Search Documents

With commodity prices rising again and market conditions stabilizing, the Metals Economics Group (MEG) found that most mining companies increased their exploration budgets in 2010. In the groups 21st edition of the Corporate Exploration Strategies (CES), MEG found a 44-percent rise in the estimated worldwide exploration total for 2010. MEG found that the estimated total 2010 budget for nonferrous metals exploration reached $12.1 billion, reinstating almost two-thirds of the industry?s $6 billion in cuts to exploration in 2009. Nonferrous exploration refers to expenditures related to precious and base metals, diamonds, uranium and some industrial minerals; it excludes iron ore, aluminum, coal, and oil and gas. In 2008, exploration budgets were at an all-time high of $14.4 billion. This capped a six-year run in which budgets rose. In 2009, nonferrous exploration budgets dropped 42 percent in 2009 as the global economic crisis and declining prices for almost all commodities took their toll on the industry. Metals prices - the primary driver of exploration spending - have improved markedly since bottoming in early 2009, and have traded well above their long-term trends throughout 2010. In response, major, intermediate and junior companies have all increased their aggregate exploration allocations in 2010. In particular, the significant improvement in the availability of equity financings for the juniors over the past 12 to 18 months has allowed this group to account for the largest share of the overall increase in exploration spending this year.

Jan 1, 2011

By Rainer Antretter

The city of Garmisch-Partenkirchen in southern Germany is located at a main transit road to Tyrol in Austria and suffers of a very heavy traffic load. Therefore, the Kramertunnel as a by-pass tunnel is built to release/mitigate the traffic through the city centre. The 3,600 m long single tube road tunnel is designed with a parallel but smaller emergency tunnel and with cross passages, fitted with single- and doublesided emergency bays, a vent shaft, and an intermediate ceiling to separate fresh air supply from the road traffic. The tunnel, concrete lined along its entire length provided the challenge to find smart formwork solutions for quick set-up, repositioning, setup and pouring. Three particularly specific sections are discussed in this paper.

Jun 13, 2023

By D. Leppert

Clinoptilolite zeolite may offer attractive, cost-effective alternatives for remedial cleanup of old minesites, smelters and other sites with heavy metal contamination. Previous research demonstrates the relatively strong affinity of clinoptilolite for numerous metals and clinoptilolite displays a particularly strong affinity for lead (Loizidou and Townsend, 1987), one of the most toxic and problematic heavy metals. Since clinoptilolite can also selectively absorb some radionuclides and organic compounds, it may offer practical solutions to a wide variety of environmental problems.

Jan 1, 1989

By K. E. Hjelmstad

In the event of fire underground, it is essential that all miners be warned as quickly as possible. With mine air, rapidly depleted of oxygen and contaminated with smoke and toxic fire gases, any delay in the warning signal could have disastrous consequences. Unfortunately, present mine, fire warning systems, such as stench, audible or visual alarms, telephones, and messengers, are often slow, unreliable, and limited in coverage.

Jan 1, 1989

By Kostas Kaklis, Zach Agioutantis, Robin Flattery

Pillars are used as the primary support structures for underground mining to maintain stability by supporting the over laying strata. In the case of horizontal seams, the pillars are typically subjected to axial loading due to the weight of the overburden and/or abutment stresses, while in the case of inclined seams they are subjected to oblique loading due to both the vertical and horizontal in-situ stress.

By H. B. Miller

By its nature, underground metal mining is unlike any other business in the industrial sector. Operations are continuously exposed to economic risk as a normal consequence of mining due to uncertainties associated with the? deposit, excavation, and ever changing political, regulatory, and market conditions. Out pacing advances in productivity and technology, these conditions have contributed to the steady decline of underground hardrock mining in the United States. This paper investigates the trends and major factors believed to be responsible for this decline. Special consideration is given to changes in direct operating costs, labor productivity, and production capacity.

Jan 1, 1995

By D. J. Turk

Faced with decreasing production from the gold heap leach operation, Robinson implemented a drilling and blasting program on the leach pads in 1993. This program offset some of the negative effects of low ore permeability and short circuiting of leach solution that resulted in lower than optimum recoveries. The drilling and blasting program created new solution flow paths and increased gold recovery. Production and pulp assays at depth intervals, prior to and following drilling and blasting, reveal the degree of short circuiting and benefits of the program.

