Search Documents

By D. K. Panda

The behavior of single drops with gas evolution at the interface is of interest because this is one of the important reactions that occur in oxygen steelmaking vessels, where a large amount of iron-carbon drops are dispersed in an oxidizing slag. The carbon dissolved in these drops, reacts with the slag to form CO, which is evolved as a gaseous phase. A room- temperature model was used to study the nature of this type of reaction including the effect of various factors such as viscosity and the presence of surface active impurities. Experiments were done for reacting drops over a wide size range to observe various regimes of behavior. Large single drops were levitated in a counter current flow to produce a sufficiently long residence time to allow the study of the various stages in the reaction. The emphasis of this work was to obtain photographic evidence of a high quality to describe all possible modes of behavior, and so a lot of effort was given to developing and perfecting experimental techniques.

Jan 1, 1994

By Xianzhong Hu, Qingbo Yu, Qin Qin

"Oxy-fuel combustion is one promising option among different CO2 capture technologies. The object of this work is to show the effect of CO2 dilution on the laminar flame speed, flame structure and reaction pathway for methane oxidation at O2/CO2 atmosphere. In this paper, kinetic simulations were made using CHEMKIN with GRI-Mech 3.0 mechanism, which was validated by experimental data of laminar flame speeds. The reaction pathway of CH4/O2/CO2 mixture was derived from reaction flow analysis. Results showed that CO2 decreased the flame speeds, lowed concentration of major intermediates and increased flame thickness. The major chemical pathways of CH4 to CO2 have not changed at O2/CO2 atmosphere comparing with O2/N2 atmosphere, but contributions to major intermediates formation from each related elementary reaction have changed a lot. In addition, the secondary chemical pathways of CH3 oxidation became different at O2/CO2 atmosphere.IntroductionNowadays, as the global economy is developing fast and the pollutant levels (especially global warming gases) are increasing, a lot of researches are focusing on new technologies which can cut greenhouse gas emissions [1]. New technologies have been developed, such as high Mild combustion, flameless combustion and Integrated Gasification Combined Cycle (IGCC) technology. Oxy-fuel combustion using carbon dioxide as dilution of oxygen is considered as a promising approach for reducing CO2 emission. The properties of CO2 in flue gas are different from N2 in air. On one side, the transport, thermal and radiative properties of CO2 are different from N2 in air. On the other side, CO2 is not inert but directly participates in chemical reactions and recent researches [2-5] also present the chemical effects of CO2 on oxy-combustion. For these differences above, the characteristics of oxy-combustion are not alike with traditional combustion. It is necessary to develop the investigation of oxy-combustion.In all combustion processes, laminar flame speed is an important parameter, which links to combustion behavior. Analysis of this parameter can provide a better understanding of the effect of CO2 dilution in the process of oxy-combustion. Several investigations of laminar flame speeds of oxy-fuel flame have been improved, including experimental measurements and numerical computations. A.A.Konnov et al. measured the flame speeds of oxy-methane and oxy-ethane mixture using the heat flux method with a flat burner [6-8]. V. Ratna Kishore et al. used heat flux method to measure the adiabatic laminar flame speeds of hydrogen [9] and H2/CO mixture [10]. Adiabatic laminar flame speeds of hydrogen in O2/CO2 atmosphere are much smaller than in O2/N2 or in O2/Ar. The burning velocity of H2/CO mixture decreased with increase in CO2 content in mixture. Jeongseog Oh et al. [11] used Bunsen flame to measure the laminar flame speeds of premixed oxy-methane mixture with angle methods in atmospheric condition (300k, 1atm). The results were SL=29.1cm/s and SL=29.5cm/s respectively derived from oxy-methane from CH* images and Schlieren photos."

