Search Documents

By S. Budavari, F. M. C. C. Vieira

For several decades, the deep, gold-bearing reefs of the Witwatersrand basin have been mined predominantly according to layouts characterised by longwalls with strike pillars to provide regional support. During the past few years, a new generation of mining layouts has been introduced. These layouts are based on the concept of grid-type, scattered mining with dip pillars for regional support. As the extraction of the gold reefs extends to depths below 3500 m, the hazards associated with mining at these ultra-depths are expected to increase to unacceptable levels. Therefore, the question arises as to, which of the currently applied mining layouts is most acceptable for the economic and safe extraction of an ultra-deep orebody. The purpose of this paper is to describe a research investigation carried out to evaluate the degree of acceptability, from the rock engineering view point, of four currently used mining layouts for application at a depth-range of between 3500 and 5000 m. Pendant plusieurs décades, les filons d’or profonds du bassin du Witwatersrand ont été exploités d’une manière prédominante selon des dispositions caractérisées par des longues tailles avec des piliers directionnels pour donner un support local. Les dernières années ont vu la naissance d’une nouvelle génération de dispositions de mine. Ces dispositions sont basées sur le concept d’extraction type grille, éparpillée, avec des piliers au pendage pour le support local. Comme l’extraction des filons d’or va à des profondeurs en dessous de 3500m, il faut s’attendre à ce que les risques associés à l’exploitation à ces profondeurs extrêmes atteignent des niveaux inacceptables. Par conséquent, la question se pose de savoir laquelle des dispositions de mine couramment utilisées est la plus acceptable pour l’extraction rentable et sans danger d’un gisement ultra profond. Le but de l’étude présente est de décrire les recherches exécutées pour évaluer le degré d’acceptabilité, du point de vue d’ingénierie de roche, de quatre dispositions de mine couramment utilisées pour application à un rayon de profondeur entre 3500 et 5000m. Die tiefen, goldträchtigen Riffs des Witwatersrandbeckens wurden über einige Jahrzehnte hindurch vorwiegend nach jenen Layouts abgebaut, die von Langfrontstreben mit Schlagpfeilern charakterisiert waren, um regionale Unterstützung zu gewährleisten. Während der letzten Jahre wurde eine neue Generation von Grubenlayouts eingeführt. Diese Layouts basieren auf dem Konzept der Rasterfeld-Art, gestreuter Bergbau mit Neigungspfeilern für regionale Unterstützung. Es kann erwartet werden, daß auf Grund der Tatsache, daß sich die Extraktion der Goldriffs auf Tiefen unterhalb 3500 m verlagert, die Gefahren, die mit dem Bergbau an diesen Ultratiefen verbunden sind, sich auf ein nicht annehmbares Niveau erhöhen. Folglich erhebt sich die Frage, welche der gegenwärtig angewendete Abbaulayouts für die ökonomische und sichere Extraktion eines ultra-tiefen Erzkörpers am annehmbarsten ist. Zweck dieser Arbeit ist es, eine durchgeführte Untersuchung zu beschreiben, die vom Gesichtspunkt der Gesteinstechnik gesehen, vier gegenwärtig angewandte Abbaulayouts für den Einsatz in einem Tiefenbereich zwischen 3.500 und 5.000 m evaluiert.

