Search Documents

By Sandeep Upadhya, Marc Morgan, Baljinder Bassi, James Fletcher, Mike Deevy, Nishant Nayan

"In order to protect public safety in the event of a deliberate fire attack, underground rail authorities are increasingly considering the need to design for arson-initiated fire scenarios. Where typical design fires for modern rolling stock mean a peak fire size is reached after 12 minutes, an arson-initiated fire reaches its peak within 2-3 minutes. We present the innovations required to successfully incorporate this requirement on a recent design-build project. In stations 3D modelling is used to optimise smoke reservoir designs, smoke chimneys, station boxes and tunnel geometry to allow coordination with structural requirements. In tunnels, novel coupling of one dimensional network modelling and 3D Computational Fluid Dynamics (CFD) is used to improve assessment of complex fire scenarios. Finally, the impact on tunnel structures is assessed through comparison with standard time-temperature curves and risk of explosive spalling. INTRODUCTION An increasing regulatory environment and the appreciable influence that terrorist incidents have had on public safety policy have motivated the need to protect against large arson fires, especially in civil structures and public transport systems. With a greater reliance of a growing urban population on underground subway systems, design of such infrastructure is continually being reassessed and developed worldwide. Underground rail authorities are paying increased consideration to the design of fires - with properties beyond the upper regions of growth and intensity - amongst arson fire studies. Use of fire hardened materials on modern rolling stock means fires caused accidentally can be expected to develop relative slowly. However, recent experiments involving large initiating fires (as would result from an arson attack) have shown rapid fire growth rates and flashover leading to greater maximum heat release rates, Hadjisophocleous (2012), White (2010), and Lönnermark, et al. (2015). This paper describes the challenges and innovations required to complete a detailed design to control smoke from such aggressive super-fast growing fires. Computational modelling is used to demonstrate the required smoke control design by configuring the mechanical exhaust system combined with careful coordination with the architectural and structural design. The design objectives are to provide tenable egress paths in accordance with NFPA 130 (2014) and fire-fighting access. Finally, analysis of the design fire is used to inform the tunnel lining design, reducing the risk of explosive spalling, protecting the asset in the event of a severe fire."

Jan 1, 2016

By Deborah Muggli

Minera Escondida is the world's largest copper mine. Its capacity is more than 800 kt/a (880,000 stpy) of copper. The Escondida open-pit mine operates at an elevation of 3,100 m (10,170 ft). It is located in the Atacama desert about 160 km (100 miles) southeast of the port of Antofagasta. At Coloso, 14 km (8 miles) south of Antofagasta, copper concentrate is dewatered by filtration for storage and shipment to overseas markets (Fig. 1). Concentrate filtrate water, after being treated to remove suspended solids, is discharged at 60 m (200 ft) depth into the Pacific Ocean. This effluent is free of particulates. However, it does contain metal levels above US Environmental Protection Agency (EPA) receiving water criterion. EPA standards are more strict than Chilean receiving water guidelines. However, a multiport diffuser provides rapid mixing of sea water with effluent to ensure metal levels in the receiving water remain below EPA receiving water guidelines. The Escondida Mine began operation in December 1990 at a rated mill capacity of 35 kt/d (38,500 stpd). Since then, the complex has since undergone three expansions. In 1996, it processed 115 kt/d (127,000 stpd) of ore. At Coloso in 1993, about 25% of the copper concentrate was fed to an ammonia leach plant for solvent extraction and electrowinng of cathode copper. This plant is designed to produce 80 kt/a (88,000 st/year) of cathode copper. In 1995, the ocean diffuser system's capacity was doubled to accommodate increased flows to a maximum 50 L/sec (793 gpm). This was achieved by extending the diffuser chamber by 32 m (105 ft) and adding 16 nozzles, which doubled the diffuser's capacity. In November 1996, Rescan Environmental Services began a field verification of the outfall/diffuser system's performance. The study's objective was to determine the performance of the outfall/diffuser system by measuring dilution factors using fluorescent Rhodamine dye and to determine if copper concentrations are below the US Environmental Protection Agency (EPA) water quality criterion of 2.9 µg/L total copper (EPA, 1986). Rhodamine dye was injected into the outfall/diffuser system. An oceanographic survey using an in situ fluorometer was conducted to measure dye concentrations in the effluent plume. Water column characteristics were also measured. These included current speed and direction.

Jan 1, 1997

By J. P. Mogan

As diesel exhaust contains a mixture of several materials of varying degrees of toxicity which interact to a currently undefined extent in their effects on health, the prescription of a quantity of ventilating air to dilute the exhaust to a safe level is necessarily, to some extent, arbitrary. Some jurisdictions rely on the application of a safety factor to a single "governing" component (usually nitric oxide for most modern diesel engines). Others specify that the total of the "adjusted" concentrations (actual concentration divided by maximum permissible concentration) not exceed "one" for related constituents (irritant gases for example). Neither of these approaches, however, takes account of the interaction of the gaseous constituents with diesel soot (although many studies verify such interactions), nor do they provide any economic incentive for reducing pollutants which are not included in the criteria for ventilation. Because of these factors, the Canadian Department of Energy, Mines and Resources awarded a contract for a study of the current literature bearing on the "Health Implications of Exposure of Underground Mine Workers to Diesel Exhaust Emissions" (1). One goal of this study was the formulation of a new ventilation criterion. The contractors, Ian W. French and Associates, studied more than 1500 literature citations which they interpreted in a 350 page report and summarized in a companion 1600 page annotated bibliography. In the recommendations section of the report, they defined a new 'health effects index' or ventilation criterion "V" as follows: [ ] The contractors consider that a "V" between 3.0 and 4.0 poses a moderate threat to health which could be alleviated by the use of protective equipment such-as filter helmets. If V exceeds 4.0, an increase in ventilation quantity to reduce the pollutant levels is indicated. In the case of mines with a quartz content in excess of 20% in the ore, the contractor recommends that a term. [Quartz]/ [Threshold Limit Value Quartz] be added to the equation, and [2.0 = ?v? = 30] be the range justifying protective equipment, with added ventilation if "v" exceeds 3. A degree of pragmatism was inherent in the development of the equation, as the contractors recognized that the components of the index, if it is to be useful in the near term, should be within current routine underground environmental assay capability.

