Search Documents

By deur R. Dippenaar

'n Kort kursus oar die teorie en praktyk van hittebehandeling is vanaf 29 Junie 1981 tot 3 Julie 1981 in die departement Materiaalkunde en Metallurgiese Ingenieurswese aan die Universiteit van Pretoria aangebied. Die kursus is dour dosente van die departement opgestel en in samewerking met 'n aantal gassprekers aDder beskerming van die Suid-Afrikaanse Instituut vir Mynbou en Metallurgie aangebied. Tunnelling The Third International Symposium on Tunnelling is to be held in Brighton from 7th to 11th June, 1982. Professional development seminars The Department of Mining and Metallurgical Engineering of McGill University is to hold the following seminars during 1981-1982.

Jan 1, 1981

By I. James, R. J. Durrheim, M. S. D. Manzi, O. Valeshin, J. Lepine, L. V. Socco, C. Colombero, A. Malehmir, M. K. Rapetsoa, M. Sihoyiya

The FUTURE project aims to enhance seismic surveying in South African mining by integrating advanced acquisition technologies. In this paper, we detail surface and underground seismic surveys at the South Deep gold mine as part of the project. Surface seismic acquisition used co-located broadband micro-electromechanical sensors, one and three component recorders connected to geophones, distributed acoustic sensing using a straight fibre optic cable, along with a 6 ton broadband seismic vibrator operating with 4–180 Hz linear sweeps. In addition, underground surveys employed a combination of straight, and helically wound fibre optic cables, cabled-based and nodal sensors, along with a 500 kg drophammer mounted on a skid steer bobcat. The surface and underground seismic arrays were time synchronised using a GPS-time transmitter to allow for accurate seismic data recording in a GPS-denied environment. Results show the efficacy of these techniques in acquiring high-resolution seismic data, revealing detailed subsurface geological structures and mineralisation down to 3500 m below ground surface. Surface data revealed clear seismic reflections corresponding to the Black Reef and Ventersdorp Contact Reef. An underground P-wave velocity model exhibits low velocity anomalies that are associated with fracturing, while a P-wave reflection stack section shows significant reflections and a degree of faulting below the tunnel floor that was not observed on the surface reflection seismic data. We highlight the potential of these technologies to enhance safety, efficiency, and sustainability in mining. This study sets a benchmark for future reflection seismic surveys, paving the way for safer, more efficient, deep mineral exploration and extraction practices.

Jan 12, 2025

By T. Dlokweni, M. Bester, C. Koegelenberg, I. Basson

Certain degrees of safety, economic, and financial risk are implicit in any mining operation. At Thabazimbi Mine, slope stability was one of the major sources of risk, largely due to data uncertainties. Consequently, a risk-based approach in slope design was followed. On 6 June 2015, a slope failure occurred in Thabazimbi Mine’s Kumba pit, involving approximately 65 million tonnes of rock failing into the pit and the valley below. Although the failed mass moved rapidly and resulted in a run-out distance of approximately 900 m, controls had been put in place to successfully evacuate all personnel. Risk assessment during the onset of failure supported the decision to not compromise the safety of personnel in any way, leading to unavoidable equipment loss. This contribution presents the failure as a case study in the context of a risk-based approach to slope design as well as the importance of implementing geotechnical controls to effectively manage slope instability risk. Furthermore, a comprehensive back-analysis was performed, on a fully constrained 3D model, utilising 3DEC software, to gain insights into the failure mechanism. In conclusion, lessons from the Thabazimbi slope failure are valuable as they demonstrate the importance of following a risk-based approach in slope design to effectively manage safety and financial risk in open pit mines.

