Search Documents

By George J. Simchuk

The selection of a stripping method and subsequently, the stripping equipment, are two of the most important decisions confronting a project engineering staff during the initial feasibility study of a new coal stripping operation. The selected stripping units average from 60 to 70 percent of the total capital outlay for mine equipment and their selection will affect the type, size, and quantity of the attendant equipment, such as loading shovels, drills, haulage trucks, and bulldozers. This paper is intended to report on an in depth study by Utah's Technical Services Staff regarding the selection of stripping equipment for the Goonyella Coal Mine in Queensland, Australia. We will touch briefly, on the objectives considered in this selection; the various alternatives which were explored; the general assumptions that were followed throughout the engineering and design of an appropriate stripping system; and computations necessary to determine the amount and size of stripping equipment. INITIAL EXPLORATION Utah Development Company (presently 90% owned by Utah Construction & Mining Co. and 10% by Australian investors) commenced systematic geological studies of the Bowen Basin coal fields of Central Queensland in 1961. The Blackwater Mine as shown in Figure 1 has since been established in this area and is now producing 3.0 million tons per annum of washed coking coal. Geological reconnaissance was then extended to the northern part of the Bowen Basin and in 1963 Utah's coal prospecting area covered 2444 square miles of Central Queensland. The authority to prospect north of Blackwater has since been trimmed to 810 square miles by relinquishments to the State.

Jan 1, 1971

By C. L. Jiang

The selective depression of pyrite obtained from Kentucky No.9 seam in coal flotation with various kinds of inorganic and organic chemicals was systematically examined. Most of the organic chemicals tested showed little selectivity in pyrite depression. It was found that both orthophosphate and pyrophosphate were effective for the selective depression of coal pyrite in coal flotation using fuel oil as a collector. At substantially low concentrations of pyrophosphate, the flotation of coal pyrite was completely depressed over a wide pH range, while the coal flotation remained unaffected. The mechanism of the selective depression of pyrite by phosphates has been explained with the help of thermodynamic calculations of iron-phosphate-water systems and zeta potential measurements. It was shown that pyrophosphate reacts strongly with iron ions of pyrite to form stable hydrophilic iron pyrophosphate complexes on pyrite surfaces.

Jan 1, 1998

By William Gleason

"On April 4, 2017, the largest earth-pressure-balance tunnel boring machine (TBM) ever built finally completed its 2.7-km (1.7-mile) journey beneath Seattle, WA, nearly four years after it began boring the SR-99 tunnel that will eventually replace Seattle’s Alaskan Way Viaduct.By now, readers of this publication are familiar with the ordeal that began on Dec. 6, 2016, when the machine overheated and shut down. Until that point, the TBM, named Bertha, had grabbed headlines for being the largest in the world with a 17-m (57.6-ft) diameter face. But after the incident that stopped the progress, the headlines suddenly stopped focusing on the engineering marvel of the tunnel project and began asking what went wrong. Just 300 m (1,000 ft) into the tunneling journey the machine was stuck, unable to move forward and impossible to retract.The project’s contractors, Seattle Tunnel Partners,(STP JV) – a design-build consortium comprised of Dragados - USA, Tutor Perini, say a 20-cm (8-in.) steel well-casing buried in the path of the machine caused the problems that halted the TBM. The Washington State Department of Transportation (WSDOT) disagrees, and the issue over who ultimately pays for the repairs is now with the courts.Eventually, engineers determined the best way to get Bertha back to work was to dig a 36-m (120-ft), deep concrete lined shaft pit in front of the machine and lift the 1.8-kt (2,000-st) cutterhead out for repairs. The repairs took two years but eventually the machine resumed mining in January 2016. In April 2017, the TBM finished building the tunnel, breaking through at the tunnel’s north end near Seattle’s Space Needle, with little to no ground surface movement measured on the entire alignment.While the cause of the TBM breakdown and who should pay for repairs was debated above ground, the work below ground continued. David Sowers, deputy program administrator, engineering and program management with WSDOT, told Mining Engineering during the 2017 Cutting Edge Conference in Seattle that in addition to the technical marvel that the tunnel became, the fact the parties involved were able to work through the unprecedented challenge is a great example of how to overcome challenges on massive projects."

