Search Documents

By Roussos Dimitrakopoulos, Liam Findlay

Semimobile in-pit crushing and conveying (IPCC) systems can help reduce truck haulage in openpit mines by bringing the crusher closer to the excavation areas. Optimizing a production schedule with semimobile IPCC requires integrating extraction sequence, destination policy, crusher relocation, conveyor layout and truck fleet investment decisions. A mining complex with multiple mines and IPCC systems should be optimized simultaneously to find an optimal schedule for the entire value chain. An integrated stochastic optimization framework is proposed to produce long-term production schedules for mining complexes using multiple semimobile IPCC systems. The optimization model has flexibility to select the crusher locations and conveyor routes from anywhere inside the pits. The framework uses simulated orebody realizations to consider multielement grade uncertainty and manage associated risk. A hybrid metaheuristic solution approach based on simulated annealing and evolutionary algorithms is implemented. The method is demonstrated using an iron ore mining complex

Nov 1, 2024

By Joseph M. Chelini

Today, the two major operating costs of rubber tired off-road equipment are diesel fuel and tires. Mine Management has minimal control over the ever accelerating diesel fuel costs. However, they can exercise control over abnormal tire costs. Fortunately, with available technology and cost analysis methods, experience shows us the outlook for controlling tire costs is encouraging. Most earthmoving operations using off-road, rubber tired haulage and support equipment have abnormally high total tire costs. These costs, utilizing Tire Information Management, have been reduced more than 30%; 20% can often be guaranteed. Management Apathy on the subject of tires in a complex mining operation perhaps can be understood, but management apathy applied to an abnormally high operating cost, of which tires are, begs for a solution.' Tires have been professionally neglected for many years in most mine operations. This is exemplified in the January, 1982 issue of Mining Engineering by Charlie Son in his article Reducing Earthmoving Tire Costs. He compared the efforts to improve diesel engine costs to the same efforts given to earthmover tires.

Jan 1, 1983

By William E. Foreman

Editor's Note: For purposes of uniformity throughout this book, Coal Preparation, 5th Edition, the editors have advocated the use of the U.S.A. Sieve Series of testing sieves (see Table 6-2) as the testing sieves of modem choice. The adoption and use of the U.S.A. Sieve Series and its forerunner, the Tyler Standard Screen Scale, has for over seventy-five years introduced uniformity into reports; has simplified the comparison of results; and has provided control for operation of modem coal preparation circuits. While a full explanation of the differences, and more importantly the similarities of these two measuring systems cannot be stated here, it is felt that a brief clarification of terms is in order. The difference between the U.S.A. Sieve Series and the Tyler Standard Screen Scale Sieve Series is the identification method. Tyler Screen Scale sieves are identified by mesh designation with the width of opening varying by the square root of two, or 1.414 times the width of opening in the previous sieve. The U.S.A. Sieves are identified by openings in millimeters or microns and also arbitrary numbers which do not necessarily mean the mesh count; this series uses width of opening variations in the order of approximately the ratio of the fourth root of two, or 1.189. Tyler Standard Screen Scale and U.S.A. Sieves can be used interchangeably, and to avoid confusion the nameplate of all Tyler Screen Scale sieves show the U.S.A. Number, while all U.S.A. Sieves show Tyler Screen Scale mesh equivalent numbers on the nameplate. INTRODUCTION Sizing is the process of separating mixed mineral particles into groups of particles all of the same size, or into groups in which all particles range between definite maximum and minimum sizes. This chapter applies the modem mechanical screen and the liquid-solid cyclone (hydrocyclone) to the process of sizing solid particles as applied to coal preparation. Screening is a mechanical process that separates particles by size. Modem coal preparation is made possible by efficient sizing. Sizing of coal is defined in terms of the opening through which an individual particle will or will not pass, or as two openings, the larger of which passes the particle and the smaller of which retains the particle. Screening accomplishes sizing by passing coal of a wide range of sizes through a series of screens, each of a decreasing size. The individual screen discharges are then directed into different screen products for subsequent sale or processing. Screening in modem preparation plants is done for the following reasons: 1. Removal of fine coal before a size reduction step. 2. Size separation of the coal into a coarse and fine fraction for sized products or for processing in coarse and fine coal circuits. 3. Recovery of heavy media from heavy media coal cleaning circuits.

