Search Documents

By C. M. Chang, H Gu, J. A. Barrera-Godínez, T. J. O’Keefe

The inability to economically separate Fe3+(aq) from a variety of liquid effluents is a major Concern for the primary metals industry. A unique solvent extraction process, galvanic stripping, has been developed to address this problem. The galvanic stripping of iron from D2EHPA using only a 5~10 g/L H2SO4 solution is achieved after Fe3+ is directly reduced to Fee, in the organic phase using zinc metal additions. To date, the primary focus of the laboratory research has been on optimizing the parameters that control iron removal. The results from these studies have now been, used to make a preliminary design for a continuous flow process that is envisioned for zinc industrial applications. Specific quantitative data are shown for the use of a Zn-Ph cellos° in the iron-reams al process. Some introductory results on electrochemical potential measurements and impurity distribution with solution cycling are also giiven.

Jan 1, 2000

By J. Engesser

A research project was undertaken to determine if coal addition tofluxed-magnetite pre-fired pellets would reduce nitrogen oxide (NOx)emissions during pellet induration. Iron oxidation rate tests, coal oxidation rate tests and calcination rate tests were conducted in a laboratory furnace to determine the amount of coal necessary to provide adequate heat for limestone calcination without producing detrimental effects to magnetite oxidation. Pilot scale pot-grate tests were then performed with and without coal in the pre-fired pellets to verify pellet quality parameters and nitrogen oxide emissions. The off-gas during each pot-grate test was analyzed for NOx, CO2, CO, SOx, and O2. There was approximately a ten percent reduction in NOx emissions with coal addition during the normal pot-grate firing cycle. There was a 75% reduction in NOx emissions during firing cycles that used 25% to 75% excess air during firing rather than the normal 300% excess air.

Jan 1, 2003

By V. B. Achanti

Laboratory studies were carried out at West Virginia University to investigate the rock fragmentation mechanism by continuous miners using an automated rotary cutting simulator. The primary factors influencing the: fragmentation process were found to be: bit spacing, bit geometry, depth of cut, and cutting drum rotational speed. This paper presents the influence of these parameters in achieving optimum energy consumption and minimizing dust generation during rock fragmentation process. Three bits were used simultaneously on Indiana limestone while the bit tip angle was varied from 60° to 90°. Bit spacing was varied from 2.54 cm (1 in.) to 5.08 cm (2 in.) while the cutting process was assessed for varying cutting depths. Respirable dust generated during the course of the experiments was analyzed utilizing cascade impactors. Assessment of these parameters has led to a better understanding of the cutting mechanism by continuous miners in terms of energy consumption and dust generation.

Jan 1, 1997

By J. Hanna

The University of Alabama Mineral Resources Institute (MRI) has developed a unique process for selective fatty acid flotation of carbonate gangue from sedimentary apatites (francolite) in the pH range of 4-6 without collector conditioning of the pulp. The process, which does not require an apatite depressant, was modified to benepciate a high- MgO siliceous phosphate matrix from south Florida. The modified process includes two flotation stages, one for car- bonate removal and the other for phosphate recovery from the siliceous gangue. The selective flotation separation of the carbonate and phosphate from siliceous constituents of the matrix at various pH levels and collector dosages are discussed. In the carbonate flotation stage, about 70% of the MgO was rejected in the froth. The phosphate flotation stage produced concentrates analyzing about 31% P2O5 0.7% ? 5 MgO, and 4% insol. The overall P2O5 recovery In the two stages was about 85%

Jan 1, 1991

By Kenneth J. Leib, Laurie Wirt, M. Alisa Mast

Chemical-constituent loads were determined for an alpine stream in southwestern Colorado that is affected by natural acid drainage from weathering of hydrothermally-altered rock and from acidic metal-rich discharge from abandoned mines. Base-flow loads were compared to storm-related loads using a tracer-dilution approach. A rainstom occurred during the tracer injection, providing the opportunity to measure metal loads before, during, and after storm runoff. Chemical-constituent loads during the storm increased by 1 to 2 orders of magnitude relative to base-flow conditions. The increase in loads was related to two distinct periods; (1) a flush of higher concentrations that occurred soon after rainfall began, and (2) the peak of storm runoff. The initial flush-having no measurable change in discharge--contained the highest loads of trace metals and dissolved iron. The chemical character of peak runoff was distinctly different, as evidenced by the highest loads of total and dissolved major elements and total iron.

