Search Documents

By Henry N. McCarl

[ ]

Jan 1, 1966

By J. F. T. Agapito, L. J. Gilbride, K. Hollberg

Room-and-pillar mining at the Big Island Mine uses narrow, yield (i.e., load transferring) pillars to achieve high resource recovery and productivity. Two flat-lying 3- to 3fi-meter (10- to 11fi-ft) seams are mined. The interburden between the seams is about 10 meters (33 ft) and the cover depth is 250 to 330 meters (820 to 1,080 ft).Most of the mining has been single-seam, but two-seam mining will begin in the near future. Yield pillars minimize stress transfer between the seams. However, it is important that good long-term stability be maintained to prevent subsidence over a large portion of the mine beneath the Green River channel. Three stress issues impacting stability are discussed in this paper: (1) higher-than-gravity vertical pre-mining stresses, (2) time-dependent stress transfer or arching, and (3) stresses induced by strata gas. Although the stress environment and behavior is not fully understood, steps have been taken in mine design and operations to minimize impacts to stability. Stress determinations have been very important to verify analytical predictions used in mine design and in long-term stability assessment.

Jan 1, 2004

By A. J. Nugent

Investigations were undertaken to evaluate peroxygen compounds for effective­ness in alkaline cyanide leaching of gold. The addition of peroxygens improved the leach results. Calcium peroxide was the best performed reagent to be employed. Improved reagent consumption followed the trend of calcium peroxide> hydrogen peroxide> no peroxygen addition. In general, preaeration stages could be eliminated, and improved leach rates achieved with no detrimental impact on leach perfor­mance. Interox has not developed an Au Plus (Trade Mark pending) system to utilise this new leach reagent. Initial plant trials are verifying its potential to give additional benefits.

Jan 1, 1990

By John H. Raymer

The accuracy of inflow estimates depends largely on how well permeability is characterized. Permeability is best evaluated as a statistical distribution. For the Chattahoochee Tunnel, this distribution was obtained with a large number of packer tests performed in 50 boreholes along the alignment. The distribution of packer-test data may not accurately reflect permeability, however, due to the limits of the test method and the luck of the field investigation. These discrepancies may be overcome by using log-normal plots of the data to develop a permeability model that will be use din lieu of the data to calculate inflow.

Jan 1, 2001

By Steve Kral

"The Rapid Excavation & Tunneling Conference (RETC) is a world-renowned event that attracts some of the best minds in the global underground construction and tunneling industry. The experts gather at this conference to impart new technologies, discuss challenges to their projects and learn about new technologies that have become available to them.The 2015 RETC will be held June 7-10 at the Sheraton New Orleans, in New Orleans, LA. This biennial conference, of which SME is a sponsor, is expected to attract about 1,400 attendees from around the world. These professionals represent all parts of the global tunneling and underground construction industries - contractors, engineers, owners, consultants and equipment suppliers.More than 110 technical papers in 21 sessions will be presented over two-and-a-half days. Paid attendees will receive a proceedings volume of the conference. The proceedings will also be available from SME. In addition to the technical programming, the accompanying exhibit will include 155 exhibitors occupying 175 booths, providing RETC attendees the opportunity to get a look at the latest in equipment and service technology. Three short courses will be held on the Sunday preceding the start of the show. And there will be plenty of opportunities for attendees to meet and chat during several social activities that are scheduled throughout the conference."

Jan 1, 2014

By G. C. Kachel

Significant effort has been expended and considerable success has been realized m the application of instrumentation and automatic control equipment in the mining and ore processing industries. This effort has been applied principally to process equipment with the objective of increasing throughput, minimizing labor requirements and/or improving grade or product quality. Less spectacular, but quite rewarding has been the successful application of instrumentation and automatic control equipment to a wide variety of material handling equipments. This paper describes some of this work including: (1) automatic weighment of load-haul-dump units and trams underground; (2) automation of skip loading; (3) instrumentation applied in feeders and conveyors; (4) level measurement in bins, silos, vessels and sumps; (5) automatic blending of sized materials; (6) automatic loading of ships, trains and trucks; (7) automatic control of tailings disposal facilities

Jan 1, 1973

By John Ralston, Jinming Duan, David R. E. Snoswell, Daniel Fornasiero, Jingwu Yang