Jan 12, 2017

By George E. Aikens

Prolonged subzero climatic conditions impose some unique engineering problems for the developer and operator of open-pit mines in the Far North. The remoteness of the job site and the extremely cold, long, dark winters severely tax both man and machine in the quest for the Arctic's rich mineral wealth. Undoubtedly the singular most troublesome problem for the engineer is Permafrost which underlies about 201o of the land area of the world and about 85% of the state of Alaska. Permafrost has its impact on building construction and mine excavation, while posing a more pervasive threat to the-delicate ecologic balance within the Arctic wilderness. Yet the difficulties associated with mining up North may not be as overwhelming as has been previously supposed. For example, the lowest temperature recorded at Point Barrow is -560F, whereas Montana has recorded -69.7° F.. There are no specially designed machines for mining and construction in the Arctic, and efficient equipment utilization is maintained through proper operation and servicing techniques. However, neither equipment or people can be assumed to function normally at -40°F. Special techniques in drilling, blasting, and ripping are being used to yield economically competitive ores. Overall, a fundamental understanding of the nature of Permafrost will allow the engineer to deal expeditiously with an Arctic mining venture and at the same time to deal fairly with Arctic environment.

Jan 1, 1972

By C. W. Schultz

The distribution of material passing a screen, or a set of screens, is described by the equation [ ] where p = the probability that a single particle will pass the screen on a single presentation k = number of layers of screen cloth n = distance from head of screen expressed as number of screen openings. This model can be used to predict the performance of conventional screening operations (i.e., k = 1) as well as the so-called "statistical screening" operations. Using this technique, in which multiple identical layers of screen cloth are employed, screening can be carried out at a finer size than is possible with conventional techniques with no loss of separation efficiency.

Jan 1, 1969

By J. Reyher, R. Bratton, G. Luttrell, B. Li

"Flotation is regarded as the best available method of upgrading minerals and coal fines. However, its efficiency deteriorates rapidly with decreasing particle size. Further, ultrafine concentrates are difficult to be dewatered economically, forcing companies to discard part of the ultrafine materials to impoundments. To overcome these problems, a new method of separating and simultaneously dewatering ultrafine particles has been developed. Following extensive laboratory-scale test work, the process, known as hydrophobic-hydrophilic separation (HHS), has been tested successfully in continuous operations at proof-of-concept (POC)- and pilot-scale tests. The results show that the HHS process is capable of producing high quality clean coal with high recoveries and low moistures. INTRODUCTION Coal preparation plants are designed with up to four parallel processing circuits for treating coarse (> 12 mm), intermediate (12x1 mm) small (1x0.15 mm), and fine (<0.15 mm) particles. The plus 0.15 mm fractions can be effectively cleaned efficiently with gravity separation methods (Wills, 2006). At present, the only commercially viable option for cleaning the finest fraction is froth flotation (Yoon et al., 1999). In flotation, air is dispersed in the form of small air bubbles in a tank in which coal fines are suspended. The small air bubbles selectively collect the hydrophobic coal particles and float to the surface, forming a froth phase which overflows into a launder. As is well known, ultrafine coal particles of less than 30-50 µm are difficult to be collected by the air bubbles, resulting in low recoveries. Furthermore, fine particle flotation suffers from low carrying capacities and poor selectivity due to entrainment problems. (Bethell et al., 2005; Luttrell et al., 2014). In addition, the froth products containing ultrafine coal are difficult to dewater. Mechanical dewatering in general becomes inefficient with decreasing particle size due to small cake porosity and high surface area, resulting in high moistures (Hucko et al., 1988). The cost often becomes prohibitive with particles of smaller than ~45 µm (Bethell et al., 2005). Moreover, the high-moisture products are difficult to handle and incur high shipping costs and lower thermal efficiencies (Honaker et al., 2013)"

