Search Documents

By I. Martinez-Dominguez

In September 1992, mining in Mexico was opened again to foreign investment by President Salinas-de Gortari, after thirty years of "Mexicanization" of mining industry which limited foreign participation up to a 49 % (or 34 % in case of national reserves) on a Mexican mining corporation. During said period mining in Mexico was controlled by four or five big mining companies and besides mining production was focused mainly on silver, lead, zinc, copper and fluorspar. Suddenly in middle of a big crisis on Mexican mining industry due to low prices of minerals in the world and also in a period on which it seems that mining industry in the United States and Canada has been condemned to die for environmental reasons, it appears a new Mexican Mining Law to permit foreigners to participate in mining in Mexico' trough Mexican mining corporations that they may control up to 100 %

Jan 1, 1994

By F. Touboul, M. Thiercelin, K. BenNaceur

Introduction The need to develop accurate predictive hydraulic fracturing simulators arises from the consideration of vertical containment for the fracture. Fracture height growth from a pay zone into adjacent layers has been shown (see Cleary [I]) to depend on three sets of parameters for the different strata: - elastic properties, - closure stress variations, and, -fracturing fluid leak off, and poro-elastic stresses. Qualitative analysis of the effects of these parameters has been reported in the literature. The first effects were described by Van Eekelen, using simple elasticity considerations [2]. The effect of stress variations was described numerically by Simonson and a1. [3] and experimentally by Thiercelin [4]. Effects of back stresses induced by fluid invasion on fracture propagation were considered by Cleary [5]. In order to couple these effects, a numerical code al- lowing the simulation of three dimensional growth of a hydraulically induced fracture has been developed with the ability of representing the effects of heterogeneities on fracture lateral and vertical extension. The model is based on a new variational formulation of the boundary integral representation of three-dimensional elasticity. The fluid flow and elasticity equations are solved using a moving mesh representation which offers enough flexibility to enable the simulation of any closure stress distribution. Simpler models representing fracture height growth (P3DH models) have been developed [6] [7] that approximate the fracture by a series of one dimensional segments, and the limitation of such approaches is examined in this paper. 1 Description of the model 1.1 Fracture Geometry Hydraulic fracturing simulations involve the coupling of solutions to elastic deformations, fluid flow in the fracture, and fluid leak off into the formation. Since the use of direct solution techniques (i,e,,3D finite elements) is prohibitive, the method used in this study is baaed on a boundary integral representation of the 3D elasticity equations. 1.2 3D Models The classical representation of the problem of a fracture in an infinite medium by boundary integrals is [8]: [ ] where u is the unknown displacement field, r n is the traction operator, I? is the fracture surface, and K is the Kelvin tensor of fundamental solutions to the elasticity operator. Using the notation: [ ] for the displacement discontinuity (or fracture width), one can attempt to solve the boundary integral relation using surface integrals (91 or the displacement discontinuity technique, first introduced by Crouch [lo], and extended to three-dimensional problems [Ill. However, numerical problems arise since the Kelvin tensor has a singularity in

Jan 1, 1986

By Cayo Soto

Mining activity is important for the development of humanity. This development must be understood from the Academy where it allows showing alternatives for the industry performance. Likewise, these mining companies need to improve their results. Historically, a few years ago the application of the ESG (Environmental, Social and Governance) criterion was verified, which is positioned as a factor/regulator in the design of the performance of industries in general. ESG as an integral part of the concept of sustainability serves as a tool to conceive mining without conflicts and with a reputation based on trust in the interrelation of the university, industry and society. Therefore, the academy must strive for new knowledge in a way that allows it to continue in the virtuous circle of constantly feeding it. In this context, the best mining practices are implemented in constant questioning of their activities. The scientific essence of the industry supported by the academy developed in an operational dynamic is addressed. Finally, the objective of this research work is to interrelate 3 variables: ESG, Academia, and the Mining Industry, where the transition of knowledge and the role of each variable in relation to each one can be understood. This allows for an additional understanding of mining in the future with new mental attention.

Feb 1, 2025

By J. G. Pippenger

The Coteau Properties Company's Freedom Mine is a surface lignite mining operation utilizing large draglines, trucks and shovels, tractor-scrapers, and bulldozers to uncover a single coal seam. In 1989, a work order system was instituted to record data by equipment type, cost, productivity, and distance, and to provide historical information for planning the most efficient and economic use of each equipment type in the mining operation. This report explains how the work order system was initiated, what data is tracked, and how the data is utilized for equipment and project scheduling.