Jan 1, 2003

By T. Feroze, B. Genc

"Blind headings in room and pillar coal mines are a major source of methane and coal dust. Most methane and coal dust explosions therefore occur in the blind headings. The primary cause of these explosions is the disruption of the local ventilation system. Line brattice (LB) ventilation systems are used to ventilate blind headings by directing air from the last through road (LTR) into the heading. The amount of air available to ventilate the face of the empty heading depends on the heading dimension, settings of the LB, and velocity of air in the LTR. LBs are commonly installed by underground supervisory staff based on work experience, which may result in ineffective ventilation. The correct installationof LBs remains a challenge. In this study, a validated computational fluid dynamics (CFD) model has been used to analyse the effect of the LB ventilation system variables on the air flow rates close to the face of the empty heading. Full-scale three-dimensional models with various heading heights, heading depths, LB settings, and LTR velocities were simulated. The air flow rates and patterns at various locations inside the heading were analysed. A comparative study was carried out to quantify the effect of each of these system variables on the flow rates close to the face of the heading. Based on the findings, a user-friendly numerical model was formulated that can be used to estimate the flow rate close to the face of an empty heading for different practical settings of the system variables. This model can help the supervisory staff to swiftly implement the ventilation plan according to the regulations and the mine standards. The model can also serve as part of the curriculum for educating future mining engineers."

Jan 1, 2017

By T. Feroze, B. Genc

"Blind headings in room and pillar coal mines are a major source of methane and coal dust. Most methane and coal dust explosions therefore occur in the blind headings. The primary cause of these explosions is the disruption of the local ventilation system. Line brattice (LB) ventilation systems are used to ventilate blind headings by directing air from the last through road (LTR) into the heading. The amount of air available to ventilate the face of the empty heading depends on the heading dimension, settings of the LB, and velocity of air in the LTR. LBs are commonly installed by underground supervisory staff based on work experience, which may result in ineffective ventilation. The correct installation of LBs remains a challenge.In this study, a validated computational fluid dynamics (CFD) model has been used to analyse the effect of the LB ventilation system variables on the air flow rates close to the face of the empty heading. Full-scale three-dimensional models with various heading heights, heading depths, LB settings, and LTR velocities were simulated. The air flow rates and patterns at various locations inside the heading were analysed. A comparative study was carried out to quantify the effect of each of these system variables on the flow rates close to the face of the heading. Based on the findings, a user-friendly numerical model was formulated that can be used to estimate the flow rate close to the face of an empty heading for different practical settings of the system variables. This model can help the supervisory staff to swiftly implement the ventilation plan according to the regulations and the mine standards. The model can also serve as part of the curriculum for educating future mining engineers."

Jan 1, 2017

By C. P. Smyth

Large volumes of quantitative geochemical data, presenting a formidable interpretation task to geologists, are generated in the course of exploration drilling for new ore deposits. The incorporation of geological expertise into computer programs developed for the interpretation of this data would improve the speed and accuracy with which it is interpreted. A detailed analysis of the geochemical log interpretation problem, together with a survey of relevant research in Artificial Intelligence and petroleum well- logging techniques, confirms, that artificial intelligence, particularly as developed in the fields of expert systems and pattern recognition, provides techniques for implementing such data interpretation programs. In addition, it provides data analysis techniques significantly more powerful than those currently applied to geochemical data, and very appropriate to the hypothesise and test' character of mineral exploration problem-solving. The conversion of raw borehole log data to meaningful higher level geochemical entities, in terms of which geological reasoning may take place, is a critical step in applying these techniques to log data analysis. A method of achieving this conversion as an exercise in signal-to-symbol transformation is presented.1

Jan 1, 1987

By N. B. Strydom, H. H. E. Schroder, A. van der Linde

This paper describes a study of the destination of the mercury that is present in the ore during the recovery of gold. It was found that over 96 per cent of the mercury passed through the process untouched. A small amount finds its way into cyanide solution, and is concentrated with gold in Zinc dust as Merrill precipitate. When the precipitate is calcined, the mercury is driven off and finds its way into the atmosphere. However, dilution of the stack gas in the atmosphere appears to be sufficient to prevent hazardous concentrations arising at ground level. No other significant concentrations of mercury were found at any stage of the process. The amount of mercury lost to the atmosphere by this mechanism appears to be less than 200 kg per year throughout the gold-mining industry in South Africa. Virtually no mercury vapour could be detected in the air in the smelt-house. Slight increases in mercury concentrations above background level were observed in soils around the reduction plants and in the discharge or return waters, but no environmental stress is anticipated from these increases.