Sep 1, 2025

1. Book reviews Geostatistics for natural resources characterization, edited by G. Verly, M. David, A.G. Journel, and A. Marechal. Hingham (MA 02043, U.S.A.), D. Reidel Publishing Co., 1984. Pt I: 606 pp. Pt 11: 518 pp. U.S.$135,50 per set. Reviewer: D.G. Krige Magnesium, the international perspective, by Peter King. London, Financial Times Business Information Ltd, 1984. £120. 147 pp. Reviewer: D.G. Maxwell 2. Mintek reports Report M156 A kinetic study of the reactions of certain gaseous sulphur compounds with iron. Report MI57 Reaction mechanisms in the reduction of Winterveld chrome spinel with graphite and carbon. Report MI72 Computer programmes for the control and datamanipulation of a sequential X-rayfluorescence spectrometer. Report MI77 A proposed test for the determination of the grindabi/ity of fine materials. Report MI86 A survey of the erosion, corrosion, and abrasion of material-handling systems in the mining and mineralprocessing industry. 3. New journal Advanced materials & processes, issued monthly by American Society for Metals (Metals Park, Ohio 44073, U.S.A.). CIM conference The combined 24th Annual Conference of Metallurgists and the 15th Annual Hydrometallurgical Meeting will be held in Vancouver from 18th to 22nd August, 1985. Light metals The 8th International Light Metals Congress will take place from the 22nd to 26th June, 1987. These meetings, which take place traditionally every few years, are organized by the Austrian Metals Industry Association, the Austrian aluminium industry, and the University for Mining and Metallurgy in Leoben, in collaboration with the Aluminium-Zentrale Diisseldorf. President of AS&TS* Mr Arthur Woodington Reynolds (Sam) took office as President of The Associated Scientific and Technical Societies of South Africa on 28th November, 1984. Sam Reynolds was born in Boksburg on 27th December, 1930, and received his education at Christian Brothers College in Boksburg and at St John's College in Johannesburg. World mining Sweden, Finland, and Norway expect representatives of all mining countries in May-June 1987 to the 13th World Mining Congress in Stockholm. The Swedish Mining Association, the Finnish Association of Mining and Metallurgical Engineers, and The Association of Norwegian Mines will organize the Congress, together with the International Organizing Committee of the World Mining Congress. Sheet metal The German Group of the International Deep Drawing Research Group (IDDRG) will be organizing the 14th Biennial Congress of the IDDRG on 21st to 26th April, 1986, in Cologne and Munich. Safety in mines The 21st International Conference of Safety in Mines Research Institutes is to be held in Sydney from 20th to 25th October, 1985. ILAF A conferences The Instituto Latinoamericano del Fierro y el Acero (ILAFA) has scheduled the following congresses for 1985. Mechanical testing of materials The Deutsche Gesellschaft fiir Metallkunde, together with the Deutschen Verband fiir Materialpriifung and the Fachhochschule Osnabriick, is holding a course on the methods used for the mechanical testing of materials at Osnabriick from 9th to 11th September, 1985. Mine ventilation The Second U.S. Mine Ventilation Symposium will be presented from 23rd to 25th September, 1985, in Reno, Nevada, by the University of Nevada-Reno's Mackay School of Mines and Division of Continuing Education.

Jan 1, 1985

By D. F. Malan, R. P. Els

The limit equilibrium model, used in displacement discontinuity codes, is a popular method to simulate pillar failure. This paper investigates the use of physical modelling to calibrate this model. For the experiments, an artificial pillar material was prepared and cubes were poured using the standard 100 mm × 100 mm civil engineering concrete moulds. The friction angle between the cubes and the platens of the testing machine was varied by using soap and sandpaper. Different modes of failure were observed depending on the friction angle. Of interest is that significant loadshedding was recorded for some specimens which visually remained mostly intact. This highlights the difficulty of classifying pillars as failed or intact in underground stopes where spalling is observed. The laboratory models enabled a more precise calibration of the limit equilibrium model compared to previous attempts. Guidelines to assist with calibration of the model are given in the paper. The limit equilibrium model appears to be a useful approximation of the pillar failure as it could simulate the stress-strain behaviour of the laboratory models.

