Search Documents

By B. Holen, J. R. Baregi, J. A. Organiscak, A. B. Cecala

The National Institute for Occupational Safety and Health (NIOSH) cooperated with 3M Company in the design and testing of a new environmentally controlled primary crusher operator booth at the company’s Wausau granite quarry near Wausau, WI. This quarry had an older crusher booth without a central heating, ventilation and air conditioning (HVAC) system, and without an air filtration and pressurization system. A new replacement operator booth was designed and installed by 3M based on design considerations from past NIOSH research on enclosed cab filtration systems. NIOSH conducted pre-testing of the old booth and post-testing of the new booth to assess the new filtration and pressurization system’s effectiveness in controlling airborne dusts and particulates. The booth’s dust and particulate control effectiveness is described by its protection factor, expressed as a ratio of the outside to inside concentrations measured during testing. Results indicate that the old booth provided negligible airborne respirable dust protection and low particulate protection from the outside environment. The newly installed booth provided average respirable dust protection factors from 2 to 25 over five shifts of dust sampling with occasional worker ingress and egress from the booth, allowing some unfiltered contaminants to enter the enclosure. Shorter-term particle count testing outside and inside the booth under near-steady-state conditions, with no workers entering or exiting the booth, resulted in protection factors from 35 to 127 on 0.3- to 1.0-µm respirable size particulates under various HVAC airflow operating conditions.

Jan 1, 2015

By L. Vandamme, J. H. Curran

A fully three-dimensional hydraulic fracture propagation model, based on the Displacement Discontinuity Technique, is briefly described. Using this model, it is shown that the geometry of a propagating fracture is dependent on several factors, among which the fluid pressure distribution within the fracture plays an important role. The containment of hydraulic fractures is found to be dependent on stress and toughness barriers in the formation. Containment is also observed to be more effective with a decrease of the viscosity, pressure or flow rate of the injected fluid. The three-dimensional layout of the fracture is shown to have a definite influence on the width and pressure distributions within the fracture. The examples considered indicate the need for fully three-dimensional models, as complements to the commonly used two-dimensional and pseudo-three-dimensional models.

Jan 1, 1986

By T. V. Johnson

The microstructural relationships in dolomitic fluxed taconite pellets were studied. The influence of basicity (in the range 0.75 to 2.1) and firing temperature (to 1340°C) on the grain structure, macrostructure, and mineralogical phase relationships are described. Extensive slag bonding of hematite grains begins at temperatures between 1220 and 1230°C, and results in fundamental changes in grain structure. Successive temperature increases result in little change in grain structure until 1340°C, when extensive coalescence of the hematite grains begins.' Increasing flux additions have little effect on grain structure but greatly influence pore character. The compressive strength decreases with increasing flux addition, increases with increasing firing temperature, and is related to the macrostructure of the pellet. The compositions of the slag phases are represented on the CaO-Fe2O3-SiO2 phase diagram, and the compositional path of slag development is described.

Jan 1, 1980

By Maurício L. Torem, Isabella A. Scorzelli

Taboca Mining is one of the largest producers of tin in the world. In its pilot plant, significant amounts of a middling of 90% xenotime (YPO4) and 10% zircon (ZrSi04) are produced. Until now, these minerals of this ore body could not be separated successfully. This paper presents some aspects of the fundamentals of xenotime and zircon flotation with anionic (fatty acids) and cationic (amine acetate) collector, as well as the influence of the superficial leaching of the minerals with cold HCI and HNO3 on the floatability. The mineralogical studies showed that both minerals are optically liberated in -212+106 µm size fraction. Surprisingly, SEM analysis indicated that both xenotime and zircon contain very small inclusions (1-5 µm) of thorite (ThSiO4). On the other hand, zircon is fairly metamictizated giving rise to malacon. Zeta potential tests showed that the isoelectric points of xenotime and zircon correspond to a pH value of 4.5 and 4.7, respectively.The pretreatment with HCI and HNO3 displaced the isoeletric point (IEP) of the minerals to the left. The microflotation tests indicated that the floatability of both untreated and treated minerals are quite similar in the presence of the collectors studied in this work. Adsorption mechanisms are also suggested.

