Search Documents

By W. Edwin Dill

For the mining industry, the Internal Revenue Code and regulations offer a range of choices in arriving at the allowable depletion. Each case is essentially unique. Two prerequisites can optimize these opportunities: communications between the mining company's tax specialists and its technical staff; and an understanding of IRS definitions. For the latter, a logical starting point is consideration of exploration and development, since they precede production and depletion is unallowable prior to production. Criteria for selecting engineering and accounting options for exploration and development indicate the necessity of interaction between these company functions to achieve the most favorable tax position.

Jan 1, 1982

By S. Frimpong, G. Galecki

Dump truck tires are often used in long-haul roads in rugged terrain, with high rolling and grade resistances. These conditions increase the ton-kilometer-per-hour (tkm/hr) or short-ton-mile-per-hour (stmph)rating of tires, leading to tread wear, cuts and complete failures. The load-bearing capacities of these tires are sometimes exceeded, with truck overloading, overstressing, heating and subsequent failures. In addition, truck tire demand far exceeds the current supply capacity, with long lead ordering time. This condition has caused severe tire shortage, and the problem is expected to be sustained in the long-term. Industry has taken extensive practical measures to prolong tire service life with significant results. However, this problem can be solved through fundamental and applied research initiatives. This paper pioneers a research effort in tire service life using multibody physics, fatigue failure modes and soil failure dynamics to develop tire-road contact force dynamics. A virtual prototype simulator of the tire-road contact, using the CAT 775E (with standard tire 24.00R35) was developed and simulated within the MSC.ADAMS/NASTRAN environments. The results show the areas of the loaded tires with maximum Von Mises, principal and shear stresses, which could result in fatigue failure, tire wear and tear and blowouts. The maximum Von Mises stresses on the six truck tires are between 35 and 58 MPa. The maximum shear stresses are also between 19 and 33 MPa. These stresses will cause early tire failures given an average operating schedule of between 20 and 24 hours per day. The isolated areas with maximum stresses will be subjected to further studies to reduce stress intensity while preserving tire performance.

Jan 1, 2012

By S. A. Lang

Mine management in general, and mine maintenance in particular, has lagged in using computers as an effective management tool. SF Coal Corporation, in conjunction with the development of the new Lee Ranch Mine, is developing a computer-based maintenance system as an integral part of a total mine management information system. The system includes the ability to schedule and plan preventative maintenance on all rolling stock and mine facilities, project and track component life, and evaluate and schedule manpower requirements. The system hardware, shared by accounting, warehousing, engineering, production and management, consists of a multi-user, multi-processor micro-computer.

Jan 1, 1985

By L. Barnewold, A. Merchiers, M. Pütz, P. Jeschke, M. Dammers

The mining industry faces many difficult challenges, for example, lower ore grades, smaller and deeper deposits, and longer transportation distances. In the past, there have been remarkable innovations in both equipment and the types of mining methods for which it is used, which have resulted in economies of scale. This has led to an increased use of bulk mining methods, like sublevel and block caving, which has increased productivity and reduced costs. Haulage alone plays a major role. Current haulage techniques are a significant cost driver, which account for between 15 and 30% of the overall capital investment (capex) in a mine and are an increasingly part of the operating costs (opex). The paper introduces a simulation tool of main haulage system in underground mining. Therefore, performances and the costs of the three most common underground main haulage systems, rail, truck, and conveyor, are calculated using a developed modeling tool. The tool was applied and validated in a case study carried out with the LKAB Kiruna Mine in northern Sweden.

By S. S. Huyett

The opportunity to cooperate with the Mining Department of the Pennsylvania State University in their Student-Trainee Program is accepted by The New Jersey Zinc Company who believes that the participation in this type of a program will lead to a larger supply of high calibre engineers in mining. Trainees compete with other employees to earn the cost of their education while gaining practical experience in the mining industry. The practical experience is arranged to complement the technical education through a variety of work assignments. Job opportunities for the trainee are related to the work requirements of the Company and to the performance of the trainee. Management must consider and deal with a good many problems uncommon with regular, full 'time employees. For a number of reasons this program is recommended to other companies as a means to encourage outstanding young men who are interested in a career in the mineral industry to obtain a professiona1 education.

Jan 1, 1963

Numerous underground coal mine ventilation seals have been installed in the United States of America prior to 2006 and after implementation of the Mine Improvement and New Emergency Response (MINER) Act. Seal engineering, design, placement, and construction is regulated in industry, but post-construction monitoring of seals is limited to visual inspection of the outby face and seal perimeter, convergence measurement, and atmospheric monitoring. To monitor seal integrity and to provide safe working conditions, a form of non-destructive testing (NDT) is necessary to accurately reflect the health of the seal by detecting post-construction changes, deterioration, or defects within in-situ seals in underground coal mines. Previous research from the National Institute of Safety and Health (NIOSH) has indicated the potential for utilizing ground penetrating radar (GPR) for assessing in-situ mine seals. This paper provides an update to the assessment of proposed NDT methods for seal evaluation using commercially available GPR technologies and systems. Full-scale free-standing seals and large-scale seal specimens were analyzed with an array of GPR units from various manufactures using multiple frequencies.

