Search Documents

By MARK J. VANARELLI

Estimating groundwater inflows in rock deep tunnels is critical to the safety of personnel constructing the tunnel and the cost of construction. This paper presents two case studies for estimating steady-state groundwater inflows into deep rock tunnels. The case studies included the Chattahoochee and Nancy Creek tunnels. In this paper, statistical methods were applied to packer test data obtained from exploratory borings during geotechnical site investigations. A semi-empirical procedure was utilized for estimating groundwater inflows into these deep rock tunnels. It is the most widely used method/procedure in the tunnel industry. The Chattahoochee and Nancy Creek tunnels are deep rock tunnels which exhibit radial flow conditions. For the radial flow condition, a statistical analysis presented in this paper indicates that the semi-empirical procedure works well; however, variations in the procedure and/or an insufficient amount of testing could lead to underestimations of the inflow quantities. Packer test data plotted in histograms were observed in all cases to be log-normally distributed for the radial flow condition. Modeling using Monte Carlo simulations was observed to be an effective tool for removing irregularities in the distribution of the data and incorporating high-end permeability data to derive reasonable groundwater inflow estimates. This paper is based on the PhD thesis entitled “Improvements to the Current State of the Practice in Steady-State, Groundwater Inflow Estimates into Rock Tunnels based on the Application of Statistical Analysis Methods of Packer Test Data obtained from Exploratory Borings During Geotechnical Site Investigations.”

Oct 9, 2020

By Michael von Seebach

High-pressure grinding rolls subject the feed material to pressures of 200 N/mm? During this process considerable size reduction and the Formation of flakes occur. This paper describes the basic consideration For design and operating of this type of mill. It is also shown that the particle size distribution resulting from this process is typical for grinding processes but untypical for crushing processes. High pressure grinding rolls are designed in size of up to 2.8 m roll diameter allowing feed material top sizes of 250 mm. The rigid frame, bearing and drive - train design allows a broad application of the high-pressure grinding rolls operating the machine in open or semi-closed and closed circuit for dry and moist feed materials. Operating results show that capacity increases of up to 100 % can be accomplished with this technology. The high-pressure grinding roll also, allows for lower operating and maintenance costs due to energy savings of up to 20 L and reduction of wear to less than 1 76 for dry and less than 0.1 5 for wet grinding. Other advantages of the high-pressure grinding rolls are smaller equipment sizes than a ball or SAG-mill for a given capacity resulting in lower building sizes with reduced capital in- vestment costs.

Jan 1, 1987

By E. W. Sawyer

Attapulgite is a magnesium aluminosilicate clay mineral which exhibits unique, processing-enhanceable physical and chemical properties that are related to its current commercial uses. Properties of commercial interest are gelling, absorption, adsorption, binding, acid neutralization and many others. Major industrial applications are: (1) absorption by heat treated grades utilized in industrial oil and grease absorbents and in agricultural pesticide carriers; (2) gelling of aqueous liquid products by colloidal grades for stabilization and viscosity control in salt water drilling fluids, suspension fertilizers, liquid animal feed supplements, paints and tape joint compounds; (3) adsorption by heat treated varieties for the removal of catalysts, color bodies and other polar compounds from hydrocarbon streams; (4) gelling of organic liquids by colloidal attapulgite/surfactant blends in oil-type paints, fibrated and nonfibrated asphaltic coatings and mastic compositions, and (5) the binding of feeds and molecular sieve sorpents with colloidal type attapulgite products. These applications and other less common uses and potential uses will be discussed along with, the necessary selective mining and plant processing features related to each property and application.