Jan 1, 1994

By D. A. Norrgran

The process of magnetic separation is based on the differences among magnetic susceptibilities of various mineral species. Performed either wet or dry, the separation has application in both the recovery and concentration of value minerals and in removing deleterious mineral constituents from a product stream. There are two major catagories to be considered when addressing magnetic separation of minerals. The first catagory refers to particle characterization and relative differences in magnetic susceptibility. The second catagory refers to design parameters and the magnetic field generated by the separator.

Jan 1, 1987

By A. Mei, F. Amadini, F. Cernera, D. Baliani, A. Flor, M. La Morgia, F. Sassi

The risk of TBM jamming because of squeezing rock mass or excessive caving (instability of the cavity) conditions is always a focal point while boring long and deep tunnels with shielded TBMs. Mechanized excavation provides a large amount of real-time data, for each machine’s parameters. Several analyses have been executed to assess the correlations between different sets of TBM parameters for the exploratory tunnel. Instead of analyzing the full dataset, a different approach is proposed, with data processed sequentially to simulate the real excavation situation. The probability distributions are recalculated together with their statistical parameters while advancing. This approach is extended also to the training of a Machine Learning model able to foresee the behavior at future rings based on past rings (using a Recurrent Neural Network). The predictions show a promising first step toward creating practical tools that can assist contractors and designers to correlate and predict TBM excavation data. These tools will assist to predict and quantify high risk situations that could arise during excavation.

Jun 13, 2023

By Scott G. Britton

This chapter discusses the necessary construction techniques for installing coal mine ventilation devices. Included in the discussion are the major air controlling devices called over- casts, regulators, stoppings, and doors. Under-casts, although a valid device, are used infrequently in coal mining and are not discussed here. Typically, coal mines require a great many ventilation devices to control the air movement. Post-I969 mines have had to design their air systems to comply with the Federal Coal Mine Health and Safety Act (CMHSA) as discussed in Chap. 1. Pre- 1969 mines have had to redesign major portions of their systems to comply with the basic components of the law such as separation of air courses, single unit split ventilation, and minimum air quantities. It is not uncommon, therefore, to find a large mine (2.0 Mt/a) requiring several hundred overcast installations (permanent, as well as repeat construction), plus doors and regulators placed among a thousand or more stoppings. When each of these devices is subject to leakage from installation and weathering defects, the importance of effective construction becomes evident. An historic rule of thumb for average mine ventilation says that about 70% of all the air pressure generated by the mine fan is lost between the portal and the working faces. Of course, this rule is subject to many factors, but the message is clear: there is a tremendous inefficiency in controlling leakage through common air devices. This chapter strives to present a standard approach and design alternatives which can go a long way in reducing this leakage, and hence, ventilation costs. Historically, mine ventilation has progressed from natural, or draft ventilation, to fire-induced ventilation (Fig. l), furnace-fired centrifugal fans and finally, to today's modem mine fans. Underground controlling devices have been in use in the coal mines since the late 1600s, but the CMHSA of 1969 was the real turning point for mine ventilation. Minimum quantities and velocities of fresh air were required for mining, forcing coal operators and engineers to reevaluate and improve their systems. As a consequence, the cost for ventilating air increased. Today, companies face a variety of choices among design alternatives, materials, labor, and costs of ventilating devices for their mines. The best approach for any individual company or mine is determined by (1) the needs of the mine, and (2) the local design parameters. In my discussions of ventilation construction I shall be fairly general in terms of device installation steps, where specifics are warranted for clarification, I will include this information.

Jan 1, 1983

By Brian McInnes, Joseph A. Sopko, Behzad Khorshidi

"The Port Mann Main Water Supply Tunnel involves a 1km long tunnel beneath the Fraser River from Surrey to Coquitlam, BC. At depths of up to 60 m below ground, the earth pressure reached 6 bar. The tunnel is constructed using an EPB TBM and gasketed precast concrete segmental liner. The tunnel and two shafts were constructed in a variety of soil conditions ranging from soft to stiff clays and silts, to compact to very dense sands and gravels. After approximately 800m of mining, a very dense and highly variable soil group consisting of cobbles and boulders halted the TBM. Several options were considered to stabilize the TBM face so an intervention could be conducted. Although de-watering was considered, there was risk of settlement to the Port Mann bridge piers, which was within 500m of the tunnel. Hyperbarics were also considered, however, the cost, schedule and uncertainty of the work that needed to be done, made it a risky option. Ground freezing by Liquid Nitrogen was chosen as the best solution, which would provide a frozen block around the face of the TBM. A temporary platform on the river was designed and constructed to enable drilling and installation of the freezing pipes and temperature monitoring equipment. The operation required close coordination among the tunnelling, marine and freezing sectors. Following the intervention, the TBM successfully broke through the reception shaft, and the remaining project was completed. This paper describes the design, construction and operational approaches used for the freezing and serves as a basis for future projects requiring expedited ground freezing."