Jan 1, 1982

By R. I. Klintworth

The multi-reef area of Cooke 3 Shaft provides a unique mining challenge on account of the very thin middlings between the pay bands and the marginal values of the reef. It is uneconomic or impractical, because of the excessive heights, to mine the middlings using conventional stoping methods. The development of suitable mining methods is discussed with particular emphasis on the control of water inflow and the policy of not jeopardizing or sterilizing other reef horizons by the mining method implemented. No definite solution is currently available, but with the aid of instrumentation, computer analyses and mechanized mining equipment, the mine continues to attempt to maximize extraction and profits.

Jan 1, 1988

By S. Duma

The main sulphide zone (MSZ) of the Great Dyke is cryptic and without obvious stratigraphic markers. Although there are trends in the dimensions of the PGE and base metal profiles across the Hartley Complex, the profiles are invariant within a particular mining area. Ratios derived from these profiles are used to interpret diamond drill cores drilled ahead of underground development. Detailed logging of oriented core shows the exact position and attitude of intersected faults. Metal ratios are used to estimate fault throw to within 25 cm. It is possible to draw detailed sections showing the extent of ground disturbance well ahead of mining. The method has been confirmed by mining and by drilling inclined holes through the fault blocks. Keywords: main sulphide zone, Hartley Complex, Great Dyke, Zimbabwe, platinum, Palladium, Nickel.

Jan 1, 2004

Outotec?s direct leaching process is an atmospheric leaching process for sulphidic zinc concentrates. The direct leaching process, based on special leaching reactors developed by Outokumpu, is the most economical way to produce electrolytic zinc. The production scale applications of the process realized so far are in use at Boliden?s Kokkola and Odda zinc plants. A new full-scale application of Outotec?s direct leaching process will be started in 2008 in China. The process is integrated into the existing production plant, replacing part of the old production facilities by modern technology. Besides high zinc extraction the plant expansion and modernization offers also indium recovery, iron precipitation and solution purification processes. The process equipment includes tailor-made reactors designed on the basis of the work and experience of Outotec research centre. Keywords: zinc, concentrate, atmospheric leaching, technology, indium, iron precipitation, solution purification, Outotec.

Jan 1, 2008

By E. Minnaar, P. J. Cilliers, M. Bellino, L. M. Roux, R. Dye

The classic technique to remove impurities in a cobalt stream is selective precipitation. This is usually followed by re-leaching to produce an advanced electrolyte for cobalt electrowinning. Although this technique ensures an adequate cobalt concentration in the electrowinning circuit, some of the consequences include unwanted losses through the numerous selective precipitation steps resulting in lower recoveries. One plant that currently utilizes selective precipitation is the Luilu Metallurgical Plant (Luilu) in the Democratic Republic of the Congo. This paper evaluates the benefits of using solvent extraction technology as a purification step in the Luilu Process with the aim of further increasing the overall cobalt recovery and to ensure that a suitable cobalt concentration in the advanced electrolyte is achieved. The implementation of a solvent extraction-electrowinning process is found to be beneficial in terms of achieving improved recoveries and cobalt cathode quality, however there are many other factors that impact the success of converting from the classic precipitation process used at Luilu.

Jan 1, 2007

By D. J. Mourant

Day-to-day operations on the Broken Hill mine of the Black Mountain Mineral Development (BMMD) Company require a detailed knowledge of the distribution of the ore minerals within the orebody. The data are acquired by systematic underground diamond drilling of the orebody and subsequent geological and analytical borehole logging. These data are then captured onto a database, available for further analysis. Before mining commences in a mining block, copper, lead, zinc, silver and bismuth assay values, and the specific gravity of each sample, are extracted from the database. 3-dimensional variogram and kriging calculations are performed for each geological zone; for all the metals of interest. A computer representation of the mining block in the form of an ore model is then built using these kriged data. From these ore models information is extracted as required by the Geology Department on the mine, and used in numerous operations. These include: daily grade control to supply optimum feed grades to the treatment plant; the compilation of short, medium and long term production schedules; orebody outline definitions for the detailed planning of mining operations; ore resource calculations. The system has been modified and updated since its inception and provides timely information in a production environment.

