Search Documents

By S. B. Hildebrand

One of the highest costs associated with insitu leaching of copper is electric power. The ReGeneration Project addressed this cost issue with a research and development project for BHP Copper. The project involved the installation of a reverse pump/turbine for the removal of excessive fluid pressure and the production of useful electric power. The motivation for the project was that a reverse pump/turbine unit could not only remove the excess hydraulic pressure, but when connected to an induction .generator, would produce electric power, which could be easily connected to the local power gird, thus reducing operating costs. The project was successful in removing excess fluid pressure and producing electricity. The unit is operating today, producing useful 2,300 volt power at a rate of approximately 128 kilowatts.

Jan 1, 1998

By Jaime E. Sepúlveda

Semiautogenous grinding (SAG) operators have been realizing the very significant impact of fresh feed particle size distribution on the mill grinding capacity. In actual practice, this impact may be quite difficult to assess because of the natural process variability that may also involve- concurrently other critical factors such as ore hardness. Recognizing the limitations of the empirical approach, the current publication proposes the use of mathematical models and simulators to explore and assess the net effect of feed particle size only, independent of any other factors. The simulation analysis here reported provides a basis to claim that the size distribution of the particles being ground (simply characterized by a % - 2" or similar measurement) is one of the most relevant controlling variables of the overall mill performance, regardless of the SAG circuit configuration.

Jan 1, 2005

By B. K. Cantrell, K. L. Rubow

The US Bureau of Mines and the University of Minnesota have developed design and performance criteria for a personal diesel exhaust aerosol sampler for underground coal mines. These are based on the premise that size can be used to separate diesel exhaust aerosol, which is mostly submicron in size, from coal dust aerosol, which is mostly greater than a micron in size. The sampler has three stages: a respirable aerosol preclassifier, a 0.8- µm aerodynamic diameter inertial impactor to collect mineral dust and a final filter to collect the diesel aerosol. Using a sample flow rate of 2 L/min and gravimetric analysis to within 0.1 mg, the measure sub-0.8 µm diesel aerosol has an a-priori limit of detection of 0.3 mg/m3.

Jan 1, 1992

By John A. Herbst

At the last Comminution Symposium a challenge (Meloy and Williams, 1992) was issued to "predict the typical straight-line, self similar" tumbling mill product size distributions using a population balance model (PBM). Implicit in this challenge is the assumption that the PBM is inadequate for predicting real world grinding performance. This response is presented in three parts: I. Theoretical analysis of the general PBM and its appropriateness for comminution system modeling. II. Examination of the accuracy of prediction of real world milling behavior using linear and nonlinear PBMs. III. Evidence from recent microscale comminution research. This paper concludes with recommendations concerning future research which will: 1. further elucidate mechanisms of particle destruction and creation as well as attrition and 2. increase the accuracy of model predictions in highly nonlinear situations

Jan 1, 1997

By Hassan El-Shall, Abbas A. Zaman, Brij M. Moudgil

The addition of organic and inorganic dispersants to aqueous suspensions of heterogeneous particles (kaolin) was found to significantly affect the solubility of metal ions from kaolin particles and stability of the dispersion. In most of the industrial applications of kaolin, highly concentrated slurries of controlled stability and fluidity are required. The solubility of kaolin particles in terms of aluminum and silicon ions and its effect on the stability of the slurry was investigated. The main objectives of this study were (1) to study the effect of the extracted metals on the properties and performance of the slurry, (2) to understand the reaction mechanism of dissolution of metals from kaolin, and (3) to understand the interaction mechanism of dispersants with kaolin particles. The controlling variables were dispersant dosage, slurry pH, solids loading, and aging.

Jan 1, 2003

By S. D. F. Rocha

The influence of surfactants on the crystallization of calcium sulfate was investigated in both hatch and continuous systems. The investigation was per formed at the following conditions. 343 °K, 28% P205 and with a sulfate level of 2.0%. At concentrations of 5 and 200 µgig, respectively, dodecylbenzene sulfonic acid (DBSH) and sodium diisooctil sulosuccinate (SSNa) promoted both an increase in the size and a reduction in the length/width (L/W) ratio of the calcium sulfate hydrates produced in the hatch and continuous crystallizers. Unique effects were observed in the batch system at higher DBSH concentrations. At 10 µg/g, the precipitation of hemihydrate crystals with a distinct morphology and texture occurred under conditions where dihydrate precipitation was expected. Above 50 µg/g, the precipitation of calcium sulfate hydrates was completely inhibited.

