Search Documents

By Johan Sundström

Anhydrous DyC13 was prepared by dehydration of DyCl3?6H20 in a fluidized bed using both batch- wise and continuous feeding. A gas mixture with varied composition of argon and HCl was used. The productivity was high, reaching values of 0.25 mol H20/m2-st during the reaction step 6- 1 and 0.062 mol H2O/m2.s during the reaction step 1-0. The product was free from hydrolytic compounds, such as DyOCI, if control of inlet gas composition versus temperature was achieved. From the results of various experiments, some relations between HCI-concentration and temperature in order to avoid hydrolysis have been deduced. The fluidization process efficiency decreases drastically after the dehydration has proceeded down to about 10 mol% of remaining water. Therefore, in a final treatment the last traces of water were removed by slowly purging gas through a packed bed. The water content could thereby be reduced to less than 1 mol%.

Jan 1, 1997

By N. S. Narayanan

Monazite, one of the major sources of rare earths, is normally opened by digestion with hot concentrated caustic soda solution. Caustic digestion dissolves phosphate and leaves a hydrated mixed metal oxides cake containing thorium, uranium and rare earths. By leaching this cake with hydrochloric acid at pH 3.0 to 3.2 bulk of the rare earths are preferentially removed and separated. The slurry left after removal of major portion of rare earths contains all the thorium and uranium present In the feed monazite. In addition this slurry also contains substantial quantities of rare earths. Solvent extraction tests were carried out to develop a process to separate rare earths, thorium and uranium present in the mixed chloride solution obtained by dissolving the above slurry in hydrochloric acid. Based on these tests a solvent extraction flow sheet was developed with di-2-ethyl hexyl phosphonic acid mono 2-ethyl hexyl ester as the extractant. The details of experimental work and results obtained are discussed and a flow sheet for processing monazite Incorporating the new process is suggested.

Jan 1, 1997

By W. D. Cho

Fast dissolution of nonmetallic inclusions such as alumina particles in molten slags has been required in secondary steelmaking -ladle and tundish - to minimize the amount and the size of nonmetallic inclusions in steel products. In the present work, the dissolution behavior of alumina particles in molten CaO-A12O3 and CaO-A12O3-SiO2 slags at the temperatures between 1450 and 1550°C have been investigated in terms of kinetics and mechanism. Alumina particles were added directly into the slags and the variation of the particle size with time was determined using optical and electron microscopies. The conventional types of slag for ladle and tundish were included in the dissolution study. The effects of Al2O3, Siq, CaF2 and MgO contents on the dissolution rate of alumina particles have also been determined. The diffusion boundary layer between alumina particle and bulk slag phase has been observed and analyzed using SEM and EDS. Based on the analysis of kinetic data and the boundary layer, the dissolution mechanism has been discussed.

Jan 1, 2002

By Kwan Soo Han

A thermodynamic model for predicting the distribution coefficients has been developed by taking into account the extraction mech-.ism and the chloride complexation when Sm, Eu, Gd, Tb, Dy and Ho for single component systems are extracted from acidic chloride solutions by di-2-ethylhexyl phosphoric acid and 2-ethylhexyl phosphonic acid mono-2-ethylhexyl ester in kerosene, respectively. The model equation includes two constants, of which one corresponds to the apparent extraction equilibrium constant and the other is due to the variation of the activity coefficients of organic species. These values are determined from a few experimental data by the curve fitting method Then, the distribution coefficients under untried conditions have been predicted from only the initial data by iterative calculations. Bromley's formulation is used to estimate the activity coefficients of aqueous species and the interaction parameters for some rare earth chlorides are reported in terms of molality and molarity using data from Spedding et al. The validity of this method has been confirmed by excellent agreement between the experimental and the predicted distribution coefficients.