Feb 23, 2014

By Thomas W. Smelser

A full-scale geotechnical model of a 15-foot (4.6 m) wide coal mine entry in correlation with computer finite-element analysis (FEA) is being employed at the Bureau of Mines Spokane Research Center for basic research on roof-bolt support systems. Physical and computer modeling of various coal mine roof-bolt reinforcement systems will increase our basic knowledge of how roof supports function. This information, in correlation with computer FEA and underground verification tests, will provide a basis for establishing safer, more cost- effective roof control plans and help establish guidelines for employing fully grouted and conventional bolting systems. The basic rationale for the research, research approach, methods and equipment employed, results to date, and future research plans are described in this paper.

Jan 1, 1982

By E. E. Caba

Copper smelter flue dusts containing arsenic are hazardous materials requiring environmentally accept-able disposal, preferably with re-source recovery under the RCRA and CRCLA regulations. However, the known resource recovery processes entail capital and operating costs greater than can be justified by the revenue of the recovered metal. Consequently, the smelting industry is tending to forego resource recovery in favor of encapsulation and storage in a certified class I hazardous waste site, or in a dedicated facility located at the source Superfund site. Order of magnitude costs for this option with portland cement encapsulation are estimated at $100 per ton, not including transportation. Industrial adoption of a new resource recovery process re-quires that its cost, including capital amortization, exceed the cost of encapsulation and storage only by the amount of the offsetting revenue from sale of metal. The lime-roast/ammoniacal leaching process is expected to meet this goal.

Jan 1, 1992

By John E. Miller

In recent years there has been increasing concern in the mining industry over the availability and high cost of diesel fuel to support mining operations. Unit Rig & Equipment Co. has been deeply involved with the development and testing of the newest designs for trolley assist. Beginning in dune 1980, Unit Rig modified and commissioned six 156 metric ton (170 short ton) trolley assist haulage trucks at two mine locations in South Africa. Operating haulage trucks with General Electric GTA 15E/776 drive systems were chosen for the tests since this size of truck represented the majority of the population of large size haulage trucks and the greatest technical development problems. Test operations have proven the feasibility of equipment designs in actual operation and preliminary economic data has convinced the operators to proceed with planning to modify their entire mining operation to use trolley assist. The initial capital investment incurred for trolley assist can be recovered in a short period of time. Following this quick capital recovery, mines will continue to realize lower operating costs through increased productivity and lower diesel consumption.

Jan 1, 1980

By M. C. Williams

As the flaws in the population balance model (PBM) comminution model are examined more deeply, further errors and problems were discovered. The Levenberg-Marquardt algorithm for systems of constrained non-linear equations was used to solve the dynamic PBM grinding equations to obtain the grinding selection and breakage rate functions. The fact that the PBM model equation Inverse Problem is degenerate or underspecified is demonstrated. Multiple solutions to the same PBM equations are provided. It is shown that there is no unique solution to the Inverse Problem unless additional constraints are provided or assumptions are made such as the Arbiter-Bhrany normalization assumption. The severity of the non-uniqueness problem for dynamic grinding is demonstrated. Each solution to a dynamic PBM, while giving the same prediction for a given grinding time interval, gives different solutions or predictions for mill composition for other grinding times. Actual experimental grinding data was assessed to determine the functionality of mill selection and breakage functions.

Jan 1, 1993

By David H. Carlson

Mechanical sorting of "poor" rock accumulated from past native copper mining operations has been under study at the Michigan Tech's Institute of Mineral Research for several years. Prior to this work, the poor rock dumps totaling approximately 9 million tons containing an estimated 35-70 million pounds of copper (1) have been considered mainly as a local source of road aggregate used from time to time and consequently of minor value. An electro¬mechanical sorting machine developed by International Sorting Systems Corporation of Santa Barbara, California has been tested for preconcentration of the waste rock before conventional milling (2,3). The ISSC machine has possibilities for underground preconcentration of crushed mine-run native copper ores. The objective of the study described here was to provide information about limi¬tations on sortability due to characteristics of the ore and present crushing practices. When the native copper mines were in operation prior to termination in 1969, two types of ore were produced, amygdaloidal and conglomeritic. In the first type copper occurs in vesicles left by gas bubbles entrapped during rapid cooling of the tops of lava flows. The conglomeritic ore beds consist of rounded pebbles and fragments cemented together by calcite, epidote, chlorite, and feldspar; the copper occurs around pebbles, in cracks, and sometimes as partial or total re¬placements of pebbles. The copper in the conglomeritic ore usually is in finer grain sizes than that in the amygdaloidal ore, and large (plus 4 inch) copper masses are virtually absent.