Jan 1, 1991

By V. R. Degner

The minerals industry trend toward very flotation machines, exceeding 10 m3, began in the late 1960's and responds to the continuing desire to achieve better plant economics through improved plant floor-space utilization, power requirements, and operational /maintenance manpower heeds. In general, as process design tonnage increases, the benefits of the larger flotation machine becomes more evident. The development of the larger flotation machine can be distingushed from earlier, smaller, machines in demanding a rational "scale-up" procedure to guide the basic design, thereby producing a machine prototype capable of satisfactory-operational evaluation at minimum cost. Proven flotation machine "hydrodynamic" scale-up consideration, successfully applied in the development of both the WEMCO No. 164 (28.3 m3) and No. 190 (42.5 m3) machine will be reviewed, and the resulting economic benefits of large flotation machines in high tonnage applications will be summarized.

Jan 1, 1985

By J. L. Sloughfy

The size distribution and mechanical strength of the iron ore pellet burden are important parameters in determining the efficiency of the blast furnace. From the very outset, the guiding principle of our pellet quality improvement program was that these parameters are also the key to improving productivity and cost control at the pellet plant. Recognizing the need for improved blast furnace burdens and for higher productivity and lower costs at the pellet plant, Carol Lake operators, in conjunction with the IOC Pellet Quality Committee, established the following goals for the improvement of Carol pellets: [ ]

Jan 1, 1981

By S. Chander

A review of the published literature on the mechanism of depression of sulfide minerals shows that a unified theory is not yet available. The various mechanisms that have been postulated include competition between depressants and collectors to adsorb at the surface sites, creation of thermodynamic conditions nonconducive for formation of a metal collector salt or formation of a hydrophilic coating on the surface. The hydrophilic coating may or matt not effect the adsorption of collectors. In yet another mechanism, the depressant nay participate directly in oxidation/reduction reactions between collectors and sulfide minerals. Examples from the literature are discussed to highlight oxidation/reduction effects in the depression of sulfide minerals.

Jan 1, 1984

By Robin J. Hickson

The Ortiz Mine is operated by Gold Fields Mining Corporation, a subsidiary of Consolidated Gold Fields Ltd., one of the world's major gold producers. The Ortiz Mine is Gold Fields only heap leaching facility as well as being their first operating mine in the U.S.A. The hydrometallurgical processes utilized for recovery of gold and silver at Ortiz are discussed along with the several practical changes in operation adopted since start-up. Included are heap leaching by cyanidation, concentration of values on activated carbon, desorption, and the final electrowinning steps prior to shipment. Construction costs and pertinent technical data are shown.

Jan 1, 1981

By Nathaniel Wollman

About nine years ago the President's Materials Policy Co commission under the chairmanship of William Paley released its report entitled "Resources for Freedom." Not long ago the Senate Select Committee on National Water Resources under the chairmanship of Senator Kerr released a study entitled Water Supply and Demand. Both reports contained projections of future water user the report for 1975, and the Select Committee print for 1980 and 2000, It is my task to compare the two reports. In the initial letter from Mr. Kazmann arranging for thus session he suggested that I present "a critical evaluation of the Paley Report's section on water ?ten years later,? which might include a comparison of predicted and actual water-use rates and would spotlight the assumptions which lead to errors in the predictions , . ." It is possible to compare the results of both studies, and it possible to explain art of the differences that can be found between them. The remainder must remain shrouded in doubt, since the Paley Report did not give all details of the methods used in estimating the com¬ponents of water use.