Jan 1, 2000

By R. Bhaskar, H. Xie

Fractal theory was horn in the mid-1970s. Since then, its application has been spreading day by day, from mathematics and geology to areas such as geophysics, physics and material sciences. In this paper, fractal models are developed to characterize particle size distribution and surface area. Theoretical formulas are derived for the computation of fractal dimensions D (size) and D[s] (surface area). The models developed are applied using experimental data of particle size distribution and surface area obtained from the Microtrac Particle Size Analyzer for dust processed by several size reduction devices. The theoretical models and the experimental data are found in good agreement. The fractal dimensions obtained are D = 1.350 to 1.770 and D[s] = 2.058 to 2.584 for fine coal dust particles (< 15 µm) produced by various size reduction mechanisms. The physical meaning of these fractal dimensions is also related to the dust generation processes.

Jan 1, 1994

By John Matthews

During 1982 and 1983, it became increasingly clear that North River No. 1 Mine would have to buy a set of replacement longwall shields. Despite extensive efforts to make improvements, the shields that were in place at that time were incapable of holding the roof. North River Energy had limited experience in specifying and acquiring longwall roof supports, but a great deal of experience with our conditions and needs. We there- fore compiled a shield evaluation method that uniquely responded to our situation. The resulting system emphasized teamwork among operating, maintenance and engineering personnel. The charge from management was threefold: select shields to support maximum expected loads, optimize face operations, and pay attention to detail. Final selection was made objectively, based on all available information. We chose a 5516 KN (620 tons) support with a minimum yield load density of 760 KN/m2 (7.9 tons/ft2). This paper reviews our process of specification, design, prototype testing, and fabrication, and offers some relevant suggestions.

Jan 1, 1986

By Eric C. Schwamberge, Clem A. Pelletier, Deborah L. Muggli, George W. Poling

The Pit Lake at Island Copper has evolved into a 3-layered meromictic system. Acid Rock Drainage (ARD) is collected and injected into the lake at 220 m depth via 2 diffuser systems. In situ dye studies were conducted during 2 differing hydrological regimes in order to determine the behavior of the ARD plume within the Pit Lake. Results indicated that when runoff from the waste dumps was low, the injected ARD remained within the bottom half of the intermediate layer of the Pit Lake, initially below depths of 90 m. However, when runoff from the waste dumps was high, the injected ARD at -220 m depth rose through the intermediate water column layer rapidly, but did not breach the top pycnocline at -10 m depth. Overall, the system is currently performing as a mixing bowl with a strong boundary or cap at the upper pycnocline. maintaining mixing below the 10 m depth water level.

Jan 1, 2000

By J. G. Henning, R. Edrissi

This paper describes a practical methodology, based on numerical modeling, for the prediction of progressive failure of underground-mine stopes having cable-bolt support. A case study of the 40-761 scope at the Kidd Creek mine, Timmins, Ontario, Canada is presented. Scope 40-761 was mined by blast hole open sloping in 1986 and was a lead scope within a mining block located between levels 36-1 and 38-2. Initially designed to peak at level 38-2, the scope back caved upwards =40 m towards level 36-1. After caving began, cable bolts were installed above the stope from level 36-1. The stope eventually stopped caving when the falling rock mass encountered a sufficiently high cable density. This paper provides details of the geomechanical data and modeling results of the case study. Numerical modeling of cable bolts around the mine stoke was carried out using a finite-element modeling software. The software, known as e-z tools, was developed by the first author.

Jan 1, 1996

In 1993, the United States&apos; economy grew at a rate of about 3%. The Gross Domestic Product rose to $6.4 trillion. With more than 258 million people - 599,000 in mining including petroleum - the United States has more than 100 million dwelling units and more than 190 million licensed motor vehicles. New private housing starts rose 7% to 1.3 million units, new car production fell 3% to 5.5 million units and truck and bus production rose 21 % to 4.9 million units. The rate of inflation was under 3% and the prime rate of interest 6%. The Producer Price Index (1982 = 100) was unchanged from 1992 for fuels and re¬lated products and power at 80 and met¬als and metal products at 119, while chemicals and allied products rose 2% to 128 and non-metallic mineral prod¬ucts rose 2% to 120. The merchandise trade deficit rose 27% to $116 billion.