Jan 1, 1995

By T. Petrov

This study was performed to analyze the behavior of the blowing curtain face ventilation system modified with a specially designed regulator, called Wing Regulator. The purpose of the regulator is to extend the airflow penetration depth toward the face and allow effective face ventilation at curtain setback up to 13.7m (45ft) from the face. A small scale model of the Wing Regulator was successfully tested in the Mine Ventilation Laboratory at the University of Kentucky. Then a prototype of the proposed regulator was tested in full-scale in mine environment. Series of three dimensional simulations were performed to support this research using validated CFD code. This paper presents results of the performed studies and discuses the advantages of using the Wing Regulator. Presented information relates to the US Provisional Patent Application No 61/818,112.

Feb 23, 2014

By Peter N. Blakey

The Kidd Creek orebody is a massive, base metal deposit with widths up to 600 feet and a strike length of 2,200 feet. The orebody dips eastwards at 70° to 80° and is amenable to sub-level open stoping. Five distinct zones (Fig.1) based on structural wall rocks and ore type parameters occur within the orebody. These zones are: Zone 1 - Mainly copper stringer ore Zone 2 - Massive pyrite ore Zone 3 - Massive sphalerite and chalcopyrite Zones 4 and 5 - Are banded and variable in nature Compressive strengths vary from zone to zone with an average of 22,000 p.s.i. and highs of 40,000 p.s.i. The mine is developed from a ramp extending from surface to the 1600 foot level and a 24 foot diameter, 3050 foot vertical shaft with main levels at 400 foot intervals. Sub-levels at 100 foot vertical intervals are driven from the ramp. transverse and longitudinal pillars to support the crown pillar left under the open pit. The layout allows an opportunity to enlarge or reduce pillar sizes and also to introduce fill on any horizon should conditions warrant. It also offers a large number of operating stopes spread through the various ore zones giving good ore blending characteristics. All ore from the stopes is handled through drawpoints using Wagner ST8 scooptrams with an average one way haul length of 650 feet.

Jan 1, 1976

By Alain S. Kivava, Olawale K. Aromolaran, Charles Nzolang, Anthony T. Bolarinwa, Georges M. Kasay

Rare earth elements (REEs) are crucial in high-tech and green technologies. The Democratic Republic of Congo (DRC), rich in mineral resources, shows potential for REE deposits in carbonatites, pegmatites, and placers. This paper reviews global REE resources, highlights potential REE targets in Africa, and emphasizes the need for further research and exploration in the DRC to unlock its REE potential.

Feb 4, 2022

By Iwasaki I.

This article discusses the effect of physical and chemical modifications of starches on the anionic and cationic flotation of silica from oxidized iron ores and magnetite-taconite concentrates, and the results of the interaction of starch, pH, and calcium ions on the flocculation, clarification, and filtration of iron ore slimes and magnetite-taconite tailings. Starches, particularly when anionically modified, were found to be effective depressants in anionic silica flotation. British gums and dextrins were beneficial for oxidized iron ores, but none of the starches or starch derivatives appeared to have any effect on magnetite-taconite concentrates. The flocculation and filtration of iron ore slimes were most strongly affected by the level of starch, to a lesser degree by the pH, and were virtually independent of the level of calcium chloride. The clarification of iron ore slimes was complexly dependent on these three factors. The flocculation of magnetite-taconite tailings depended mainly on the level of starch, whereas their clarification depended on the level of lime. As previously reported in the literature, selective flocculation and partial upgrading of a semi-taconite could be readily attained with starch and calcium chloride.

Jan 1, 1968

By L. Patts, J. Rohrbaugh

The Mine Safety and Health Administration (MSHA) has received several reports of filters igniting when high-temperature disposable filters were used on non-cooled diesel exhaust systems in underground coal mines. Based on laboratory testing (to determine the ignition temperature of these filters, which were loaded in the field with diesel particulate matter, or DPM), MSHA determined a maximum safe operating temperature for high-temperature disposable filters. When the results of the laboratory filter ignition testing were reported to the Coal Diesel Partnership (comprised of members of the Coal Industry, Labor, NIOSH and MSHA) the Partnership charged NIOSH with investigating the safe use of high-temperature disposable filters. This paper reports on the design, fabrication and testing of a unique exhaust gas cooling device and the ability of this device to successfully lower filter inlet temperatures and thus reduce the potential for fires.