Jan 1, 1961

By Missy Isaman

"Mixed ground tunnels come in all kinds. In rock tunnels with possible faults and high pressure water, the challenges are many. With the advent of Crossover TBMs, contractors can minimize machine wear in such conditions while maximizing efficiency. The newest generation of Crossover is exemplified by two projects in Albania and Turkey. A 5.56 m Crossover TBM destined for Turkey’s Gerede Water Transmission will be assembled using Onsite First Time Assembly (OFTA) from within an existing tunnel. The unique machine will bore through 30 fault zones requiring the TBM to be sealable to up to 20 bar so pre-consolidation grouting can be done. If boring under pressure is required, the TBM will bore sequentially using the screw conveyor fore and aft gates. Skewing further towards hard rock, a unique 6.2 m diameter Double Shield TBM with Crossover features was designed for Albania’s Moglicë Headrace Tunnel. The machine features closure doors and a sealing system to contain inrushes of water until they can be grouted off. This paper will discuss the unique aspects of the Crossover designs, including their inception as based on past projects in difficult ground, and their utilization at the two current projects. INTRODUCTION Specialized tunnel boring machines have been made for years to tackle specific types of ground conditions. Traditional types of TBMs bore within a specific set of ground conditions. If a project is located in a competent granite face, then a Main Beam machine is a good solution. In soft ground, Earth Pressure Balance (EPB) machines are the method of choice. Years of experience and engineering advancements have made both types of machines fast and economical solutions for tunneling. Unfortunately not all ground conditions are a perfect swath of one material, and the need for a more diverse machine is apparent."

Jan 1, 2016

By T. W. Peterson

There are two approaches to developing a minicomputer based application for an industrial grinding circuit. Usually, the control program is coded and compilation-debugged on a large-scale scientific computing system or the minicomputer itself if the machine is available. Final debugging and testing must wait for installation and checkout of the entire minicomputer system. Two immediate disadvantages of this approach are the need to obtain, install and check out the hardware before the final debugging stages of program development can begin, and interference with normal mill operation during such final testing. This work reports on an alternative to the usual procedure. Here both compilation and execution bugs are eliminated from the application program before hardware installation by testing the control program against a reasonable dynamic simulation of the entire process. Thus, software development can be completed before the target mini is installed. Such off-line development requires a reasonably accurate mathematical model for the entire process system as well as a suitable simulation package for communication between the simulated environment and the minicomputer application program. Specific data describing the design configurations and dimensions of the mills, cyclones, sumps, pump characteristics and analog controller configuration were supplied by ANAMAX for a grinding division consisting of a rod mill followed by two ball mills in parallel. This information was used to set up a plausible model structure. Steady state ANAMAX data on particle size analysis at various points in the circuit and corresponding values of flow rates, pump speeds, sump heights and slurry densities were used for model parameterization. The preferred operating control strategy - "best grind at operator-set rod mill feed rate" - was set by ANAMAX. An inferential particle size analysis technique using the cyclone cluster as an on-line particle size sensor was used in a novel control strategy_ to achieve the stated objective. Two disturbances common in the ANAMAX circuits - rod mill scoop pluggage and shut down/start up of one of the ball mills - were studied in detail. This report out- lines the steps in system development and testing and the results obtained.

Jan 1, 1974

By Kevin Sierra, Orfelinda Avalo, Julio Guizado, Edwilde Yoplac, David Martinez

Mining tailings are slurry byproducts of mineral recovery. They generate serious environmental risks due to their toxicity when exposed to water and oxygen. Studies focus on eco-friendly alternatives for mitigating these environmental impacts. Processing these tailings enables a sustainable mineral production model through circular economy practices. This study evaluates using gold mining tailings to recover gold and produce bricks. Flotation tests obtained a concentrate with 86.66% gold recovery, containing sulfides (pyrite, arsenopyrite) and a tailing with silicates and oxides suitable for brick manufacturing and ornamental pieces. This approach promotes eco-friendly solutions and a greener approach to mining operations.