Jan 1, 1996

By M. S. Klima, A. Simard, M. L. Turek

Laboratory testing was carried out to evaluate several devices for recovering clean coal from bituminous coal refuse material. The bulk of the testing focused on using a dense-medium cyclone to process -0.6-mm refuse material. A hindered-settling column and a spiral concentrator were also used to process nominal 1.2 x 0.15-mm material. Product yields and ash contents were obtained for all tests, while partition curves were generated for selected tests from which the characteristic performance parameters (relative density of separation and probable error) were determined. The results indicated that the dense-medium cyclone was capable of cleaning down to 0.037 mm, while the other devices were effective to 0.15 mm. Keywords: Coal recovery, Coal refuse, Dense-medium cyclone, Hindered settling, Spiral concentration

Jan 1, 2003

By James Warren Andrews

The values of saturated water vapor pressure from steam tables have been found to be inaccurate for mine ventilation usage because the effect of air on the saturated water vapor was disregarded. Presented here are the newest and most accurate currently available tables from the National Bureau of Standards (NBS). Also included are: (1) a formula for correcting the saturated water vapor pressure for temperature and altitude. (2) a formula for computing unsaturated water vapor pressure, and (3) a formula for air density. Because Systeme International (SI) units are used in the formulas, conversions are given from U. S. conventional units to SI units. The intent of this paper is to show by means of six steps the accurate calculation of mine air density for use on modern computers.

Jan 1, 1989

By D. X. Tang, G. Wilson, Y. Luo, S. S. Peng

Knowing the location of voids/fractures in roof rock will be greatly helpful for roof support design. The drilling parameters obtained during normal roof bolt installation cycle provide a fast and economic way for determining void location in roof rock. In this research, feed pressure and rotation torque are found to be good indicators for identifying the voids, based on the results of a series of laboratory experiments. A set of computational rules has been developed to locate voids in mine roof using the measured roof drilling parameters and implemented in MRGIS, a software package developed to allow mine engineers to make use of the large amount of roof drilling parameters for predicting roof geology properties automatically. Anew feature, 2D map+3D figure display, is also added to MRGIS.

Jan 1, 2004

By C. E. Zebula, F. F. Aplan, R. S. Datta

The hydrophobicity of oil shale was found to follow the sequence R-5 > Mahogany >> Eastern. Further, hydrophobicity was found to correlate with the total organic carbon (TOG) content, decreasing with increasing specific gravity of raw oil shale pieces. Differences in hydrophobicity from piece to piece indicate that gravity preconcentration would be much more effective for Western than for Eastern oil shales. Purified kerogen concentrates and low specific gravity fractions (<2.0) of raw Western oil shale samples show critical surface tension of wetting values of [y]c = ~35 mNm -1, and for a kerogen concentrate from an Eastern oil shale [y]c = ~46 mNm-l. This infers that dust from oil shale mining operations can be suppressed by surfactant solutions similar to those used to suppress coal dust.

Jan 1, 1988

By A. E. Prokop, J. P. Rider

Previous research on continuous mining operations has shown that significant interactions exist between dust-control parameter application and the resulting respirable dust levels. However, simply increasing the level of the controls does not guarantee a reduction in respirable dust levels. Full-scale laboratory tests are being conducted to provide information to longwall operators that would assist them in selecting control parameters to reduce dust levels for mine-specific conditions. The interactions between face air velocity, shearer water quantity, drum water spray pressure, external water spray pressure and spray system design were evaluated in a simulated 2.13-m (7 ft) coal seam for two cutting directions. Locations around and downwind of the shearer were monitored to evaluate relative changes in respirable dust levels as a function of each control parameter.

Jan 1, 2003

By Christof Brewka

Los Pelambres, 200 km north of Santiago, Chile, is the latest in a series of mega-projects developed in this part of the world. While most of its predecessors are spread over open desert, the Los Pelambres mine is nestled inside a narrow alpine valley high in the Andean Mountains. To handle the daunting task of transporting the mined copper ore more than 12 km and 1,400 vertical meters downhill to the concentrator plant, a gigantic belt conveyor system (capacity of 8700 mtph, 1800 mm wide ST 7800 steel cord belt, 2.5m diameter pulleys, an elaborate braking system including a mechanical failsafe and large reducers with a total installed drive power of 25,000 kW) has been employed. Many of these components have pushed the limits of conventional belt conveyor design.

Jan 1, 2000

By Feng Dingwu, Chen Jin, Sun Zhongyuan, Peng Shiying

The recent development of rare-earth permanent magnets has impacted the field of magnetic separation. The permanent magnets technology led to the advent of various magnetic separators particularly designed for application in mineral processing. In this paper, a new type of rare-earth PHGMS possessing a higher magnetic field strength in the working zone was developed using finite element analysis techniques. The NdFeB permanent magnets used had properties of 38 MGOe stored energy, and magnetic material flux levels exceed 1.2 T, The combination of scientific and engineering design and suitable matrices can offer an effective separation of industrial minerals, such as kaolin, feldspar, etc. Compared with conventional high intensity electromagnetic separators, the equipment can reduce electrical energy over 80% with lower operation and maintenance costs, and less installation space.

Jan 1, 1995

By L. R. Freitas, A. K. Resende, J. A. Oliveria, K. L. Gonçalves, L. F. D’Assumpção, L. R. Lage, J. D. Neto, F. Viveiros

Pará Pigmentos S.A. (PPSA) is an association between the Brazilian companies CVRD and CADAM, Mitsubishi Corporation of Japan, and the IFC (World Bank) created in 1992 in order to recover kaolin from Rio Capim deposit, northern Brazil. Commercial production at PPSA started in August 1996 using a process comprising mining and beneficiation at the mine site, pumping through a pipeline and drying/loading at the port site on the Amazon river estuary. Presently, all PPSA production is concentrated on 82% <2um, high-brightness coating clay shipped in bulk. In this paper, a detailed description of the development of PPSA beneficiation process is presented. The results of laboratory and pilot plant studies under- taken to develop alternative grades of clay, such as delaminated and calcined kaolins, are also discussed.