Jan 1, 1970

By I. WILKOMIRSKY, J. BECKER, F. Parada

The current processes that aim to purify molybdenite concentrates are not able to dissolve some copper compounds, hence limiting the processes. Typically, the copper content results are from 2 up to 4 weight percent in the last concentrate. Such values are still too high for the molybdenite concentrate to be further processed to molybdenum trioxide by roasting. In order to achieve lower levels of copper — but also avoid excessive molybdenite losses — a continuous sulfation-leaching process is investigated and applied successfully on a pilot scale. Additionally, a reactor prototype and its process parameters are proposed for a commercial plant.

Jan 1, 2023

By Isabel F. Barton, Christian A. Rathkopf, Mark D. Barton

Rhenium (Re) is one of the rarest elements on earth and is a designated critical element in the United States and European Union for its uses in superalloys. Unusually among critical elements, Re is produced entirely as a byproduct of molybdenite (MoS2) mining, as pure Re minerals are extremely rare. However, Re concentration in natural molybdenites varies from a few parts per trillion to tens of percent. There are few known consistent patterns and no firmly established reason for this variation, making it difficult to use molybdenite Re content as a proxy for metal grades, a vector to high grades, a clue to the geological and geochemical nature of the ore deposit, a guide to overall Re resources or for any other of the applications that have been suggested for it over time. 

By Bernard Y. Saltie

The White Pine orebody is characterized by a high lateral stress or highly faulted and joined conditions. Because of these difficult conditions roof support has always been a main concern. Mechanical bolts were widely used in the early seventies; however, it became apparent that major improvements in ground control were required if safe operation at White Pine was to be continued. The first step was taken in 1973-1974 with the testing of resin bolting. Record of caves and roof-falls with either type of support demonstrated superiority of resin bolting versus mechanical bolting - Safety was dramatically improved which was the absolute first consideration; however resin bolting was still more expensive than mechanical bolting. In order to generalize resin bolt installation, the second step was therefore to acquire special roof bolters compatible with resin bolting. The machine was to enhance the safety of the operation. This was achieved by the acquisition of the Secoma bolting machine equipped with an automatic bolting turret. Being a "hands off" operation the safety of the operator is total. Using a fixed taped attachment of the drill steel on the chuck a front guide and an automatic regulator torque thrust on the steel drilling in small diameter was possible. Being a fully automatic process only one operator is required per machine versus two operators with the conventional machines. The two main objectives were reached enabling the extension of resin bolting to the whole mine.

Jan 1, 1980

By D. W. Tuckwiller

Electroplating is a widely utilized but little understood process. The fact that the average person is in contact with dozens of plated items daily without even being aware that they are electroplated is evidence of the success of the process. Although a complete explanation of electrodeposition involves thermodynamics and modern theories of bonding and catalytic reactions, in its simplest form the process conforms to the following description. A metal salt dissolved in water partially dissociates into negatively charged and positively charged ions. In the case of nickel sulfate dissolved in water, for example, a portion of the salt dissociates into positively charged nickel ions and negatively charged sulfate ions. If an electrical potential is applied between two electrodes in this solution, the nickel ions migrate toward the cathode and the sulfate ions toward the anode. The negatively charged cathode has a high concentration of electrons, which combine with the positively charged metal ions to form neutral metal atoms with a stable electron configuration. These insoluble atoms thus form a deposit on the cathode.

Jan 1, 1970

By Michael W. Roper

McDermitt Mine is located in northern Humboldt County, Nevada, approximately 5 miles south of the Orgeon-Nevada line (Figure I), within the Opalite Mining District. The operation is a joint venture between Placer Amex Inc., San Francisco, and Mineral Exploration Company Ltd., a limited partnership. The McDermitt orebody possesses a discontinuous, gently dipping blanket-like form within 150 feet of the surface over an area 2200 by 2500 feet. The ore zone averages 20 feet in thickness. The ore minerals consist of cinnabar (HgS) and corderoite (Hg3S2C12) deposited parallel to bedding within argillized, Miocene age, tuffaceous lacustrine sediments. Exploration indicates reserves of approximately 3,000,000 tons ore at a grade of 10 pounds mercury per ton (0.5%) An open pit mining operation utilizing scrapers and bulldozers supplies a concentrator with 700 tons of ore per day. The milling operation consists of autogenous grinding, flotation concentration, concentrate dewatering, and tailing disposal, with a design capacity of 100 tons per hour. The furnace section consists of a concentrate filter, vertical six hearth furnace, mercury condensing system, and exhaust gas scrubbing systems. It has a design capacity of 1000 pounds of dry concentrate per hour. The McDermitt orebody is situated about 2000 feet north of the Cordero Mine which, with adjacent properties, produced over 115,000 flasks (76 pounds per flask) mercury from 1941 to 1972' Two other major mercury producers in the district have been the Bretz and Opalite Mines, located in southern Malheur County, Oregon, within 5 miles of the Oregon-Nevada line. Bretz and Opalite have produced about 14,800 and 12,370 flasks mercury respectively, from 1926 to 1965.1/