Jan 1, 1986

By W. W. Dudley

The U.S. Geological Survey, in support of underground testing of nuclear explosives, has developed a technique (Dudley, 1910) to predict the inflow of ground water to large underground chambers that are cylindrical in shape. By treating the chamber as a large-diameter well pumped at constant drawdown, the nonsteady discharge can be computed by the method of Hantush (1961) for analyzing flowing wells under leaky artesian conditions. In mining applications, whether for mineral recovery or for nuclear testing, the most serious departure from the conditions of Hantush's model results from the gradual enlargement of the opening under drained conditions. Inherent in the analytical technique is that the "well" is fully completed at the time that dewatering begins. Because safety is the prime concern, however, initial pumping systems or personnel evacuation procedures must be designed to handle the greatest conceivable inflow. DEFINITIONS Because somewhat different meanings are attached to similar words in different technical fields, the U.S. Geological Survey definitions (Lohman, 1970) of several hydrologic terms used in this report are given below. An aquifer is a formation, group of formations, or part of a formation that contains sufficient saturated permeable material to yield significant quantities of water to wells, and springs. A confining bed is a body of material lying stratigraphically adjacent to one or more aquifers and having a hydraulic conductivity distinctly lower than that of the aquifer. The total head (dimensions L) of a liquid at a given point is the sum of three components: (1) elevation head, he, which is equal to the elevation of the point above a datum; (2) pressure head, hp, which is the height of a column of static water that can be supported by the static pressure at the point; and (3) velocity head, hv, which is the height the kinetic energy of the liquid is

Jan 1, 1971

By E. H. Kurt

INTRODUCTION The simplest way to drill a hole into rock is to strike a steel chisel or drill bit with a hammer. Early miners used this elementary hand technique so successfully in "single jacking" and "double jacking" that the first mechanical rock-drill designers sought to duplicate it. However, in the early developments, the designers were forced to retreat to a construction known as the "piston drill," wherein the entire drilling element is tied to the piston and reciprocates with it. It took nearly 50 years to devise a method of divorcing the two elements and to achieve the original hammer principle used in hand drilling. The Mont Cenis tunnel, drilled through the French Alps in 1861, usually is considered the birthplace of the mechanical rock drill. The Hoosac tunnel in Massa¬chusetts was drilled at about the same time, and the success of these two ventures paved the way for innova¬tions that produced the Burleigh, Ingersoll, Sergeant, and Waugh piston drills between 1870 and the turn of the century. In 1897, George Leyner of Colorado introduced what has been considered the most significant development in rock-drill history. He devised the hollow drill steel for water flushing; when combined with his free-piston hammer drill, this became the first lightweight and dust¬free underground machine. In addition, Leyner's drills introduced improvements such as automatic rifle-bar rotation of the drill steel and chuck, automatic lubrica¬tion, and an enclosed throttle control. During the 1920s and 1930s, automatic feeds, centralizers, sliding cones, and the automatic water back head were developed, laying the groundwork for all pneumatic underground drills currently in use. Since these pioneering efforts, rock-drill development has been concerned primarily with refining the designs and improving the metallurgy to make faster, lighter, and more dependable machines. Fig. 1 illustrates the progress in drilling speed during the first 125 years of rock-drill development; that progress is a credit to the persistence and inventiveness of the designers in the rock-drilling industry. ROCK-DRILL CLASSIFICATIONS To meet the variety of conditions encountered in rock drilling, several distinct types of drills have been de¬veloped. In general, rock drills may be classified as either hand-held or mounted, with the hand-held ma¬chines including the jackhammer or sinker, the jackdrill or jackleg, and the stoper. The mounted drills are com¬monly known as "drifters." Table 1 shows that each type of drill is available in several sizes from different manufacturers. Fig. 2 illustrates a typical rock drill, showing the principal components. The jackhammer or sinker, shown in Fig. 3, is used primarily for general mine utility work such as drilling anchor holes (short vertical holes to bolt or anchor machinery), pin holes (short, usually horizontal holes to fasten sheaves, etc. to side walls), popholes (for blasting large boulders), and similar applications. They also are used for shaft sinking. Jackhammers are classified ac¬cording to weight, and they range from 7 to 30 kg (15 to 65 lb). The rock drill originally known as a jackleg was made by clamping a pneumatic cylinder or leg to a jack¬hammer, both to support the weight of the machine and to feed the tool forward in horizontal or uphole work. The more modern jackdrill refined this concept to make the hinged pivot for the leg integral with the drill cylinder and to group all drill and leg controls in the drill back head for convenience. Fig. 4 illustrates a typical jackdrill. Jackdrills are classified according to cylinder bore size, ranging from 60 to 83 mm (2.375 to 3.25 in.). Because of their light weight and versatility, jack drills are very effective in small drifts, small tunnel head¬ings, and stoping. The larger machines are applied to hardrock formations and in applications where drilling speed is a primary consideration. In soft formations or