Jan 1, 1987

A dual rate kinetic model consisting of differential equations is used to describe the kinetics of the adsorption of gold cyanide on activated carbon. The partial differential equation describing the material balance in the liquid phase is written for the special case of a fixed bed system. It is shown that an isotherm for the case of a closed system is required to yield accurate simulations of the equilibrium in a column of activated carbon. Whereas the equilibrium loading of gold cyanide is influenced by the free access of oxygen to the system, the traditional open batch stirred tank experiments, which are used to estimate parameters for the calculation of breakthrough curves for organic solutes, cannot be used here. The program solves this model at incremental heights in the column at a specific future point in time. Runge-Kutta and backwards- difference methods are used in the numerical solution. A Von Neumann method is used to show that the solution is stable. Kinetic parameters can be estimated either from batch experiments or from short column runs. In the latter method the column should not be long enough to contain the concentration wavefront for the system of interest. Results obtained from bench scale continuous column experiments were used to verify the computer model. Pure gold solutions as well as real leach liquor were used in both short column and countercurrent moving bed experiments.

Jan 1, 1987

By R. L. Robinson

An analytical framework is formulated to assist mining companies in assessing the relative merits of mineral exploration and acquisition strategies. The anticipated costs, risks, and returns of each strategy are conceptualised using decision trees. Economic criteria - expected net present value, expected return per unit of investment, and the probability of success - for each strategy are derived(from the appropriate decision tree network. Application of the analytical framework is illustrated using the example of a medium-size company in the Canadian base metal sector.

Jan 1, 1987

By H. Gumede

The challenges of noise emission in the mining industry are well known. These challenges are exacerbated by the increasing trend towards mechanized mining, and there is general consensus that an effective industry-wide Buy Quiet initiative (BQI) will significantly assist in reducing noise-induced hearing loss by minimizing noise at its source. In its endeavours to improve the health of workers, the MOSH Noise Team has facilitated development of a proposed strategy and structure for a BQI. Extensive consultation with stakeholders resulted in support for the initiative. The MOSH Noise Team was advised to solicit the contributions of consulting mechanical and electrical engineers (CM&EEs), whose support is viewed as critical for realization of the initiative, since elimination of noise at source is an engineering challenge, and most procurement standards and specifications are set and managed by engineers. A workshop with CM&EEs and their representatives, as well as group environmental engineers (GEEs), confirmed the urgent need for the initiative and provided valuable insights. The workshop used obstacle based planning techniques to identify the factors on which the success of this BQI will depend. Most potential obstacles to the implementation revolved around proper scoping, leadership commitment, and companies? adherence to the initiative. Lack of involvement by the relevant stakeholders and economic issues were also identified as potential obstacles. Delegates at the workshop felt that the successful implementation of the industry-wide BQI, will depend on the mining industry addressing the specific obstacles. The most critical and urgent issue was identified as the formation of a properly constituted industry-wide BQI task team that includes representatives from critical stakeholder groups and which is mandated and empowered to drive the initiative.

Jan 1, 2014

By F. Riedel

In May 2009 a test work programme was carried out at the sorting laboratory of CommodasUltrasort in Germany which was aimed at establishing the efficiency of X- ray transmission sorting for the recovery of unliberated diamonds in a size range of +8mm. A PRO Tertiary XRT belt sorter with a working width of 600mm and a belt speed of -3mJs was used for the test work. Dual energy X-ray transmission sorting is a type of sensor-based sorting which uses an X-ray scanning system, The attenuation of the transmitting X-rays is measured at two different energy levels, Thereby it is possible to eliminate the effect of the particle thickness on the measurement result. The effective measurement results in a classification by elemental order based on the periodic table.