Jan 1, 1980

By Eric Leung, Stephen G. Hardcastle, Andrew Dasys

In today's economic environment, Canadian mines can ill afford to neglect their ventilation systems as they can consume 30- 40% of the electricity used in underground mines. In addition, Canadian mines can incur significant heating costs. For mines to be their most cost efficient they must embrace existing and emerging technology to optimize the use of their air; namely, maximizing its work in diluting and removing pollutants, limiting leakage, and avoiding the unnecessary consumption of costly fan pressure all the while ensuring the health of their workforce. Furthermore, in Canadian mines which are heavily dieselized there is great interest within the industry to convert from a rigid quantitative approach to ventilation, based upon engine size, towards a more flexible qualitative approach that provides credit for Clean engine technology" and permits ventilation supply to be driven and based upon pollutant demands. In the future, there is even the possibility that ventilation will only be required to supply oxygen to diesel equipment as the underground hands-on workforce is replaced by surface workers and tele-operation. Such changes will allow mine operators to minimize their electrical usage and operating costs, for in its simplest form the cost of running a fan is proportional to the quantity3; therefore, reducing current ventilation demands or limiting increases brought on by more stringent legislation, can produce very significant cost savings. CANMET, through ventilation surveys and use of its modern 3D-CANVENT ventilation simulator, have been demonstrating to the mining industry how ventilation can be optimally delivered at reduced costs. El-Equip with their leaky-feeder communications and MultiVENT monitoring and control system have facilitated mines to control fans and hence costs, and also monitor such ventilation parameters as pollutant concentrations. These two parties are now combining their efforts to develop an integrated air management system which will be demonstrated at CANMET's Experimental Mine Val D'Or, Quebec. With such an air management system, the ventilation engineer will have: 1) a simple to use simulator to design and test ventilation scenarios; 2) remote controls of fans, doors and regulators to implement changes; and 3) real-time monitoring of airflow, pollutant concentrations, and both vehicle identity and location to show whether changes are necessary. It is only when all three are available, that a mine's ventilation system can be operated at minimum cost.

Jan 1, 1997

By B. I. Pålsson, H-Å. Häggblad, J. F. Stener, P. Jonsén

"Understanding mill charge motion is important. In the charge, the center of gravity is shifted from the rotational center of the mill system, and its motion is induced by rotation of the mill. At the same time, the charge creates a torque in the mill system. Breakage of ore particles and wear of liners/ball media are closely linked to this motion. To study these phenomena in a physically correct manner, numerical models for different parts of the mill system are needed. Validations of such models are scarce, because of the difficulty of measuring inside a tumbling mill. Experimental measurements in a lab mill were done for a number of load cases: varying feed material, mill filling, mill speed and pulp liquid. The mill is set up to measure the charge-induced torque. The accuracy is good, with relative uncertainty less than ± 2% for relevant load cases. A full three-dimensional numerical model of the whole mill is used to predict induced torque. Agreement between predicted and measured torque at steady-state is good. In addition, the model can accurately predict the mill startup behavior for torque and mill power. This proves that the model is physically correct, and can be used for modeling large-scale mills.IntroductionUnderstanding of the charge motion within the mill is of importance in mill optimization. The breakage of ore particles and the wear of liners/ball media are closely linked to the charge motion. To study these phenomena in a physically correct manner, appropriate numerical models for different parts of the mill system must be used. Validation of these models is of major importance. This has led to an increased interest in obtaining an accurate and direct measurement of mill load and the behavior of the mill charge.For structural analysis, the finite element method (FEM) is the most developed and most frequently used numerical method. FEM is a numerical solution method based on continuum mechanics modeling. A constitutive relation for the actual material is described, and the governing equations are solved in Zienkiewicz and Taylor (2000). Varieties of different constitutive models for a large number of materials are implemented in modern FEM code. The computability of nonlinear problems in solid mechanics is investigated in Belytschko and Mish (2001), among others."

Jan 1, 2015

By Cary Hirner, Dan Lopez, Ross Webb, Stephen O’Connell

"Construction of the largest desalinization plant in the Americas has commenced in northern Chile. It is part of a several billion dollar expansion at a copper mine whose operations nearly stopped due to the challenge of securing a reliable source of water from the Pacific Ocean in a safe and environmentally sound manner. This paper discusses the risk management, design and construction of a quadruple chamber intake and outfall shaft, high capacity pump station, three 7m diameter vertically drilled marine shafts and three subsea tunnels constructed through challenging Andean hard-rock geology. The three 2.5m diameter subsea microtunnels are being mined with vertical curves through variable quality rock 30 meters beneath the ocean and retrieved in the wet from the 7m diameter marine shafts. INTRODUCTION AND BACKGROUND The battle for securing the rights to a constant water supply is a worldwide issue and nowhere is that more evident than the Atacama Desert of Chile, the world’s driest place with areas of the desert that have not seen rainfall in recorded history. The Atacama Desert also happens to be home to some of the world’s largest ore deposits which require huge amounts of water to extract and process. What available water there is comes from three main sources: deep seated wells, glacial water from the Andes Mountains, and desalinated water. Vying for water from wells and glacial streams and lakes are numerous agricultural and domestic facilities in the valleys surrounding the Atacama Desert. Environmental regulations and legal rulings have limited the amount of “natural” source water which can be used for mining purposes. Desalination plants are a known solution for combating water scarcity, albeit a costly one. The total estimated cost of constructing this desalination plant is over $3B USD, which will include a 2500lps capacity and an approximately 118km pipeline from the coast up to the mine located in the Andes. The overall scope of the project includes design, procurement, and construction packages for the 2500lps desalination plant including the seawater reverse osmosis plant, water conveyance to the mine, power transmission, the reservoir and the marine works package which forms the basis of this paper. Key components of the underground construction portion of the Marine Works are:"