Jan 1, 2009

By Earle Faig

Along with other transportation modes, the barge industry will be greatly effected by trends in domestic coal production. Traditionally, coal has been one of the major commodities moved by barge. Now, because of events in the international energy market, coal is finally getting the recognition it deserves as a major component of the country's energy program. Perhaps even more significantly, a series of events have caused other countries to turn to the United States as a source of coal. Although the outlook for coal demand is optimistic, it will be greatly influenced by the ability of the transportation sector to handle the additional traffic. Because of our long experience in moving large quantifies of coal, the barging industry is in an excellent position to capitalize on coal's increased popularity. A brief description of the barging industry should facilitate the discussion of coal as it relates to the barging industry. Barge companies operate on a 40.23-Mm (25 000 mile) river system which includes the East and West Coasts and the Mississippi River System. Included in the Mississippi River System are the Allegheny, Monongahela, Kanawha, Ohio, Illinois, Missouri, Tennessee, Cumberland, Arkansas, Warrior - Tombigbee and Mobile Rivers as well as some smaller tributaries. The Gulf Intracoastal Waterway, which stretches along the Gulf Coast from Brownsville, Texas to Apalachicola, Florida, is also considered part of the inland waterway system.

Jan 1, 1981

By J. H. Gasper

The overall success of steep slope (>20°) contour mining is dependent upon many factors. The major factor is the selection of the mining method that best suits the premining site conditions both environmentally and economically. These conditions can be divided into three major categories: 1) Geometric Conditions --machine limitations, slope stability restrictions, erosion capacity, among others; 2) Physical Conditions--material properties, rock strengths, diggability, driving surfaces, among others; 3) Chemical Conditions --acid/base relationships, blending or selective placement of overburden, among others. This paper incorporates these conditions through conceptually modeling compliance oriented contour mining methods; in particular Haulback methods, utilizing: 1) the Front-End Loader (FEL)/Truck; 2) Tractor Scrapers; and 3) Combined FEL-Truck/Scraper. Engineering analyses including machine selection, sequencing, ease of varying production rates, slope requirements (for stability and running surfaces), drainage requirements and many others can be performed after the geometric constraints dictated by in-situ conditions and regulatory requirements have been conceptualized. Once all generalized geometries have been established, reduction to idealized three-dimensional views is achieved. These are then reduced to two-dimensional symbolic models, mainly plan views, but also elevations and sections. Equipment activities and operations are then conveniently overlayed. Without this simple two-dimensional reduction, technology transfer remains awkward and non-analytical.

Jan 1, 1991

By Karl V. Lindell

Asbestos is not the name of a distinct mineral species, but rather the commercial term applied to the fibrous form of several minerals differing widely in composition. There are some 30 known varieties of asbestos but of this number only 6 are of economic importance, and these, in order of economic significance are chrysotile, crocidolite (or blue asbestos), amosite, anthophyllite, actinolite and tremolite. Chrysotile asbestos was formed by the introduction of hydrothermal solutions into fractures in serpentinised ultrabasic host rocks. These solutions dissolved magnesium silicate from the wall rocks, and with subsequent lower temperature and pressure they became supersaturated, and crystals of chrysotile asbestos formed. The chemical composition is variable but is classified as a hydrous magnesium silicate, containing a high percentage of magnesia and water, plus varying amounts of alumina and ferrous and ferric iron. Other asbestos minerals are formed by a similar process but with a different host rock e.g. crocidolite occurs only in iron' formation. The chemical composition of asbestos minerals other than chrysotile, shows a wide variation, but in general may be classified as silicates, or metasilicates, containing varying amounts of calcium, magnesium, sodium and iron.