Jan 1, 2010

By E. E. Almási, G. Mucsi, G. Rákhely, Á. Rácz, B. Csőke, Zs. Pap, K. Bohács, N. Halyag

Wet stirred media milling is a widely applied grinding process in the field of mineral processing to produce <10 μm ground materials. In this paper, the results of wet stirred media milling of different Ti, Fe and Cu-oxide and phosphate minerals are presented. During the experimental work, grinding of ilmenite, vivianite, hematite and cuprite was carried out in a continuous operation wet stirred media mill. During the experiments, the particle size distribution and specific surface area of the ground materials were determined after a certain grinding time, as well as measuring the specific grinding energy, thereby determining the grinding kinetics of the different minerals. The measurement results showed the differences and similarities in the grindability of the individual minerals. Nano particulate vivianite, hematite and ilmenite was successfully manufactured in a stirred media mill; however cuprite was characterised as the coarsest final product for the same grinding circumstances. Keywords: Wet stirred media mill, cuprite, vivianite, ilmenite, hematite

Jan 1, 2020

By H. E. Bartlett

This paper deals with the sampling and mass measurement for ore delivered from a shaft to a processing plant and the contribution of the data from these measurements to the metal balances from shaft deliveries to final metal production. Accurate measurement of the grade and tonnage of run-of-mine ore is important for four main reasons; ? It enables the measurement of the production from different profit centres to within statistically determined confidence limits for daily, monthly, or annual averages. The profit centres could be individual shafts within a mining complex or ore treated on a toll basis ? The monthly production at shaft head is compared to the grades and tonnage determined from underground sampling and mass measurement in terms of a shaft call factor ? The sum of the production from the shafts is the input to concentrators. This input is a major part of the total input into a complex with concentrators, smelters, and refineries. In terms of the Codes of Practice for Metal Accounting the inputs are compared to outputs and inventory changes to assess the efficiencies and unaccounted losses or gains at the various stages in the flow of metal from source to market ? On a daily or daily moving average basis, the grades and tons from shafts are monitored and compared against these quantities from underground measurements. This acts as a control on off-reef mining, dilution, and other factors underground. Accurate measurement of grade of ore at the shaft head has been a challenge because of the large particle size. The conventional wisdom has been that ore can be sampled accurately only after it has been milled to give a slurry that is sampled as feed to a flotation process. However, when the ore fed to a flotation plant comes from multiple sources each source has to be sampled separately. So, relying on the grades determined using the sampling of concentrator input with cross-stream slurry samplers is not an option for determining the grade from an individual shaft. Impala has developed a system for sampling and weighing run-of-mine ore from multiple shafts. The system involves sampling the inputs to the plants using cross-belt (hammer) samplers and weighing the deliveries using in-motion railway weighing systems. Many samples are taken. Individually they have a high variance but, as a consequence of the averaging effect of large numbers and as shown by statistical analysis, the mean results are fit for the purposes of daily grade control for shafts and for monthly accounting of production from individual shafts. In the metal accounting systems at Impala, the measurement of input, including ore and toll-treated material is compared to the output in the form of final metal and tailings losses, as well as any inventory change that takes place, in order to determine a final metal balance from mill feed to product. The calculated inventory is compared to that measured, and the difference, or unaccounted- for metal, is then reported as a percentage of input. The balances obtained over several years yields balances for platinum that are below 1% imbalanced. Keywords metal balancing, platinum mines, AMIRA codes of practice, metal accounting, sampling, run-of-mine ore, statistical analysis.