Jan 1, 2016

By M. J. dos Santos

"INTRODUCTION In his landmark Society for Mining, Metallurgy and Exploration (SME) 2000 writing, “Theory and Design of Sandwich Belt High Angle Conveyors According to The Expanded Conveyor Technology” J.A. Dos Santos generalized the belt conveyor technology to include all possible variations and augmentations including, particularly, multiple belts along a common carrying and/or return path as is the case most notably in the sandwich belt high angle conveyor technology and belt-on-belt type intermediate (booster) drives. Figure 1, excerpted from his writing, represented the proposition of the generalized “Expanded Conveyor Technology,” abbreviated ExConTec.This formed the basis for the generalization which was completed in theory and in math before 2000 and presented by J. A. Dos Santos at the Y2K SME Annual Meeting. The writing can be found in the SME library (Dos Santos J. A., January 2000). While Figure 1 with the supporting mathematical development solved the generalization, it failed to identify the variation that would prove to have the greatest significance. As with most significant developments, necessity is the mother of invention. This is the case with the Adder Snake belt technology, the subject of this writing. BACKGROUND The concept of elevating bulk materials at a high angle using the sandwich belt concept was first introduced in 1951. That introduction did not produce any lasting success. Commercial success was achieved in the 1970s with the Loop Belt, a sandwich belt elevator of C-shaped profile developed by Stephens Adamson of Canada. The Loop Belt was and is the vital element of a conveyor based self-unloading ship system. Such self-unloading ships have had great success achieving unloading rates above 10,000 t/h with Loop Belts of width to 3,048mm (120”). Being strictly of C-profile, Loop Belts could not be adapted to the general high angle conveying path which is predominantly along a straight incline. It was the success of the Loop Belts that inspired the Dos Santos Sandwich Belts of the 1980s. These expanded the Loop Belt capabilities by producing endless elevating profiles that could take the most direct and/or conforming path between the loading and discharge points. Sandwich Belt high angle conveyor systems have seen great success through the years, with more than 200 installations throughout the world."

Jan 1, 2018

By Alexander N. Winchell

"The deposits of the east end of the Mesabi Range cover very large areas, and consist of the same taconite that produces the hematite of the central and western Mesabi. It is not deeply covered with drift, but outcrops boldly in large masses. It is not concentrated locally into enriched bodies separated by leaner areas, but is all a fairly uniform, hard, banded, unaltered chert, carrying about 25 to 30 per cent iron as magnetite.The Mesabi Iron Company, organized by Hayden, Stone & Co., and under the direction of D. C. Jackling, has taken over these deposits and is building a Concentrating plant at the new town of Babbitt, about fourteen miles east of Mesaba, Minn. This plant is to have a capacity of 2,000 to 3,000 tons per day, and is based on the application to this low grade material of the methods which have made the so-called porphyry copper properties so successful.In 1916, an experimental mill was built in Duluth; containing full sized machinery and capable of handling from 100 to 200 tons daily. A considerable tonnage of material was concentrated here during 1916, 1917 and 1918. The work showed that the resulting product could be varied, almost at will, between 60 per cent and 70 per cent iron and .006 per cent to .030 per' cent phosphorus, and that this could be made on a large scale well within the limits of cost set by iron trade conditions. A small special cargo was sent down the lakes, late in 1918, assaying 63.27 per cent iron (natural and dry) and .008 per cent phosphorus; but it is assumed that large scale shipments will normally be of a Bessemer' grade carrying about 63 per cent iron and .020 per cent to .030 per cent phosphorus. This material is a sinter, carrying only traces of sulphur and titanium, with silica between 6 per cent and 10 , per cent, and alumina, lime, magnesia, and manganese, each below 1 per cent. Some of the iron in this sinter is hematite and some is magnetite, the percentages varying according to the treatment given on the sintering machine. Like the analyses, this hematite percentage is within reasonable control. Sinter made from finely ground magnetite has much the structure of coke, being firm yet porous, and gives good account of itself in the blast furnace."

Jan 1, 1920

By David Yankovich, Geoff Hughes, David Haug, Jon Kaneshiro

"In March 2013, the Sanitation Districts of Los Angeles County began final design of the Joint Water Pollution Control Plant (JWPCP) Effluent Outfall Tunnel project. The new, approximately 7-mile, 18-ft internal diameter tunnel will provide additional capacity and redundancy for the existing 8- and 12-foot diameter tunnels, which were built in 1937 and 1958, respectively. Connections to an existing, active 14-foot arch force main and four existing ocean outfalls ranging from 5- to 10-foot diameter are required. This paper will present geological features for the project, and details of the proposed post-tensioned tunnel liner and associated structures. INTRODUCTION The Sanitation Districts of Los Angeles County (Sanitation Districts) are 23 independent special districts serving approximately 5.3 million residents in Los Angeles County. Seventeen of the districts that furnish sewerage services to the metropolitan Los Angeles area are signatory to a Joint Outfall Agreement that provides for a regional, interconnected system of facilities known as the Joint Outfall System (JOS). The JOS service area is shown in Figure 1. The JOS serves an area that encompasses 73 cities as well as unincorporated territory and parts of the City of Los Angeles. The JOS provides wastewater collection, treatment, reuse, and disposal for residential, commercial, and industrial users, and it includes seven treatment plants, the largest of which is the JWPCP, located in the City of Carson. Currently, secondary treated effluent is conveyed through two 6-mile long parallel tunnels, 8- and 12-feet in diameter, from the JWPCP to a manifold structure located at Royal Palms Beach, near White Point on the Palos Verdes (PV) Peninsula, from which four seafloor outfalls extend offshore. The two main outfalls, 90- and 120-inches in diameter, extend approximately 1.5 miles offshore and discharge at a depth of approximately 200 feet below sea level. The other two outfalls, 60- and 72-inches in diameter, are used for additional capacity during heavy rain events and extend a shorter distance offshore and discharge at shallower depths. A schematic of the existing system with the proposed tunnel and structures is shown in Figure 2, and the proposed 18-ft diameter tunnel alignment is shown in Figure 3. Both existing tunnels and main outfalls are required to be in service at all times."