Jan 1, 1989

By Cheng Pan, Xuewei Lv, Guibao Qiu, Chenguang Bai, Meilong Hu

"Physic-chemical properties of slag at high temperature play an important role in the pyrometallurgical process of production of ferronickel alloy. It determines the operation efficiency, metal recovery ratio, energy consumption and the distribution of elements like S and P between the slag and metals. In the present work, the effect of MgO content in the slag on melting features and viscosity of the slag was investigated. The MgO content in the SiO2-CaO-MgO-Al2O3 -FeO in the quinary slag system varied from 14.5% to 22.5%. The results shown that all slag samples begin to softening at the same temperature, the softening temperature, melting temperature, flowing temperature decrease with the increase of MgO content when the MgO content is in range of 14.5 and 20.5 pct mass, and when MgO content up to 22.5 percent, the temperatures increase sharply. Besides the inflection point temperature of viscosity-temperature curve increase with the increase of MgO when the MgO content is in range 16 and 22.5 pct mass.IntroductionNickel is very important to modern society, without it, we would not be able to share many things in our daily life, such as airplanes, computers and many stainless steel appliances in our homes and workplaces1.. It is the essential element of the stainless steel making, and about 65% of the nickel consumed in the world is used to make stainless steel2., so with the increase of stainless steel, the nickel production and demand has continued to increase3.Nickel is produced from two distinct ore types: nickel sulfide deposits and oxide nickel laterite deposits. The great majority of world’s known nickel resources are contained in laterite deposits3.. The laterite ores are normal classified into two groups: the high-iron laterite ore and high-magnesia laterite ore1. Typical composition of high-magnesia laterite ore is in the range 1-3%, and these ores are suitable for pyrometallurgical process to produce ferronickel4."

Jan 1, 2012

By Zhang Libo, Li Wei, Peng Jinhui, Guo Shenghui, L. Jing

Partially stabilized zirconia ceramics (PSZ) were prepared by microwave sintering using natural baddeleyite which was obtained by flotation of baddeleyite ore as starting materials. Because of using natural baddeleyite as raw and the process producing no waste, it realized shorter process, energy savmg, environmentally-friendly and non-damage processing. In this work natural baddeleyite stabilized with 3.8wt.% CaO were sintered at 1300°C for 60min in a multi-mode 2.45GHz microwave furnace. Microwave sintering could fast heating and sintering. Besides that, microwave sintering could heat materials wholly, low the sintering temperature, improve the materials properties and save energy. X-ray spectrum displayed the product composed by the tetragonal phase and monoclinic phase that also showed the product was PSZ. Fine and uniform microstructures were observed in the product through scanning electron microscopy. PSZ which was with high density was confirmed by the method of the Archimedes technique.

Jan 1, 2011

By Ki Joo Sim, Sung Beom An, Joonho Lee, Minsoo Shin

Valorization of the electrical arc furnace oxidizing slag by coke was carried out by the reduction of iron oxide in the slag. Since the reduction of iron oxide by solid carbon is an endothermic reaction, supply of heat energy is required. In addition, slag has a low thermal conductivity; traditional fuel injection is not suitable for this reaction. Microwave can be used to supply heat energy to the system. Commercial oxidizing slag was reduced by coke under the microwave irradiation (1.7 kW, 2.45 GHz). The maximum recovery ratio of iron was 87%. In addition, slag composition modification was attempted to use the remaining slag for a mixture in cement clinker. Free-CaO in the slag was successfully suppressed, and the use of the remaining slag as a potential mixture was confirmed.

Jan 1, 2014

By XUEWEN WANG, Bowen Li, Mingyu Wang

A novel technology characterized by higher extraction of vanadium and recovery of valuable elements was developed to recover vanadium from stone coal. The brief flow of the novel technology mainly includes low temperature sulphation roasting, water leaching, recovering potassium, aluminum, copper and selenium, solvent extraction enrichment vanadium, precipitation of red vanadium, removal sodium from red vanadium and calcinations. The total recovery of vanadium reached 76.3%, which was higher than the current applied technology. The novel technology was environmentally-friendly and could extract vanadium from the stone coal, in which the content of V2O5 was less than 0.8%.

