Search Documents

By C. R. S. Needes, M. J. Nicol, G. T. W. Ormrod, N. P. Finkelstein

The industrial application of a dioxide electrode uranium by C. R. S. NEEDES, Ph.D. (London) (Visitor), M. J. NICOL, Ph.D. (Rand) (Visitor), N. P. FINKELSTEIN M.Sc. (Rhodes), Ph.D. (Liverpool) (Fellow), and G. T. W. ORMROD (Visitor) A correlation between the potential of a U02 electrode and the rate of recovery of uranium has been proved in laboratory and plant trials. When the recovery rates change because of variation in the concentrations of Fe(III), Fe(II), SO4 'and H+, a positive correlation is observed. However, an 2- increase in the concentration of phosphate in solution produces an increase in the U02 electrode potential but a decrease in the rate of leaching of U02. The correlation between the U02 electrode potential and the rate of leaching of U02 is then negative. It is concluded that, as a control device, the electrode cannot compete with the platinum electrode for use on certain plants. Nevertheless, the U02 electrode will act as a useful warning device if the total concentration of iron in solution decreases to below a level concomitant with the economic recovery of uranium. Furthermore, because of the positive correlation between the U02 electrode potential and the phosphte concentration, the electrode will also be of value in the detection of an increase in the phosphate level in solution. When it was incorporated in a suitable industrial probe, the electrode was found to be able to withstand the rigours of the leaching conditions in a large pilot-plant pachuca, and only failed after six weeks' operation.

Jan 11, 1975

By G. G. Rogers, A. Vna Der Linde, N. B. Strydom, W. H. Van Der Walt

Changes in the level of serum vitamin C in mineworkers by N. B. STRYDOM, M.Se., Ph.D. (Illinois) (Fellow), G. G. ROGERS, M.Se. (Pta) (Visitor), W. H. VAN DER WALT, B.Se. (Poteh.) (Visitor), and A. VAN DER LlNDE, B.Se. (O.F.S.) (Visitor) The levels of serum vitamin C in the blood of mineworkers were determined on the first and fifth days of the normal heat-acclimatization period (i.e., before and after exposure to heat) and again after I, 2, and 4 months of underground employment. Supplementary vitamin C was administered to the men during the heat-acclimatization period. Six groups of 20 men featured in the study and, except for one of the two 4-month groups, all the values were obtained after a full shift of underground work. It was found that adequate levels of serum vitamin C were maintained during the heat-acclimatization period, and the 250 mg of vitamin C given daily to each man must therefore be regarded as sufficient. The serum vitamin C decreased significantly with time of exposure to underground conditions, showing that the vitamin C utilized during heat stress is more than that provided in the men's diet. At the end of 4 months, not a single subject had more than 0,4 mg of serum vitamin C per 100 ml, most of them having only 0,3 mg per 100 ml; 90 per cent of the men had had more than 0,4 mg per 100 ml during the acclimatization period. It is therefore recommended that the mineworkers' diets should be supplemented with 100 to 200 mg of vitamin C per man per day.