Jan 1, 1994

By Jae-Chun Lee, Kang-In Rhee, D. B. Dreisinger, Hyo-Shin Yu, G. A. Kordosky

The development of a process for direct synthesis of very pure ZnO powders from zinc-bearing waste was investigated. The zinc waste which contains 55% zinc was leached with sulfuric acid. After iron removal by hydrolysis from this zinc solution, purification through solvent extraction by the use of D2EHPA as an extractant was carried out. Then, loaded zinc in the organic solution was stripped and precipitated simultaneously using oxalic acid as a precipitant. Synthesized ZnC2O4 precursors by precipitation stripping were calcined to obtain ZnO powders exceeding 99.9% purity. The effects of sulfuric acid concentration, leaching time, and pulp density on the extraction of zinc were studied and optimum conditions for the solvent extraction were obtained through purification of the zinc solution. The size, morphology, and size distribution of synthesized ZnC204 powders were studied in terms of oxalic acid concentration, temperature, surfactant added, precipitation time, etc.

Jan 1, 1993

By Michael S. Kucker, Robert A. Robinson, Harvey W. Parker

Ground deformations are of major concern during tunneling, especially in downtown environments, since they have a significant impact on the costs and practicality of tunneling. This case history describes soil and groundwater conditions and ground behavior during the construction of twin transit tunnels for the Downtown Seattle Transit Project (DSTP). The tunnels were excavated through complex glacial soils ranging from hard glaciomarine drift to flowing sand. The tunneling process was greatly facilitated by the prediction of soil layer positions to an accuracy of ±0.6 m (2 ft). Tunneling was complicated by the presence of over 500 temporary tiebacks and by disturbed ground overlying an operating railroad tunnel. A variety of ground improvement techniques were used to successfully minimize settlements, which ranged from 1 cm (0.4 in.) in glaciomarine drift to 6 cm (2.4 in.) in flowing sands. Ground improvement techniques included compaction grouting, chemical grouting, jet grouting, and eductor well systems.

Jan 1, 1991

By Maynard O. Serbousek, Melvin E. Poad

Shotcrete, a useful support material in underground openings, is a sprayed concrete, and, when used with fast-setting agents, is immediately self-supporting. Although shotcrete has been used extensively for tunnel support, the technique has not been readily accepted by the mining industry because of the lack of essential information on such basic items as material properties and rock interaction. The Spokane Mining Research Center (SMRC) of the Bureau of Mines has been active in the field for the past 2 years, including research on fibrous reinforced shotcrete. IIT Research Institute, Chicago, under Bureau of Mines contract, is investigating physical properties of shotcrete as affected by (1) type of process (wet or dry) and (2) fast-set agents and controlle-dset cements. Already the contractor has shown the advantage of a regulated-set cement over normal cement and fast-set additives for the dry process. The regulated-set cements can produce high early strengths with no decrease in ultimate strength.

Jan 1, 1997

By Raoul Fernandez, Bernard Catalano, Guillaume Roux

The Thaumasia Joint-Venture, composed of Bouygues Travaux Publics, Soletanche- Bachy and Bessac, completed the construction of the underground section of line 2 of the Nice tramway, which comprised a 3.2 km twin track tunnel and four underground stations, in a particularly complex urban and geotechnical context. The density of the surface structures, as well as the presence of many historic buildings on its route made the construction of the tunnel even more sensitive, with a settlement threshold of Half an Inch. The joint venture faced a complex subsoil, varying from one extreme to another from highly plastic clay layers to fibrous peat and to cobbles with very high permeability, with artesian ground water, and with unforeseen anthropogenic obstacles in the tunnel section Due to the diversity of the problems encountered and their variability over short distances, the construction of the underground section of the Nice tramway, in its very sensitive urban context, undeniably constituted an unprecedented challenge.

Jun 13, 2023

By Jr. Stokowski

Topsoil for revegetation projects is in demand in many urban areas. In this case history, a large aggregate producer manufactured a topsoil from three waste materials. The topsoil was produced in a 200,000 m2 (50-acre) abandoned gravel pit that still had additional gravel under 10 m (30 ft) of overburden uneconomic to strip directly. The topsoil was produced by rotary mixing of sludge, overburden, and a lime admixture; solar drying; and stripping and stockpiling of the product. A major problem was an increase of topsoil drying times for stripping from 40 to over 100 hours when it was rewet by storms. The problem was solved by a research project that evaluated over 50 formulations and over 20 waste materials. . The final formula dried in 15 hours and contained 3-parts sandy mine spoil, 1-part sewage sludge, and 2 % spent-bed, a granular quick-lime produced during power-plant flue-gas desulfurization.