Jan 1, 2016

By Anil K. Ray

Roof falls are one of the greatest hazards in underground coal mines worldwide. Due to stringent safety measures and extensive support system development, roof falls have been reduced significantly but they still persist in many underground coal mines. Some of the roof falls initiate with cutter roof or guttering. In the past, many factors have been identified as being responsible for the development of cutters and roof fall. These responsible factors can be broadly classified as stress related or non-stress related. In this paper the finer details of mining technique have been taken into consideration for better understanding of cutter roof and roof fall problems. Three dimensional finite difference modeling has been used to explain the mechanism of cutter development. Strain softening material behavior has been used to realistically simulate the cutter formation, and common cutting sequences as implemented in the field have been simulated. This was done with an objective to determine whether the cutting sequence has really any significant control over cutter formation or not. In addition to cutting sequences, the effect of cut length is also studied. The effect of step cutting and turning of crosscut into and away from major and minor horizontal stresses is also examined to see its influence on cutter development.

Jan 1, 2009

By Jon Bowler

Daw Mill Colliery, UK Coal, near Coventry in England, mines the Warwickshire Thick Seam at 800 m/2500 ft depth using longwall retreat with gateroads supported by rockbolts. Over the last eight years the mine has worked longer and wider panels with extraction heights of over 5 m. Recently the mine has experienced high deformation conditions principally from the rib sides resulting in operational issues and production delays. Investigation of rib deformation was undertaken using new inspection and measurement techniques, including systematic laser surveying, and improved rib support consumables were developed and introduced. A new rib trussing system using textile webbing has proved very successful.. A rib support management system was also developed and introduced for face retreat. This allowed rib support to be more effectively managed both for production and safety. For the current developments, new 28-mm-diameter roof and rib bolt systems have been introduced and rib bolt length has been increased to 3 m, with the aim of achieving gateroad stability over the life of the panel. Significant reductions in roof and rib deformation have been confirmed by the latest monitoring results. These ground control innovations are allowing Daw Mill?s potential to be realised. Production from 302?s face in 2008 set new UK and European records. However the support enhancement process continues and further innovations are planned.

Jan 1, 2009

By E. J. Haas

DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the views of the National Institute for Occupational Safety and Health. Reference to specific brand names does not imply endorsement by the National Institute for Occupational Safety and Health. ABSTRACT Leadership is a critical component to an organization’s safety culture and influences the ways that health and safety is enacted on site. Therefore, it is not surprising that improving leadership will also improve safety. Worker perceptions of management practices are shaped through unique leader-employee interactions over time. However, few details are known about the communicative support (i.e., emotional, informational, and tangible) offered by supervisors and its impact on miners’ perceptions and performance. Using pre and post-interview data with 20 supervisors and 48 workers during six-week interventions, researchers identified positive and negative instances of supervisor support and its implications on worker performance. This paper highlights the common support tactics offered by supervisors and desired by workers to help practitioners identify ways to improve their safety culture and subsequently, the proactivity and compliance of their workforce. INTRODUCTION Supervisory leadership is a critical component to the effective implementation of an organization’s health and safety management system (HSMS). Specifically, supervisors serve as representatives of an organization and their actions are indicative of the organization’s safety culture (Eisenberger et al. 1986). Senior management has been shown to serve as a frame of reference for guiding safe behaviors in the workplace (Mearns et al. 1998) and, more recently, research has related supervisory enforcement to workers’ safety compliance (Petitta et al., 2017). Therefore, it is not surprising that by improving leadership, perceptions of management and subsequent safety outcomes are likely to improve as well (Zohar, 2002). Perceptions of management are shaped through unique leader-employee interactions over a period of time (Hofmann and Morgeson, 2004, 1999). How these unique interactions impact worker performance, however, remains unexamined. As a result, understanding how supervisor-employee relationships operate in high-risk environments is unclear (Mirza and Isha, 2017; Denis et al., 2010). A starting point to better recognize the idiosyncrasies of these relationships is by way of examining the communicative support offered by front-line management and received by industry workers. To this end, this paper uses pre- and post-interview data to study the communicative aspects of supervisor-employee interactions at mine sites. The analysis uses a social support framework to identify positive and negative instances of supportive communication. From interview data with 20 managers and 48 mineworkers, data emerged that shows how supervisors’ unique types of support contribute to workers’ perceptions, motivation, and follow-through of safe work behavior.