Jan 1, 1995

"In this review, the sintering process is first described and analyzed to identify the key factors affecting the structure and quality of iron ore sinter. Under fixed sintering conditions, the granulation efficiency, nucleus stability and primary sinter melt volume and properties of the iron ore are considered to have significant influence on the sinter structure and quality. Discussion is then focused on the effects of the chemical, physical and mineralogical characteristics of the iron ore on these key factors, and the consequences for sinter quality.IntroductionSintering is the most economic and widely used agglomeration process to prepare iron ore fines for blastfurnace use. In modern blast furnaces, particularly in East Asia, iron ore sinter typically constitutes more than 70% of blast-furnace ferrous feed. High sinter quality and efficient sinter production are thus required both to withstand extreme operating conditions and maintain the productivity of modern blast furnaces. At the same time, due to the increasing depletion of high-grade iron ore resources from large deposits, iron ore producers are moving toward developing an increasing number of deposits of much smaller sizes to maintain current production levels. It is therefore imperative for iron ore producers to develop long-term strategies to maintain the quality and consistency of the iron ore fines they are producing while exploiting these smaller, complex deposits. The iron grade, gangue minerals present, overall mineralogy as well as physical characteristics of iron ore fines being mined from these different deposits vary considerably. Overall, ores now have highly complex mineralogy, are becoming more porous and friable, and contain increasing amounts of gangue minerals, which will have important implications for the sintering process and sinter quality.Blending is one of the most effective options being explored by iron ore producers to deal with multiple small complex deposits. This allows the iron ore producers to reduce the number of products and take full advantage of the unique characteristics of each individual deposit to achieve long-term product consistency while increasing production. Blending is also a common practice in sinter plants as it is almost impossible to produce from one single ore a high-performance sinter mixture with the required processing characteristics. A typical sinter mixture used in Japanese steel mills (Nakano and Okazaki, 2007; Matsumura et al., 2013) often contains five or more ores to achieve balanced sinter quality and productivity with relatively low cost of raw materials."

Jan 1, 2015

By L. E. Mercando

The proposed Flambeau Mining Project is based on a high grade copper deposit located approximately one mile southwest of Ladysmith, Wisconsin. The project involves only the mining, crushing, and shipping of ore to facilities outside of Wisconsin for processing. The Wisconsin environmental regulations include provisions for identifying wetlands, the requirements for minimizing the disturbance of wetlands, and the need to establish new wet-lands to replace any wetlands which have to be disturbed.

Jan 1, 1991

By K. V. Raj, VASU GANGRADE

Airflow in large-opening stone mines is largely dependent on the natural ventilation due to the large cross- section area of the opening. The openings of such stone mines are typically twice or thrice the size of typical underground coal or metal/nonmetal mines. Due to the influence of natural ventilation, air velocities as well as the static pressure drop in the mines are low. Mines rely on auxiliary fans to ventilate active faces to reduce contaminant exposure to mine workers. The National Institute for Occupational Safety and Health (NIOSH) is conducting research on ventilation of large-opening stone mines to reduce worker exposure to dust and other contaminants such as diesel particulate matter (DPM). In order to reduce worker exposure to dust and DPM, an understanding of the airflow pattern due to auxiliary fans in the mine is needed. Under this research, NIOSH researchers are exploring the computational fluid dynamics (CFD) modeling to understand the airflow behavior in large-opening mines. In this paper, the team is presenting the results from three-dimensional CFD modeling of airflow in a large-opening stone mine and investigating the effect of a fan placement with the movement of trucks.

Feb 1, 2025

By Rollien R. Wells

The Bureau of Mines was created in 1910 by an act of Congress and subsequently directed to: "...conduct inquiries and scientific and technologic investigations concerning mining, and the preparation, treatment, and utilization of mineral substances with a view to improving health conditions, and increasing safety, efficiency, economic development, and conserving resources through the prevention of waste ..." Under this broad charter, the Bureau's responsibilities have changed and grown from an almost exclusive concern with coal and coal mine safety to the present emphasis on a full spectrum of mineral producing and consuming problems. In the past 30 years, the domestic consumption of coal, oil, gas, metals, and industrial minerals has more than quadrupled, in parallel with the rapid and enormous growth in industrial production. Of the scores of metals and nonmetals essential to the Nation's progress and security, many are scarce and difficult to wrest from domestic sources. Reserves of some ores are dwindling. Available ore resources are becoming leaner and more difficult to treat. In recognition of this many faceted problem, the Bureau has engaged in a continuing quest for new and improved technology to enable economic exploitation of marginal minerals and fuels, to find substitutes for minerals in short supply, and to create better materials to meet the expanding and diverse requirements of the growing economy. The current central concern of the Bureau is focused on meeting projected fuel, metal, and mineral demands at the lowest real cost by recovery from available resources by new and improved technology that minimizes waste, hazards, and social and environmental problems.