Jan 1, 2014

By G. Mawire

The extraction of scandium from its oxide with a task specific ionic liquid [Hbet][Tf2N] offers potential advantages of lower energy consumption, recycling of the extractant and reduced environmental impact compared to conventional methods. In this paper, the influence of reaction temperature, solid to liquid ratio and water to the ionic liquid ratio on the extraction of scandium from a synthetic scandium oxide (Sc2O3) system was studied. The influence of investigated parameters on leaching was very significant as approximately 98% scandium was extracted from its oxide after 72 h. Furthermore, the ionic liquid also selectively extracted 47% scandium after 48 h from a mixture of pure metal oxides containing oxides of tantalum, niobium, and scandium. The research demonstrated the potential of [Hbet][Tf2N] to selectively extract scandium from columbite processing tailings and other scandium bearing ores like Ixiolite, Heftetjernite and Tantalite which predominately contain tantalum and niobium.

By Keizo Uematsu, Satoshi Tanaka, Nozomu Uchida, Ronne Hendrajaya

"The influence of microstructural defects on strength in Si3N4 is reviewed. The presence of cracks, pores and inclusions greatly affects the strength of Si3N4. The micron order crack size and distribution were quantified by micrographic technique. The observed defect size was range from 4 µm to 28 µm.The density of defect increases as the defect size decreases. The correlation between defects size and density was better represented on the logarithmic graph. The correlation was linier. IntroductionFracture in ceramics materials occurs from. In order to understand the relationship between strength and defects, it is necessary to examine the fracture process quantitatively.1In this study, the micrographic technique is used to determine the defects size and distribution in Si3N4. The observed data will be used to predict the material strength by using fracture mechanics rnodel.2Experimental ProcedureThe sintered Si3N4 specimens ( SNl, Japan Fine Ceramics Center) were sliced into 1mm thick . The both sides of specimen surface were polished into by using diamond slurries with particle size down to 2µm. The final thickness was 0.045 mm. The optical microscope (NIKON OPTIPHOT02-POL) was used to observed the internal defects with transmission mode. The reflection mode was used to determine the surface defects, so that the internal defect could be distinguished from surface defect. The measurement and counting was taken on the micrograph and the longest part of the defect was measured as the defect size. The size density distribution of internal defect is taken."

Jan 1, 2000

By A. F. Saavedra, N. E. Richards, C. J. McMinn

"The aluminum industry in general and Reynolds Metals Company in particular have continued to support development work for improvement of the Hall cell design and for alternative processes for the reduction of alumina. The evolution of the Hall cell design will continue into the next century as a result of further development of mathematical models, sophisticated control systems and new materials for cell components. This paper discusses the areas in which the new generation cell advances will differ from the present day design. Additionally, Reynolds Metal s has supported work for the development of a carbo thermic process to reduce alumina. Theoretical work has indicated that this process could possibly have economic advantage over the Hall process. Several complicated furnace configurations have been proposed to provide the conditions for successfully reducing alumina. The results of small pilot scale operation and most promising furnace design are discussed. For comparison, projected capital investment costs and operation costs are discussed. IntroductionThe evolution of the Hall-Heroult process will continue into the next century. This evolution will be influenced by economics, more .restrictive environment and worker protection requirements, and technological development. These factors will also cause changes in the competitive position of alternate processes for aluminum production.Several aluminum producers have made major investments in alternate processes for aluminum production in the past three decades and there is continued support in some companies for improvements in the Hall-Heroult process and for alternate processes. The more visible development work in reduction technology, not aimed at significant process changes, is in the areas of higher amperage cells with bus bar designs to reduce harmful magnetic effects, more advanced and automated feed, voltage and electrolyte composition control, improved energy efficiency and sol id waste disposal . Efforts to bring significant change to the reduction process are being made in development of materials that can function as inert anodes and cathodes. These materials could lead to the development of reduction cells with multiple bipolar electrodes operating on oxide feed and fluoride electrolytes. Development work on new processes was reduced in the last decade by several companies because of economic and technological realities. Reynolds Metals supported work on a carbothermic process to reduce alumina and produce commercial pure aluminum. This work progressed through small pilot plant operation, and resulted in development of furnace designs and operation regimes. This paper reviews how this and other technologies could influence the reduction of alumina beyond the year 2000."