Jan 1, 2015

By Haotian Xue

A new process to extracted antimony directly from stibnite concentrate by reductive sulfur-fixation smelting in sodium molten salt has been presented. The influences of sodium salt content and composition, ferric oxide addition, temperature and time was investigated, respectively. The optimum conditions was determined as follows: W????: ??concentrate=40%, W??alt: ????concentrate =88.75%, WFe2O3 :Wconcentrate =55.13%, W??aCl: ????alt=40%, 1123K, 1h. Under above-mentioned optimum conditions, the average direct recovery ratio of antimony can reach 91.48%, and the main chemical composition of obtained crude antimony is Sb 94.31%, Fe 4.436%, Pb 0.502%, Au 0.0236%. In comparison to traditional antimony pyrometallurgical process, the smelting temperature of present process is reduced from 1423~1473K to 1123~1173K. During the smelting operation, SO2 emision can be avoided completely due to sulfur-fixation as FeS. Furthermore , S0 can be obtained when the molten slag is handled by water leaching with conditions of 323K, L/S=5/1, 2h.

Jan 1, 2014

By Jin Liu

In the early 1990?s, Inco successfully installed two new flash furnaces as part of their SO2abatement project to reduce SO2 emissions from the Copper Cliff Smelter by 60%. The flash furnace off-gas is cooled and cleaned through two new Monsanto Dynawave gas cleaning systems that replaced the traditional venturi scrubbing system. It was discovered that the flash furnace production capacity is often limited by the capacity of the gas cleaning system. The key task is to eliminate pressure drop from the system. The froth column is responsible for by far the largest pressure drop in the gas cleaning system. Initially, the column was fitted with 22 plates. In 1994, both #1 and #2 froth columns were modified by reducing the number of plates in each column from 22 to 18 and increasing the interplate spacing on lower plates. With increasing demand for more throughput in the flash furnaces, further modifications on the froth columns were made in 2005. This paper describes these modifications and results together with some fundamental analysis of the froth column characteristics.

Jan 1, 2006

By Jorge Alberto Soares Tenório, Romano Espinosa, Felipe Fardin Grillo, José Roberto de Oliveira, Denise Crocce

"The aim of this work was evaluation of the recovery of Zn and Fe of the EAFD added to the hot metal in the form of briquette at temperature of 1500°C. The EAFD was agglomerated by cold briquetting and introduced in the hot metal. This study utilized a bench-scale equipment to melt, during this process to kept a flow rate of inert gas above the bath. Were collected periodically metal samples and the samples were analyzed for determination of the content of total silicon and carbon by chemical analysis. Zinc oxide, zinc ferrite and other oxides were reduced and were volatized and collected by a cleaning system of dust (baghouse) located on top of the oven. More than 98% of iron were recovered from EAFD during the test. It was possible to produce a dust containing about 68% zinc by means of adding of EAFD.IntroductionIn the first semester of 2010, steel production was about 706 million tons, 27.9 % more than in the first half of 2009. Not a significantly increase if 2010 data is compared with the first semester of 2007 (only 7.2 % higher), before the world’s economic crises. Steel production is divided into two main routes. The first one, and most used, is the Basic Oxygen Furnace Process (BOF process), which in 2008 accounted for approximately 67.1 % of steel production. The second route is carried out in the Electric Arc Furnace (EAF) that in 2008 represented 30.6 % [1 ].Electric arc furnace dust (EAFD) is a solid waste generated during the steel making process. It is classi?ed according to NBR 10004 as dangerous solid waste-class I, because the elements Pb e Cd leach in water exceeding the maximum limits permitted by the NBR 10004 [2 ]."