Jan 1, 2019

By Tom Skodack

Mine and tunnel contractors face a complex environment-one in which economic risks are high, operating costs grow ever higher, ore grades are lower or recovery more difficult, and civil construction projects are intensely competitive on a world-wide scale. Within the context of this environment, the risks and rewards of proper machine selection for rock excavation have become proportionately large. Speed, depth and scope of analysis, and extensive supporting information are indispensable in the selection process. Equipment designs and their applications are also myriad and diverse. Several equipment alternatives and excavation techniques may have to be evaluated at once to choose the most cost-efficient approach. The following examples are typical of the current demand for more detailed equipment analysis: • An aggregate supplier starts a new quarry. He knows his targeted tonnage, blasting restrictions, and previous operating costs from other quarries. But he must improve on his old costs. What drill pattern, hole size, and bench height will give lowest cost per ton? How many crawler drills and what type will produce this tonnage most efficiently? • A mine is using a fleet of twin pneumatic ring drills for long hole drilling to initiate their cave. The mine is facing both air shortages and increasing operating costs with decreased efficiency in the ring drill fleet. If they invest in new hydraulic long hole drills, what impact will each drill unit have on production? Each twin drill unit? What configuration gives best operator efficiency and subsequent reduction in manpower? Which configuration gives the best return on investment? • A tunnel contractor is bidding a long straight water tunnel by conventional drill and blast methods. What is the optimum number of drill booms for the tunnel cross section and excavation schedule? How many rounds per day can he achieve? What are his total project drill, blast, and muck costs? In the past, such questions could be answered, but only approximately at best. One good prediction could involve many hours of laborious calculations that had to be repeated each time a new parameter was introduced or an existing parameter changed. In 1980, increasingly complex analysis, coupled with increasing need and quick response times demanded by industry, led Atlas Copco&apos;s project department to turn to the computer. New computer programs based on theoretical considerations and three decades of worksite performance data were developed for evaluating mine and tunnel contractors&apos; equipment needs, productivity, and partial or total operating cost calculations for most conventional drill and blast excavation techniques-including shot rock loading and transportation. This Computerized Analysis of Rock Excavation-or CARE-program has since been available to the mining and construction industry. From each program specific results can be pre- dicted, including: • Productivity Calculations-Rock drill penetration rate for a given drill, hole size, and rock type, optimized for the best drill steel life; net machine productivity (drill-out time or drill meters-footage-per shift); total drill round time, including charging, blasting, loading, and haulage; suggested drill pattern, computer printed, including hole size for a given rock drill, rock type, and associated blasting restrictions for either drift rounds or benching applications; long-hole drill meters (ft) per drill shift; breasting down (upper drilling) drill meters (ft) per drill shift; and comparison between continuous loading machine capacity and LHD capacity. • Operating Cost Calculations-Operating costs expressed as cost per drill meter (ft), cost per cubic meter (cubic yard) of excavated rock, and cost per meter (ft) of tunnel advance. These costs may be calculated using as many cost centers as the mine, quarry, or tunneling contractor wishes. Specific operating costs may cover drill rig operating costs only, less capitalization; drill rig operating costs, including amortized equipment investment; drilling and blasting costs; drill, blast, load, and haulage operating costs; long-hole drilling operating costs per drill meter (ft) or per blasted cubic meter (cubic yard) of rock; and loading and transport operating costs. In all the above cases, any number of cost and capacity calculations may be run by simply changing important cost center variables to judge their net effect. Accuracy as a Function of Input Data and the Statistical Data Base Accuracy of a projection clearly depends heavily on the data base from which the projection is drawn.