Feb 1, 2024

By N. L. Wesis

General History The first jaw crusher in the US was patented about 1830, but the Blake crusher that has maintained a substantial advantage over other types was invented in 1858 by Eli Whitney Blake. For going on 150 years the jaw crusher has been an invaluable machine; even today, when gyratory crushers have assumed most of the burden of crushing large tonnages of large rock and ore, the jaw crusher has a firm place in the mining industry. It is interesting that soon after the invention of the Philetius Gates gyratory crusher in 1881, a contest between the first No. 2 Gates and Blake jaw crushers of equal gape showed the gyratory to be 3.2 times as fast. This foretold a day not far in the future when the jaw crusher would not be adequate on the largest jobs. In his Textbook of Ore Dressing (1909) R. H. Richards recom¬mended that the word breaker be used for all machines breaking to relatively large sizes (say to 5 in. or greater), and crusher be used for finer work. Even in the 1968 US Bureau of Mines dictionary of mining terms the work breaker is defined by Richards in this context. However, in modern US usage it is nearly limited to coal breaking. Over the years the jaw crusher has been developed in a variety of forms but it appears today in these three general forms: (I) Blake type, (2) Dodge type, and (3) single toggle (or overhead eccentric) type. All of these crushers have a fixed jaw and a moving jaw, between which the coarse rock fragments are intermittently caught and crushed. The three types are differentiated by the manner in which the movable jaw is moved in relation to the fixed. Types The Blake-type crusher is shown in cross section in Fig. 1. The simplicity and strength that have made it first among jaw crushers are evident. The movable jaw is suspended from a cross-shaft at its upper end, this shaft being carried in bearings on the sides of the frame. The actuating mechanism consists of an eccentric shaft, also supported in frame-mounted bearings, which imparts through a pit¬ man and a pair of toggles a reciprocating motion to the bottom of the swing jaw, the return movement being effected by several spring¬loaded rods. The whole is built into a box frame with the crushing chamber at one end. As in all jaw crushers, the eccentric shaft is equipped with a heavy flywheel that maintains an even speed through¬out each stroke. The Dodge-type crusher illustrated in Fig. 2 is simple, mechani¬cally. Its movable jaw, being pivoted below the discharge opening, has minimum movement at crusher discharge and maximum at crusher feed. Because the choke point coincides with the point of least motion, these crushers are of relatively low capacity, and the rapid action in the feed area gives the machine the advantages of large reduction ratio and closely sized product. Thus, it fits well into low-capacity operations like sample reduction. Besides low capacity, its principal disadvantages are tendency to pack and make fines. The single-toggle or overhead-eccentric type of jaw crusher (see Fig. 3) has gained in usage, starting as a modification of the Dodge idea in that the greatest movement of the movable jaw occurs at the top, and being gradually improved and strengthened to its position today where it covers just as wide a field of application as the Blake type from the standpoint of feed opening. The motion of the movable jaw is the result of the circular motion of the eccentric shaft at the top of the swing jaw combined with the rocking action imparted to the bottom by the inclined toggle plate. Because of light weight and mechanical simplicity, it is economical in small mills and portable plants where the rock is not as tough and abrasive as to punish the machine with excessive impact from shocks, or excessive wear result¬ing from the pronounced vertical component of motion.

Jan 1, 1985

By Stephen M. Voynick

Two hours driving time west of Denver, CO and 21 km (13 miles) north of Leadville, Bartlett Mountain rises 4,065 m (13,337 ft) high in central Colorado's Tenmile Range. Bartlett Mountain is one of Colorado's most recognizable peaks, especially when the late afternoon sun casts a surreal, reddish light across its most prominent feature - the Glory Hole. This is a gaping, half-mile-wide, 245-m- (800-ft-) deep crater. Created by subsidence from 60 years of massive underground mining, the Glory Hole is a monument to the Climax Mine, one of the great achievements in American mining and metallurgy. For most of this century, the name Climax has been synonymous with brilliant mining engineering, innovative metallurgical research and entrepreneurial promotion of a once-obscure metal - molybdenum. Climax overcame an array of economic, technological and social problems to become a model for underground development of massive deposits of low-grade ores. It is one of the few mines in the world where cumulative production is measured in the billions of dollars. The Climax mineralization was emplaced 30 million years ago. Magmatic intrusions formed a large, mineralized stockwork within the granite country rock of Bartlett Mountain. Associated hydrothermal events forced superheated metal- and quartz-rich solutions through fracture zones, silicifying the country rock and depositing huge amounts of molybdenite, or molybdenum disulfide. The mineralized rock, a light gray, finely crystalline, silicified granite, is laced throughout with blue-gray quartz veinlets containing molybdenite. Although the richest ores graded only about 1% molybdenite, the Bartlett Mountain deposit contained more than 2.7 Mt (3 million st) of elemental mo- lybdenum.

Jan 1, 1997

By V. Canby

Introduction Located in Russia’s Chukotka Autonomous Region near the Arctic circle and 425km from the seasonal port of Pevek (population approximately 4600), Peschanka (or ‘Anyui’) is perhaps the world’s most isolated CuMoAu porphyry deposit of significant grade and tonnage. In addition to its extreme remoteness (66°36'N/164°30'E) and lack of developed infrastructure, Peschanka is located in one of the world’s coldest regions, with annual average temperatures well below freezing. Soviet exploration up to 1985 defined four zones with inferred resources of roughly 940Mt @ 0.51% Cu, 0.42 g/t Au, 1.4 g/t Ag and 0.019% Mo (1).