Jan 1, 2012

By Naixiang Feng, Shaohu Tao, Zhihui Wang, Yuezhong Di

"A novel vacuum aluminothermic reduction lithium process was developed in present work which used lithium carbonate, alumina and calcium oxide as raw material. The process mainly contained three steps. The first step is that LiA102 clinker is prepared in ambient environment, then metal lithium is vacuum extracted from LiAl02 clinker with aluminum power as reducing agent, and the last step is that alumina is leached from the reduction residue with a mixture of sodium hydroxide and sodium carbonate. The results show that the lithium reduction ratio can be over 95% under the conditions of reduction temperature 1423K, reduction time 3h, and aluminum excess 20%. The main components of reduction residue are CaO· Al203 and 12Ca0·7Alz03. The alumina leaching rate of calcium aluminate in residue is over 80%. High-whiteness aluminum hydroxide can be obtained by carbonation precipitation of the reduction slag leaching solution.IntroductionWith a density about half of water, lithium is with the lowest density of all solids, mere 0.5 g/cm3 at 20 °C [l]. Lithium is widely used in aerospace, aviation, nuclear-generated power and electric battery industry. Nowadays, over 90 % of the world's primary lithium is produced by molten salt electrolysis [2-4]. But the development of molten salt electrolysis will be effected by some factors: cost, environment, and so on. Vacuum thermal reduction may be used extensively in future because of its low-energy consumption, high-purity and short-cycle."

Jan 1, 2013

By John O. Burckle

For years, the measurement of fugitive emissions from the primary copper converter has defied all attempts based on inferential measurements, It has been concluded by virtually all investigators that the only dependable tech¬nique to measure these emissions would be to completely enclose an operating converter to permit the capture and measurement of all emissions. However, complete enclosure with a metal hood is difficult; many of the most serious fugitive emissions result during periods when the converter must be attended with crane-operated equipment. This approach would require either opening of the enclosure to permit the entry of large items of equipment or completely new methods for charging and tapping converters' The installation of the air curtain hooding system at ASARCO's Tacoma smelter has permitted a quantitative approach to the direct measurement of the fugitive for the first time. In this program, the fugitives captured by the air curtain were measured at a downstream sampling point in the exhaust side of the air curtain system during the various portions of the converter cycle. Emission factors were established for sulfur dioxide, filterable particulate (method 5), inhalable particulate, and selected trace elements.

Jan 1, 1983

By S. Mondon

Hibi Smelter which is a Copper Smelter lining a blast furnace, produces 2,700 metric tons of anode copper per month. Generally, in a copper refinery, arsenic and antimony are considerably troublesome impurities. With regard to the elimination of antimony, Hibi Smelter has two handicaps described as follows. (1) Smelting under the slightly oxidizing atmosphere in the blast furnace. (2) Recycling the converter slag to the blast furnace after cooling. Therefore antimony and arsenic, mainly antimony, elimination tests, in which the alkaline flux was injected through the two tuyeres in the blowing stage, were carried out in the rotary anode furnace. Antimony and arsenic were respectively removed more than 90 96 from the molten copper, and their high eliminations are discussed by application of the transitory and permanent reaction model with the flux injection, which was presented by T. Lehner.

Jan 1, 1983

By Mingming Zhang, Mallikharjuna R. Bogala, Ramana G. Reddy

Steelmaking desulfurization slag samples were characterized using chemical, X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive spectrometry (EDS) methods. The objective of this work is to investigate the occurrence of sulfur and phosphorus components in the slag samples and to identify their origin and associations with the iron phases. Thermodynamic calculations results confirm the presence of phosphorus and sulfur components in the slag sample at high temperatures (1400 to 1800oC). The main constituents of slag include Ca3SiO5 (28.1%), MgO (9.31%), Ca3(PO4)2 (9.18%), CaS (8.39%) and CaO (5.68%). The major phosphorus and sulfur components of the slag are Ca3PO4 (99.2%) and CaS (79.3%) respectively. Characterization studies indicate the presence of microparticles of different sizes and shapes in the slag sample. Elemental analysis of these particles confirm the presence of major elements (O, Mg, Al, Si, S, Ca and Fe) in the slag sample.