Jan 11, 1982

By J. D. Miller, C. L. Lin, J. Dong

Nano clay mineral particles such as kaolinite — with primary particles typically smaller than 2 μm in size — can cause significant problems in flotation processes and tailings disposal, including the processing of Florida phosphate rock and Canadian oil sands. In this study, the consolidated state of flocculated kaolinite sediment was examined, and high-resolution X-ray microtomography (HRXMT) was applied to describe the structure of the consolidated sediment. Using this tomographic information, the complex geometry of the channel network structure for the consolidated flocs was established for the first time. With the establishment of the experimental channel network structure, permeabilities were estimated by flow simulation using the Lattice Boltzmann method. Results for kaolinite sediment with and without polymer are compared and discussed. Results for flocculated kaolinite sediment in a gravitational field are also presented and discussed. The results show that as polymer dosage increases, the permeability of flocculated kaolinite sediment increases, and as suspension pH increases, the permeability of flocculated kaolinite sediment decreases.

By K. A. Natarajan

Platinum electrodes are not inert as originally thought to be. The reactivity of platinum electrodes can explain their erratic behavior in many electrochemical measurements of metallurgical interest, e.g., in flotation systems, streaming potential measurements, contact-angle measurements, and in leaching systems. The anomalous behavior of platinum electrodes in redox potential measurements in aqueous systems was studied through Eh and pH measurements in water-oxygen, iron-water-oxygen and manganese-water-oxygen systems. Stability relations between Fe++ and Fe(OH)3 and between Fe(OH)2 and Fe(OH)3 were studied to judge the correspondence between experimental and theoretical equilibrium lines. The practicality of redox potential measurements in estimating ferric-ferrous ratios in aqueous systems was investigated along with their suitability as indicators in leaching operations, e.g., the removal of iron by aeration from manganese leach solutions.

Jan 1, 1970

By M. J. Hart

There are no formulas that guarantee success when it comes to obtaining zoning approval for mineral aggregate mining. Local land use decisions often times represent the most controversial issues faced by community. Public awareness, concern, willingness to get involved, sensitivity to the environment and probably most importantly fear of change only begin to describe the atmosphere in which local land use decisions are made. Add to this the public hearing process which is quasi judicial, adversarial, and unfortunately not designed for resolution of disputes and it is not difficult to see the need for an alternative to present methods. Hopefully, some day we will have a process that will do away with or at least minimize unnecessary, unproductive and unmanageable community conflicts.

Jan 1, 1984

By C. A. Moseley, M. B. Kahle

The Gulf Coast Region has been the center of extensive lignite exploration and development activity in the past 10 years. Currently, 27.2 Mt (30 million st) of lignite are mined annually, the majority of which is uncovered by large walking draglines. Projections indicate that production could reach 125 Mt (138 million st) by 1990. As mining moves to deeper depths, removal of overburden becomes the decisive factor in mine planning and cost. The geology of a region plays a key role in the selection of an overburden removal system. While alternate stripping methods must be analyzed to determine the most economical and operationally sound method, so far bucketwheel excavator systems seem to be the best method for removing large volumes of soft, unconsolidated material that is found at projected mining depths in the Gulf Coast region. Geology of Gulf Coast Lignites Extent Distribution of the principal tertiary lignite-bearing deposits in the Gulf Coast Lignite province extend from the Texas-Mexico border to the Alabama-Georgia state line (Fig. 1). The lignite-bearing strata includes portions of eight states: Texas, Louisiana, Arkansas, Missouri, Kentucky, Tennessee, Mississippi, and Alabama. Lignites occur primarily in the Wilcox, Claiborne, and Jackson groups in the Gulf Coast. The uppermost strata of the Midway group in Mississippi and Alabama also contain significant lignite resources. Reserves Commercial lignite seams in the Gulf Coast Lignite province range from 0.6-3 m (2-10 ft) in thickness. The estimated lignite resources throughout the Gulf Coast in seams greater than 0.9 m (3 ft) in thickness and up to 61 m (200 ft) in depth currently are estimated at 32 Gt (35 billion st). Table 1 shows these resources by state. Quality Lignite quality can vary within individual mining areas and seams. However, trends in quality occur because of the depositional environment, age, and west-to-east geographical location. Better quality lignites occur in the Wilcox group in Texas and Louisiana. Poorer quality lignites occur in the northern regions of the Wilcox group and those of the geologically younger Claiborne and Jackson groups. Environmental Conditions Gulf Coast province environmental conditions are ideal for successful mine reclamation. The lignite occurs in flat to moderately rolling terrain, a topography easily reproduced from the spoil dumps or spoil rows developed during the mining operation. High to moderate rainfall facilitates rapid revegetation. Evidence from current mine reclamation programs and ongoing test plot studies indicate that mined lands can be reclaimed to reach premining productivities. Sometimes productivities are even greater than that of premining conditions. Existing Mining Methods Present Mines & Production There are seven active mines in the Gulf Coast province, all located in Texas (Fig. 2). Lignite

