It can detect drugs, toxic chemicals and/or explosives. The proposed detector will use ion mobility spectrometry (IMS), a technique that is well known for accuracy and has been used in the past in suitcase sized chemical detectors. The separation and detection of the chemicals occurs in the drift channel and the process was modeled using the finite element method and CoventorWare modeling software. A manufacturing process sequence for the drift channel is proposed and was demonstrated.IntroductionThe goal of this effort is to design, mode~ and prototype a MEMS chip that will be the key component in an ion mobility spectrometer (IMS). This technique uses and asymmetric potential to separate the various ion species in a stream of incoming air [1-4]. One advantage of IMS is its ability to separate chemical species from air at atmospheric pressure and temperature. This is a requirement for a simple to use handheld drug or chemical detector. IMS can be used to detect drugs, toxic chemicals and explosives and it is well known for accuracy in detecting very small amounts of chemicals. This chemical detection technique has been used in the past, but not in handheld detectors.One variant of IMS is the high-field asymmetric waveform ion mobility spectrometry or FAIMS [3]. The FAIMS process, shown in Figure l, works as follows: a gas sample is admitted into the instrument where gas molecules are ionized, typically by a weak radioactive isotope source, ultraviolet light source; and more recently through field emission. The ions move along the length of a channel while they are separated in the transverse direction by an asymmetric electrical potential. The potential, in the form of an asymmetric waveform, causes relative motion between the various chemical species. The species that hit the charged top and bottom plates are neutralized and only those ions that move along the center are detectable as charged chemical ions at the end of the channel."

Jan 1, 2004

By Dinesh P. Amalnerkar, Nagegownivari Munirathnam, Tirthalli Prakash, Katia Vutova, Vania Vassileva, Veliko Donchev

"A time-dependent model for electron beam melting and refining (EBMR) of different metals and alloys is developed. The model is 3D axi-symmetrical and an adapted numerical scheme of Pismen-Rekftord type is applied. The developed computer program computes the thermal fields in the metal ingots during EBMR process as well as the dynamics of the thermal streams and the geometry of the molten metal pools. Calculated results for different regimes of EBMR of titanium are obtained and discussed in the paper. Experiments are performed and impurities' concentration data are presented. Simulation results are compared with experimental data and are used for optimization of the EBMR process in the case of Ti.IntroductionElectron beam melting and refining (EBMR) has an important role in the special electrometallurgy[ 1-6] and it is approved for obtaining of pure titanium [7]. EBMR of metals and alloys is being recognized as a competitive and even the single method for obtaining new materials for all areas of human activity.The principal scheme of the EBMR drip process is shown in Fig.1. A thin layer of molten metal is formed on the front part of the feeding rod during the e-beam processing and generated droplets fall into the molten pool in the crucible where the ingot is formed. The refining is mainly realized at the boundary liquid metal - vacuum. There are three zones in EBMR (Fig.1) - on the front part of the feeding rod (zone I in Fig.1 ), on the surface of the generated droplets (zone II in Fig.1) and the surface of the molten pool in the water-cooled copper crucible (zone III in Fig.1)."

Jan 1, 2013