Jan 5, 1977

2nd CONGRESS OF THE INTERNATIONAL SOCIETY FOR ROCK MECHANICS The 2nd Congress of the International Society for Rock Mechanics will be held in Belgrade, 21-26 September, 1970. The Congress will include: working sessions, study tours, receptions, excursions introduced in the working sessions and post-congress excursions and special programme for accompanying persons. Anyone interested in rock mechanics and its applicarion may take part in the 2nd Congress. Official languages of the Congress are: English, French and German. Simultaneous translation service will be provided during the Congress. All the correspondence concerning the 2nd Congress of the International Society for Rock Mechanics should be addressed to: Sekretarijat 2. kongresa Medjunarodnog drustva za mehaniku stena Institut za vodoprivredu "Jaroslav Cerni" Bulevar vojvode Misica 43, Postanski fah 530 Beograd - Jugoslavija NINTH INTERNATIONAL SYMPOSIUM TECHNIQUES FOR DECISION MAKING IN THE MINERAL INDUSTRY The Symposium which is to be held in Montreal during the week of June 14-19, 1970, follows the Computer Symposium held in Salt Lake City this year. The purpose of the Symposium is to define the role of decision making techniques within the mineral industry and to stimulate the development of specific applications. The subject of the Symposium-mathematics, operations research and computers as applied to the mineral industry-allows a complete picture of the mineral industry in its public policy, corporate, financial and technological environment to emerge. This is another of the series of symposia on this and related subjects started in the early 1960's at the University of Arizona. Sponsorship has included a number of Universities and the Society of Mining Engineers of the American Institute of Mining. This 1970 symposium is the first to be held outside of America, and is being sponsored by the Canadian Institute of Mining, McGill University and Ecole Polytechnique. A number of delegates from South Africa have participated in these symposia and several have already arranged to attend this symposium in Montreal. Enquiries should be directed to: Secretariat, The 9th International Symposium, Department of Mining Engineering, Ecole Polytechnique, P.O. Box 50l, Snowden, Montreal 248, Quebec, Canada. 24th INTERNATIONAL GEOLOGICAL CONGRESS This Congress is to be held in Montreal, Canada, from August 21 to 30, 1972. A very detailed and extensive programme has been proposed, and includes a number of excursions. Copies of the first circular are obtainable from: The Organizing Committee, 24th International Geological Congress, 601 Booth Street, Ottawa 4, Ontario, CANADA. SYMPOSIUM ON THE RECOVERY OF PYRITE The proceedings of the Symposium on the Recovery of Pyrite, held in Johannesburg on 12th to 13th June 1969 are now available. Copies may be ordered from the Secretary, S.A.I.M.M., P.O. Box 61019, Marshalltown, Transvaal at a cost of R10.00. Papers and addresses presented at the Symposium were: Opening Address by Mr J. K. E. Douglas (President). 'The world sulphur position,' by W. C. J. van Rensburg (Member). 'The South African sulphur position,' by D. L. Taylor (Member). 'The recovery of pyrite at Government Gold Mining Areas Limited,' by R. J. Westwood (Member), G. S. Stander (Affiliate) and H. R. Carlisle (Member). 'Recovery of pyrite concentrates from colliery-waste discards-A preliminary assessment,' by W. A. Gilbert (Visitor) and E. A. Nugent (Member). 'The role of pyrite in upgrading the uranium content of Witwatersrand conglomerate ores by means of the heavy-medium separation process,' by D. J. Tutt (Associate Member). 'Pyrite recovery by jigs at Durban Roodepoort Deep Limited,' by E. J. Dominy (Affiliate), F. Diamond (Affiliate) and A. D. Graham (Affiliate). 'The storage of pyrite concentrates,' by Joan C. Campkin (Visitor) and P. J. Lloyd (Member). 'The flotation plants of the Anglo- Transvaal Group,' by L. A. Bushell (Member). 'Pyrite flotation with amines and cyanidation of the products,' by E. H. D. Carman (Member). 'Gold recovery by cyanidation from mill products obtained after pyrite flotation,' by P. G. Mrkusic (Graduate), M. Sciarone (Visitor) and H. E. Simonsen (Visitor). 'The influence of sulphydral and cationic flotation reagents on cyanidation of native gold,' by K. G. Ashurst (Visitor) and W. P. Finkelstein (Member). 'Laboratory tests on the flotation of pyrite from Witwatersrand gold ores by cationic collector,' by J. Levin (Member), and M. L. Veitch (Visitor). Closing Address, by Dr R. E. Robinson (Director, National Institute for Metallurgy).

By A. Kotze, D. Messina, E. Nagels, Y. Cryns, S. Arnout

The FlashPhos process aims to recover white phosphorus (P4) from sewage sludge by drying, flash combustion/gasification, and carbothermic refining steps. This study evaluates the material behaviour of sewage sludge ash melting and reduction in a refining furnace for the novel FlashPhos process. Thermodynamic modelling in FactSage 8.2 is combined with experiments from a tube furnace to determine the possible phosphorus recovery and minor element behaviour. For the two studied sludges, a yield of 40% and 75% white phosphorus is achieved after 1 hour at 1600°C, corresponding with a 60% and 25% loss to the metal phase. This is slightly above the calculated equilibrium yield of 28%–73%, which depends mainly on the Fe/P ratio of the sludge. Temperature is found to have a significant influence on the final phosphorus yield when leading to incomplete melting of the ash. A clean slag is produced in the process free of heavy metals making it suitable to be used as a cement-like binder material. The main heavy metals that co-evaporate with the phosphorus are Zn, Pb, As, Sb, and Sn. Additional processing steps will be required to remove these to produce a pure P4 product. The metal alloy consists of mostly Fe and P with smaller amounts of other components such as Mo, Cr, Cu, Mn, Sn, Sb, and V. The final slag consists of CaO, SiO2, MgO, and Al2O3 with virtually complete removal of P and heavy metals.