Jan 1, 2007

By D. Zaharaki

In the present experimental study the geochemical stability of inorganic polymers was studied by immersing them in various solutions (distilled water, seawater and 0.5N HCl) for a period of 7 months. Inorganic polymers were synthesised by mixing ferronickel slag with kaolinite, potassium hydroxide and sodium silicate solution. The cement like paste was heated at 80 °C for 48 hours and left for curing at room temperature. Their structural integrity was assessed by compressive strength testing after subjection to freeze-thaw cycles as well as high temperature heating. XRD studies were carried out in order to identify new formed phases and provide useful information regarding the progress of the mechanisms involved.

Jan 1, 2008

By J. B. Knapp, J. W. G. Betts, Scott L. Burreill, J. H. Bassarear, E. A. Lowe, W. J. N. Davis, John L. Bolles, Gaylord P. Dopson, William H. Keener, N. S. L. Steenkamp

This chapter contains moderately detailed descriptions of some typical and well known mills that treat predominantly sulfide copper ores, some containing secondary values in gold, silver, and molybdenum. The descriptions are general in nature, because most of the specific data will be found in tabulations elsewhere in this section, covering a large number of mills in such matters as flotation reagents, crushing and grinding equipment and steel consumption, thickener and filter operating data, power consumption, and many others, in a manner that the reader will find convenient and comprehensive for reference and comparison. On the other hand, the plant descriptions selected for this chapter emphasize the kind of information that cannot be readily tabulated.

Jan 1, 1985

By Ian Graham

In 2013 the Government of New Zealand launched a number of ‘National Science Challenges’ (NSC) to address major issues facing the nation, and raise public consciousness about science and its role in promoting evidence-based decision making. One of the 10 proposed NSCs focuses on New Zealand’s extensive Exclusive Economic Zone (EEZ) and Extended Continental Shelf (ECS)1, with an objective to enhance utilisation of marine resources within environmental and biological constraints, and the desired outcome of:

Sep 1, 2014

By Y. Nakahiro, T. Wakamatsu, M. S. Elsalmawy

The flotation of quartz, feldspar and alumina was studied as a function of pH when using N-alkyldiamines as collectors. The lengths of alkyl chains of diamines were 8, 9, 10, and 12 carbon atoms. It was found that shorter hydrocarbon chain length of alkyldiamines has stronger tendency to float quartz while the feldspar responded poorly to flotation with these collectors at high pH values. The effect of addition of nonionic surfactant of Brij type, when using dodecadiamine as collector, was investigated. Flotation studies in the absence and in the presence of sodium dodecylsulfonate were carried out. These studies have indicated that sodium dodecylsulfonate, in the concentration studied, functions as strong depressant for feldspar.

Jan 1, 1995

By Shuang Shuang Huang, John Fillos

Ozonation was evaluated as an alternative treatment process for leachates of municipal landfills. The study was carried out on leachate from the Fresh Kills Landfill, New York City. The leachate has strong tea color and BOD5 ranging between 90 mg/L and 130 mg/L. The average COD, TOC and NH3-N concentrations were 1800 mg/L , 550 mg/L, and 665 mg/L, respectively. The kinetics of the process were studied in a sparged batch reactor by developing concentration- time profiles for residual color and TOC. Continuous flow experiments were then carried out at two selected contact times. The process was found to be effective in the treatment of leachates for color and TOC removal.

Jan 1, 1992

By F. Sachanidis

The lignite surface mines of Ptolemais basin operate according to special environmental terms regarding the concentrations of heavy metals and trace elements in water discharges. Based ?n the results of lab analyses and in-situ measurements conducted so far it is concluded that the concentrations of heavy - toxic metals and other trace elements are low or negligible. The deviations from the upper concentration limits specified by laws and regulations are rare and non-systematic both on their spatial or temporal distribution. The same results prove also the relation between water quality and type and nature of the sediments forming the Ptolemais basin and the carbonated and metamorphic rocks forming the surrounding mountain areas.

Jan 1, 2006