Jan 1, 2016

By J. Raatikainen, I. Auranen

"INTRODUCTION Sorting technology has advanced rapidly recently. Of the two possibilities particle sorting has advanced especially in introducing new sensors and the use of multiple sensors. The analyzing and computing lead times have also shortened. This has made it a viable technology option for many applications but not for the most important sorting task at a mine; the run-of mine ore. Bulk sorting, however, has advanced in smaller steps, even if the technology has the capability to tackle the run-of-mine ore and offers a high potential to bring mines substantial economic benefits. The sensors, which are useful are restricted by the difficult operating conditions or by the ore characteristics. One of the important features of run-of-mine sorting technology is the major material handling infrastructure required. The capital expenditure can be substantial requiring good understanding of the sortability curve (grade-recovery curve) behavior of the ore. This paper discusses one industrial case, where substantial amount of data measured from the ore feed belt has been obtained. This data was then analyzed for the grade recovery curves obtainable from that ore with sorting. EXPERIMENTAL The XRF measurement used was the FCA device from IMA Engineering (Fig.1). It is a specially built version of XRF designed to operate with coarse material. The measurement was situated at the main belt conveyor taking ore from the primary crusher to the stockpile. The crushed ore was about 80% -300 mm at a capacity of 1100-1200 tph (Fig.2). Measurement times were varied from 30 seconds to a minute. Measurements were obtained over several months.As the XRF is a surface distribution measuring technique, the measurement was first tested upon accuracy and reproducibility against plant daily wet chemical assays and against on-line Courier feed analysis. As there is a varying delay in the ore stockpile, the delay time was used as a variant in the validation. Different measurement times were tested for accuracy. A one minute measurement time gave a total measurement relative standard error, which was both for Cu and Ni below 3%. The results showed also very robust correlations; for Cu, the correlation coefficient was R > 0,94 for one minute measurements over three months and R > 0,86 for Ni respectively. Fig 3. Shows a measurement period of two hours showing substantial feed grade variations (given as relative value; 1.0 represents the mean value during the measurement month)."

Jan 1, 2018

By Peter P. Harvey

The Nonel Primadet is a non-electric blasting initiation device. The system incorporates the safety advantages of a cap and fuse system with the precision blasting afforded by electrical blasting caps. Each unit is made up of a delay blasting cap factory-crimped to a Nonel® shock tube lead line. The delay elements in the blasting caps are manufactured in both millisecond and long period series. There are 16 periods available in both series - period 0 through period 15. The units are manufactured in 12', 16', and 20' lead lengths. The hollow shock tube is made of surlyn plastic and it is coated on the inside with a reactive material. The powder train has a density of only 1/10 grain per linear foot of tube. A typical blast round is timed precisely the same way it would be with electrical caps. After the round has been timed and loaded, the tube leads are gathered in convenient bunches and tied into a detonating cord trunkline. The Nonel® tube bunches are initiated by the output of an 18 grain per foot detonating cord trunkline. Once initiated, the Nonel® shock tube will reliably propagate at 1800 meters per second. The energy from this shock front initiates the delay elements in each delay cap. The shock tube is inert to electrical energies, including; stray current from AC/DC power sources, as well as, electrostatic discharges. The tube is also inert to initiation by impact. The system has proven to be particularly advantageous in both tunnel and shaft blasting applications. The major advantages in using the Nonel® system in this type of work are: 1) faster and easier tie-in techniques through the use of bunch-blasting. 2) electrical power can be left on during loading and tying-in. a. electrical lights can be turned on at the working face - better lighting facilitates loading and tying-in. b. electrical pumps can continue to function throughout loading and priming procedures (this is particularly advantageous in shaft work with water problems). 3) down-time due to approaching electrical storms is minimized. 4) increased overall efficiency in the blasting cycle: a. it is easier to train a man in the proper use of the system. b. fewer missed holes per round. c. less time required for tie-in. 5) safety-advantage--The system is not susceptible to involuntary initiation from extraneous electrical energies.

Jan 1, 1979

By Liyan Ren, Huayang Dai, Yingcheng Li, Enquan Wang

"Three-dimensional geological modelling of coal mines is critical to the sustainable development of the mining industry. On the basis of comprehensively analyzing 3D geological modelling methods, according to the available data of mine such as geological terrain maps, cross-sections and boreholes, we present a 3D modelling method by integrating ArcGIS and 3D GeoModeller. Our motivation is to integrate the advantages of both software modules in processing, converting, integrating and transferring geological information. Special attention has been given to the data structure and processing flow. We build a 3D geological model of the Xieqiao coal mine and successfully extract the geological framework of the strata in the 11118 workface, which is consistent with that of the actual explored geology.Introduction/Background Pertinent impediments such as a lower information degree, the out-of-date information infrastructure and the low level of information management and decision-making make it critical for there to be improvements in mines. Modern exploration technologies favour the construction of digital mine. Digital mine promotes the transformation of the mining industry by integrating information, automation and intelligence to build safe, efficient, high-yield, green and sustainable mines. Three-dimensional geological modelling and visualization of mines are at the core of digital mine. Compared with traditional 2D geological data, 3D models express the various geological phenomena completely, as well as reproduce the spatial distribution of geological units quickly, allowing for the prediction of mining subsidence, better decision-making and improved geological analysis. Modelling methods such as multi-DEM, tetrahedral grid and the generalized tri-prism that are based on borehole estimation and interpolation data are used to construct 3D models of mine geology (Chen 1995,Wang et al 2003, Wu 2004a); nevertheless, these methods cannot fully use multi-source mining data, whereas multi-source integration methods can be used to build 3D models (Kaufmann and Martin 2008, Zhao et al 2009) but require user interaction in model construction and low automation in model updates. During coal production, a plethora of geological data is accumulated. The organisation of discreteinformation under dynamic conditions and the extraction of meaningful information to better service for three-dimensional modelling is a meaningful work (Wu et al 2004b)."