Oct 2, 2025

By B. G. Meyburgh

E. H. D. Carman: The results achieved at Buffelsfontein Gold Mining Company Limited are very encouraging and it seems certain that as far as the conventional uranium recovery process is concerned solvent extraction must entirely supplant the old resin ion exchange process. The operational costs given by Mr Meyburgh indicate that the chief cost items in solvent extraction are reagents. In other words 38.4 per cent of the operational cost at Buffelsfontein is due to the replacement of the organics lost from the plant. It is reported from a wide field of experience that loss, particularly of amine, is a direct function both of the quantity and nature of finely divided suspended solids in the pregnant solution and the extent to which the design of the mixers causes the formation of secondary dispersions which do not easily separate in the settler. There is in addition the unavoidable loss of amine due to its solubility in the aqueous solution which is thought to be about 4 p.p.m. In order to minimise solvent losses therefore, efficient clarification at the head of the solvent extraction plant would appear to be a most important requirement. For this reason the newly erected plant at West Driefontein Gold Mining Company Limited has two Funda Pressure Filters each with a filtering area of 540 sq. ft. which are together designed to handle up to 440 g.p.m. of filtrate. This plant has not yet been commissioned but preliminary testing indicates that suspended solids in the sub micron size range which do not settle even on protracted standing of the solution, will rapidly blind the clarifiers. This should not affect solution clarity but frequent backwashing adds to the cost of precoating. The difficulty was countered in the laboratory with continuous additions of filter aid in addition to the precoat but, as Table 11shows, cost of filter aid is high and its use will have to be optimized against organic losses due to less efficient clarification. This will need much careful observation over a relatively long period of time. Costs shown in Table 11 are based on Mr Meyburgh's figures adjusted to probable conditions at West Driefontein Gold Mining Company Limited. The assumption based on small scale testing is that it will cost 5.2c/ton in filter aid to clarify filtrate to a level of about 5 p.p.m. of suspended solids, in order to restrict the amine loss to 10 p.p.m. which is likely to be equivalent to an entrained organic loss worth approximately only 2.6 cents per ton. Of course poor clarification as mentioned earlier is only one of two or even more causes of organic losses and it seems obvious on the above basis that the operation and economics of pressure clarification will need close investigation. A second important consideration at West Driefontein has been the design of the pump-mixers which must perform the dual function of phase mixing and providing the necessary hydraulic gradient for counter current flow of the two phases. The arrangement is shown in Fig. 1.

Jan 10, 1970

By D. A. Phillips

A procedure for designing an optimum pit to yield maximum profit is described. The volume in which a possible pit is considered is divided into discrete blocks, each of which is assigned an economic value equivalent to its worth as a block of mineable material. The profitability of a pit can then be generated by summing the blocks within the pit. The optimizing procedure starts at the surface level and proceeds downwards level by level, to obtain the optimum pit at each level. The method makes use of the fact that an optimum pit at a particular level must be completely contained in any optimum pit at a lower level. Procedures for generating block costs, and pits with various slope angles under the restriction of complete block removal are considered briefly. The main description is of the theory of the method and the computer program based on this. The method is applicable to any type of mineral deposit, the only requirement being that the orebody should be represented accurately by a block model.