Jan 1, 2016

By Joel K. Waterland

GENERAL DESCRIPTION Open cut-and-fill stoping for many years was prob¬ably the most widely used mining method in under¬ground metal mines. Then for a time this method was largely supplanted by the blasthole stope. It again be¬came popular as many mines reached depths or grades where methods requiring large open voids to remain open for extended periods of time became unsuccessful, often as a result of excessive dilution. The open cut-and-fill method is very flexible and is readily adaptable to almost any ore body. The standard application requires that a slice of ore usually 2.4 to 3 m (8 to 10 ft) thick be removed from the back of the stope, and as the ore is taken down, the back is dressed and rockbolted. After the back is secured, the broken rock is removed through rock passes to the level below. When the rock has been removed, the rock passes are extended upward the height of the ore removed, the stope is backfilled, and another cycle is mined. This method is best employed in plunging ore bod¬ies with considerable vertical extent, ore areas that re¬quire selective mining, ore areas where weak wall con¬ditions exist, and ore bodies that have an ore value that will carry this relatively expensive mining method. Blast¬hole stoping, shrinkage stoping, and other mining meth¬ods that do not employ rock passes in a stope are not efficient in plunging or flatly dipping ore bodies because the footwall makes ore removal quite difficult. Since mining is accomplished by taking down slices of the back, only small areas of the wall rock are exposed at any one time, and these only for short periods. Due to limited back height, areas of uneconomic rock may be left in place, or they may be mined and the material gobbed in the stope. Because the miners in the stope must work under freshly blasted areas, the amount of ground control is usually great. The volume of rock that is broken during one section of mining is relatively small and the amount of nonproductive work required is high. This results in limited productivity for the scope and, be¬cause of the nonproductive work that must be done on a regular basis, the production from the stope may be quite cyclical. SUITABLE ORE BODIES The open cut-and-fill method may be adapted to al¬most any type of ore body with a relatively high vertical extent. The ore body must be accessible at both top and bottom as well as at regular intervals throughout its vertical extent. Although adaptable to most ore bodies, the method is probably best employed where the ore has poor con¬tinuity and where most types of bulk mining would pro¬duce excessive dilution. In areas of poor ore continuity, the capability of continuous and extensive sampling dur¬ing the mining of each cycle makes this method very desirable. This capability also minimizes the amount of evaluation sampling that must be done before mining is started. Because of the extractive system used, the size and shape of the stope may be as readily changed as the sampling mandates. Probably the only ore characteristic demanded is that the ore has strength enough to be sup¬ported through the use of rockbolts or cable bolts dur¬ing the mining and backfilling cycles. Good planning, systematic sampling, and careful supervision will pro¬duce a product with less dilution than any other open stoping method. PLANNING Evaluation Planning Once it has been decided that the open cut-and-fill method would be the most efficient for mining a par¬ticular ore body, the next considerations would probably be the availability of an economical backfill material and the selection of an efficient transport system for this material. Although hydraulically transported mill tail¬ings are the most widely used product, this is not always practical due to mill location or the quality of the tailings. In such cases, backfilling may be used. The type of backfill and the type of equipment used will determine if a floor or capping on the backfill is required to minimize dilution during ore removal. The early selection of rock removal equipment is im¬portant since equipment usually determines the amount of development work required to bring a stope into pro¬duction and the size of the openings needed. The size and continuity of the ore body will usually determine the type of loading equipment. The use of slushers or load¬haul-dump (LHD) equipment captive in the stopes will minimize the amount of development. If the ore con¬tinuity is such that a ramp system for extraction can be used, the cost of development will be increased but the flexibility of continuous mining will minimize the cycli¬cal nature of the production. The height of the mining section usually is deter¬mined by the strength of the wall rock and the amount of back bolting required. Once this has been decided, the appropriate drilling equipment can be chosen. The number and sizes of the rock passes employed depends upon the type and size of the extractive equipment and the type of backfill that is to be used. Since the miners must enter and leave the stope each shift, the level inter¬val is usually maintained at approximately 45 m (150 ft). Access from the level above into the stope must be main¬tained at all times. The employees perform all the work in the stope and adequate ventilation must be provided. Stope Planning Due to the flexibility of the method and the vari¬ability of the ore zones, layout is usually done on a stope basis. In areas where continuity is a problem, the size of the stope is usually determined by the boundary of the ore (with all of the ore within that boundary being removed). In areas of good continuity where ramps are to be used, the length of the stope may be determined by the length of time each of the cycles (preparation, back¬fill, mining, and ore extraction) requires. The ramp work is then laid out so that access to the various parts