Jan 1, 2017

By R. L. Grayson, G. Mishra

Introduction Many old underground mines have been developed extensively into reserves requiring large numbers of workers to maintain and rehabilitate lengthy track haulages and/or belt conveyor systems. Often, large numbers of fans are required to maintain minimal airflows in areas where poor conditions and huge leakages prevail. Problems that beset one such coal mine and projects undertaken to restore it to potential profitability are presented. Brief history The Vesta No. 5 mine was opened in 1908. Drift development began near the Monongahela River, which was the primary avenue for shipping metallurgical coal to coke ovens in Pittsburgh. Over the ensuing 75 years, the main haulage entries were developed a distance of 16.1 km (10 miles) to the present mining area. Track haulage was used to transport coal from working sections to the river loading facility. As haulage distance and areas of high water influx increased, management decided, in 1973, to construct an underground conveyor belt system. The project spanned 36 months and culminated in a system of 22 flights, ranging from 205.7 to 1767.8 m (675 to 5800 ft) long. Six intake and eight return entries were developed as the mains were advanced. These entries provided adequate ventilating capacity over the years, but as extensive gob areas progressed and roof conditions deteriorated, the entries became inaccessible and more resistant to airflow. By 1981, five fans were being used to circulate 943.9 m3/s (555.5 cfm) of air through the mine. An average of 6440 t (7100 st) were produced from 20.8 continuous miner unit shifts and 2.7 longwall unit shifts each day in 1981. The ratio of support to production personnel was 1.94. To maintain the outby 16.1 km (10 miles) of haulage, 110 personnel were used. The average cost per ton was $43.54 ($39.58 per st), resulting in excessive bottom-line losses. The mine possessed a rather promising reserve, mostly in lease, of good quality, medium-sulfur metallurgical coal, but it also had a number of formidable operating problems. Operating problems Contributing factors toward relatively low productivity and high costs were the conditions of the track haulage, conveyor, and ventilation systems. Productivity was affected greatly by downtime associated with the conveyor system, which lacked adequate access for making splices or other repairs. Many areas within the conveyor belt entry itself required more

Jan 1, 1988

By John A. Lombardi

The solutions used in the heap biooxidative treatment of sulfidic refractory Au ores and concentrates generally load free mineral acid and metals and, in time, become bacteria activity inhibiting due to increased acid and/or metals concentrations. The metals­acid loaded, bacteria action inhibiting, solution must then be: (a) processed, prior to re-use, to reduce its metals and/or free acid mineral acid components to bacteria activity compatible levels; or (b) neutralized prior to discharge. The most common solution processing method to adjust acid-metals contents is liming to effect the precipitation of dissolved metals and neutralization of acid sufficient for solution discharge or re-use. The lime treated solution is high in suspended, colloidal precipitates and requires clarification before reuse. Most often the "bleedstream" of biooxidation solution that is lime treated is discharged and req­uisite volumes of fresh water added to the process inventory. Depending on the level of bacterial action in a heap and the acid consumption characteristics of the ore/concentrate being biooxi­dized, the bleedstream taken from the circulating, irrigation on­off, solution, can be large (e.g., 10%-20% and sometimes as much as 50% of the daily solution flow requires treatment-dis­charge). The lime charge for bleedstream treatment is commen­surately large and represents a major operating cost of the bioox­idation process. The patented HW Process Technologies (HWPT) Engineered Membrane Separation (EMS™) method is an alternative biooxi­dation bleedstream treatment method. EMS™ processing removes the multivalent base metals ions in an acid solution to a small volume EMS™ "concentrate" (typically 25% of the feed­stream volume). The EMS™ method coincidentally makes a "clean acid" EMS™ "permeate" (typically 75% of the feed­stream volume). In general, EMSTM processing enables 75% of the bleedstream volume to be recycled; allows up to 2/3 of the bleedstream acid to be recovered as a 10% solution; and delivers dissolved metals in a highly concentrated stream suited to a. metals recovery or b. reduced cost lime neutralization for a given metals precip­itation relative to full bleedstream neutralization (typically a 30% lime use savings). Implicit in the recovery of process water for re-use and reduced reagent addition requirement for metals precipitation is a significant reduction in wastewater-sludge dis­posal facility size.

Jan 1, 1998

By Doug Williams, Kent J. McGrew, Dr. Jack Murphy

For some time, selenate has eluded water treatment by conven­tional means such as precipitation and clarification. This has been due to the nearly universal solubility of all oxidized sele­nium species, the low levels required for surface discharge, and almost identical chemical behavior to all forms of oxidized sul­fur. The last characteristic makes selenate particularly difficult to deal with in acid mine waters where sulfate can easily be on the order of one gram per liter. Approaches such as ion exchange or reverse osmosis often tum into total demineraliza­tion schemes for the sake of removing a "trace" selenium species that may be present on the order of 108 sulfate/selenate. Reduction of selenate to selenite or elemental selenium by chemical means has been relatively unresearched. Some limit­ed success has been reported (Murphy, 1988) using ferrous hydroxide as a reducing agent; however, the reaction time as reported is too slow to be useful in a practical plant design. One significant difference between selenate and sulfate is that selenate has been discovered to be reducible in acid solution by elemental iron when catalyzed by soluble copper. Since the +4 or zero valence states of selenium are rather easy to deal with by coprecipitation with iron salts or alum, the elemental iron dis­solved in the process contributes to the overall process by pro­viding sludge upon raising the pH that can be separated by con­ventional clarification. Commercial production of selenium using copper catalyzed reduction of selenite to selenium metal via sulfur dioxide is well established, however, at the < 5 ppb requirements for surface discharge this reduction process equili­brates at levels far too high to be useful to low level selenate removal criteria. The reaction reported herein uses elemental iron for reduction of selenate with copper acting either as a cata­lyst or as a coprecipitation agent. This method, employed with conventional sludging, clarification and filtration can provide an economic method to achieve non detectable selenium (< 0.005 mg/I). Iron consumptions for the conditions tested have been on the order of 3 lbs/1,000 gallons treated. This represents as little as $0.06 or $2.00 per 1,000 gallons based on using a scrap source of iron or the purchase of electrolytic iron for the process.