Jan 1, 2014

The January General Meeting of the Institute was held in Kelvin House, Johannesburg, on 15th January, 1969 at 4.30 p.m. Mr R. C. J. Goode (President) was in the Chair. There were also present eighteen Members, including Messrs F. P. Bath, H. Britten, J. K. E. Douglas, P. Lambooy, V. C. Robinson, W. T. Stobart and P. W. J. van Rensburg (Council Members), Messrs J. C. Hall, P. C. Pirow, Dr D. I. Legge, Messrs E. R. Rudolph, H. R. Reid, Dr N. Stutterheim, Messrs B. F. van der Merwe, L. W. P. van den Bosch, D. T. Watt, M. Youngworth and T. Zadkin. Two Associate Members, Dr P. R. Jochens and Mr D. A. Viljoen. Two Students, Messrs R. P. W. Henrard and D. Ossin. Sixteen Visitors, including Messrs I. Barnes, B. F. Bath, S. Botha, P. A. du Plessis, K. Edwards, Dr F. S. Fulton, Messrs H. Grant, B. Havenga, L. Kok, Dr D. Lasar, R. Sandler, C. W. Wolhuter and J. D. Young. Secretary, Mr D. C. Visser. Total present: Forty. MINUTES The President: "May we confirm the minutes of the meeting held on the 20th November, 1968, as published in the December, 1968, issue of the Journal?" Agreed. MEMBERSHIP The President: "I have much pleasure in announcing that the names of the under-mentioned candidates, having been published in accordance with By-Law 5.2.2, Council has elected them to membership of the Institute in the following grades: Members: Basil James Jackson and James Petrie Archibald. Associate Members: Ronald Creasy, Hugh Angus McCallum and John Barton Cunliff. Graduate: Hermanus Isak Johannes van der Merwe. Affiliate: Edgar Ramsay. Student: Petrus Daniel Wolmarans. MEMBERS TRANSFERRED TO A HIGHER GRADE From Affiliate to Associate Member: Neil Bradfield and Mervyn Bayard Allman. "I welcome the newly elected members to the Institute and congratulate those members who have been transferred to a higher grade." (Applause). GENERAL BUSINESS The President: "Are there any matters to raise under this heading? If not, we will proceed to the next item on the agenda which is the presentation of today's paper."

By E. R. Leeman

INTRODUCTION The first references in the literature to the so-called C.S.I.R. 'doorstopper' strain cell were made in 1964 1,2,3,4. These were the climax of nearly two years of experimental and developmental work with the instruments and the operating techniques involved. Since that time numerous field measurements have been made with 'doorstoppers' and they have been developed to a stage where they are in commercial production and are being supplied to users throughout the world. No detailed description of the latest 'doorstopper' equipment has, however, appeared in print and this paper is written to bring the literature up to date in this respect. The triaxial strain cell was developed three years ago 5, 6, 7 and was first described at the First Congress of the International Society for Rock Mechanics in Lisbon in 1966 8. Since that date laboratory tests and-particularly important-field tests 7' 9 have demonstrated the validity and practicality of the instruments and techniques. These instruments have also been developed to a stage where they have been released for commercial production. In this form they are very different from those described two years ago and a full description of them at this stage seems to be justified. THE INFORMATION SUPPLIED BY 'DOORSTOPPER' AND TRIAXIAL STRAIN CELLS Both the 'doorstopper' and triaxial strain cells were designed specifically to determine the absolute stress in rock using an overcoring stress relieving technique. They were not designed to measure changes in stress. They may, however, be used for the latter purpose provided the glue which is used to stick the strain gauges to the rock is known to possess sufficiently stable strain-time characteristics as not to affect the accuracy of the results during the time the measurements are made. The 'doorstopper' was designed primarily to measure the major principal stress in situations where its direction and those of the two other principal stresses were either known or could be assumed. For example, at great depth in undisturbed virgin ground, it is reasonable to assume that the maximum principal stress is vertical and that the other two lie in a horizontal plane. The borehole in which the 'doorstopper' is installed would thus be drilled in the horizontal plane parallel to one of the minor principal stresses, the direction of which would either have to be assumed or determined as described later. The stresses measured would be the vertical major principal stress and the principal stress acting in a horizontal plane normal to the borehole axis. It is possible, as will be shown later, to obtained the complete state of stress using 'doorstoppers'. In this event, it is necessary to make measurements in three boreholes drilled in any three known directions to each other and relative to a system of three orthogonal axes. The triaxial strain cell was designed to determine the complete state of stress in a single borehole drilled in any direction in any stress field. At first glance it would appear to supersede the 'doorstopper'. This is not necessarily true since there are

By V. A. Leão, V. S. Coimbra, V. A. A. Oliveira, R. F. M. de Souza, G. M. de Lima

A willemite concentrate consisting mainly of willemite (55.3%) and dolomite (15.6%) was reduced in a tube furnace with charcoal as reductant. The effects of temperature and varying reductant additions on zinc extraction were studied. A zinc recovery of 86% was achieved with 20% reductant in the charge at 1100°C. During reduction, the calcium oxide generated through calcination of the dolomite promoted decomposition of the willemite, thus lowering the temperature at which reduction took place. The presence of CaO improved the zinc recovery at all temperatures studied. The best zinc recovery (93%) was obtained in the presence of 5% CaO, 20% charcoal reductant, and at a temperature of 1100°C. The results show that the willemite concentrate studied has great potential to be used as a raw material for the Waelz process.