The colloidal stability of synthetic silica spheres with clean, methylated and dehydroxylated sur¬faces was studied at different concentrations of dissolved gas and KCl electrolyte at a fixed pH of 4.2. A classic stability ratio/electrolyte concentration analysis shows that hydrophobic, methy¬lated particles undergo faster rates of aggregation with increasing concentrations of dissolved carbon dioxide. Similar data for hydrophilic particles and dehydroxylated particles show no change as a function of dissolved carbon dioxide concentration. Zeta potential data behave simi¬larly, showing a strong influence of dissolved gas only for methylated particles. The results are interpreted in terms of DLVO theory, with the surface-to-surface interaction dominated by the presence of very small protruding bubbles. Direct evidence for the existence of these very small gas bubbles (or "nanobubbles") was obtained using tapping mode atomic force microscopy. Small bubbles do not form on smooth, hydrophilic, or dehydroxylated silicon oxide water sur¬faces immersed in aqueous solutions under known levels of gas supersaturation. Randomly dis¬tributed small bubbles were observed over the whole surface of observation on methylated surfaces of controlled roughness. Bubbles formed on rough, methylated surfaces were larger and less-densely distributed than those on a smooth surface of similar hydrophobicity. The process of bubble coalescence was observed as a function of time. The macroscopic contact angle, measured with respect to the aqueous or gas phase, is very different from the microscopic contact angle detected by TMAFM and appears to be due to the influence of line tension at the pinned three¬phase contact line. The latter has a value of -3 x 10-10 N and acts to stabilize the small bubbles, flattening them and thereby reducing the Laplace pressure.

Jan 1, 2005

By Gordon M. Pugh, David G. Rasmussen

INTRODUCTION Sublevel long-hole stoping is a large tonnage stoping method that may be used when there is a fairly com¬petent straight vein and the walls will stand with little support. It is a method that lends itself to a high degree of mechanization. Two variations of the method are illustrated in Figs. 1 and 2. Fig. 1 illustrates development typical for a 3-m (10-ft) wide vein. Initial development is by a lower haulageway, which may be either track or trackless. A two-compartment raise is driven in the footwall of the vein. At about 12 m (40 ft) above the main head¬ing, a footwall scram is driven and pockets through the vein are cut on 7.6-m (25-ft) centers. Each of the sub¬level blocks selected in this example is 45.7 m (150 ft) long by 12 m (40 ft) high. Stoping starts at the slot raises at stope endlines and retreats to the timbered raise. This retreat sequence starts on the lowest sublevel and the opening cut is blasted into the slot raise. This retreating system is used in order to provide a good safe back over the miners working in any given sublevel. A crawler-mounted down-the-hole or conventional pneumatic drill puts the holes down from one sublevel to the next on any desired drill pattern. Gravity flow brings the broken ore down to the scram level. The illustration shows a large slusher mounted at the timbered raise and slushing from the pockets back to the raise chute. Development of the ore block in Fig. 2 is typical for a 5.5-m (18-ft) wide vein. Initial development is by a trackless heading driven in the footwall of the vein. Pockets are then put into and through the vein on 7.6-m (25-ft) centers. For ease in using trackless rubber tired mucking equipment, these pockets are crosscut to the vein at approximately 1.04 rad (60°) rather than per¬pendicular. A two-compartment timbered raise is driven down from one level to the next. Endline slot raises are again put through from level to level. Each of the sub¬level blocks selected in this example is 40-m (130 ft) long by 33.5 m (110 ft) high. Stoping starts at the slot raises and retreats back to the timbered raise. Long holes are drilled from one sub¬level down to the next by starting between the lowest pair of sublevels and then working up the ore block. Mucking out of the pocket drawpoints is accomplished by rubber-tired load-haul-dump (LHD) units which then dump into a centrally located orepass.

Jan 1, 1982

By L. L. Anderson

Western bituminous coal can be processed to low sulfur liquid fuels by fast reactions. A process (LEFCO) under development at the University of Utah uses coal and catalyst under hydrogen pressure to convert 60 to 70 percent of the coal matter to fuel liquids and gases. Coals have been processed in small diameter (less than 1/2 inch) tubes and at reaction residence times of less than 10 seconds. Effects of process variables on the yield and quality of products have been studied. General features of the process and the properties and characteristics of the products produced are presented. Special features of the process that distinguish it from other liquefaction processes under development are also discussed.

