Search Documents

Acid mine drainage is still a common problem in the northern Appalachian high sulfur coal region despite mining and reclamation practices applied to control it. Mining companies must treat water with alkali to raise pH and precipitate metals in order to discharge the water into receiving streams. Common chemicals used to treat drainage are limestone, hydrated lime, soda ash briquettes, caustic soda, and ammonia. Each chemical has advantages or disadvantages under specific conditions. A simple spreadsheet program was developed to evaluate costs of treating acid mine drainage across several specified water quality parameters and time horizons. Caustic soda and soda ash were shown to be cost effective for treating low flows and low acidity over short time periods. However, as quantity of water increased, quality decreased, and time horizon increased, the ammonia and hydrated lime systems were found to be much cheaper than caustic soda.

Jan 1, 1991

By R. Harris, M. Misra

Column flotation technology has a demonstrated potential for recovering clean coal from high-ash waste fines. The effect of different variables such as air flow rate, frother addition, depressant addition, percent solids and particle size on the quality of separation are discussed. Results indicate that air flow rate and depressant addition are the important variables which control the selectivity in the flotation of fine coal in a column cell. Separation efficiency achieved with column cells is significantly better than that with conventional flotation cells. Under appropriate experimental conditions with a deep column, more than 80 percent coal can be recovered in the concentrate containing 10 percent ash from waste fines containing over 60 percent ash.

Jan 1, 1988

By E. D. Dainty, B. E. Enga, D. L. McKinnon

Following considerable laboratory studies concerning particulate control systems for underground use, a program was commenced to develop practical real life implementation systems. This program covers the implementation in seven mines of particulate filter systems to 10 engine models from three engine manufacturers in 12 different vehicle types, a total of 24 vehicles. As the program ran, one mine had to drop out and a mutually agreed upon system could not be arrived at for another. Hence, the program included five Canadian mining companies. Several of the vehicles trialed at Brunswick Mining were trialed by Brunswick themselves. Nonetheless, the data is presented. This paper covers the work performed from the beginning to the end of the demonstration program. Data collected to properly select and design filter systems along with technical conclusions of the demonstration are presented. Also presented are the results of a survey that highlights the participating mines' acceptance of the technology.

Jan 1, 1991

By Masahiro Lnoue, Kenichi Uchino

Airflow velocity vectors by a forcing auxiliary fan at a heading face were measured in an actual size model gallery and an actual mine. The location of an outlet of ventilation duct gives significant effects on the airflow at the heading in the gallery. It was also found that there were several stagnated regions which may have danger of methane accumulation. The flow were also examined using the visualization technique by laser light in a reduced scale model. The flow in reduced scale model showed similar behavior to those observed in actual size galleries. The air velocity at the outlet has no significant effect on the airflow. It was found that a region to be ventilated by the direct flow of the exhaust fan is limited to a relatively short distance but a secondary flow region is generated near the heading face. CFD ( Computational Fluid Dynamics ) method was also developed to examine the airflow. The calculated results coincides with those measured by actual and reduced scale models. It is concluded that the CFD is useful tool for the analysis of ventilation at the headings.

Jan 1, 1997

The sixth annual conference of the Mineral Economics and Management Society (MEMS) was held Feb. 27 through March 1 in Boulder, CO. This year's event was attended by more than 100 academic, industrial, government and other professionals interested in mineral economics and materials management. With about 250 members worldwide, this not-for-profit society seeks to promote scientific and economic analysis of current relevant issues. This year's program was sponsored by Alcan, Bateman Engineering, Cyprus Amax Minerals, J.P Morgan, Knight Piesold LLC and Newmont Gold. The conference's technical program consisted of six sessions. These included "Financial tools for a changing world," "Access to minerals," "Comparing North and South America," "Environmental issues in today's world" and "Transporting minerals." The program was concluded with a panel discussion titled "National minerals policies in Asia." In addition, a student papers session was held, in which students were given the opportunity to compete for a $1,000 award. The following is a brief review of the technical pro¬gram.

Jan 1, 1997

By V. Srajer

Operations research includes the application of systems analysis to mining operations, the acquisition of field data and the creation and verification of computer models of these operations. These activities result in the generation of computerized mine planning tools which have a firm base-in observational facts. The Surface Mining Laboratory of the Canada Centre for Mineral and Energy Technology (CANMET), in Devon, Alberta has been engaged in operations research activities since 1982. The work includes computer simulation of truck/shovel, continuous mining equipment and dragline operations. Other examples include cooperative programs with industry (such as the demonstration and evaluation of an integrated truck management system), the development of a device to measure off-highway truck rolling resistance, and an automated remote data transmission network. The presentation outlines existing and proposed research projects of the Operations Research group.