Jan 1, 1964

By JOHN R. HEBERGER, MAHIYAR F. NASARWANJI, Jonisha P. Pollard, Lydia M. Kocher

nt in the mining industry, and identifying factors associated with these injuries is critical for developing prevention efforts. This study identifies nonfatal injury incidence rates, nature of injury, work activities, glove usage, and sources of hand and finger injuries in the U.S. mining industry, as reported to the Mine Safety and Health Administration (MSHA) from 2011 to 2017. Hand and finger injuries occur at a rate of 6.53 per 1,000 full-time employees, which is nearly double the rate of the next highest affected body part, the back. Most of the hand and finger injuries were classified as cuts/lacerations/punctures (53 percent) followed by bone fractures/chips (26 percent). Materials handling and maintenance/repair were common activities at the time of the incident with miscellaneous metals — such as pipe, wire and guarding — and hand tools as the primary sources of hand and finger injury. Although the information on glove use was limited, leather gloves were most often worn when an injury occurred.

By B. Y. Wong

In April 1989, Southern Company Services signed a 3.5 year contract with DOE-PETC for generic engineering development of an advanced physical fine coal cleaning technology known as selective agglomeration. This technology offers the potential for significantly higher pyritic sulfur removal (90% +) than conventional coal cleaning (30 to 50%) while maintaining high Btu recovery (90% +). Engineering development will include bench-scale process development; component development; adaption or modification of existing unit operations; proof-of-concept (POC) module design, fabrication, testing and evaluation; and small commercial facility conceptual design. The information obtained during POC operation will be sufficient to result in a technical and economic design base that can support construction and operation of a small commercial plant. The major goal of the research is to develop selective agglomeration technology to achieve 90% pyritic sulfur removal while operating at Btu recoveries above 90% based on run-of-mine quality coal. This objective will be accomplished in two phases: Phase 1 -bench-scale and component development, and Phase 2 -POC module operation and conceptual design of a small commercial plant. Currently, work is proceeding under Phase 1 (Tasks 1-7) of the project. A review of the status of Tasks 1-7 is presented in this paper.

Jan 1, 1991

By N. A. Abdel-Khalek

The objective of this investigation was to compare the results of counter-current flotation column versus conventional flotation cell for the cleaning of a sulphur ore and its discrete size fractions. The tests were carried out using diesel oil as a collector and alcohol as a frother. Generally, flotation column produced concentrates of higher grade. For example, the grade of a rougher concentrate for a given feed obtained with the column increased by 33% higher than that produced with the flotation cell. Such higher grade could not be obtained using conventional cell even after 3 cleaning stages. Moreover, the column gave superior results for flotation of fine and ultrafine particles.

Jan 1, 1991

By Greg Colzani, Emily Thompson

The 3RPORT Project, includes a 5-mile tunnel excavated by a 19-foot diameter slurry Tunnel Boring Machine below the city of Fort Wayne, IN. The Geotechnical Baseline Report (GBR) indicated vuggy to massive argillaceous dolomite within the tunnel alignment. During excavation of the first reach, the TBM encountered zones of cohesive clay and sandstone presented in full face and mixed face conditions. The occurrence of Sandstone was not a “Baselined Condition” described in the GBR for this reach of the alignment. This paper will discuss the methodology to investigate, mitigate and evaluate the DSC impacts on TBM performance.