Jan 1, 1996

By Alfred Petrick, Roger Dewey

INTRODUCTION Estimation of capital and operating costs for mines and mills has long been a necessary ingredient of feasibility studies, and though many practitioners have successfully used "rules of thumb" and factor estimating methods for many years, a great deal of work is usually required to prepare an initial estimate and/or to update or revise such an estimate. Development of comprehensive mining and milling cost models during the 1970&apos;s by the U.S. Bureau of Mines and by Canadian workers (O&apos;Hara and Mullar) provided the basis for feasibility-level cost estimates, but the numerous equations and the apparent rigor and complexity involved in preparing a project estimate using these models has discouraged many, if not most, potential users. Their acceptance was also hindered by a broad misunderstanding by many engineers in the minerals industries who had little exposure to such procedures, and by a possibly inadequate level of explanation or documentation of the parametric approach to cost estimating. The preliminary nature of most databases, geologic/engineering/ and market, available to the engineer or analyst during the early stages of a mineral project is a universal problem. Basing corporate mega-investment decisions or even individual equipment selection decisions on the usual "SWAG’s has always been a risky practice, but in the current business environment, the "guesstimates" are almost &apos;verboten&apos;, and are certainly becoming antiquated with the advent of both the described models, the ubiquitous microcomputer, and the nearly-ubiquitous hybrid species known as the "computerized engineer". Engineers have almost always sought techniques of cost estimation that can be applied and justified when geologic and engineering information for a mining project is preliminary and incomplete. The answer, in some cases, is the "parametric" approach. Equations, based on actual, past experience are developed to relate capital and operating costs to major physical variables such as the rate of mining or milling, with modifiers for such details as mining method, process characteristics, methods of construction, or types of equipment . Cost Engineering Standards Five major types of fixed capital cost estimates have been defined by the American Association of Cost Engineers : 1. Order-of-Magnitude estimate based on previous cost data and minimal knowledge. usually a "ratio estimate" with no better than +/- 30% accuracy. 2. Factored or ratio estimate based on major equipment costs with probable accuracy in the 25 to 30% range. 3. Budget authorization or Preliminary estimate, based on sufficient project data to

Jan 1, 1987

By Michael Drozd

Introduction Flotation is a recovery process that utilizes natural or chemically-introduced hydrophobicity of minerals to separate ore from gangue by attaching the ore particles to bubbles. Flotation has been known since 1906, when it was patented by E. L. Sulman, H. G. K. Pickard and John Ballot. Flotation&apos;s first documented plant use was in 1911, when it was used on gravity tailings from a zinc plant. Cyanide leaching was first patented in 1887. Most early precious metals flotation was linked to lead or copper concentrates. Most precious metal flotation is linked to sulfide recovery and utilizes such reagents as xanthates, dithiophosphates and thiocarbanilides. But the involvement of flotation in precious metals recovery does not have to be limited to active flotation of the gold and silver bearing minerals. Flotation can be used to remove interfering minerals, such as carbon, or cyanicides, such as copper, arsenic bearing minerals or other cyanide complexing minerals. Cyanide Leaching The use of cyanide to recover precious metals is the backbone of the industry. The various recovery processes that use cyanide are: 1. Leaching-Counter Current Decantation(CCD) Merrill-Crowe 2. Carbon-in-pulp (CIP) 3. Carbon-in-leach (CIL) 4. Vat leaching 5. Heap leaching These processes are selected depending on ore grade, ore leaching characteristics, reserve size and capital limitations. Ore grade is used as the first criteria to determine the type of cyanide plant required. However, the reserve size can determine whether a ground ore alternative is used. The ore leaching characteristics may indicate that the higher recovery, associated with a process that employs grinding, is the only economic recovery alternative. There are some extremely large leaching plants with grades that would be non-economic for some existing heap leach plants. Many factors, such as strip ratios, metal recovery and reserve size, determine what the ultimate plant design will be. The exact processing scheme that is used, is a multifaceted decision matrix, which gives the process metallurgist some job security. Precious Metal Recovery Using Flotation Flotation recovery can conceivably be used on any ore that has been ground. Many operations utilize gravity separation on the ore to remove native gold from the ore prior to sending it to cyanide leaching. On certain ores, where the gold is in visible nuggets or particles, this processing alternative is advantageous because the native gold cyanide recovery is