Jan 8, 1983

By J. Partyka

Respirable dust produced during blasting operations in underground mines exhibits both diffusion and convection properties of the airflow. However, the application of the mathematical model presently used to calculate the change in time in the concentration of blasting pollutants is mostly limited to a single drift and cannot be easily utilized for blasts taking place in stopes. This paper discusses an analytical solution based on considerations that enable us to reliably identify the initial condition. Such an approach may be used for any blasting area regardless of its position, its size, or the ventilation system in use during blasting. In addition, a test procedure using field data is established to determined those parameters not measured directly. As well, equations are derived to find the diffusion coefficient, and the position and size of a dust source from the field data. Mathematical considerations The convection-diffusion problem, for a one-dimensional case, is described by the following partial differential equation (PDE): ct. = Dcxx - Vcx + source - sink(1) where C = the concentration of a pollutant T = time V = the mean air velocity in x-direction D = the diffusion coefficient X = distance away from the pollutant source source = any additional pollutant source specified by an initial value problem sink = decay of a pollutant inside the region specified by the boundary conditions. Respirable dust produced during blasting is best considered as an initial value problem (IVP). To derive a mathematical model, the following assumptions are made: •At time zero (t = 0), the dust source is at point x = 0 of an infinite drift. •The problem is considered a one-dimensional case. •The mean velocity of air and the diffusion coefficient are constant. •There is no source or sink of dust other than specified at point x = 0 and time t = 0. We have to solve the following problem [PDE ct=Dcxx-Vcx-m<x...m;0<t<m(2)] ICc(x,0)=f(x)t=0, the initial condition Where c = dust concentration in mg/m3 V= the average mean velocity in a drift in m/s t= time in s D= the diffusion coefficient in m2 /S x = distance coordinate in m. We observe that in problem (2), we have moved the boundaries to[ -m and +m] in order to have an initial-value problem. We introduce new coordinates, s = t and z =x - Vt. To rewrite the PDE in terms of (z, s), we use the chain rule ct = czzt + csst = -Vcz + cs cx = czzx = cz cxx = (cz)x = czz. We now substitute our computed ct, cx. and cxx into the PDE to get new IVP in terms of z and s :

Jan 1, 1991

By E. A. Barrett, L. L. Rethi

Throughout all segments of the United States mining industry, 163 independent contractor employees were fatally injured between 1990 and 1997. Factors that contributed to these injuries were identified after reviewing descriptive information contained in Mine Safety and Health Administration fatality reports for each of the incidents. Thirty-three unique contributing factors were identified and multiple factors were noted for each fatality. Those most frequently discerned were "failure to follow `standard operating procedures"&apos;, (35% of the fatalities), "poor positioning of employee" (26% of the fatalities) and "failure to maintain equipment" (23% of the fatalities). Contributing factors were then associated with the accident and job classifications of the victims. Factors having the highest frequencies in the top five accident classifications where most fatalities occurred were as follows: powered haulage - "failure to maintain equipment"; machinery - "poor positioning of employee"; slip/fall of person - "inadequate fall protection" and "failure to wear safety line"; electrical - "equipment contact with power line"; and falling/rolling/sliding rock - "poor positioning of employee. " Among the job classifications in which most fatalities occurred, leading contributing factors were as follows: truck driver - "failure to follow standard operating procedures" and "poor positioning of employee"; laborer/utility man/pumper - "poor positioning of employee"; mechanic/ repairman and welder - "failure to follow standard operating procedures." Recommendations for utilizing contributing factor information as a basis for safety training are proposed. Training programs may be developed that inform independent contractor employees of factors which, in the past, have contributed to fatal injuries in their job classifications. Then, by combining this information with contributing factors identified in "related" accident classifications, a truly focused training intervention that addresses very specific workplace hazards may he developed.