Jan 1, 1988

By Roberto Parreiras Tavares, Frederico da Costa Fernandes, Guilherme Antonio Defendi, Vangleik Ferreira da Cruz, Júlio César de Sousa Pena

"Near-net-shape casting is an important area of research in the iron and steel industry today. Among the near-net-shape casting processes, the single-belt caster seems to be the most promising, since it is the only one that can achieve levels of productivity similar to those obtained with conventional continuous casting machines. One of the most important aspects in the single-belt casting is the feeding system used to deliver liquid metal over the belt. This system determines the velocity distribution and the levels of turbulence of the liquid metal and affects the quality of the strips. In the present work, a metal delivery system having a simple geometry was proposed. Using the CFD code CFX 5.6, a mathematical model to simulate three-dimensional turbulent fluid flow and heat transfer in that system has been developed. This model was used to analyze different configurations of the metal delivery system and the free surface shape of the fluid was also determined. A physical model of the feeding system was built and used to validate the predictions of the mathematical model. The fluid flow calculations have been validated by dye injection experiments and laser doppler anemometry. Measurements of the free surface levels have also been performed. These experiments provided supporting evidence for the predictions of the mathematical model.IntroductionTo maintain its competitiveness in the present market, the metallurgical sector, particularly the steelmaking companies, are developing new techniques of production. Some of these new processes are focussed on the strip casting technologies. Among these technologies, the SingleBelt process is considered the most interesting option, reducing the number of rolling steps and, consequently, the final cost of the product, especially the part associated to the energy consumption (fuel and/or electric energy). This process can also reach levels of productivity that can not be matched by other strip casting methods(1). One of the most important aspects concerning these new processes is related to the liquid metal delivery system. This system can have a significant effect on the final quality of the strips, since it determines the velocity distribution and the levels of turbulence of the liquid metal."

Jan 1, 2004

By Shivendra Sinha

Total pressure oxidation (TPOX) is widely outreached leaching practice for base metals from sulfide minerals, wherein high temperature (T ∼ 200 °C) and oxygen pressure (pO2 ∼ 25 bar) are required. These aggressive conditions intensify the oxygen mass transfer, and therefore facilitate metal dissolution. However, challenging-cum-negative aspects of such practice are energy and material intensive requirements and high oxygen demand. Thus, the present study explores the novel emulsified medium for enhancement of oxygen mass transfer, which assists faster metal dissolution at significantly lower temperature and pressure condition. It is possible to achieve quantitative dissolution (>95%) of Cu, Ni and Co from mixed sulfide minerals at T ∼ 95 °C and pO2 ∼ 2 bar using an emulsion of 2.5% (v/v) n-Hexadecane in dilute sulfuric acid. In addition, n-Hexadecane was found to be inert, stable and immiscible in a pressurized leaching system, thus can be easily separated and recycled in subsequent leaching stages. Thus, this study offers an energy efficient route for low temperature-pressure leaching of sulfides.

By Jewel Gomes

Green rust is an important intermediate in oxidative transformation of Fe(II) phase. This unstable compound contains a mixture of ferrous and ferric hydroxides that belong to a family of minerals known as layered double hydroxides (LDH). Its general formula is [FeII(6-x) FeIIIx (OH)12]x+[Ax/n-*yH2O] x-, where A is an n-valent anion mainly Cl-, CO3-2 and SO4-2, and in which either the bivalent or the trivalent iron can be replaced for other trivalent or bivalent metal ions. It was first identified as corrosion product, later in soils as a product of interactions between microbes and metals in soils. Due to its high reactivity, it is used in the reduction of organic and inorganic compounds, As removal, and the treatment of acid mine drainage. In this paper, we described the method of electrochemical generation of green rust, its characterization by XRD, SEM and FT-IR, and its implications to electrocoagulation.