Jan 1, 1993

By Joyce A. Ober

Minerals for electronic and optical uses divide easily into two sections: 1) quartz and 2) minerals other than quartz. QUARTZ The properties of quartz crystal that make it useful for radio communications were discovered in 1918. Since that time, an in¬dustry for the mining and processing of natural quartz crystal has grown, matured, and been almost entirely replaced by new tech¬nology. The new technology still involves quartz crystal, but ma¬terial that is grown rather than mined. An economic summary of the commercial growing of quartz crystals has a place in a handbook directed to the mineral engi¬neering industry because quartz crystals have long been an impor¬tant commercial mineral, and the raw material for cultured quartz - ¬that is to say, quartz crystals grown through the ingenuity of man - is still natural quartz. Nearly all the natural crystals that have been used for elec¬tronics and optics came from Brazil. The larger pieces which met rigorous standards of quality were used for electronic and, to a lesser extent, optical components. Smaller pieces and fragments were used for vitreous silica. The need for high quality material in quantity led to US government sponsored research and exploration programs in the 1940s. No deposits meeting the very rigid requirements for electronic-grade quartz were found, but other projects resulted in the development of a process for the factory growth of beautiful crystals of prescribed shape, size, and quality. Domestic deposits of appropriate quality were identified to use as raw materials for the quartz culturing process. The development of the cultured quartz crystal illustrates the success that technology can have in adapting a product of the mine to increasingly sophisticated uses. A remarkable achievement per¬haps, but foreshadowed by experiments by Giorgio Spezia (1908), an Italian geologist studying the relative effects of temperature and alkaline environment on the solubility of quartz. Modem radio equipment is most often controlled as to fre¬quency by the presence in the circuit of a separately added crystal¬ - the 1918 discovery responsible for the existence and growth of the quartz industry. The crystal is quartz, but this component is a carefully oriented and prepared slice from a crystal, but not a crystal as recognized by a rock hound or seen in a museum. How quartz operates to control frequencies is not a proper subject for a handbook on industrial minerals, and references should be consulted (Cady, 1964, Mason, 1964). Quartz belongs to a class of materials called dielectrics: those that do not conduct an electric current but permit electric fields to exist and act across them. Quartz shows the piezoelectric effect, which means that when a quartz plate is mechanically deformed against its natural stiffness, one of its surfaces becomes negatively charged, the other positively charged. When the plate is released quickly from the stress, the charges disappear as the plate regains its original shape, but because of mechanical momentum the plate deforms in the opposite direction (to a lesser amount) and the surfaces correspondingly become charged in the opposite direction. By thinly coating the two surfaces with metal and attaching flexible wires, these charges can be brought into an electronic circuit. If the surfaces are suddenly electrically charged by movement of current through the wires, the converse piezoelectric effect occurs and the plate deforms. Carry the thought further and it is realized that an alternating current flowing through the wires responds to the mechanical oscillation. By controlling the thickness of the plate, its mechanical vibration frequency can be varied through a wide range. One type of quartz plate, the AT-cut, has a precisely defined orientation with respect to the crystallographic axes of the crystal and vibrates on a microscopic scale much as a book would deform when placed flat on a table and the top cover moved parallel back and forth with the hand. At least 17 other orientations have been studied, some of which have preferred uses in various applications (Cady, 1964). The quartz crystal industry is composed of three main segments (excluding fused quartz and quartz used for optical purposes): 1. Natural electronic-grade quartz crystals. Mined quartz suitable for fabrication into piezoelectric units. Zlobik (1981a) esti¬mated the waste to ore ratio at 1:1000 to 1000 000, depending upon the deposit. 2. Lasca. Mined quartz usable as feedstock in the production of cultured quartz. Approximately 0.63 kg of lasca are required to produce 0.45 kg of cultured quartz. 3. Cultured quartz. Cultured quartz is produced from lasca feed¬stock in a process of crystal growth in an autoclave under conditions of heat, pressure, and time. It is estimated that 0.45 kg of cultured quartz is equivalent to 1.4 to 4.5 kg of natural quartz crystal in yield of commercial quartz suitable for slicing into piezoelectric units. The chronology of the development of the quartz crystal industry both natural and cultured follows: Date Comment 1918 Discovery of the piezoelectric effects of quartz crystal 1921 Application of the piezoelectric effects of quartz crystal in the circuitry of radios 1948 Establishment of a quartz crystal commodity stockpile by the US Government 1952 US consumption of natural quartz crystal at an all time high of 228 t 1958 First commercial production of cultured quartz crystal 1970 Cultured quartz crystal production exceeds imports of nat¬ural quartz crystal 1971 Cultured quartz crystal consumption surpasses natural quartz crystal consumption

Jan 1, 1994

By Robert B. Fulton, Gill Montgomery

Fluorspar is the commercial name for fluorite, a mineral that is calcium fluoride, CaF2. The name, derived from the Latin word fluere (to flow), refers to its low melting point and its early use in metallurgy as a flux. It is the principal industrial source of the element fluorine. Two other minerals, cryolite and fluorapatite, have significant fluorine content. Cryolite, sodium aluminum fluoride, Na3AlF,, is a rare mineral that has been found in commercial quantities only in Greenland. The natural material has been supplanted by synthetic cryolite for its principal industrial use in the manufacture of aluminum. Fluorapatite, Ca5F(PO3)2, is a source of phosphate for fertilizer manufacture, containing a small percentage of fluorine. Commercially mined deposits of apatite have varying amounts of fluorine, chlorine, hydroxyl, and carbonate. HISTORY Fluorspar was used by the early Greeks and Romans for ornamental purposes as vases, drinking cups, and table tops. Various peoples, including the Chinese and the American Indians, carved ornaments and figurines from large crystals. Its usefulness as a flux was known to Agricola in 16th century Europe. Fluorspar mining began in England about 1775 and at various places in the United States between 1820 and 1840. Production grew substantially following the development of basic open hearth steelmaking, wherein it is used as a flux. Use was stimulated by growth of the steel, aluminum, chemical, and ceramic industries, particularly during World Wars I and 11. Fluorocarbons entered the picture in 1931. The use of anhydrous hydrogen fluoride (HF) as a catalyst in the manufacture of alkylate for high octane fuel began in 1942. Differential flotation for separating fluorspar from galena, sphalerite, and common gangue minerals in the 1930s and the application of heavy media concentrating methods to the treatment of low grade ores in the 1940s were outstanding technological advances that facilitated increased production. Pelletizing and briquetting of flotation concentrates for use in steel furnaces and the development of flotation schemes for beneficiating ores containing abundant dolomite and barite have been major improvements in the industry. USES OF FLUORITE Fluorspar is used to make hydrogen fluoride (HF), also called hydrofluoric acid, an intermediate for fluorocarbons, aluminum fluoride, and synthetic cryolite. It is used as a flux in the steel and ceramic industries, in iron foundry and ferroalloy practice, and has many minor specialized uses. Hydrogen fluoride is produced by reacting acid grade (97% CaF,) fluorspar with sulfuric acid in a heated kiln or retort to produce HF gas and calcium sulfate. After purification by scrubbing, condensing, and distillation; the HF is marketed as anhydrous HF, a colorless fuming liquid, or it may be absorbed in water to form the aqueous acid, usually 70% HF. Synthetic cryolite, organic and inorganic fluoride chemicals, and elemental fluorine are made from hydrofluoric acid. The acid itself is important in catalysis in the manufacture of alkylate, an ingredient in high-octane fuel for aircraft and automobiles; in steel pickling, enamel stripping, and glass etching and polishing; and in various electroplating operations. The manufacture of one ton of virgin aluminum requires about 12 to 29 kg of fluorine content in synthetic cryolite and aluminum fluoride. This quantity, through improved technology and recovery practices, is being lowered significantly in countries with the most advanced technology (i.e., Australia and Sweden), while others (i.e., Surinam and South Africa), remain at the high end. Elemental fluorine is prepared from anhydrous hydrofluoric acid by electrolysis. Gaseous at room temperature and pressure, fluorine is compressed to a liquid for shipment in cylinders or in tank trucks. Elemental fluorine is used to make uranium hexafluoride, sulfur hexafluoride, and halogen fluorides. Gaseous uranium hexafluoride is used in separating U235 from U233 by the diffusion process. Sulfur hexafluoride is a stable high dielectric gas used in coaxial cables, transformers, and radar wave guides. Halogen fluorides have important applications, mostly as substitutes for elemental fluorine, which is more difficult to handle. Emulsified perfluorochemicals, organic compounds in which all hydrogen atoms have been replaced by fluorine, are undergoing investigation as promising blood substitutes. They transport oxygen and, in conjunction with a simulated blood serum, perform many functions of whole blood. With further development, these organic compounds may ultimately, in emergencies, be useful in saving lives of animals and humans during periods of acute shortages of natural blood. Inorganic fluorides are used as insecticides, preservatives, antiseptics, ceramic additives, and fluxes and in electroplating solutions, antioxidants, and many other products. Boron trifluoride is an important catalyst. Organic fluorides are volume leaders in the fluorine chemical industry. Fluorinated chlorocarbons and fluorocarbons are prepared by the interaction of anhydrous HF with chloroform, perchlorethylene and carbon tetrachloride, and are characterized by low toxicity and notable chemical stability. They perform outstandingly as refrigerants, aerosol propellants, solvents, and cleaning agents and as intermediates for polymers such as fluorocarbon resins and elastomers. Fluorocarbon resins are inert compounds that have unusually low coefficients of friction and have found a number of applications as lubricants for parts that cannot be oiled, e.g., bearings for window raising equipment located inside of automobile doors, in small electronic equipment, for the manufacture of chem-