Jan 1, 1989

By George W. Toth

This chapter describes the development of a computer code which rapidly estimates the cost of producing coal from either surface or underground mining situations. The computer code, termed the coal production cost (CPC) code, was developed under an NUS corporate research grant and was based on the findings of several coal mining and cost research analyses performed by NUS over a three-year period. The studies which served as the primary basis for the CPC code were the coal mining cost models developed by NUS for the Electric Power Research Institute. These models were designed for use in manual analyses and have been published by EPRI (Toth, 1977; and Stinnett, 1977).

Jan 1, 1979

By P. Venkatasubramanian

The aerospace and nuclear industries have been applying systematic techniques for assessing the safety of complex technical systems for many years. These techniques such as fault tree analysis, failure mode, and effect analysis, etc., and more recently "expert systems," were developed to formally evaluate systems safety and to determine how hazards can he reduced. The application of formal methods such as expert systems has the potential for further reduction in both frequency and the consequences of mine accidents. This paper presents a general expert system model of diagnostic reasoning and describes its use as an inference method for analysis and problem identification for accidents due to the presence of an open cycle diesel-powered mine cars in underground coal mines.

Jan 1, 1987

By Yuanping Chen, Yihui Zhao, Yunhe Hong

It is important to study the methane transport phenomenon in a longwall panel under descentional ventilation conditions. The gob area is divided into a number of rectangular percolating elements, each of which is connected with its neighbors by leakage passages, so that a network can be formed. Using the mechanics of porous media fluid flow, the mathematical model of air and gas flows can be established. Based on the existing ground pressure theories, the inhomogeneous porosity of the porous media in the gob can be given. Through computer simulation it is found that air pressure and temperature are functions of position. Air density, viscosity, and natural ventilation pressure are functions of temperature, pressure and methane concentration. It is also found that the resistance varies with air density and viscosity. Finally, the calculation results are given to show the differences between ascentional and descentional ventilation methods.

Jan 1, 1991

By Nick J. Miles, Gareth J. Brown

The degree of fragmentation of dispersed systems of brittle materials such as pulverised rock has been described by a fractal dimension i.e. the fragmentation fractal. This fractal dimension represents a power law size-frequency distribution, where, in this case, the size is defined as the square root of the projected area. The existence of a fractal dimension for the number-size distribution, of the progeny of failure event, is direct evidence for scale invariance of the fragmentation process. Since a fractal dimension infers that failure mechanisms operate on all scales it has been suggested that the fractal dimension is a measure of the fracture resistance properties of materials during fragmentation. In order to investigate this a range of rocks of varying fracture toughness were broken under similar levels of impact velocity in the dynamic tensile failure of single particles. The fragmentation fractals determined from the resultant particle populations, of the breakage experiments, were monitored and are discussed.

Jan 1, 1995

By Joe W. Cotton, Thomas A. Wheeler

This paper briefly covers theories behind caking of crystalline salt particles, and methods of its prevention. The main factors that influence the extent of caking are humidity, storage pressure, temperature variations, and length of storage time. Careful adherence to control- ling these variables are more critical than the addition of even the most efficient anticaking reagent. The principle characteristics that a successful anticaking reagent must possess are: high retention at the temperature of application, good coating of reagent on the particle surface, capability of in- creasing the hydrophobicity of the particle, reducing the surface tension of liquids, and/or creating of a barrier between particles that prevent contact between particles, and modifying the crystal structure of the salt between the particles. Methods to evaluate the reduction of caking tenacity with the application of various anticaking reagents, reagent volatility and reagent degradation in plant and laboratory scales are discussed. Various types of anticake reagents used today in industry are organic active and inactive reagents, inorganic inert and inorganic salt crystal modifying re- agents.

Jan 1, 1986

By Iwao Iwasaki

Since the oil crises in the 1970s, the mining industry in the developed countries has faced strong competition from developing countries. In order for the North American iron ore industry to remain competitive with high-grade overseas sources, research on low-cost beneficiation methods that ensure high-quality and uniform-quality products must be maintained in order to prepare for ever-tightening specifications on iron making raw materials for blast furnaces and also for the future iron- and steelmaking processes that can directly utilize finely ground concentrates.

Jan 1, 1999

By C. K. Blair, V. J. Hucka, E. P. Kimball

In central Utah, a coal mining operation is taking place under an 0.5-m (20-in.) pressurized natural gas pipeline. The room-and-pillar method with pillar extraction is being used to extract the coal from the seams. The pillars beneath the pipeline will not be extracted; however, there is a possibility that some subsidence may occur due to pillar failure. To assess possible damages on the pipeline, an attempt has been made to predict subsidence in the area where pillars may collapse. The resultant values of subsidence strain and slope have been used to determine the magnitude of strain, stress, and shear induced in the pipeline. Also, a network of survey points has been installed along the pipeline to detect ground move¬ment that would indicate excessive subsidence.