Jan 1, 1998

By F. M. Doyle, Jiang Tao, Xu Shi, Chen Jin, E. Peters

Tafel curve technique and leaching tests have been applied to study the kinetics of gold leaching with thiosulfate. Results show that cupric ions and ammonia play the part of catalysts in the leaching of gold with thiosulfate. The activation energy of gold dissolution is calculated as 27.99 KJ/mol in the absence of both cupric ions and ammonia. However, the energy is reduced to 15.54 KJ/mol in a solution of 0.01 mol/L Cu (NH3)2 4* and 0. 5moVL total ammonia. The reaction order of Cu (NH,) g is one in the range of 0.001~0.1mol/L. These results support the electrochemical-catalytic mechanism pro- posed by the authors and explains the behavior of cupric ion and ammonia (Jiang Tao, et al., 1993)

Jan 1, 1993

By Wang Dianzuo, Luo Lin, Hu Yuehua, Qiu Guanzhou

This paper introduces a novel classification approach named the flotation classification approach which works by controlling interactions between particles. It differs considerably from the conventional classification processes operating on mechanical forces. In the present test, the micro-bubble flotation technology is grafted onto hydro-classification. Selective aggregation and dispersion of ultrafine particles are achieved through governing the interactions in the classification process. A series of laboratory classification tests for -44 pm kaolin have been conducted on a classification column. As a result, about 92 percent recovery for minus 2 pm size fraction Kaolin in the final product is obtained. In addition, two criteria for the classification are set up. Finally, a principle of classifying and controlling the interactions between particles is discussed in terms of surface thermodynamics and hydrodynamics.

Jan 1, 1995

By J. A. Herbst, C Lo. Y, Z. Rogovin

The identification and quantification of incipient overload conditions in mills have recently been found to be very significant in the design of tumbling grinding mills. To investigate these phenomena, a series of experiments was conducted in a Plexiglas mill operated in both dry and wet modes. For on-stream measurement of the mill charge weight, volumetric filling, dynamic angle of repose, and mill power, an electronic system was developed. The mill was filled to various levels with 19.1-mm (3/4-in.) ceramic balls as grinding media. As feed material, grindable limestone or 3.2-mm (1/8-in.) nongrinding ceramic balls were fed at various steady-state rates to determine the incipient overload conditions. The prediction of overload has apparently been reduced to predicting the feed rate that results in 50% mill filling.

Jan 1, 1988

By Jr. Gambrell

Support characteristics of in-cycle trusses are analyzed using a photo-elastic model loaded by tightening a truss in the sequence normally used in an underground mine. Stresses in the roof at its center point and at the junction of the roof and rib are examined. Effects of zero tension and unequal tension in the inclined anchor rods are presented. Effects of simulated subsidence on stress in the roof surface and on tension in the separate truss members are examined. Conclusions are drawn relating to (1) the effects of tension in the inclined anchor rods on uplift and compressive stress parallel to the roof surface, (2) the effects of subsidence on stress in the roof surface and, (3) the effects of subsidence on tension in the truss members.

Jan 1, 1989

By Robert Roggenthen

In 1994, ASARCO&apos;s Mission Complex Mine Planning Department designed a new stripping schedule to take advantage of reserve opportunities. Based upon the new stripping design, overburden removal exceeded available hauling capacity. This increased hauling capacity requirement required that ASARCO consider alternative technologies for material transport. In 1997, ASARCO Mission Complex completed the purchase and installation of a 3.5 km, 8,600-tph conveyor system to transport waste material. The conveyor system is composed of two apron feeder/sizer units manufactured by Mining Machine Development LTD. and a conveyor system manufactured by Krupp-Robbins. This paper will review the option of truck haulage versus conveyor transport for overburden removal by (1) describing engineering studies contributing to the solution, (2) researching proactive options to create alternative management decisions, and (3) revealing final results of the project.

Jan 1, 1998

By G. Atesok, M. Hancer, M. S. Celik, O. F. Emrullahoglu

Multivalent ions are shown to activate the flotation of colemanite in the presence of sodium dodecylsulfate (NaDDS). Floatation recoveries versus barium ion concentrations exhibit three distinct regions of floatability. Adsorption, zeta potential and solubility mesurements under comparable conditions reveal that Region I is characterized by the uptake of Me2+ ions followed by electrostatic attraction of sulfate ions onto the oppositely charged surface. The improvement observed in flotation recoveries in Regions II and III is ascribed to surface and bulk precipitation of metal dodecyl sulfate onto colemanite, respectively. While the most soluble BaDDS ions yield the highest activation, the least soluble MgDDS achieve the lowest activation. It is postulated that metal ions depending on their solubility products with DDS are capable of activating the boron minerals.

Jan 1, 1993