Jan 1, 1982

By N. Moony

The benefit of gravity separation in improving total gold recovery in grinding circuits has been outlined in a significant number of papers to date. However, the use of batch centrifugal concentrators (BCC) as an industry standard to extract gold has limited the potential for maximizing gravity recoveries -particularly in coarse gold deposits. This is a reflection of the high upgrade ratios obtained by BCC's which has an inverse relationship with recoveries. Survey work in Australia has indicated that installation of the InLine Pressure Jig as an alternative to the Bee will significantly increase recoveries of gold by gravity and, accordingly, increase total gold recoveries and lower operating costs.

Jan 1, 1998

By Kourosh Shahriar

The occurrence of rock falls in underground coal mines entails detrimental effects as fatal or non-fatal injuries on workers, stoppages in mining operations and breakdown of equipment. In this paper, a risk assessment approach on the basis of a decision analysis trend is employed in order to assess the possibility of and manage roof falls. Risk is then assessed by determination of likelihood of occurrence and the cost of consequences (outcomes). In this regard, collected real roof fall data from Tabas and Kerman coal regions comprising of several underground coal mines are used. It is concluded that the annual accidents due to the roof falls occurrence in the all investigated mines are so high that it is economically feasible to improve the support systems and to implement a suitable educational program as well as an accurate supervision and other elements of safety management.

Jan 1, 2009

By R. Reddy Kallu

Prior to July 2007, the only accepted method by MSHA for evaluating the mine seal design and performance is the full-scale explosion tests conducted in the NIOSH?s Lake Lynn Experimental Mine (LLEM) for deeming a seal design suitable for use in U.S. coal mines. Since the new regulations came into effect use of these conventional full-scale explosion tests for evaluating mine seals for the new elevated design standards may not be practicable. Generation of such high explosion pressures in experimental mines is dangerous and may cause permanent damage to the testing facilities. Further, they require significant amount of time, labor and money. Considering these factors, there is a need to develop scientific methods for evaluation of new seal designs and for understanding the dynamic seal response. This paper tries to address the reinforced concrete (RC) seal design using the three dimensional finite element based explicit software ABAQUS. Full-scale explosion test data available from NIOSH?s LLEM on 20 psi reinforced concrete seal is used for validating the numerical models. Further in this paper, based on the results from the validation models, a reinforced concrete seal is designed for 120 psi design standard for typical entry dimensions.

Jan 1, 2009

By Hamid Maleki

Mine seismicity is influenced by the mechanical properties of both near-seam rocks and overburden and the prudent selection of mining methods and mine layout designs. Using finite-difference modeling, experience in many U.S. mines and measurements of the pressure arch width, the author has reviewed the engineering design factors that control seismicity in room-and-pillar retreat operations for stiff stratigraphic conditions in deep western U.S. mines. By back analyzing the overburden response in now understood to have been inadequately designed historic room-and-pillar mine, the overburden collapse mechanism is addressed as well as the need for improvements in designs including panel and barrier pillar widths, and sequence of retreat.

Jan 1, 2009

By Slawomir Bock

One of the fundamental issues having a great influence on the safety of operations performed in underground mines is the support of workings which should assure their stability in a given geological setting and mining-technical conditions during the life of their use. The process of designing and planning support for roadways may use analytical and empirical, as well as numerical methods. In view of the rapid increase in the data processing capacity of computers and the development of more and more enhanced software for numerical modeling, it seems to be advantageous to use numerical methods in searching for design solutions ? especially in the case of non-typical mining and geological conditions and in cases that need to take into consideration a great number of factors. The assessment of rock mass quality is of basic significance in designing mine supports. Fractures, dividing the rock mass into blocks, have an essential influence on the stability of the rock mass and underground construction. This paper presents examples of the fundamental underground investigations on the rock mass conducted by the Department of Extraction Technologies and Mining Supports of the Central Mining Institute in Poland, such as: penetrometric tests, introscopic examination, laboratory testing of rock samples and ground penetrating radar. Moreover, this contribution also presents examples of applications of three-dimensional numerical modeling for the purposes of stress-strain analysis of the rock mass around mine workings and computer-aided support design by means of FLAC3D (developed by Itasca) and Cosmos/M (developed by Structural Research and Analysis Corporation).