Nov 6, 2023

1. Books on management The following are available from Knowledge Resources, P.O. Box 3954, Randburg 2125. . Competitive advantage of nations, by Professor Michael Porter from Harvard Business School. This book highlights the importance of industries in contributing towards national competitiveness. It is being regarded as one of the 10 best business books published during 1990. . The borderless world, by Kenichi Ohmae, Managing Director of McKinsey in Japan. This deals with business in the new interlinked economy. . Megatrends 2000, by John Naisbitt and Patricia Aburdene. This book outlines the mega/macro trends that will

Jan 1, 1991

By P. King

In considering the available reserves of coal, the author points to the importance of improved recovery, and defines three extraction ratios: the geological extraction ratio (or exploitation factor), the economic extraction ratio (or mining factor), and the geometrical extraction ratio (or volumetric extraction factor). He discusses the factors affecting each of these ratios, and concludes that, although geological factors cannot be considered in isolation from technical and economic factors, the geological extraction factor is the most significant criterion of whether the best use is being made of coal resources.

Jan 1, 1980

By F. Reyes, M. Hilden, G. Forbes, M. Yahyaei

Since AlphaGo defeated the best human player in the game of Go in 2016 - something thought to be an impossible achievement - machine learning, deep learning and reinforcement learning have caught the attention of scientists, the media and the general public alike. This recent development in machine learning (let us remember that neural networks have been available for decades now) opens new possibilities in the areas of modelling and process control. However, little has been reported in the minerals processing industry about these new possibilities and opportunities. This paper presents and introduces the topic of reinforcement learning and the different platforms that allow its implementation. The paper shows the consequences of using reinforcement learning for the specific area of process control and optimisation. As an example, the authors present the use of reinforcement learning for the control of a SAG mill closed with a pebble crusher using industrial data from an operation. A comparison with advanced model-based process control is provided, showing the benefits and shortcomings of reinforcement learning as a new control and optimisation technique. Keywords: Reinforcement learning, deep learning, process control, process optimisation

Jan 1, 2020

By Stuart Marsland

"Reference materials have always been important for validating and controlling analytical methods', They have recently become even more important as quality requirements have become more stringent and customer demands for properly verified and controlled results increase. Clients, especially from the resource exploration industry demand critical validation of all results reported. Mintek has been producing geological and semi processed ore references since the early 1970's and recently due to increase in demand other manufactures have entered the South African Market.This paper describes Analytical challenges from the customer's perspective. The customer being the metallurgist, mine geologist, environmental scientist and geologists from resource companies. Reference Materials and their appropriate use and good understanding of them can aid greatly in building confidence in the results, choosing the right Laboratory for a project, deciding which set of results arc correct and providing evidence to the customer's clients that the results obtained are the very best possible.Throughout the world there are hundreds of reference materials produced by over 80 organisations and these are mainly ores, rocks, semi processed ores, metals, and many more. Mintek is one of the top 10 producers with over 75 products. Many of these producers including Mintek and their respective standards organisations belong to the ISO REMCO committee and their respective work groups. This committee's main task is to draw up guide lines for the use, manufacturing and certifying reference materials. In South Africa a mirror committee has recently had its inaugural meeting the function is to give clear mandate to the South African representative on the main ISO REMCO committee, the South African delegate bas an opportunity to influence the contents of the guides.Tile SARM program has since the year 2000 increased its sale three fold, the question is why? There is more accountability needed in our world. That means Analytical results have to be the very best possible and risks associated to them must be well quantified. Consider that the risk of wrong results of wrong decisions made from a result is trivial to laboratory, in comparison to the laboratories customers. The consequence to a laboratory could be a loss of income or some one may lose their job. To the customer he may dig up 1000 of ton's of rock with nothing in it or worse still don't mine it when the grade is high enough. This is seriol1s money."

Jan 1, 2014

By B. J. Coetzee, P. W. Sonnendecker

The quality control of a two-stage coal washing process involves several complex components that need to be modelled accurately, to enable autonomous control of the process. The first objective is to develop a method to track the material through the washing process, while ensuring accurate washing prediction models are used. This was achieved through a digital twin model of the Grootegeluk 1 coal processing plant. The model is the amalgamation of manipulating and combining of data-sets from the plant historian, geological wash tables, and mining dispatch servers. This information is then used to control and set the processing medium densities of all 15 modules on the plant, 10 modules in the primary wash and 5 modules in the secondary wash. This controller has been successfully implemented and controlled the plant for 10 days.