Jan 1, 1987

By Y. M. Jiang, D. W. Park

Longwall faces can move at high advancing rates, but many geological variations can cause unexpected instabilities and production losses. The rapid movement makes it necessary to evaluate different geologic conditions in the rock mass as fast as possible to assess their effects on the longwall face and shields. It is believed that prompt awareness of geologic conditions is the key to preventing instability at a longwall face. This paper introduces the application of fuzzy set theory for characterizing and evaluating roof conditions. Real-time monitored data coupled with fuzzy set analysis provides valuable information, such as shield leg pressure, developing load on shields, intervals of periodic weighting and the ratio of developing loads during periodic to normal times.

Jan 1, 1998

By D. J. Cook, R. H. Fan, D. R. Maneval, Y-H. Shen

In this study, two placer mine processing plant effluent waters of significantly different characteristics were tested to determine the applicability of polymers along with other techniques to achieve reduced levels of turbidity. The waters from a Gilmore Creek mine and a Crooked Creek mine were characterized both as to their chemical and physical properties. The inorganic minerals were in large measure identified, and the principal cations were identified. The fine solids were studied as m their mineral identification and the extent of their electrical charges. Test work was done using polyrthylene oxide (PEO) and a liquid cationic polymer along with adjunct additives to determine optimum amounts of these coagulants for minimum consumption and optimum settling efficiency.

Jan 1, 1990

By Robert J. Watters, Peter C. Kelsall, Joseph G. Franzone

Two separate studies investigated the compressive strength of basic igneous rocks and its relation to index properties such as porosity, density and soundrave velocity. The rocks tested were weathered dolerite from S. W. England and vesicular lavas from California. In both cases strength was affected considerably by porosity. In the dolerite, strength was also affected by fissures (microcracks) which were formed in the parent rock by shearing and later accentuated by weathering. While test results show that porosity, density and sound velocity are not reliable indices of rock strength, these properties are useful in interpretation of strength test results. Index testing can be used to classify samples according to similar behavior and to recognize the influence of fissures.

Jan 1, 1986

By S. Saklar, i. Bayraktar

The effect of the feed size distribution on the kinetic parameters in pyrite flotation was studied. The kinetic parameters of the particular sizes were determined as a function of whether other particle sizes were present. From the data, a relation between the pyrite flotation rate and the particle size distributions was obtained. It was shown that the flotation rate constant (k) is a function of the size modulus (dt) of the Gates-Gaudin-Schuhmann distribution, and its variation may be expressed as k = a • exp(b . d,) for either individual size fractions or composite feed. Parameters a and b are dependent on the particle size distribution of the feed. Specifically, parameter a increases linearly as the distribution becomes coarser. The above relationship was also tested under conditions in which the collector (KAX) dosage was varied from 130 to 278 g/t. It was shown that the established relation was not dependent on the collector dosage.

Jan 1, 2002

By K. Rajamani, L. B. Hales

Much of the process control effort in the mineral industry uses proportional-integral-derivative controllers that require periodic retuning. Retuning hundreds of controllers typically employed in a single plant is a formidable task for the control engineer. Adaptive controllers offer an alternative to this problem, since they are designed to tune themselves. Four schemes of adaptive control-gain scheduling, model reference adaptive control, self-tuning regulator, and optimal adaptive controllers-are discussed with process examples. The control of a ball mill circuit with a multivariable self-tuning regulator is illustrated. This controller encompasses the advantages of the other three controllers and is applicable for a wide range of process variability.

Jan 1, 1988

By R. Bhaskar

Although the health effects of airborne dust in underground coal mines are well recognized, a lack of understanding remains about the fundamental mechanisms of dust generation, transportation, deposition and dust-lung reaction. This study was intended to contribute to the understanding of dust transportation and deposition mechanisms in underground mine airways. Data from in-mine experiments carried out under controlled conditions in a straight section of a longwall panel with three different airflow velocities and two different types of coal dust (bituminous and semi-anthracite) were used to determine the turbulent deposition rate of dust particles. Measurements of ambient dust concentrations and deposition along the mine airway were obtained and the total dust deposition velocity (rate) was calculated. The deposition velocity of turbulent diffusion was estimated based on the experimental data and theoretical equations. The effects of airflow velocity, particle size, particle density and distance from the dust source on gravitational, turbulent and total dust deposition are discussed along with related conclusions.

Jan 1, 1995

By Raj K. Singhal

This paper is a report on a task force study dealing with many facets of computerization. The primary mandate of the task force was to examine the software and hardware currently available for application relating to reserve estimation, mine planning, economic evaluation, equipment selection, production scheduling and composite mine simulation and to evaluate how adequately the software fulfills the user needs in surface mining of oil sands and coal. To meet its objectives the task force consulted extensively with the users, developers and suppliers of hardware and software. The paper outlines the approach taken by the task force to fulfill its mandate, summarizes its findings and presents some pointers which might be useful to others considering this type of evaluation.

Jan 1, 1986