Jan 1, 2009

By P. A. Manohar

This paper describes an implementation of the Potts model for simulation of grain growth in 2D on a distributed-memory parallel architecture. The simulation scheme utilizes a continuous-time, asynchronous parallel version of the n-fold way algorithm. Each Processing Element (PE) carries a piece of the global simulation domain while the virtual topology of the PEs is in the form of a square grid in 2D and Torus in 3D. Different PEs have different local simulated times. Inter-processor communication is carried by the Message Passing Interface (MPI) routines. Sample results for grain growth simulation in 2D are presented for a 840 x 840 global domain size distributed over 16 PEs. The grain growth kinetics obtained in the simulation of pure, isotropic systems is in good agreement with the theory. Grain size distributions obtained in the parallel simulation are well described by the lognormal distribution, thus validating the simulation procedure. Keywords: Metropolis algorithm. n-fold way algorithm, asynchronous parallelization, grain growth

Jan 1, 2003

By T. J. White

A synthetic Mineral Immobilization Technology (SMITE) has been developed for stabilizing municipal and hazardous waste incinerator ash. Tailored additives are introduced to the ash in a' first stage that pre-stabilizes all the toxic metal components in non-volatile forms. and in a second pyrometallurgical stage, these are converted to insoluble mineral analogues. It has been found that a combination of apatitie. spinal, anhydrite and monazite can immobilize all the ash components at high waste loading and high density. Typically the stabilized products contain in excess of 50 wt% ash and have densities of 2.5- 3.0 g.cc-1. Toxicity Characteristic Leach Procedure (TCLP) testing has demonstrated that the products well satisfy regulatory requirements. The cost of production and disposal of SMITE waste forms in 2-5 less expensive than. convential methods of solidification/stabilization. This paper will describe the principles of SMITE design for ash stabilization, outline the fabrication procedure, and present comprehensive microstructural and chemical data to validate waste form performance.

Jan 1, 1996

By Ali Hasham

Reduction rates of FeO in CaO-SiO2-Al2O3 slags by Fe-C melts have been investigated experimentally at 1723 K. The rates were estimated using experimentally determined CO(g) evolution rates. Flash X-ray images were employed to visualize the behavior of the melt-slag interface during the reactions. The influence of melt interface was examined by conducting two types of experiments - (i) dropping one (or several) Fe-C droplet(s) weighing 2 g into the molten slag bath, and (ii) dropping a small amount (10-30 g) of slag onto a Fe-C melt weighing 400 g. The rates from both types of experiments were compared and analyzed to determine the rate limiting steps. It was established that neither the carbon transport in the Fe-C melt, nor the transport of gas species in the gas film adjacent to Fe-C melt was responsible in limiting the reaction rate. It is possible that the slag phase mass transport may be controlling the initial reduction rate in the droplet experiments. However, a, different mechanism was responsible in limiting the reduction reaction when the overall %C in the droplets fell to about 2-3.

Jan 1, 1992

By K. Ohmori, K. Takeya, S. Yoshizawa, A. Kawamoto, T. Ishikawa

"High performance Sm2Fe17N3 magnet powder is developed nitriding Sm2Fe17 alloy that 'is made using a reduction and diffusion method. Typical remanence, coercivity and maximum energy product of the fine powder are 1.40 T, 1.13 T and 323 kJ/m3, respectively. Decreasing samarium content, oxygen content and the amount of a-Fe are found to be the important factors to realize high-energy product.High performance injection molded Sm2Fe17N3 anisotropic magnet is also developed using the powder and an original binder system developed in order to mold at low temperature. Typical remanence, coercivity and maximum energy product obtained are 0.77 T, 0.78 T and 103 kJ/m3, respectively in the density of 4.77 Mg/m3The temperature coefficient of remanence is -0.07 %/K and that of coercivity is -0.54.%/K. The initial irreversible flux loss of the magnet that has a permeance of two is -5 % at 100 °C and the irreversible .flux loss of it is -4.4 % exposing it at 80 °C for 1000h.IntroductionSm2Fe17N3 alloy powder is expected to be very useful for a bonded magnet. The reasons are as follows. The magnetization is as large as the Nd2Fe14B alloy. Curie temperature is even higher than the alloy. The uni-axial anisotropy is comparatively higher than the alloy. Consequently it is possible to obtain high coercivity after just milling the powder and therefore possible to obtain high-energy product in a bonded magnet as it is realized in the SmCo5 bonded magnet. On the other hand, sintering is difficult because it will be decomposed into samarium nitride and a-Fe when heating it up to 500°C:"