Aug 2, 2022

By Mr P. W. J. van Rensburg

SOUTH AFRICAN NATIONAL COMMITTEE ON TUNNELLING In 1970, the South African Institution of Civil Engineers, the South African Institute of Mining and Metallurgy, the South African Institute of Mechanical Engineers, and the Geological Society of South Africa held an international conference on tunnelling, known as Tuncon 1970. SUID-AFRIKAANSE NASIONALE TONNELBOUKOMITEE In 1970 het die Suid-Afrikaanse Instituut van Siviele Ingenieurs, die Suid-Afrikaanse Instituut vir Mynbou en Metallurgie, die Suid-Afrikaanse Instituut van Meganiese Ingenieurs en Die Geologiese Vereniging van Suid-Afrika 'n internasionale konferensie in verband met tonnelbou gehou, wat bekend gestaan het as Tonkon 1970.

Jan 5, 1974

AFRICAN NATIONAL COMMITTEE ON TUNNELLING In 1970, the South African Institution of Civil Engineers, the South African Institute of Mining and Metallurgy, the South African Institute of Mechanical Engineers, and the Geological Society of South Africa held an international conference on tunnelling, known as Tuncon 1970. SUID-AFRIKAANSE NASIONALE TONNELBOUKOMITEE In 1970 het die Suid-Afrikaanse Instituut van Siviele Ingenieurs, die Suid-Afrikaanse Instituut vir Mynbou en Metallurgie, die Suid-Afrikaanse Instituut van Meganiese Ingenieurs en Die Geologiese Vereniging van Suid-Afrika 'n internasionale konferensie in verband met tonnelbou gehou, wat bekend gestaan het as Tonkon 1970.

Jan 5, 1974

Written contribution by J.F. Curtist The paper is an interesting exercise in the application of mathematics to a theoretical situation presumed to oc¬cur underground. However, some of the assumptions on which the calculations are based are unlikely to occur in any actual mining situation. Assumptions made in the paper Objections to these assumptions are noted seriatim. (1) `it is assumed that any loading-rate effect will be small and can be ignored' (p. 3). A loading rate of the order of 50 kN-12 per cent of the maximum load-is customary to prevent the props being dislodged by the blast. (2) `it is unlikely that all the props will be installed with their full stroke available, but for the purpose of this analysis, it is assumed that this is the case' (p. 3). A more reasonable assumption would be that, with the most careful selection of prop length and the most rigid control of stope width, the available stroke length would on average be reduced by the order of 70 mm on installation-20 per cent of full stroke. (3) `each support unit supports a block of 3,3 m2 bound¬ed by vertical fractures with zero cohesion that are parallel and at right-angles to the stope face respec¬tively' (p. 5). Joughin and Jager have shown this to be an unwar¬ranted assumption in respect of the positioning, the direction, and the dip of the fractures present in a stope in rockburst conditions. If, as assumed, there was `zero cohesion' between such blocks, the removal of a hydraulic prop in row 3 supporting such a block would ensure that it fell out before a profile prop could be installed in the same position. (4) `the height of each of these blocks is 3,0 m, the volume of each block is 9,9M3, the mass of each block is 27 225 kg' (p. 5). The concept of individual props being affected by dis¬crete blocks of known and uniform dimensions of relatively low ground velocities (less than or equal to 2,16 m/s) acting in line with the axis of the prop is one that lends itself to neat mathematical calcula¬tions. It does not, however, bear much similarity to the actual conditions that are exposed underground in excavations where rockbursts occur. Ortlepp and co-workers concluded that `the impulse of the shockwave can cause the displacement of the