Jan 1, 1994

By V. A. Leach, Lokan. K. H., S. B. Solomon, R. S. O’Brien, L. J. Martin, K. N. Wise

INTRODUCTION The development during 1979 of a relatively small, but high grade (10,000 tonnes uranium at an average grade of 2 per cent), uranium ore body at Nabarlek in the Northern Territory, Australia offered an excellent opportunity to obtain detailed radiation data for an open cut mine operating during the dry season. The ore body (Queensland Mines Limited-1979), which was completely extracted in a period of four and a half months, consisted of a vein type deposit dipping at 30 to 45 degrees and contained a central core of pitchblende in massive and irregular pods, surrounded by lower grade fine grained disseminated pitchblende. Mineralisation extended from the surface to a depth of 72 metres over a length of 230 metres with an average but variable thickness of 1D metres. Ore near the surface had been heavily weathered and complex secondary minerals were formed which had dispersed from the main vein. Mining was carried out with large earth moving equipment. Overburden and weathered surface ore were removed initially with scrapers. At greater depths bulldozers were used to rip and assemble ore and rock at each level, and these were removed by large trucks to the ore and waste rock stockpiles. Where necessary, blasting took place during shift changes each evening. Mining was essentially continuous with two ten hour alternating shifts working for thirteen days out of fourteen. At the completion of mining a relatively small excavation (335m x 185m x 70m) remained, and this will serve as a tailings repository during the milling phase. FIELD MEASUREMENTS The inhalation of radon daughters, arising from the radioactive decay of radon gas is well established (Archer et. al. 1973) as a potential hazard in the uranium mining industry. Control over radon and its daughters to ensure that recommended exposure limits are not exceeded is achieved by providing adequate ventilation, and under normal circumstances natural ventilation from an open pit should be sufficient. However, during the dry season it is not uncommon for stable atmospheric conditions, with little horizontal air movement, to develop - particularly at night - and significant radon daughter concentrations may accumulate. Throughout the entire mining period measurements were therefore made of radon and radon daughter levels at representative locations within the pit and on the ore stockpile as it developed. Initially these measurements were carried out manually, using the Rolle method for radon daughters, (Rolle 1972) and .scintillation cells (Lucas 1964) or a two filter tube for the determination of radon (Thomas 1970). For the latter half of the period however, a continuous recording instrument, developed within the Laboratory was used to provide a detailed record of radon daughter levels within the pit. At the same time, continuous readings of wind speed and direction, and vertical temperature gradient between 10 and 3D metres were recorded on a 30 metre meteorological tower, situated 800 metres from the pit. Radon Emanation Rates It is evident that radon and radon daughter concentrations depend on the grade, or more particularly, on the surface radon emanation rate of the ore which is exposed. Accordingly, as the mine progressed, detailed measurements were made of both of these quantities. The surface emanation rate of radon was determined for each ore bench as it was exposed by placing an extended array of canisters, filled with freshly degassed activated charcoal, face down on the ore for a known time. These canisters, which had previously been calibrated in the Laboratory, adsorb radon with high efficiency, and the total radon adsorbed is measured after retrieval by detecting the gamma rays from the trapped radon daughters (Countess 1977). At the same time, as each canister was placed in position, a measurement of the local ore grade was made for each location. This was achieved with a calibrated sodium iodide scintillation detector, adjusted to detect the 609 keV gamma ray from the isotope 2148i, a decay product of radium. Finally, measurements were made of the radiation field 1 metre above the surface, with a gamma ray survey meter, which was calibrated in the Laboratory. The relationship between the scintillator count rate and ore grade was determined by comparing the scintillator output with the gamma monitor, and relating the latter measurements to ore grade (Thomson and Wilson 1980). It was observed that while emanation rates and ore grades varied widely, the ratio of emanation rate to ore grade was in general fairly stable. A plot of this ratio is presented as a function of depth below the original surface in Figure 1. For most observations the ratio is constant at a value of 80 Bq m-2 s -1 per unit ore grade, where ore grade is expressed as percentage of U308. At the surface however, where the ore was weathered, the ratio was about a factor of three higher, and at two particular depths, where high grade pitchblende was being removed, it was very much lower. This was not unexpected as earlier Laboratory studies of drill core samples from Nabarlek had indicated that the emanation coefficient (the fraction of radon produced within the ore which escapes from the mineral particles) decreases with increasing ore grade.

Jan 1, 1981