Jan 1, 2000

By W. G. Davenport

Chapter 6 examined autotherrnal smelting of pure chalcopyrite concentrate with 50 mass% O2-50 mass% N2 blast. It showed that production of 1500 K products with this blast requires: 181 kg of pure oxygen 337 kg of air per tonne, of concentrate. It also showed that the grade of matte produced with this blast is 58% Cu. This chapter re-examines autotherrnal smelting by asking: (A) WHAT COMPOSITION BLAST (MASS% 02 -MASS% N2), 298 K, WILL AUTOTHERMALL Y PRODUCE 65% Cu MATTE 1500 K FROM PURE CHALCOPYRITE CONCENTRATE? (B) HOW MUCH PURE OXYGEN AND AIR WILL BE NEEDED? These are important questions for flash? smelting because furnace operators usually want to send specific composition matte to converting. This chapter shows how a specified matte can be produced autotherrnally with 298 K oxygen-air blast. Later chapters show how it can be done with hot blast, hydrocarbon combustion, different concentrates etc.

Jan 1, 2001

By Caisa Samuelsson

Experimental studies in laboratory-scale equipment have been carried out to study the vaporisation from dust generated during the copper converting process. In the present work the vaporisation of Zn, Pb, As, Sb, and Bi from a dust collected in the electrostatic precipitator after the copper converter were studied. The results show that Pb, Bi and As were vaporised to a high degree from the dust at a temperature above 900°C in a gas containing N2, SO2 and a small amount of H2. The vaporisation was high for these elements also in a gas containing N2, SO2 and 02 at temperatures above 1120°C. In an earlier study, thermodynamic calculations showed that it is possible to selectively condense metals at high temperature' in a gas atmosphere generated during a copper converting process. The present study was carried out to verify the thermodynamic model. The results indicate that it should be possible for a selective condensation of Zn at high temperature. The temperature required for a selective condensation of Zn is dependent upon the gas atmosphere, e.g., the oxygen potential.

Jan 1, 1998

By I. A. Ibrahim, A. K. Ismail, A. A. I. Afifi

"Synthetic rutile for paints industry is conventionally produced by a combined smelting and leaching process. Smelting process is an energy intensive step and represents economic burden in view of the increasing energy costs. Egyptian ilmenite ore containing 40% TiO2 and 38% total Fe was thus directly leached with sulphuric acid to produce eventually synthetic rutile. The process-involves digestion of the ore with sulphuric acid whereby both TiO2 and Fe are dissolved. The solution was then treated with iron powder to convert Fe3+ to Fe2+ to avoid co-precipitation of iron during the hydrolysis step. After solid/liquid separation and clarification, Fe was crystallized as ferrous sulphate hydrate by chilling. The titanium pregnant liquor was concentrated by evaporation and then hydrolyzed to precipitate hydrated titanium dioxide which was then calcined to produce synthetic rutile containing 98.6 TiO2 and 0.58% Fe2O 3. The optimum conditions of all the processing stages were determined.IntroductionSynthetic rutile for paints, welding rods and other industries could be produced from ilmenite ore by sulfuric acid leaching process. This process is a batch process and nearly 80% of all TiO2 produced in the world is made by this process [1]. Figure l shows simple block flowsheet of the process. The process involves the following stages.Digestion: In this stage, ilmenite ore is treated with concentrated sulfuric acid where both iron and titanium are converted to their respective sulfates according to the following equations:"