Jan 1, 1982

By Kot F. Unrug

When reading different studies discussing trends in coal mining, it appears that a substantial expansion of output by the year 2000 is predicted, even in the most pessimistic forecasts. Depletion of shallow, easy-to-mine deposits is only a matter of time, and the future average mining depth will increase. The proportion of slope to shaft mines operated during the next decades will change in favor of the shaft mines. Since an increasing amount of shafts in new nine developments seems to be inevitable, it appears appropriate to focus more attention on shaft design criteria. Some valuable papers have recently been published (1) that emphasize geotechnical aspects of shaft design. In the discussion that follows some other aspects of design criteria will be evaluated.

Jan 1, 1984

By J. Drelich

An improved experimental procedure to measure contact angle has been consolidated with coal surface preparation involving polishing with abrasive paper, alumina powder, and a cloth, followed by ultrasonic and mechanical cleaning. Specifically, the captive-bubble measuring technique has been compared with the sessile-drop technique and the former has been recommended for the examination of the hydrophobic properties of coal surfaces. Results of the research program, which is currently under way, on the examination of the effect of the nature, amount, size and distribution of mineral inclusions in coal on its wettability are briefly reviewed.

Jan 1, 1999

By Vivek Priyadarshi, VIVEK KUMAR HIMANSHU, A. K. Vishwakarma, M. P. Roy, A. K. Mishra, RAVI SHANKAR

The nature and orientation of joints in rock strata affect the damage pattern under explosive loading. Most of the limestone deposits in India are found with severity of joints. Categorically, these joints may have variable orientations such as dipping out of the blast face, inside the face, horizontally or having strike parallel to the face. The damage pattern under the varying category of orientation will be different. Accordingly, a numerical model in Ansys-Explicit Dynamics was prepared to compare the damages of rock mass under different joint orientations. The physical nature of a joint reflects frictional and stiffness behaviour. Accordingly, the damages have been compared under bonded and frictional nature of joints. The output damage pattern from the model has been validated on the basis of blastability index proposed by Lilly. Different limestone mines in India show different nature of jointing in their rock strata. Accordingly, the blasting outputs from three different limestone mines, viz. Rawan limestone mine, Sagmania and Birhauli limestone mine and Injepalli limestone mine, have been compared along with their blast design parameters and the nature of joint. The comparative results show that the closely spaced horizontal joints support maximum in burden movement and rock fragmentation due to blast.

Nov 23, 2023

By J. Ye

A comprehensive flotation study has been carried out on a Chinese fluorspar ore using the packed flotation column developed at Michigan Technological University. The results are compared with that of a conventional mechanical flotation method on the same feedstocks. Key factors controlling flotation performance of both methods are evaluated based upon a simple statistic design. The flotation concentrate produced in one stage of the packed column has 4-S% higher recovery and much lower silica impurity content than that produced by up to six stages when a conventional mechanical cell is used. The results also show that the packed column flotation process is particularly suitable for recovery of finer fluorspar particles.

Jan 1, 1992

By R. L. Morse

The thermodynamic program is similar to previous mine ventilation programs but has been expanded to consider the compressibility of air. The thermodynamic program does consider: 1) air density variations, 2) humidity changes, 3) intake, exhaust, and underground fans, 4) heat transfer between rock and air, 5) refrigeration of heating plants, both surface and underground, and 6) heat generated by equipment, both diesel and electric. 110st of the compressibility factors are handled in the branch calculations. The field survey necessary to supply-data for this program is quite similar to the basic base and leap-frog pair of stations method used with most incompressible mine ventilation programs. The thermodynamic program is a complete package of ventilation network analysis which can provide mine management with good operational control and planning of mine ventilation systems.