Jan 1, 2014

By P. G. Toledo, R. I. Jeldres, G. R. Quezada

Chile is the main producer of copper in the world and lately the mining industry has suffered challenges due to the lack of water in the north of the country, along with the new policies of not using fresh water for the industry. This has prompted the use of seawater as an alternative source for mining. Several studies have been driven due to this new scenario, which have shown that seawater can be beneficial, if certain ions are removed from the process. This is the Mg that generates precipitates at high pH, that have been shown to make mining operations difficult. In particular, thickening operations are impaired by the presence of Mg ions, where aggregate formation and sedimentation decreases substantially. Our studies suggest the competence of the precipitates in adhering to the polyacrylamide (HPAM) flocculant and not towards the surface of the quartz minerals. This motivates the present work to use molecular dynamics to study the adsorption of a HPAM molecule on quartz surfaces and the surfaces formed by Mg precipitates. The surfaces are immersed in a saline solution or seawater that includes the HPAM molecule. Results are obtained by measure the adsorption frequency and duration. We obtained that the HPAM molecules are preferably absorbed on the surfaces of magnesium hydroxide. This gives us a good agreement with what is observed experimentally and strengthens the premise of the competition of hydroxide with the flocculant. Keywords: Molecular dynamics, adsorption, tailing flocculation, magnesium removal

Jan 1, 2020

By J. W. van der Merwe

Technology is advancing at a rate that makes it extremely difficult for the mining industry to keep pace. Many advances occur within a given piece of technology and often this is missed by the disciplines that could have gained advantage by its implementation. Often this may have been simply an aspect of cost exceeding benefit. However, there are some technologies that potentially have such a far-reaching impact on the mining industry that the benefits simply outweigh the cost. The application of 3D laser scanning in the mining industry has the potential of taking the concept of &apos;Google maps?&apos; underground. This presents an opportunity where the virtual world of underground can be traversed with relative ease and many aspects of measurements could be obtained without having to visit the working place again, potentially saving countless man-hours and still delivering precision work with significant savings in downtime, stoppages, and exposure to safety incidents. Anglo American Platinum maintains its competitive advantage though the review and application of appropriate technology. This paper describes the 3D laser scanning trial at one of Anglo American Platinum&apos;s new shafts, and goes on to show the benefits encountered through the application and the involvement of the various MRM disciplines.

Jan 1, 2013

By Y. Zhang, F. Zhu, Y. Zhao, L. Dong, Y. Li

In order to obtain a more suitable separation medium for fine coal, in this paper a pulsed fluidised bed was used to measure the pressure fluctuation, density characteristics, bubble diameter and rising velocity of Geldart A and B particles in the bed by controlling the pulsation frequency and gas velocity, in order to study the fluidisation effect and two-phase distribution of the bed. The results indicated that with the increase of pulsation frequency, the breakthrough point on the fluidisation characteristic curve caused by particle adhesion disappeared, and there was an optimal frequency, which made the minimum fluidisation velocity of particles reach the minimum. In addition, the bubble rising velocity was also simulated. The relationship between them was established using a model, and the error was within 5%. This provides an effective way to predict the bubble velocity, study the distribution of bubble phase, and improve the stability of bed density. Keywords：Frequency, flow velocity, pressure fluctuation, bed density, bubble

Jan 1, 2020

By M. H. Tyeb, C. Banerjee, A. K. Majumder

The primary requirement from a hydrocyclone is the classification of the feed solid particles. Particle classification occurs inside a hydrocyclone by virtue of the relative radial distribution of the suspended particles, based on their size and specific gravity. The particle classification behaviour in a hydrocyclone is experimentally studied in this paper. The phenomenological features of the air core at different feed solid concentrations and the distribution of the solid concentrations in the hydrocyclone are also analysed by the theoretical study of flow features in a steady Rankine vortex. Semi-empirical models for predicting the hydrocyclone performance in terms of flow split ratio, and cut size have been developed using the background knowledge of convoluted hydrodynamics. In addition, to validate the classification performance of a smaller diameter hydrocyclone, the potential of the present model is extended for envisaging the same for larger diameter hydrocyclones. A comparison between the model predicted values and the measurement data shows a good match. Keywords: Hydrocyclone, classification, Rankine-vortex, air core, modelling

Jan 1, 2020