Jan 1, 2000

By Tadashi Aiura, Yasuhiro Miura

"A small amount(0.2mass%) of Scandium(Sc) was added to the 7.NOl and 5083 Al alloys as a refiner and stabilizer of microstructure, and the resulting microstructures were discussed in comparison with the effects of the conventional additives. The followings are summarized: 1) in the as-solidified structure, a ·decreased tendency of constitutional supercooling and increased solubility of Mg were recognized for the Sc-added 5083 alloy. Sc is a -better microstructure refiner for the 7N01 alloy than Zr, in a sense that it does not suppress the favorable effect of· coexisting Ti. 2) Sc effectively suppresses recrystallization both in the 5083 and 7N01 alloys. 3) The rod like primary Al3Sc crystals formed during solidification, as well as the fine dispersion of Al3Sc precipitates formed by subsequent heat treatment, can act as a strong recrystallization suppresser. IntroductionThe 7N01 and 5083 alloys are the most popular industrial Al alloys and they are widely' used for various structures because of their superior properties. Fine macro and micro structures of the materials are required for obtaining acceptable sec resistance,consistent appearance of anodized surface and good weldability, as well as good mechanical properties. In order to produce fine grain structures, transition metals, such as Cr, Zr, and Mn, have been conventionally added.It has been reported that Sc is an efficient refiner [l, 2] and can be an alternative for the conventional and also suppresses recrystallization in Al alloys [3,4]. Scandium is the lightest transition element and forms an equilibrium intermetallic phase. The equilibrium phase, Ll2-Al3Sc, is coherent with the matrix, and of _spherical shape. A fine dispersion of the spherical precipitates is obtained by quenching and aging after solutionizing annealing. The authors have already reported a part of the experimental results on the effect of Sc on the as homogenized microstructure of the 5083 alloy [5]. In the present study, the effects of Sc on the macro and micro structures of the industrial high strength Al alloys(7N01 and 5083) for extrusion are investigated, and the superior role of Sc as a grain refiner is shown"

Jan 1, 2000

By I. Gaballah

Jarosite contains up to 15 % of heavy metal compounds 'HMC'. The current waste disposal methods will not be allowed in the near future due to new environmental regulations and pollution risks. For these reasons, thermal treatments of raw or decomposed jarosite, in controlled atmospheres, were investigated. The aim of these treatments is to decontaminate the jarosite and/ or to recover the HMC for recycling. According to physico-chemical characteristics of the samples, the thermal treatments in controlled atmospheres N2, CO+N2 and C12+air lead to the extraction rate that vary from 93 to 98 %. Heavy metal compounds were separated by cooling the gaseous phase. The treatments' residue was almost free from HMC. Between 700 "C and 800 "C, the chlorinating treatment was successful of eliminating more than 97 % of HMC contained in four different samples.