Jan 1, 2002

By R. E. Miller

Hoisting coal using water and air is a technology which has potential to improve the economics and safety of transporting coal. The Coal Air-Lift Hydrohoist is a prototype coal hoisting system developed by the U.S. Bureau of Mines (USBM). This paper discusses the method used to regulate the supply of water to the 50-m-high hydrohoist U-tube such that the pressure difference at the bottom of the U-tube is held constant. Maintaining a constant pressure difference results in a steady flow of slurry out of the hydrohoist.

Jan 1, 1995

By C. E. Semler

A multiyear program involving online, in-vessel exposures at Barrick Goldstrike Mines Inc. (BGMI) has provided information and experience about the materials and designs for brickwork linings in pressure oxidation autoclaves. A variety of brick and mortar products was evaluated. Properties before and after exposure were used to document the performance. Some benefits include the development of a new silicate mortar, a better understanding of brick requirements and increased autoclave operating time between maintenance shutdowns. BGMI operates six pressure oxidation autoclaves at its Eureka County, NV gold operation. These autoclave process 15.8 k/ld (17,500 stpd) of gold ore. Figure 1 is a flowsheet of the six autoclave circuits. The gold ore is refractory, in which the gold particles are mineralogically encapsulated on a micro- and submicroscopic level. The autoclaves are 4.4- m- (14-ft-) diam and 26 m (85 ft) long (tip-to-tip). Inside of each is a full brickwork (brick plus mortar) lining that divides the vessel into five compartments. Each compartment has a motor-driven agitator that keeps the slurry suspended and disperses the oxygen to enhance reaction. During autoclave operation, the conditions are steady state at 210° to 232° C (410° to 450° F) and 61 to 62 kPa (420-430 psi). As shown in Fig. 1, there are other accessory vessels (splash and flash towers) in the autoclave circuits that are also brickwork-lined. The linings used to date, other than small test sections, have all been acid-resistant fireclay bricks, bonded with alkali silicate mortar, PbO- based mortar and/or vinyl ester mortar, but mainly alkali silicate mortar.

Jan 1, 1997

By B. Waquet

The genesis of a hydrothermal subsea mound, by chimney debris heaping and mineralizing fluid circulating upward, induces a vertical maturation gradient. Connected porosity is easy to measure and, after mineralogical evidence, can be use as a maturation index. Thus, to understand how a rock property evaluates with maturation, it is possible to plot it against connected porosity. Results are that uniaxial compressive strength, Young&apos;s modulus, and in a lesser certitude tensile strength, abrasivity and hardness, increase very weakly with maturation until a maturation threshold (equivalent to a connected porosity equal to 0.2), and rocket to much higher values after it.

Jan 1, 2011

By Raymond Sandiford, Kenneth Xu, Taehyun Moon

Tunnel approach structures situated in slow moving earth flows are subjected to significant earth pressures. The authors have developed a system, utilizing collapsible concrete columns, that limits such loading. The system uses an array of collapsible concrete columns in front of the structure to absorb downslope movement and limit-imposed loads. This concept has been modelled using 3D FEM analyses and a rudimental lab test. For implementation, the collapsible columns would be prefabricated in strengths to mimic the soil strength profile. This concept has merit, and analytical results demonstrate that collapsible columns are a viable means to limit loading.

Jun 23, 2024