Jan 1, 1991

By Karl-H. Daum

Over many decades, numerous feasibility studies have demonstrated, that the production of sulphuric acid remains the most viable option of sulphur recovery from smelter off gas and abatement of SO2 emissions to the atmosphere. This is particularly more pronounced as smaller but more concentrated off-gas flows are to be treated from smelters, and enhanced sulphuric acid processes be-come available. Off-gas handling systems represent a significant capital and operating cost burden to the metallurgical operation. Modern pyrometallurgical smelter processes for sulphide ores based on the use of oxygen-enriched air, produce relatively small off-gas flows with high SO2 concentrations in the smelter gas of 30?60 %-vol. of SO2. This is a prerequisite for substantial cost reductions in the smelter off-gas handling and treatment system. As an alternative to sulphuric acid production, numerous scrubbing concepts with alkali or dual-alkali combinations as well as organic absorbents have been proposed. Also the reduction of the SO2 to elemental sulphur has frequently been studied. Very few of those alternative processes have been built in industrial scale, but all were generally characterized by none sustainable operation due to cost reasons, problems with issues related to chemicals used and by-products or poor availability. Thus the traditional concept of converting the SO2 to sulphuric acid is most common, although regarded as un-economic, but is at least a proven, environmentally sustainable and reliable way of sulphur gas processing. With the high acid price levels these days, operating companies are even able to generate significant revenue with their otherwise ?fatal? acid. Even though smelter gas is available at high SO2 concentrations, in a conventional acid plant one would add large amounts of air to dilute the gas down to a suitable concentration of 12?13 (14) %-vol. SO2. Dealing with higher SO2 concentrations in smelter acid plants is not feasible, as the gas exit temperature of the catalytic oxidation step would exceed the allowable limit for the catalyst. Hence those conventional acid plants are characterised by the use of large equipment, i.e. high capital cost, high energy consumption and limited flexibility. The newly developed LUREC® process can handle off-gas with significantly higher gas concentrations, even in excess of 25 %-vol. SO2. It is entirely based on well-proven equipment and unit operations. The first industrial application, operating with 16?18 %-vol. SO2 will be presented in this paper, along with the fundamentals of the process. It will be demonstrated that the process requires inherently lower capital cost, fewer operating cost, offers better energy recovery and lower emissions as compared to conventional design. While most existing smelter acid plants would have some built-in spare capacity, any significant increase of smelter capacity, say of 30%, can basically not be accommodated without installing an additional parallel new acid plant unit. An add-on LUREC® module can remove any such restriction, while simultaneously de-bottlenecking the existing acid plant. The paper also discusses the present status of the add-on technology for smelter acid plant expansions with respect to technical boundary conditions of different process alternatives as well as economic and environmental aspects. Application of the LUREC® process to modern smelter acid plants operating with high SO2 gas concentration, will lead to a substantial reduction of the specific size of the gas processing equipment and equivalent savings in capital and operating cost. The LUREC® process is patented worldwide by OUTOTEC.

Jan 1, 2009

By F. Dong, F. Yang, J. Wang, Z. Wang, D. Mingxia

Antimony oxide ores are important antimony resources, but their recovery is still a problem. In this paper, the adsorption behaviour and mechanism of dodecamine and quaternary ammonium salt on the surface of cervantite and quartz were investigated. The flotation behaviour of cervantite and quartz using quaternary ammonium salts and dodecylamine as collectors was studied by single mineral flotation experiments. The adsorbed amount was measured and infrared spectroscopy was used to study the ability of several cationic collectors to float cervantite and quartz. The results show that quaternary ammonium salts can simultaneously float the cervantite and quartz. It is difficult to achieve separation of the two minerals using quaternary ammonium salts as collectors. At pH>10, dodecylamine can float quartz but not cervantite, which can achieve reverse flotation separation of the two minerals. The difference between the abilities of quaternary ammonium salts and dodecylamine to float cervantite and quartz lies in the different ionisation properties of the two reagents. Quaternary ammonium salt is a strong electrolyte that is completely ionised in the pulp and exists mainly in the form of quaternary ammonium ions. Dodecylamine is a weak electrolyte and predominantly forms molecules under alkaline conditions. Keywords: Cervantite, quartz, dodecylamine, quaternary ammonium salts, flotation

Jan 1, 2020

By K. C. Sole, M. E. Mitshiabo

Although surfactants have proven to increase metal extraction by improving solution flow in porous media, these reagents have not been widely adopted in heap leaching operations because of potential incompatibilities with downstream processes that are subject to surface properties. The BASF leaching aid, LixTRA 118, was previously found to have no significant effect on post-leach operations. This study evaluated its performance in ores of different particle size distributions and the impact on acid consumption and metal recovery. Column leach studies, carried out on a copper oxide ore and mixed oxide–sulfide ore, showed that the effect of LixTRA 118 was more pronounced in ores with wider particle size distributions than in those with more uniformly sized particles. Solution percolation rates increased by up to 18% in the presence of leaching aid, and increased copper recovery and acid consumption. Improved wetting facilitated the kinetics of acid diffusion at macroand micropore level. There was no significant effect on iron recovery

Jan 1, 2023