Jan 1, 1975

By R. Fedel-Moen, R. W. L. Kimber, B. D. Williams, S. R. Ragusa

The use o f cyanide to extract gold from ores is widespread. In the process of extracting gold, cyanide may form metal cyanide complexes with a variety of other metals present in the ore. This study was carried out to investigate the biodegradation of the Cu(I)-cyanide complex and tetracyanonickelate under varying pH and nutrient additions. Detailed studies using shake flask cultures and bioreactors showed that naturally occurring bacteria residing on gold-leach-pad ore uti¬lized the Cu(I)-cyanide complex (CuCN) and tetracyano-nickelate, Na2(NiCN4), as carbon and/or nitrogen sources. Ammonium-nitrogen (NH4+-N) and/or cyanate (CNO-) accumulated in solution as the metal cyanide complexes were degraded. The accumulation of cyanate as a product is a concern due to its toxicity. Degradation rates were increased if a growth substrate (peptone, 0.1%) was added to the medium or if bioreactors were primed with peptone before addition of the metal-cyanide complex. Tetracyanonickelate was degraded at pH 8 without added peptone, but it was not degraded at pH 10. The addition of peptone was required for degradation of the Cu(I)-cyanide complex at pH 8 and pH 10. At pH 8, the addition of peptone resulted in the accumulation of cyanate, whereas, at pH 10, cyanate was not detected in the cultures. Biodegradation of metal-cyanide complexes was faster (approximately 1.5 to ten times faster) in bioreactors than in shake flask cultures. The addition of peptone was not required for degradation of metal-cyanide complexes in bioreactors. However, priming the bioreaetor with peptone resulted in higher metal-cyanide degradation rates over multiple cycles.

Jan 1, 2000

By R. W. Draves

Planning and testing in advance of the mining operation are essential. This advance work can involve physical and chemical analysis of overburden cores, field test plots, green- house studies or any of a multitude of other baseline data collection activities. This paper presents the results of Central and South West's field test plots and how they relate to topsoil substitution. Besides the obvious need for testing in advance of mining, there are the inevitable regulatory requirements. Quoting from the office of Surface Mining Regulations concerning topsoil substitution: 216.22(e) TOPSOIL SUBSTITUTE AND SUPPLEMENTS -Selected overburden materials may be substituted for or used as a supplement to topsoil if the office determines that the resulting soil medium is equal to or more suitable for sustaining revegetation than is the available topsoil and the substitute material is the best available to support revegetation.