Jan 1, 1970

By J. Choi

For the first time, the influence of stearyl trimethyl ammonium chloride (STAC) as a collector, on the flotation behavior of lepidolite (Uljin, South Korea) was systematically examined in Denver Sub-A cells. Flotation tests were carried out by varying amount of STAC (50?200 g/ton), feed size (-65, -100, -150, and -200 mesh), and solution pH. The impeller speed of 1000 rpm, flotation time of 10 min and AF-65 (a frother) of 250 mL/ton were invariably applied. In order to complement flotation experiments, zeta potential measurements and XRD analysis were conducted. XRD results showed that the ores were mainly composed of lepidolite, muscovite, quartz, calcite and albite. In addition, zeta potential results showed that isoelectric points were about 2.5, 2.3, and 9.7 for quartz, albite, and calcite, respectively, and lepidolite was determined to be less than 2. Overall, the results of 3-stage flotation showed that Li2O grade and recovery tended to increase with increasing STAC dosage and decreasing feed size. In addition, Li2O grade increased with decreasing pH. The results were explained by the extent of the interaction between STAC and each mineral.

Feb 23, 2014

By Miguel Angel Ibarra

This paper describes the results of a digital computer simulation study in which the impact of the proposed truck dispatching on the overall mine productivity was investigated for an operating open pit mine. In the study, the existing operation was first simulated for a one-month period, using both the actual time study data and the computed cycle times. By adjusting certain input parameters to the simulation program, the actual one month production was first duplicated through simulation. Afterwards, the operation was again simulated in a dispatch mode. Comparison of simulation results under the dispatch mode, with the initial base case simulation results, showed a definite improvement in overall productivity with dispatching; i.e., approximately 10% gain for the operation. As expected, the results also showed that the extent of possible improvement did vary with the particular pit configuration being investigated.

Jan 1, 1980

By Yi Luo, Jianwei Cheng, Mingming Li, Lei Xiao

Concealed thermal events in longwall gobs present safety hazards for underground coal miners and can significantly interrupt mining production. The probable causes for such thermal events range from coal oxidation at slightly above ambient temperature to smoldering fires due to spontaneous combustion of the broken coal left in the gobs. Locating such “hot spots” is the key step for planning and implementing mitigation measures to bring such thermal events under control. If a mine section, or even an entire mine, has to be sealed, understanding the status of the sealed mine atmosphere is important for the decisions guiding subsequent actions. The gas composition data obtained through the tube bundle mine atmospheric monitoring system is firsthand information of great value. Fire ratios proposed by various researchers and derived from gas composition data are useful in determining the fire status and even approximating the source locations (Timko and Derick, 2006). However, the applicability of each of these ratios under particular conditions should be carefully evaluated. The use of properly combined fire ratios can enhance the certainty of analysis. The explosibility of a sealed mine atmosphere deserves primary concern for safety reasons during seal construction, idle time and reopening of the sealed area.Mine atmospheric monitoring data from a longwall mine with flame fire have been analyzed. Efforts have been made to identify the possible causes, locations and statuses of these events using the obtained gas data, as well as other ventilation, geological and mining parameters. The effect of injected inert gas to control the events has also been quantified. The explosibility of the sealed atmosphere has been determined using two methods.

Jan 1, 2012

Heap leaching has become one of the prime technologies used for the recovery of precious metals from low-grade ores over the past ten years. The recovery process involves mining and stacking the ore on engineered leach pads, with or without crushing and/or agglomeration, followed by leaching with a low concentration sodium cyanide solution. The metal-bearing, pregnant solution is then processed by zinc precipitation or activated carbon absorption to extract the precious metals. The leaching process continues until all economic metal values are removed at which time the spent heap leach pads, the leached materials and excess process solutions require decommissioning. The management of these solutions may present a potential challenge for successful and environmentally sound decommissioning due to their composition, volume or continuity of generation from the spent ore even though active leaching has been terminated. The principal objectives of solution management in decommissioning spent heap leach pads are to meet all operative environmental regulations in a cost-effective manner and to leave the pads in a condition where they do not present a long-term liability either to the operator or to the environment. This involves the reduction in volume of the residual process solutions and/or treatment of these solutions to where they meet applicable water quality criteria. In the past, the environmental and economic aspects of decommissioning and solution management have been overlooked or under-estimated during the planning of mining operations. As a result, there is a potential for long-term liabilities and costs to be recognized only at the end of active leaching, a time at which operating revenues and cash-flow are minimal. Therefore, the decommissioning process requires addressing at the mine planning stage and agencies now require that a plan for solution management after the cessation of operations be submitted prior to initiation of mining. This paper discusses aspects of process solution management during decommissioning, both in terms of quantity and quality, and how potential issues may be recognized and planned for in the initial stages of heap leach design.

Jan 1, 1992

By Galen G. Waddell

Several years of rock-burst research conducted by the Federal Bureau of Mines, in cooperation with the mining companies of the Coeur d?Alene Mining District, Idaho, in addition to progress made by others throughout the world, have led to a good understanding of the rock-burst problem. This paper describes conditions which have caused specific bursts, present capabilities of detecting stress buildup and bursts, control methods, and a suggested approach to analyzing any individual mine-burst problem.