Jan 1, 2015

By Jinxia Nie, Yunnen Chen, Dachao Zhang

"Rare earth resources are strategic and non-renewable resources. But disordered exploitation on rare earth metals leads to resources waste, environmental pollution and ecosystem destroyed. In this paper, soil collected from garden was cultured in thermostated incubator. Adding exogenous rare earth to the soil and the effects of recombination action of rare earth lanthanum, cerium and yttrium on soil enzymatic activities were studied. The results showed that single metal La and Ce can increase urease activity, but Y inhibits its. Coexist La/Y or La/Ce in soil inhibit the urease activity, coexist Y /Ce or coexist three metals promote its. Single metal La, Y and Ce can promote catalase activity, and that of coexist three metals. Pairwise coexist La, Y, Ce in soil inhibit catalase activity. With certain concentration of rare earth recombination action, urease activity in soil has been very significant direct proportion to ionic impulse, but catalase activity been insignificant inverse proportion to its.1. IntroductionThe increase of rare earth element content due to anthropogenic inputs frequently takes place in agro-industrial areas, leading to soil pollution episodes that may cause serious environmental problems because of their potential toxicity to microorganisms, plants, animals and human beings [ 1]. China is abundant in lanthanides resources. Rare earth metals are used in many frontier technologies such as photic devices, magnetic materials, and fine ceramics, and the amount of the rare earth metals used in these industries has been increasing. In addition to their use in industry, rare earth metals are more widely applied to cropland as microelement fertilizers due to their ability to promote growth and productivity of some crops [2]. As a result, more and more rare earth metals are moving into the ecosystems. While a permanent contamination of soils results in populations of micro-organisms with high resistance to rare earth metals, a short-term burden of contaminants at high concentrations could exert inhibitory effects on microbial carbon [3]. They accumulate in soils, bioaccumulate in crops, and enter the food chain, causing a potential problem of rare earth metals environmental pollution in China [4]. This contamination may also severely influence organisms and soil activities [5]."

Jan 1, 2011

By J. F. Elliott

The thermodynamic behavior of sulfur and oxygen in copper matte has been measured by equilibration of the melt 00 a gas consisting of CO, SO2 and Ar. The oxygen potential ranges from 10-9 to 10-7 and that for sulfur from 10-4 to 10-2 atm. The work is a continuation of the earlier study by Luraschi and Elliott in our laboratory. A model has been developed that permits extra-polation of the results to ascertain compositions of the matte that are saturated with various oxides of iron.

Jan 1, 1983

By Hongbo Zhu, Jinhui Peng, Linqing Dai

"To optimize the process variables for making direct reduced iron (DRI) by microwave heating, the reduction temperature, reduction time and the ratio of coal to material were studied with the central composite design (CCD) and their interactions on the Metallization rate were also investigated. The predictive polynomial quadratic equations model was analyzed by ANOVA. Optimal conditions of making DRI can be concluded as follows: 28 min at 1139?, the ratio of coal to material is 20.95%. Under these conditions, the metallization rate is up to 97.06%.1. IntroductionThere are some technical problems in making direct reduced iron (DRI) or sponge iron using iron ore concentrates containing coal and lime. In reduction of the iron ore concentrates containing coal with microwave heating, the strength of pellets needn’t to be considered. It reduces the costs and improve quality of materials, but also eliminates the need for pellet preparation process, simplifying the process and achieving a cleaner production.Microwave energy is a clean energy, and has characteristic of selective heating. The speed of heating is also fast. It researched by Chen Jin that when the mole mass of C: O is 0.627 and the microwave power is 15KW, it only spends 15min from 15? to 1021.6? with 1 kg iron ore containing coal with microwave heating [1]. There are many factors affecting metallization rate. In order to find a suitable condition for reduction process, it is necessary to design a series of suitable experiments.Response surface methodology (RSM) is one of the relevant multivariate techniques which can deal with multivariant experimental design strategy, statistical modeling and process optimization [2–5]. It is used to examine the relationship between one or more response variables and a set of quantitative experimental variables or factors. This method is often employed after the identification of the vital controllable factors to find the factor settings that optimize the response. Designs of this type are usually chosen when a curvature in the response surface is suspected. The process optimization of the microwave reduced iron ore was seldom reported in literature. Hence the present work intends to assess the effects of variables such as reduction time, reduction temperature and the ratio of coal to identify the optimum conditions using a central composite design (CCD). The characteristic of product was assessed using scanning electron microscope (SEM)."