Jan 1, 1985

By R. E. Le Messurier

GENERAL DESCRIPTION The mines are located at Broken Hill in the western part of New South Wales, Australia, 930 km west¬northwest of Sydney. Mining Methods Where pillars must be left between stopes, extraction of a block of ore between two or more levels is carried out in stages: 1) Stopes are mined overhand by horizontal cut¬and-fill stoping, or by long-hole stoping. The various methods of horizontal cut-and-fill stoping used are desig¬nated as: -Loader cut-and-fill stoping with horizontal blast¬holes and diesel load-haul-dump (LHD) units. -Open stoping with horizontal blastholes and com¬pressed air or electric scrapers, or with diesel or electric LHD units. Square-set timber stoping, where ground condition precludes open stoping. The backs are sup¬ported with timber square sets. Pattern rockbolting of the backs may be used as an intermediate stage between open stoping and square-set stoping. 2) Vertical pillars are mined by undercut-and-fill stoping or by vertical crater retreat stoping. 3) Where a horizontal pillar has been formed below the level above the primary stope, this level pillar, usually 6.1 to 8.2 m in depth, may be mined by over¬hand square-set stoping or by undercut-and-fill. Long-hole stoping is used at the Zinc Corp. (ZC) and New Broken Hill Consolidated (NBHC) to mine parts of the zinc-rich A and B lodes. Drilling is carried out from drill drives and, in some cases, sills. Hole sizes used are 165 mm (61/2 in.), 110 mm (4'h in.), and 65 mm (21/2 in.) nominal diam with hole lengths being limited to 50, 30, and 20 m respectively. Ammonium nitrate-fuel oil (ANFO) and water gel explosives are used. Broken ore is loaded from drawpoints at the bottom of the stope using rubber-tired diesel-driven LHD units which deliver ore to an orepass. Annual production at Zinc Corp. and NBHC accord¬ing to mining method is given in Table 1. At Zinc Corp. mining is being carried out at depths varying between 200 and 832 m. At NBHC it ranges from 528 to 915 m below the surface. The average travel time to the stope is 30 to 45 min. GENERAL ORE BODY REQUIREMENTS Size, Shape, and Dip There are six separate lodes which carry minable ore in the mines of Zinc Corp. and New Broken Hill Consolidated. The lowest of these and the main ore bodies presently being mined at Zinc Corp. are the lead lodes, consisting of a siliceous fluoritic ore body (No. 3 lens) and overlying it a calcite rhodonitic ore body (No. 2 lens). Each possesses characteristic ratios of lead, silver, and zinc, although the grade within each lens is variable, in places being as high as 30% Pb. There are also low¬grade portions which consist chiefly of poorly mineral¬ized rhodonitic material. No. 3 lens terminates within the Zinc Corp. leases, while No. 2 lens continues into the NBHC leases where it continues to provide a significant proportion of pro¬duction from the mine. Overlying the No. 2 lens are the various zinc-rich ore bodies. In ascending sequence these are lower No. 1 lens, upper No. 1 lens, A lode, and B lode. A typical assay for the small No. 1 lens group ore bodies is 8% lead, 50 g/t silver, and 20% zinc. The `A' lode is a large low-grade ore body in which the higher grade sections assay 4% lead, 30 g/t silver, and 10% zinc; larger quantities of lower grade ma¬terial also occur. B lode, the main zinc lode, typically assays 5% lead, 30 g/t silver, and 17% zinc. B lode increases in size as it extends south, and in NBHC is a major ore body, contributing about 52% of the production. All the lodes pitch south, the average pitch being 0.52 rad (30°) in the Zinc Corp. leases and rather flatter than this in the NBHC leases (see Figs. 1-3). The ground is all competent rock. Production requirements at Zinc Corp. are 900 000 t and 1 200 000 at NBHC.

Jan 1, 1982

By John D. Abbatt, H. B. Newcombe

The Eldorado Epidemiology Project formally began in late 1978. It consists of a retrospective cohort study, to be followed by and to leave in place the mechanism for a prospective cohort monitoring program. These present and future activities are intended to merge into one another. The current study includes all Eldorado employees past and present for whom records are available. The objectives of the undertaking are - 1) to obtain cause-and-effect, dose-response data with which to evaluate the risks to workers in radon and radon daughter containing atmospheres, and to provide additional quantitative information on which to base possible improvements in working conditions; 2) to identify any dead employees of E.N.L. whose cause of death suggests that a potential compensation claim right exists for their survivors, and to similarly identify living ex-employees of E.N.L. whose work histories and states of health suggest potential compensation claim rights. The nature of the study has been determined by the history of Eldorado, which will be described briefly. Eldorado began (as Eldorado Gold Mines) in the late 1920's, operating relatively unsuccessfully in Manitoba. In 1930-31 the emphasis shifted from gold to uranium, and what became the Port Radium mine was first staked. From the very early 1930's until 1942 the company's purpose was almost entirely devoted to the mining of pitchblende - uranium ore - from the Port Radium site, and the extraction of radium from this ore at the Port Hope refinery in Ontario, a process from which the uranium was a largely stockpiled byproduct. In 1942 the company was requested by the Canadian government to accelerate the production of ore, and of uranium. At the same time, all its stockpile of uranium (then being stored in silos as a "waste" product which might later "come in") was acquired for the Manhattan Project. In 1944 the company shares were bought by the Canadian government and the company itself became Eldorado Mining and Refining (1944) Limited; it has operated as a Crown corporation ever since. The name was changed to Eldorado Nuclear Limited in 1968. The Port Radium mine was closed in 1960, and since 1953 the Beaverlodge uranium mine complex has operated on the northern shores of Lake Athabasca. Radium production was discontinued in 1954 when the radium circuit was taken out of the refinery, and since that time the refinery's products have been various types of refined uranium (uranium dioxide, uranium trioxide and uranium hexafluoride) plus metallic uranium. The refinery, of course, processes the company's own yellowcake but as it is one of only five refineries in the western world, most of its work consists of custom refining for a large variety of customers. In addition to the mining and the refining operations, there have been three other divisions involved, and these are, respectively, Aviation, R. & D., and Exploration, in addition to the financial, corporate, administrative and support activities. MATERIAL AND METHODS The human study population (Abbatt, J.D. et al., 1980) consists of all Eldorado employees who have ever worked for E.N.L. and for whom records are available. The total nominal roll to December 31, 1980 is approximately 21,000 and consists of employees of the Mining, Refining, R. & D., Aviation and Exploration Divisions, as well as a relatively small number of other employees (Head Office, etc.). The basic epidemiologic design, as has been mentioned, is for a retrospective cohort study merging into a prospective cohort study, and depending very heavily upon automated record linkage and file matching. The original design called for an initial assembly of the bulk of the nominal roll, prior to the first of two matches with the National Mortality File. The first of these two matches is now complete and the second is to be separated from it in time by 18 months to two years. The second match will be the definitive match prior to the analysis, the interpretation of the data, and the publication of the results. The period between the two matches was designed to permit completion of the nominal roll, including: - addition of previously missing individuals and groups, elimination of duplicates, and amplification of identifying information, - assembly of work histories and exposure information for each individual, - digestion and application of lessons and modifications resulting from the first match with the National Mortality File at Statistics Canada, - preparation of files for the definitive second match. The analysis of data will be carried out by the National Cancer Institute of Canada Epidemiology Unit based at the University of Toronto. This group, with whom Eldorado Nuclear has a memorandum of understanding, have for a variety of reasons, including their familiarity with record linkage and their expertise, been members of the Project Team since