Jan 1, 1977

By John E. Dreier

The Pachuca-Real Del Monte district, Hidalgo, Mexico (Figure 1) has produced roughly 1,500,000,000 oz Ag., 6,000,000 oz Au. and minor Pb., Zn, and Cu from about 100,000,000 tons of ore since discovery early in the 16th century. Production has come from epithermal vein deposits that have been up to 8 km in length, 650 m in vertical extent and 45 m in width but which averaged 200-400 m in length and vertical extent and 2-4 m in width. Ore deposits occur through-out an area about 12 km E-W by 10 km N-S (Figure 2) and between the elevations of 2000 and 2800 m above sea level. The deposits occur as shoots in the veins and terminate laterally where the veins narrow, upward where the veins pinch out and downward where the veins decrease in silver con-tent to below the cut-off grade; the veins are known to extend 500 m below the bottoms of the ore bodies and probably extend to much greater depths. The district lies wholly within a mid-to-late Tertiary volcanic rock sequence that is made up principally of andesite and dacite lava flows and flow-breccias. Although the bottom of the sequence is not exposed in the district, stratigraphic constructions indicate the volcanic rocks to have an aggregate thickness of 2000 to 2500 m. Structurally, the area is characterized by gentil warping and normal faulting of the volcanic rocks. Pre-ore modifications to the volcanic rock sequence consisted mainly of faulting along west-trending, south-dipping normal faults and north-trending high-angle faults.

Jan 1, 1978

By Tyler Luxner

Stillwater Mining Co. (SMC) is the largest primary producer of platinum and palladium in North America. SMC operates two underground mines in south central Montana, along the 45-km (28-mile) platinum/palladium J-M Reef in the Stillwater Complex. The Stillwater Mine exploits 9.6 km (6 miles) of deposit strike length and East Boulder Mine exploits 4 km (2.5 miles) of deposit length. The two mines are 20.4 km (12.7 miles) apart with SMC controlling a considerable length along the entire J-M Reef trace. Production at the Stillwater Mine began in 1986 and in 1988 the first tunnel boring machine (TBM) was commissioned, becoming an integral part of mine development at SMC. TBMs have been used for developing production footwall laterals (FWL) to access new mining blocks at the Stillwater Mine, as well as boring twin crosscut ac-cess tunnels at the East Boulder. Two TBM development expansion projects are currently in progress: the Graham Creek project at the East Boulder Mine, which will extend footwall lateral development 2,591 m (8,500 ft) to the west, and the Blitz project, where a TBM will be commissioned to extend east out of the Stillwater Mine to 3,658 m (12,000 ft) beyond the current production mining front. General strike and dip of the Reef is west to east and to the north, respectively.

Jan 1, 2012

By Elgin D. Bell

Within the next, year or two, Western Canada should overtake Mexico and France. to become the worlds second largest producer of elemental sulphur, surpassed only by the United States, By 1965, it should produce about 25% of the world's total elemental production and, about 10% of sulphur produced in all forms. In 1952 Alberta had but one small sulphur recovery plant. By 1962, it had fifteen plants with a total designed capacity of almost 6,000 long tons of sulphur per day and actual production of almost one million long tons per year. This decade of dynamic growth was the result of Alberta's rapidly developing natural gas industry. More particularly it was the result of approval in 1960 to export natural gas in large volumes into the United States. Prior approval to export gas from Alberta to eastern Canada and relatively modest volumes to the U. S. had resulted in the construction of several plants but none were of the scale required to serve the U. S. market.