Jan 1, 2009

By David Conover

The El Boleo Copper Project is currently in the final design stages for development of a 3-MM-tonne/yr underground copper mine located in Baja California, Mexico. The nearly horizontal mineralized zones are amenable to exploitation by conventional mechanized coal mining technology using continuous miners, shuttle cars, and belt haulage. The mine design resembles a typical full-extraction coal mining operation utilizing a sequence of mains, sub-mains and production panels. Due to numerous faults, mining will be conducted as several small adjacent mines accessed through adits from large arroyos cutting through the mine area. Up to four seams may be mined in some areas with a maximum overburden depth of about 250 m. The ore zone is relatively weak and plastic, subject to extensive creep over time. The mine workings will pass through areas of historical shortwall mining panels where the ground has flowed into old entries and gob areas, and then reconsolidated. A small test mine was developed to evaluate mechanical cutting performance, roof-bolt anchorage capacities, roof and pillar stability and caving behavior. In-mine measurements were combined with two- and three-dimensional FLAC models to evaluate alternative development and production pillar designs. The paper will discuss the various factors influencing ground stability at the El Boleo project and the strategies employed in developing a suitable ground control design.

Jan 1, 2009

By Mike Amick

As virgin coal reserves dwindle, more and more mines are being opened in areas with previous mining. As addressed in this conference before, there are solutions available for designing mines extracting coal from reserves with known underground workings above or below the target seam. Often times, however, mining begins with limited knowledge of the underground workings. Even with careful planning, the proposed design has limited success because the ?facts? as presented during planning turn out not to be as accurate as one would like. At National Coal?s Mine #14, mining the Walnut Mountain seam, after driving the main entries in some 34 crosscuts, it was found during routine mine examinations that the pillars had separated from the roof in a few areas of the mains. Immediate roof conditions proved to be sound but questions arose concerning the stability of the main roof and floor. Core tests were done to better determine the rock strengths and characteristics. The paper presents the ideology used to tackle the effects of mining over old works in an operating coal mine. This paper discusses the analysis of the symptoms observed and the steps taken to ensure that this pillar separation was caused by the underlying old workings and that the separation was expected and controllable.

Jan 1, 2009

By W. C. Patrick

Introduction The availability of a thorough, simple-to-use roof fall classification system is desirable for several reasons. First, such a system would expedite the reporting of falls for the purposes of estimating material removal costs, analyzing damage levels, and complying with federal regulations to report falls in certain areas of the mine. Second, the classification system would allow the mining engineer to record falls routinely with little time and effort expended. This would encourage him to make observations concerning what type of roof support would work best in a given situation. Third, and probably most important, an adequate roof fall classification system is the first step toward developing a means of predicting the occurrence and extent of future falls. It was with these three reasons in mind that the following classification system was developed. The type of classification chosen reflects the background of the developer and the intended purposes of the system. Hylbert has proposed a geologic-based classification which groups falls as to structural and compositional origin. The need for similar systems is noted by Cox and by Ferm and Melton. Each of these researchers is confronted with a situation requiring a relationship between local geology and roof fall occurrence. Such a relationship would allow the prediction of the relative frequency of falls from a knowledge of local geologic features. The current research is aimed at fulfilling somewhat different requirements, as noted above. Fall geometry has been chosen as the basis of the classification system so fall type can be reported independent of local geological, environmental, and tectonic conditions. This approach parallels that used in the common slope failure classification with groups failures relatively independent of

Jan 1, 1977

By Martin B. Hudson, John Yao, Matthew R. Crow, Yiming Sun, John T. Waggoner, Roozbeh Geraili Mikola