Jan 1, 1970

By Pradip

Bastnaesite, a rare-earth fluocarbonate, was separated from associated calcite and barite gangue minerals in the Mountain Pass, CA rare-earth ore beneficiation plant by froth flotation using fatty acids (tall oil) collector, lignin sulfonate depressant and soda ash modifier after high-temperature (steam) conditioning with reagents. Starting with a feed grade of 7.6% REO, concentrates having a grade of 65% REO can be produced at a recovery of around 80%. A detailed investigation consisting of Hallimond tube microflotation experiments, bench-scale tests with a laboratory Denver flotation cell, and predesigned plant campaigns was made to delineate the underlying surface chemistry involved in this separation and to develop an alternate reagent scheme to enhance the selectivity of separation for this ore. Our results clearly demonstrate the superiority of alkyl hydroxamates to the conventional fatty acid collectors that were being used in the plant. Our study also indicates the possibility of achieving the desired selectivity with alkyl hydroxamates even at room temperature, thus obviating the need for steam conditioning. A critical review of the literature on rare-earth mineral flotation suggests the possibility of designing a more selective reagent combination for the beneficiation of Mountain Pass rare-earth ore, using a methodology based on ab initio molecular modeling computations.

By Dan Witkowsky

In an increasingly environmentally conscious world, mining's importance to society has often been misunderstood and even maligned by the public. Extreme and impractical ideas have often been presented to children because of the lack of accurate, timely resource materials available to educators. In the late 1960s. two mining engineers, S.P. "Pi" Warren and C.L. "Lindy" Barker, became aware of this situation. They proposed to develop a summer field course to provide a factual overview of the minerals industry for teachers. The pair believed that teachers could become better informed to educate students, and future generations, about mining. These two Colorado Mining Association (CMA) members felt that such a course could reduce much of the misunderstanding about this vital industry. This could be done by providing a balanced perspective of mining, not only for kindergarten-through-grade-12 teachers, but also for the students they would be teaching during their careers. Students who better understood the minerals industry could better formulate an unbiased view of it. The course would seek recognized authorities from industry, academia and government who would lecture in their respective fields of expertise. The course would provide a total concept of the coal, aggregate, metals and industrial minerals industries. It would include geology, geophysics, exploration, mining, processing, marketing, product applications, economic, mining history, careers, and environmental responsiblity. When possible, site visits would permit educators to view operations and to meet the men and women who are industry leaders. Teachers would pay a small tuition fee. The balance of the program expenses for each teacher would be paid through scholarships provided by industry and individuals. The "total concept" idea obtained the support of the minerals industry. The support of CMA's Education Committee and the Colorado School of Mines (CSM) was obtained in 1968. Colorado's Commission on Higher Education approved teacher recertification credits through CSM's Office of Special Progams and Continuing Education for those successfully completing the program. The first six-week series of classes presenting the total concept of the indus¬try was held at CSM in 1969. In 1977, the CMA Education Foundation Inc. (CMAEF) was established as a Colorado nonprofit corporation. The "Total Concept of the Mining Industry" (Total Concept) course was placed under its sponsorship. CMAEF is dedicated toward this continuing education program (Table 1). In 1994, the course was streamlined to four-weeks for six hours recertification credit.

Jan 1, 1997

By Benoit Gagnon

Mining of the Schefferville iron deposits began in 1954 on completion of the 574 km railway linking the mines and the St-Lawrence river port of Sept-Iles. Apart from crushing, no treatment of these ores was required before smelting. In the late 1950's, testwork began at Schefferville to develop a process for upgrading the extensive lower grade deposits containing 5l% iron with 15% silica (natural analysis). Engineering for 6.1 million tons per year Beneficiation Plant using cationic silica flotation and the A-C Grate kiln began in 1970 and the first pellets were produced in mid 1973. Production requirements and operating difficulties have restricted capacity to approximately 85% of design but ongoing improvements are being made continuously to attain design capacity.

Jan 1, 1980

By J. D. Mc Beth

The Carlin Gold Mining Company, a wholly owned subsidiary of Newmont Mining Corporation has been successfully operating an open pit gold mine and cyanide mill for approximately the past ten years. It is a unique operation in that about 20 percent of the mill feed is a carbonaceous ore refractory to cyanidation that must undergo a pretreatment stage developed for, and by, Carlin. The mine and plant are located in the Tuscarora mountain range is north-eastern Nevada near the towns of Carlin and Elko. Claims were staked at the minesite in 1961 and 1962. A drilling program was initiated late in 1962 and after drilling a total of 250,000 feet of rotary drill holes an estimated 9,300,000 tons of ore at a grade of 0.32 ounces of gold per ton was delineated.

Jan 1, 1975