Jan 1, 1981

By Sergio Godoy P.

The Los Bronces porphyry copper deposit is located in the high Andes of Central Chile. Ore is mined from several tourmaline breccias and from an earlier porphyry. After years of experience in the geostatistical estimation of reserves in different zones of the ore body, we believe that success lies in considering the evaluation as an integrated process beginning with the analyses of the drilling density and sampling methodology, ending with the critically important reconciliation between the estimated and the actually extracted ore, in general, when errors or differences occur, focus is centered in the calculation stages of geostatistics. However, this paper demonstrates that all the evaluation stages are equally important and require the direct and continuous geologic input to ensure the best possible estimate within the frame of the geologic constraints.

Jan 1, 1992

By Stephen Stone, Kerby Dobbs, G. Richard Whittecar, W. Lee Daniels, Zach Agioutantis, Tess Thompson

A common result of Environmental Impact Assessments associated with mining projects is the construction of new wetlands in areas disturbed by mining operations. Where appropriate, this mitigation may be considered an integral part of the mine reclamation process under the principles of sustainable development in the minerals industry. Wetbud is a new tool for estimating wetland water budgets using available weather data and site-specific topographic, soil and geohydrologic data, coupled with mass balance mathematics. Wetbud is primarily intended as a planning tool for use in the design of created wetlands, but it can also be applied to native wetlands or wetland restoration sites where the required input parameters can be specified. Wetbud can be run in its basic form where wetland topography, soil parameters and groundwater flux are simplified, or in the advanced form, where these parameters are included in a more complex approach via integration of the MODFLOW package, a free 3D program that was developed by the United States Geological Survey. Both versions can also include overbank flow hydrology sources and the advanced form can also model sloping and irregular topography. The program downloads weather data from the nearest applicable station and selects appropriate wet-normal-dry (W-N-D) years following a modest user data clean-up step. Wetbud also has the ability to utilize existing short-term (e.g. 6 to 9 months) groundwater data from an up-gradient well to simulate longer-term groundwater level inputs for the selected W-N-D years. In addition, Wetbud features a “Wizard” version that comes pre-loaded with 14 pre-selected weather data sets for all areas of Virginia that can develop a simple monthly water budget in less than 15 minutes – a feature that could be expanded anywhere geographically with historic weather data.