Jan 1, 1999

By Michael S. Moats, Scott C. Campin, J. Brent Hiskey

"Electrochemical techniques are a valuable means of analyzing the passivation of commercial copper anodes. Electrochemical impedance spectroscopy (EIS) provides information concerning transport and reaction phenomena occurring at an electrode surface. Commercial. copper anodes of varying compositions have been examined using EIS. Experiments were conducted in a flat cell with an electrolyte of 40 gil Cu2 + and 160 gil H2S04 maintained at 65 DC. Impedance spectra were obtained at the potentials characteristic of the open circuit voltage and passive region for each anode. The spectra of the passivating films exhibited a flattened resistive/capacitive loop at middle to high frequencies and an inductive loop at low frequencies. An equivalent· circuit utilizing an inductor-resistor series in parallel with the double layer capacitance and charge transfer resistance was adequate in modeling the impedance data. The influence of anodes impurities on the components of the equivalent circuit is discussed and correlated with a hi-layer passivation model.IntroductionPassivation of copper anodes during industrial electrorefining has received considerable attention in the past few decades. Great strides have been made in understanding the roles of anode impurities [1-25], electrolysis parameters [20,26], and electrolyte chemistries [20,26]. Even so, passivation still occurs even in the most modem of refineries. The exact cause of passivation is not fully understood. It is known that the anode surface becomes covered by a passivating film. This film has been proposed to be CuS04'&5H20, Cu20, or mixed oxides. The localized concentrations of Ft, Cu+, and Cu2+ ions determines which phase is more favorable. The presence of these ions is controlled by the reaction kinetics and diffusion of species through the slimes layer.Reaction kinetics between Cu, Cu +, and Cu2+ are based on the dissolution mechanism of copper. There exists four different models to describe the dissolution of pure copper. The classical model of Mattsson and Bockris [27] involves two single electron transfers with the cuprous-cupric reaction being the rate detennining step. More recently, Wong, Collier, and MacFarlane [28] used ac impedance to elucidate a more complex mechanism involving the affect of pH and anions. Their findings indicate that the formation of cuprous ions in solution, Cu(I)so~ is favored over Cu(1I) ions adsorbed to the electrode surface in the presence of sulfate and as pH increases from pH 1 to pH 5."

Jan 1, 1997

By T. K. Mukcherjee

The importance of the processing of secondary resources such as solid industrial wastes and liquid effluents as well as byroducts for the recovery of the associated metal values hardly needs any elaboration. Such processing contributes in no small measure.towards the augmentation of the availability and the supply position of resources. As an added benefit, it leads to a reduction in environmental pollution caused by the undesirable waste materials. As some typical examples of secondary resources in the Indian scenario, mention' can be made of spent catalysts, metal/alloy scrap, ash, consumed batteries, flue dust, slag, sludge and slime, pickling solutions, spent acids; plating rinse solutions, spent etchants, waste water from synthetic fibre manufacture and from tanneries etc. These wastes constitute a source of a variety of non ferrous metals. In the processing of secondary resources like these, the techniques of hydrometallurgy such as solvent extraction play a pivotal role. This paper outlines the efforts made to use solvent extraction to recover(1) base metals. such as copper, zinc, nickel and cobalt from a number of secondary resources like cake, and sludge(2) refractory metals like molybdenum and vanadium from sulphidic byproducts and spent catalyst and (3:) nuclear metal like uranium from phosphoric acid. In the case of base metals, process flowsheet involving the use of acidic extractants such as DEHPA and PC88A have been optimised. The problem of iron removal from the leach liquor, "which influences the metal recovery process significantly, has drawn a special emphasis. hi the case of refractory metals, basic extractants .like Alamine 336 has been pressed into service to produce kilogramme. quantities of pure salts of molybdenum and vanadium, Finally, the paper gives a brief account of plant experience in recovering uranium from phosphoric acid, using 'a solvent system comosed of DEHPA and TOPO.

Jan 1, 1996

By Y. Yang, S. Peelman, J. Sietsma, Z. H. I. Sun

The rare earth elements (REEs) present in the Kiruna iron ore mine tailings are being considered as a new REE resource for the EU. These tailings, after beneficiation, contain approximately 5000 ppm of rare earths, concentrated in apatite and monazite minerals. To economically extract the REEs from these tailings the phosphorous contained within the apatite must also be extracted and the waste production of the process should be minimal. To achieve the extraction of REEs and phosphorous HCl and HNO3 were investigated as possible leaching agents. Based on the results a leaching process using HNO3 is proposed. This process produces H3PO4 from the apatite while simultaneously dissolving the REEs. The resulting leach liquor is then cooled to remove the unwanted Ca as Ca(NO3)2. Analysis of the leach liquor reveals extraction ratios of between 75% and 100% for the heavy REE (e.g. Y, Eu, Dy, …) and below 40% from the light REEs (i.e. Ce, La). Full phosphorous extraction was also achieved.

Jan 1, 2016