Jan 1, 1963

By Erik Vlot

"The mining industry has recognized the advantages of high density backfill or ‘paste’, which is typically pumped with a hydraulically driven piston pump. Due to the discontinuous flow of this type of pump, pressure pulsations can occur in the discharge line. Pressure pulsations are an undesired phenomenon in pumping installations for a number of reasons that include: damage to the pumping system; piping and supports; disturbing noise levels; and even safety risks for operators and maintenance personnel.This paper describes an advanced system on the GEHO® piston pumps, which will prevent virtually no pressure pulsations from occurring, rather than merely reducing the already existing pulsations.INTRODUCTIONThe first GEHO® hydraulically driven piston pump was developed in the mid-1970s. It was an industrial design pump designed to operate in the high-standard industrial environment with regards to operating hours per day, duties, maintenance and lifetime of the pump and spare parts. This type of pump has a proven track record and has been further developed for the type of applications that we are describing today. The special feature of this pump type is its ability to pump extremely viscous slurry with solids content of up to 90% by weight, at high pressures. Typically, in the mining industry, this pump is used for tailings transportation, with a focus on mine backfill and is often referred to as a paste pump.In the 1980’s the hydraulically driven piston pump made its entry into the application of mine backfill, thanks to the high discharge pressure capabilities enabling the mines to pump higher density (i.e. higher solids concentration) slurries and pastes over longer distances.Part of the ongoing development was (and still is) the increase in discharge pressure and flow capacity to comply with the ever growing demands for high power piston pumps. In line with the technological developments and increase in performance duties, the popularity of this pump type increased significantly and many other industrial applications have discovered the benefits of this pump type.Together with the increase in pump discharge pressures and flow capacities the effect of an undesired phenomenon also increased: the phenomenon of pressure pulsations. Before we explore this subject in more detail it is important to first understand the design and the characteristics of a hydraulically driven piston pump."

Jan 1, 2017

By C. A. Rawlins, P. Rostami

"Ventilation systems are not only an integral part of any underground mine design but are a significant contributor to the mine’s capital and operating costs. The ventilation and cooling design systems presented in this paper were part of the prefeasibility evaluation of an underground platinum mine in South Africa. The mine would ultimately operate at the depth of 1,200 m below surface with a proposed 4 Mtpa production rate. The proposed mining operation is a highly mechanized operation using diesel equipment. Significant daily production rate, large amount of equipment and expansive nature of the operation, contributed to a challenging while flexible ventilation design requirements. This paper presents how to safely and efficiently optimize capital expenditure and operating costs associated with the mine air cooling and refrigeration system through practical ventilation design practices. Successful capital and operational savings by modulating installation and commissioning of refrigeration facilities can influence the economic realization of such systems. The adapted planning and design approach provided a cost-effective advantage while complying with design safety and regulations. INTRODUCTION This paper outlines a prefeasibility evaluation of the heat loads and related cooling system to be employed at the proposed platinum mine. The paper also provides appropriate details for a comprehensive understanding of the applied methodology. The proposed mine will be a trackless underground operation using a combination of mining methods. Initially, ore zones with vertical thicknesses greater than or equal to 18 m will be mined using the long-hole stoping (LHS) method, while thinner ore zones will be mined using mechanized drift-and-fill or drift-and-bench methods; hence, a highly mechanized operation with LHDs, trucks, drill rigs, personnel carriers, etc. is envisioned. Broken rock (ore and waste) will be transported by the means of trucks to the main passes (ore and waste) and collection points. Mining zones identified in the project occur at depths ranging between approximately 700 m to 1,600 m below surface. Primary access to the mine will be via a 1,100 m deep, 10 m diameter production shaft (named Shaft No. 2), three additional shafts will be sunk to provide future ventilation and production support. Three main access levels are established as primary haulage levels and include a series of interconnecting ramps. Additional mining sublevels will be developed as necessary. Figure 1 shows the proposed shaft locations and main access levels in a 3-D elevated view. Mining is performed using highly productive mechanized methods. For this reason, an annual ventilation estimate is based on requirements for mobile equipment (i.e., 0.06 m3/s/kW). The air requirements imposed on the underground operation is further influenced by equipment heat loads, auto compression, and virgin rock temperature, as the main sources of in-mine heat."