Jan 1, 2011

By P. Chris Pistorius

"Use of coke in blast furnace ironmaking is the main origin of carbon dioxide emissions from integrated steelmaking. Use of pre-reduced iron feedstocks would reduce the coke rate and, if pre-reduction were carried out with natural gas, would decrease the overall carbon intensity of ironmaking. Blast furnace productivity would also increase, because the blast volume per unit of hot metal would decrease. This paper shows that these trends can be predicted quantitatively, by using a conceptually simple Rist-style blast furnace mass and energy balance, assuming furnace productivity to be limited by the tuyere gas flow rate. Such predictions would assist in optimizing the choice of the degree of reduction and relative amount of pre-reduced blast furnace feed.IntroductionSteelmaking is responsible for some 5% of world CO2 emissions, at a rate of approximately 1.9 tonnes of CO2 per tonne of cast steel [1]. In integrated steelmaking, the ultimate source of most of the CO2 emissions is coke, the indispensible (and expensive) fuel and reductant for blast furnaces. There are several research programs underway worldwide which seek to lower the carbon intensity of ironmaking; one of the largest is the European ULCOS program [2], in which the main proposed change to blast furnace ironmaking is to scrub CO2 from the furnace off-gas (for possible sequestration), recycling the remaining gas to the furnace. To limit the recycling nitrogen load, oxygen rather than air is used to combust coke.A conceptually simpler approach is to charge prereduced feed (direct-reduced iron) to the blast furnace. This approach has been used for some two decades at the AK Steel Middletown plant, where some 200 kg of direct-reduced iron (DRI) is charged per tonne of hot metal [3]. The Middletown blast furnace has exceptionally high productivity (rate of iron production relative to the furnace hearth area), simply because less coke is required per ton of hot metal if part of the feed is already metallic. Midrex [4] has provided some quantitative predictions of the implications of DRI use in the blast furnace, stating that for every 10% of Fe in the feedstock that is in metallic form, the fuel requirement decreases by 7% and the productivity increases by 8%."

Jan 1, 2012

By Abhishek Lahiri, Animesh Jha

"A new technique for the selective separation of rare earths and impurities from lower grade titaniferous ores has been developed which will reduce the overall reduction in the energy costs, and therefore the CO2 generation by at least an order of magnitude during the chlorination and waste handling stages of TiO2 to TiCl4 reaction. The process includes roasting the ilmenite ore with alkali followed by water washing step, which removes nearly 80% of oxides of lanthanide and actinide elements present in lower grades of titaniferous minerals. In the context of preferential separation of rare- 3+ + earth and actinide oxides, we have examined the roles of Al and K ions on the lattice structures of ilmenite and complex titanate as the product layer forms during the roasting in air in the presence of potash. The composition of the mixtures of oxides derived from the separation process shows that the mixture of rare-earth oxides m ay be a high-value co-product of the overall beneficiation process.IntroductionWorldwide the production of synthetic rutile is carried out either by the sulphate or the slag-making followed by fluidised bed chlorination of TiO2 enriched slag granules. The chlorinated gas is then re-oxidized to make white pigment grade TiO2. The waste generated by the sulphate process is predominantly iron sulphate, which has limited use in the water treatment plant. The remaining wastes from the sulphate process undergo further treatment using filtration followed by evaporation and thermal decomposition after which it is disposed into deep sea. On the other hand the chloride waste is extremely hazardous and requires special case by neutralisation, followed by impoundment in a managed pond, where it is monitored for long-term for potential contamination to the soil and ground water. Rare-earth and prelanthanide wastes often end up in the pond where they are diluted and irretrievably lost for further use or recycle. Certain parts of the world the chloride process wastes are pumped via deep boreholes into porous geological strata. The present techniques of disposal are not only expensive but also pose continued threat groundwater and soil and marine life in case of sulphate waste [1, 2]."

Jan 1, 2009