Jan 1, 1988

By V. Rajaram

A mine fire or roof collapse may necessitate the reversal of main fans to isolate the fire or provide an escapeway. Hence, to assist the mine operator in estimating the flow and pressure during reversal, Engineers International Inc. conducted a laboratory and field study of the reverse performance characteristics of main mine fans. Laboratory tests were performed using a 2.4-m (96-in.) diam vane axial fan to establish the forward and reverse performance characteristics under controlled conditions. Subse¬quently, a field test was conducted in a Colorado oil shale mine during which two 2-m (79-in.) diam fans were reversed. The data obtained indicate that reverse performance characteristics depend on the blade angle and the hub-to-tip ratio. The quantity in the reverse mode ranged from 30% to 65% less than in the forward mode, and the static pressure was directly proportional to the square of the quantity.

Jan 1, 1987

By B. J. Arnold

With the passing of the 1990 Clean Air Act Amendments, many utilities are opting to switch to lower sulfur coal to meet new SO2 emissions requirements. This lower sulfur coal may be from new suppliers or it may be from current suppliers that modify existing cleaning plants or build new plants to produce this higher quality coal. New, sophisticated coal cleaning simulators are useful tools for optimizing cod cleaning circuit operating parameters to maximize the production of clean coal that meets more stringent specifications for SO2 emissions potential. The examples in this paper were developed using the Coal Cleaning Simulator (CCS), running under ASPEN PLUS™, that was developed under a Department of Energy project cosponsored by the Electric Power Research Institute. With advanced sensitivity analysis and optimization features, CCS allows a quick, efficient, cost-effective review of coal cleaning plant performance to meet current production goals and to plan future changes in plant operating parameters or circuitry configurations.

Jan 1, 1995

By Frigyes Egerer, Pál Bárczy

Introduction Charles III, Holy Roman Emperor and King of the Austro-Hungarian Monarchy, established one of the first mining schools in Europe on June 22, 1735, in Selmecbanya (Schemnitz in German and Banska Stiavmica in Slovakian). The old city, built around the ancient gold mines, is shown in a contemporary engraving in Fig. 1. Charles&apos; historical decree consisted of 13 chapters and included: the deed of foundation, the definition of grants, instruction for educational policy and curriculum, disciplinary rules, and the appointment of personnel. The first professor of the school, Samuel Mikoviny, gave his first lecture the same year, in December 1735. The 250th anniversary of the establishment of the School of Mines was celebrated Sept. 2-4, 1985, in Miskolc. It was attended by representatives of other Hungarian and of several foreign technical universities. A silver medallion (Fig. 2) was issued to commemorate the occasion and a series of lectures

Jan 6, 1986

By E. Simoncini, S. Ulgiati, M. Raugei

A thorough Life Cycle Assessment of ilmenite extraction and processing to yield synthetic rutile (ERMS/EARS process) was performed according to ISO norms 14040 and updates. The LCA includes the parallel application of selected environmental impact assessment methods (as illustrated in Ulgiati et al. [1]), the results of which are compared and discussed. A MI value of 16 kg of abiotic matter per kg of output rutile is calculated, which is largely determined by the amount of coal that is employed in the reduction and drying steps. The Gross Energy Requirement is 3.33 * 107 MJ/kg, a value which we found to be comparable with that previously calculated by us for alumina. Finally, the increase factor of the Emergy Intensity from the raw mineral to the marketed rutile is 3.19, which points to a comparatively medium-low requirement for indirect environmental support. GWP and AP were calculated to be respectively 1.89 kg(CO2eq)/kg and 12.7 g(SO2eq)/kg.

Jan 1, 2005

By Fathi Habashi

CRYSTALLIZATION from aqueous solution is a simple and old method for the recovery of metal values from leach solution. Practically all the methods for the recovery of aluminum from clay are based on the crystallization of an aluminum salt from the leach solution. Differences in solubilities may be used to advantage for separating two metals from the same leach solution. The classical method of Marignac (1866), which makes use of the difference in solubilities of K2TaF7 and K2NbOF5 to separate niobium from tantalum, has been used successfully in the manufacture of these metals (Fig. 10-1). The slurry containing the metal oxides is dissolved in 70 % hydrofluoric acid, diluted, and heated near boiling. A potassium salt is added in sufficient quantity to form the complex fluorides of the niobium and tantalum present. The solution is filtered and allowed to cool. At room temperature most of the tantalum salt crystallizes out while the niobium remains in solution.

Jan 1, 1970