Jan 1, 2015

By Jung-Joo Kim, Jong-Uk Kim, Turab H. Jafri, Han-Kyu Yoo

"INTRODUCTION Steel sets such as H-type and lattice girders are often installed in the tunnels before the hardening of shotcrete to ensure the stability of conventional tunnels in soft ground conditions. In practice, while designing the tunnels with the help of numerical analysis, steel sets are generally considered only as temporary support elements. Only a few studies propose the direct application of composite support in the tunnel design, based on large-scale experiments and numerical analysis. In order to assess the structural performance of the composite support consisting of shotcrete and steel sets, large-scale experiments were performed on two types of arch-shaped specimens by applying the combined effects of axial forces and bending moments. Based on the experimental results, numerical analysis was performed to assess the application of composite support in tunnel design. The crown settlement, axial forces, bending moments, and load distribution in the composite support were analyzed in the light of different structural patterns. LARGE-SCALE EXPERIMENTS USING COMPOSITE SUPPORT Preparation and Procedure of the Experiments The preparation setup as well as the organized procedure of the large-scale experiments using composite support is shown in Figure 1. An appropriate geometry of the specimens was selected by considering the standard cross-section of a two-lane highway tunnel in South Korea. Under the loading conditions meant to develop the axial forces and bending moments simultaneously, arch-shaped specimens were assembled with the ends of the specimens subtending a 60° arc angle at the center of the arc circle as shown in Figure 2. The fabrication of six specimens was completed in two groups based on the dimensions of steel sets, with the first group of three specimens being reinforced by H100 (No.1, No.2, No.3) and the other three by H125 (No.4, No.5, No.6). In order to reduce the voids on the boundary of the shotcrete and steel sets, concrete was casted over the steel sets instead of using shotcrete. The specimens were designed to incorporate the uniaxial compressive strength of 21 MPa. Shear keys and steel plates were installed at the ends of the specimens, so that shear failure could be avoided at the ends and the specimens could also be protected from detachment at the fixation. Translational and rotational movements at the ends of specimens were fixed."

Jan 1, 2016

By J. H. Wilhelm

Continuous thickeners can be sized either from previous experience, continuous pilot-scale test results, or from batch settling tests. Although it is a relatively simple process to size full-scale thickeners when previous experience or pilot-scale operating data are available, batch testing is often the only realistic method for sizing thickeners due to time restrictions, budget limitations and availability of sample material. Many authors have, therefore, suggested means of running batch tests and analyzing the resulting data. Fundamental thickening theory had its beginning with the work o£ Coe and Clevenger(1). In order to determine the size of the thickener settling area, they proposed that a series of batch settling tests be run at various initial concentrations. The solids handling capacity at each concentration can then be determined and the lowest capacity (maximum area requirements) used to size the thickener. Kynch(2) developed a mathematical analysis in which the relationship between solids concentration and settling rate can be obtained from a single batch settling curve. Talmage and Fitch(3), Yoshioka(4)(5) and Dick(6), have enlarged upon these works to give a basis for methods of sizing thickeners.

Jan 1, 1979

By Bahaa Alyosif, Murat Erdemoğlu, Muhammet Kürşat Aydemir, Turan Uysal

The effect of intensive milling on the conversion of microcline ( KAlSi3O8) to potassium chloride (KCl) occurred during the chlorination roasting process for artificial KCl production was investigated. A feldspar ore with 10.89% K2O grade and containing microcline was dry milled by a planetary ball mill for mechanical activation. Milled ore mixed with calcium chloride was roasted at temperatures between 500 and 1000 °C to get the chlorination roasting process. The product was then leached in water to dissolve KCl occurring during the roasting, which will be precipitated from the pregnant leach solution by evaporation. Results showed that potassium recovery from the unmilled ore increased rapidly up to 800 °C, and dramatically decreased at higher temperatures due to the removal of KCl from the furnace by means of evaporation. A potassium recovery of 31.95% was achieved by the unmilled ore, whereas it was 88.43% when 15 min milled ore was roasted at 750 °C. It was concluded that intensive milling caused mechanical activation of microcline to reduce the roasting temperature of the chlorination roasting process.