Dec 1, 2022

By Richard E. Otoo, Evan J. Owen, Virginia T. McLemore

According to the U.S. Geological Survey (USGS), a critical mineral is one that is essential to the economic well -being of a nation and whose supply may be disrupted due to geological, geopolitical or environmental factors (Nassar et al., 2020). For example, REEs are critical to the production of electricvehicle motors as well as wind turbines, yet China’s share of their global production rose to more than 95 percent in 2010 (IEA, 2021). China’s share has since declined, with production quotas dropping to nearly 70 percent by 2023 (Statista, 2023). This and similar situations with many of the critical minerals raise deep global concerns about supply-chain vulnerabilities (Bauer et al., 2011). Critical minerals are used in the production of renewable energy, electronics, agricultural products and common household items (McLemore, 2020). As the global demand for these minerals continues to grow, it is not sufficient to rely solely on scaling up production from existing operations. While increasing production from known deposits can provide short-term relief, long-term resource security requires discovering new, economically viable mineral resources. One of the most effective ways to secure future supply is through mineral exploration, which increases the global inventory of critical minerals and also minimizes risks posed by market monopolies and political instability. The major challenge of mineral exploration lies not only in identifying mineralized deposits but also in determining whether discovered concentrations are sufficient to warrant further investigation and development. A fundamental concept in this decision-making process is using cut-off grade. In this article, cut-off grade refers to the minimum concentration of minerals required to justify further exploration efforts based on factors such as type and size of mineral deposit, mining and processing technologies, associated byproducts/coproducts and the market price of these minerals. Typically, economic cut-off grades are used to determine whether a mineral deposit can be mined profitably. However, this article focuses on preliminary cut-off grades needed to establish whether the amounts of critical minerals within a deposit are high enough to justify further exploration and detailed evaluations. By comparing mineral deposit grades, size, production and extraction technology, and other economic factors with established and active mines, exploration teams can estimate cut-off grades that justify further exploration.

Aug 1, 2025

By Patrick G. Hatcher

Studies of sedimentary humic acids by nuclear magnetic resonance (NMR), stable isotopes, and elemental analysis show they are derived by oxidative degradation of complex plant macromolecules that are insoluble in aqueous or organic solvents. The mechanism by which humic acids originate is fundamental to our understanding of the role of organic matter in ore deposition, because these substances can complex and mobilize a number of metal ions. The organic matter associated with uranium ores of the San Juan Basin, New Mexico and Carlin-type disseminated gold deposits of Nevada has certain organic geochemical characteristics that suggest an origin from humic acids.

Jan 1, 2013

By Richard J. Lundin

Literature research is an inexpensive, yet effective tool for the direct discovery of ore deposits. Case studies abundantly demonstrate that properties with viable mineralization and *proven reserves have been overlooked, forgotten. or ignored and can be rediscovered by inexpensive literature search techniques Areal studies s as WaIlaby Enterprises Mining District Data Base Program appear to be more effective than traditional commodity studies. The success of such studies depends on the inclusion of Mineral Clairant Questionnaire Data, Mineral Ownership Data, Field Examination Data and the continual updating of all information. Such studies are valuable for proposed or existing Wilderness Area Evaluations.

Jan 1, 1977

By J. Fuller, J. Beale, Q. Justice, Z. Agioutantis, S. Hicks, Z. Khademian

Seismic events can be induced by mining due to unstable rock failures or slips along geologic structures leading to the sudden release of strain energy stored within the rock near underground openings. Depending on their intensity and proximity to the working area, seismic events may raise safety concerns, and thus the forecasting of the seismic potential in advance of mining can mitigate safety hazards. The integration of seismic data into geomechanical modeling can provide a tool for identifying areas with elevated potential for seismic activity. In previous works, a methodology was developed to forecast seismic potentials in a pseudo-2D geomechanical model. In this paper, seismic events, ranging in magnitude from about -1.0 ML to 3.7 ML, recorded in a deep longwall mine (> 450 m) in Virginia during mining of six adjacent panels, were evaluated to identify areas where larger magnitude events (> 1 ML) had occurred. A three-dimensional geomechanical model of the same area was constructed in the 3DEC software to calculate the state of energy in the system with the progress of mining along the entire length of each panel. The variation in the energy content of the model was monitored, and zones with potentially damaging slip-type events along bedding planes followed by compressive-type events in the sandstone roof are the mechanism for large seismic events in the studied mine. The locations of anomalous events corresponded to the regions where both compression-type SPI (C-SPI) and slip-type SPI (S-SPI) were elevated. The modeling results were compared with the recorded seismic events to evaluate the model performance in forecasting the seismic potentials. The model was able to forecast 100% of regions with elevated and moderate seismic potential and 89% of regions with low seismic potential. This shows the applicability of energy balance calculations for forecasting the approximate location and timing of destructive seismic events in advance of mining.

Jun 25, 2024