Jan 1, 1976

"Mine ventilation is in every underground mine a crucial process to ensure mine safety as well as acceptable working conditions. On the other hand is also a major cost factor depending on air requirement and air resistance. Due to the fact that the special layout of mines develop over time, ventilation systems change as well. This may result in complex systems which are suffering severe problems and low efficiency. With attention to the mine safety and costs, ventilation systems have to be controlled repeatedly and optimized continuously to fit changing conditions. The project “Improvement of ventilation systems in narrow vein mines” has been commenced with measuring and data collection in the Bogala Mine, Sri Lanka. This over 150 year’s old graphite mine consists of about 20 levels. The resulting ventilation system is highly complex and suffers problems like high temperatures and humidity as well as a mixing of fresh and used air on lower levels. To solve these problems and to optimize the system the complete ventilation system had been measured on-site first. The gained data have been used for simulations to develop and select an optimal and cost efficient solution. OBJECTIVE As an important process in mining ventilation is a major cost factor and can determine the economic feasibility of a mine. Due to the production mine layouts develop over time and mines increase in size and depth while the ventilation system becomes more complex and may suffer severe problems and inefficiency. Therefore mine ventilation systems have to be controlled and optimized regarding the general requirement of mine safety and health of the miners as well as the costs. Depending on the deposit type, depth, mining method, climate and as well corresponding laws and regulations the possible solutions are varying strongly. The work carried out paid special attention to the improvement of ventilation in narrow vein mines in tropical climate, in this case the graphite mine “Bogala” in Sri Lanka, South Asia."

Jan 1, 2015

By Errol L. Montgomery

The region of metalic ore deposits in northern Chile, southern Peru, western Bolivia, and northwestern Argentina occurs in arid zones at altitudes as high as 4,600 meters. Because surface water supplies are meager, new mines require unexploited sources of water. Prolific groundwater aquifers occur in salar basins in this region of the Andean Highlands. Exploration water wells have been constructed and aquifer characteristics have been tested in eight salar basins. Results indicate groundwater quality is good. Aquifer transmissivity and storage computed from results of pumping tests indicate maximum production water well capacities in excess of 170 liters per second.

Jan 1, 1982

By Paul W. McGann

This paper presents a methodology for long-range studies of petroleum supply, to meet projected demands, that involves modifications of procedures used previously. This paper continues a series of papers on this general topic in the AIME, the most elaborate recent one being that by Warren Davis given in February 1958. The procedures considered here begin with the assumption that the governmental framework of regulations and taxes remains fixed- but that price changes. After .these procedures have been reviewed, the effects of changing certain governmental controls, will be considered in order to judge their potential effects on future supply. This is an essential step because controls cannot be expected to' remain static in a situation changing as much as the petroleum. industry and because such changes are within-the scope of alternative ways of adjusting to impending problems. The first procedure begins with: a) trends in drilling success, b) relation between field income from oil and gas and footage drilled, c) declines in capacity from production, d) trends in capacity of new and producing wells, e) all monetary values are in constant 1958 dollars, and f) target amounts of domestic crude petroleum production. 'From these components projections are obtained of: 1) numbers of future producing wells required, 2) footage drilled, 3) new wells drilled, 4) crude oil found, 5) capacity of producing wells, 6) completion costs, 7) finding costs, 8) production costs, and 9) average wellhead crude oil price consistent with the footage-field income relationship.

Jan 1, 1960

By H. C. Rolseth

The first step in the quarrying of granite, following removal of any overburden material, involves the freeing of large blocks from the formation. For many years the use of explosives was the accepted method of obtaining these blocks. Even today there are operations where this is considered to be the most economical method even though it does result in a high percentage of damaged stone. In more recent times the preferred procedure at most quarries has been to produce a continuous vertical cut or slot completely around the block to be separated. Originally, this was done by drilling a series of closely spaced holes around the block and breaking the web between the holes with a chisel-like tool known as a broaching bar. The machine used in this mechanical method of producing the relief slot is known as the channel bar. The modern day approach to the production of continuous channels was introduced to the industry around 1955 by the Linde Division of Union Carbide Corporation. The method employs a small rocket - jet burner producing a high temperature, high velocity exhaust flame which when directed against the granite causes it to disintegrate. This method, which has come to be known as "Jet Channeling", is now used by practically every major granite producer in the United States and Canada.

Jan 1, 1968