May 31, 2023

By Xuehui Li, Xinshuai Shi, Jun Wang, Jianguo Ning, Shang Yang, Zhaohui Zhang

Pressure relief is an important step in preventing and controlling rock burst disasters. Hydraulic slotting has emerged as a strategy for pressure relief and energy release in roadway surrounding rock. There is no qualitative description for the response relationship between hydraulic slotting parameters and the degree of pressure and energy release in a roadway, which is a scientific problem. In this paper, theoretical analysis, numerical simulation, and on-site industrial practice were comprehensively used. First, a structural model for the pressure relief and energy release of coal by hydraulic slotting in a deep roadway was established, and the pressure relief and energy release principle by hydraulic slotting was revealed. The principles and methods for determining hydraulic slotting parameters in the roadway were proposed. Three evaluation indices for the pressure relief and energy release effect of coal after hydraulic slotting were proposed, namely, the stress ratio of coal, elastic energy density ratio of coal, and displacement rate of the roadway rib. According to the evaluation indices, the degree of pressure relief and energy release was divided into three levels: reverse pressurization, full pressure relief, and transitional pressure relief. Then, a FLAC3D numerical model was constructed, the levels of pressure relief and energy release under different hydraulic slotting parameters were analyzed, and the optimal slotting parameters were determined. Finally, on-site industrial practices were carried out in Panel 7312 of the Xinhe Coal Mine. An effect test showed that the effect of pressure relief and energy release was remarkable after hydraulic slotting was adopted on the roadway surrounding rock, which can effectively reduce the risk of rock bursts. These research results can further improve hydraulic slotting technology systems and provide a theoretical basis and technical reference for the stability control of deep roadway surrounding rock.

Sep 20, 2023

By J. -B. C. Varnier, J. A. Cremeens, D. D. Overton

"Slope failures that occurred in 2008 and 2009 at the Pikeview Quarry in El Paso County in Colorado in the United States were investigated using three-dimensional discrete element modeling methods. Large-scale block sliding failures occurred along weak bedding planes that dip steeply into an excavation located at the toe of the slope. Several mining sequences at the toe of the slope were simulated to evaluate the effects of various degrees of extraction and backfill on slope stability. Slope stability back-analysis was conducted using prefailure and post-failure conditions to determine the joint shear strength properties. Laboratory testing was also conducted to determine intact rock properties. Three-dimensional discrete element analysis was uniquely applicable to this evaluation because it allowed representation of shear stress of the basal sliding surface and afforded evaluation of several scenarios of extraction and backfill at the toe of the slope. IntroductionThe Pikeview Quarry is an aggregate quarry located approximately 8 km (5 miles) northwest of Colorado Springs in El Paso County, CO, USA. The quarry has been operated by several owners since the early 1900s. According to the U.S. Mine Safety and Health Administration (MSHA, 1986), the quarry has been a major source of construction aggregate for the Colorado Springs area for many years. In the 1950s, the site was mined by Peter Kiewit and Sons to provide limestone for the construction of the nearby Air Force Academy.A large-scale slope failure occurred on Dec. 2, 2008, which stopped mining activity at the Pikeview Quarry. A second, related slope failure occurred on Sept. 13, 2009. The second slope failure was located immediately adjacent to the initial December 2008 failure.The objective of this paper is to discuss the three-dimensional slope stability evaluation. The causal relationships of slope instability are not within the scope of this publication. However, omitting the precursors to slope failure would limit understanding of the nature of the slope stability evaluation. The regional and local geology and the history of slope instability at the Pikeview Quarry aid in understanding these precursors. Two main failure mechanisms were hypothesized during the failure investigation to explain the triggering of the 2008 and 2009 large slope failures at the Pikeview Quarry, and both of these mechanisms were given equal credence in the present study. Quarry excavation and backfilling was a key factor in the slope instability for both failure mechanisms. The excavation was backfilled in stages in an effort to provide slope support. The objective of the three-dimensional model was to evaluate the effects of extraction and backfill at the toe of the slope with respect to slope stability."

Jan 3, 2018