Jan 1, 2017

By J. W. Leonard, D. A. Newman

Discussion by N. Standish and P.N. Standish Leonard and Newman (1989) describe concepts and plans of their forthcoming project designed to increase the bulk density of broken coal at various stages of its production and handling. This is an excellent idea and something that will certainly be useful to the coal mining industry worldwide. The authors seek to achieve bulk density increase by "reducing oreliminating, through chemical additives and engineering design, particle voidage and enhance particle consolidation trickling between the point of breakage (at the face) and loading (in the shuttle car) to increase coal bulk density and productivity." In the paper, they present some supporting results of bulk density versus moisture, with or without oil addition, from the steel industry research. Unfortunately, the paper contains many misconceptions and half-truths that detract from an otherwise excellent objective of the project of increasing bulk density by reducing particle voidage-"the bottom line evaluator." Correct. Theory Definitions Coal bulk density is the ratio of the mass of a collection of discrete particles to the volume that it occupies (ASA, 1980). There can be no possible argument about this definition. Mass and volume are readily measured both in laboratory and large scale installations. So, to obtain the bulk density, one simply divides the measured mass by the measured volume. It is here that we come unstuck as everybody who has ever had to reconcile book values with the measured stock tonnages knows. Where does the problem originate? Almost invariably in a too casual a reading of the above definition and the words "a collection of discrete particles." The word collection means "a number of objects collected or gathered together, viewed as a whole" (The Oxford English Dictionary, 1989). If one knows the bulk density of a pile of coal viewed as a whole,

Jan 1, 1991

By A. Tobey Yu

The smelter is the heart of a copper producing operation. Its principal function is to reduce and convert raw copper concentrates and/or leach plant precipitates into blister copper before it is refined. In addition to concentrates and precipitates, typical feed to a smelter also encompasses matte chips, flue dust, flux and lime. By nature, the characteristics of these materials are extremely variable, ranging from sub-micron to lumps, from slurry to dust, from abrasive to corrosive and free-flowing to adhesive. Furthermore, as a result of geological formation, most of the world's open pit copper mines are located in a semi-arid zone, where precipitation is minimal. This particular climate compounds the problem of handling these materials.

Jan 1, 1976

By R. J. Cornelius

Gold with minor associated copper mineralization in the area of what is now the Bougainville porphyry copper deposit has been known since the 1920s and was probably known in German colonial times, pre- 19 14, although no records persist other than a reference by Stanley (1922) to copper specimens from Kieta that he saw in Rabaul. Stanley did not at the time believe that they came from Kieta. Gold was first discovered at Kupei by Jack Comb in 1929 and the Kieta Goldfield was proclaimed in May 1930. In December 1932, the Tapu Reward Claim at Moroni - the site of the Bougainville Copper concentrator, was pegged by C.W.M. Evans who prospected up river from the West Coast. The Pumkuna (Panguna) Reward Claim on the site of the subsequent porphyry copper deposit was granted in February 1934 to G.A. Myers. n May 193 1, the Kupei Reward Claim was transferred to Bou- gainville Gold Options NL and later reverted to Jack Comb and then the Bougainville Syndicate, as did the Pumkuna and Moroni claims. Most of the interested parties had come from the Edie Creek rush on the New Guinea mainland. In 1935, N.H. Fisher, the geologist in Rabaul for the New Guinea administration who later became director of the Australian Bureau of Mineral Resources in Canberra, reported on the three gold areas. Norm Fisher described the gold and copper mineralization and its habit in great detail and this report had a major influence on the events leading to the discovery in the 1960s. Gold production up to the Japanese invasion probably did not exceed $50,000 in value. Half a ton of copper-gold ore from Kupei was sent to O.T. Lempriere's in Sydney for assay in the early 1930s.

Jan 1, 1991

By A. G. Ulsoy

In recent years there has been an Increasing Interest In the application of automatic control theory to mineral processing systems, and numerous applications of mineral process control have appeared in the literature. A general approach to the synthesis of mineral process control systems is presented. The first phase of the control system design consists of specifying the control objectives, process variables and their interactions; these topics will be discussed with specific reference to mineral processing. The second phase Is con¬cerned with selection of control strategies algorithms, instrumenta¬tion, and other components of the control system and is discussed at length. These concepts are then illustrated by a flotation control case study.

Jan 1, 1981

By John H. Canterford

The conversion of nickel and cobalt to the water-soluble sulphates forms the basis of some of the many methods of recovering these metals from their oxide and silicate ores. The applicability of these sulphation processes to a range of Australian oxidized ores is discussed. The chemical and hence mineralogical composition of the ores is shown to have a major influence on the degree of nickel and cobalt extraction. Different sulphation processes are compared, taking into account the influence of ore composition, and considering effects on reagent consumption and on subsequent metal recovery processes.

Jan 1, 1979