"The Wilshire Grand redevelopment project in downtown Los Angeles includes construction of a new 73-story tower. Construction required excavation up to 93 feet deep (28 m). The south side of the excavation, up to 57 feet deep (17 m), required placement of shoring within about 6 to 10 feet (1.8 to 3.0 m) horizontally away from a 400-foot-long (122 m) section of one of the existing Los Angeles Metro Red Line twin subway tunnels. These tunnels were constructed using a 22-foot-diameter (6.7 m) digger shield, and were initially supported with expanded, precast concrete segments, with final cast-in-place reinforced concrete lining. The temporary shoring system for the deep excavation consisted of soldier piles generally spaced at 8 feet (2.4 m) on center with multiple levels of tieback anchors extending above the subway tunnels. The lowest level of bracing consisted of rakers supporting walers attached to the soldier beams because installation of tieback anchors at that level would conflict with the tunnels. Numerical analyses were performed to predict tunnel movement caused by the excavation and its effects on the train operations. This paper describes the numerical modeling, tunnel and geotechnical instrumentation and monitoring program, and comparison of the computed and observed tunnel responses to the deep excavation and tower construction. With increasing urban redevelopment in major cities, the project is a valuable case history for excavation adjacent to existing tunnels. INTRODUCTION The Wilshire Grand redevelopment project includes the demolition of a 16-story hotel built in the early 1950s and the construction of a new 73-story tower in downtown Los Angeles (LA) that will be the tallest building in the western United States. The project site is situated on approximately 2.7 acres (1.1 Ha) of land bounded by Figueroa Street to the east, Wilshire Boulevard to the north, Francisco Street to the west, and 7th Street to the south (see Figure 1a). The new tower is being constructed by Turner Construction for Hanjin International Corporation. Construction of the basement and foundation of the new tower required excavation up to 93 feet (28 m) deep. Shoring was designed by Cefali & Associates and installed by Malcolm Drilling Company. Along 7th Street, an excavation up to 57 feet (17 m) deep required shoring to be installed within about 6 to 10 feet (1.8 to 3.0 m) horizontally from an existing 400-foot long (122 m) section of one of the LA Metro Red Line subway tunnels (see Figure 1b). The tunnels, extending from the 7th/Metro Station to the Westlake-MacArthur Station, were constructed in the late 1980s and early 1990s with an excavated diameter of approximately 22 feet (6.7 m). They were initially supported with expanded, precast concrete segments with a final cast-in-place reinforced concrete lining. The existing hotel was demolished in 2012 and 2013, with shoring installation and excavation for the new basement occurring as the demolition occurred. At the time of writing, January 2016, the structure of the building adjacent to the tunnels is largely complete."

Jan 1, 2016

By Takashi Sasaoka

About 200 M tons of coal were imported into Japan in 2007 and Indonesia was its second largest exporter, accounting for about 30 M tons (12% of the total imported coal). Indonesia produced about 200 M tons of coal, about 75% of which was exported in 2007. As the Indonesian government has decided on an energy policy wherein 33% of the country?s primary energy demand will be met by coal by the year 2025, the domestic demand for coal has increased dramatically in recent years. Over 99% of the coal produced in Indonesia comes from surface mines. However, the conditions of surface mines are worsening each year: the stripping ratio is increasing, approaching the economic ratio, and the infrastructure for coal from inland mining areas is insufficient for such intense mining operations. To meet the demand for coal in Indonesia and the rest of the world, underground mines have to be developed. However, mining engineers and/or miners in Indonesia do not have a lot of experiences, expertise and know-how concerning the plans and operations of an underground coal mine. In addition, the industry faces a lot of problems which include poor conditions such as a steep coal seam, groundwater problem, stability of highwall, etc. Under these situations, a mine targeted in this research attempts to develop a new underground mine from an open-cut highwall because the stripping ratio in the surface mining area has almost reached the limitation of economic value. This paper discusses the possible development of a new underground coal mine from an open-cut highwall by means of field observation and numerical analysis.

Jan 1, 2009

By D. A. Norrgran

The recent development of rare earth permanent magnets has revolutionized the field of magnetic separation. The advent of rare earth permanent magnets in the 1980's provided a magnetic energy product an order of magnitude greater than that of conventional ferrite magnets. This has allowed the design of high-intensity magnetic circuits operating energy free and surpassing the strength and effectiveness of electromagnets. New applications and design concepts focused on the mineral and metal processing industries have evolved. This technology also led to the development of various magnetic separators specifically designed for mineral processing applications. Applications which were not previously considered are now being applied to primary mineral upgrading and recycling and secondary recovery.

Jan 1, 1993