May 3, 2023

By P. Valicek

Anglo American Platinum Limited is constantly striving to improve safety and productivity. There are many different initiatives taking place within the organization in order to ensure continued safe operation and profitable ounces for the future. One of the opportunities and potential growth areas that has been identified and is being explored is that of mechanization. In order to do this, the approach that has been adopted by Anglo American Platinum is to fully understand and analyse the current mechanized mining methods. Once each configuration is fully understood, the method can then be optimized and new mining technologies and systems can be developed to overcome the current shortfalls. This paper will discuss a methodology that was developed by Anglo American Platinum (in conjunction with Cyest Corporation) and adopted to optimize the mechanized mining layout and fleet configuration, and will also present the final findings of the study. Due to the impracticability of piloting every possible option in the workplace, extensive modelling and simulation exercises were conducted to determine realistic parameters for productivity and value. The study resulted in a full understanding of mechanized mining systems and their associated layout. From the results of the study a mining / logistic layout was developed which highlighted the following opportunities: 1. Create safe operations through the reduction of personnel in the ?high-risk zone? of stopes 2. Separate machines and personnel by use of remotely operated machines 3. Create focused mining on primary development from the production stoping, thus having dedicated teams on development and stoping. 4. Develop primary development ahead of the stoping activity. This enables: a) Understanding of the geology and subsequent implementation of the correct b) technology (?fit-for-purpose?) required to mine that area based upon this geological knowledge c) Ability to install tipping points ahead of stoping, creating ?immediate stoping reserves?, thus increasing flexibility and reducing production risk d) Improved productivity by having adequate faces available and reduction in re-development to establish faces. 5. Quicker return on Investment due to recovering revenue from ?on-reef development? 6. The layout allows flexibility between stope sections enabling better ?resource sharing? 7. Optimize the long-term ratio of machine makeup of the fleet in relation to the production outputs 8. Creates an agile mining layout allowing rapid response to market pressures. The findings and work presented in this paper is currently being implemented at different test sites within Anglo American Platinum and will demonstrate that improved safety and productivity can be achieved through the adoption of mechanization.

Jan 1, 2012

By E. P. Preis, R. C. W. Webber-Youngman

The real cost of any mining incident has, empirically, proven to be estimation-driven, rather than factdriven. One of the main reasons for this lies with the complexity of the cost composition of any given mining incident. Incident costs comprise both direct and indirect cost factors, and in many cases the costs associated with these factors are incurred during different time periods following the incident. In this paper we aim to identify the various cost factors arising from mining incidents, provide a thorough understanding of all the potential cost factors identified, and draw general conclusions on the knowledge obtained. Furthermore, recommendations are made on how mining companies could use the results, in order to assist them in calculating the costs of mining incidents. The paper also provides suggestions for further research, with the emphasis on the most significant immeasurable cost factors, namely the costs of implementing job accommodations following an incident, the harm to company reputation, and the decreased productivity due to low worker morale/psychological factors following an incident. If mining companies are aware of and understand which factors could contribute to the cost of any given incident, future planning and incident cost estimations could be easier. It should, however, be noted that although this study provides a comprehensive list of cost factors (and detailed explanations), other unknown cost factors relating to mine incidents could prevail in extreme cases.

Jan 1, 2021

By L. Ntlhakana, K. Khoza-Shangase, G. Nelson, I. Maposa

Occupational noise-induced hearing loss (ONIHL) is associated with various risk factors in South African mines. We investigated the association between standard threshold shifts (STSs) and exposure to noise and platinum mine dust (PMD), using demographic data, five years of annual audiometry screening results, and noise and dust exposure data. Miners’ age, sex, percentage hearing loss (PLH), and dust and noise exposure data were gathered, and a linear mixed effects regression model used to predict STS. Average occupational exposure levels to noise and dust were calculated from recorded measurements. A total of 12 692 records were analysed. Most miners were male (89.6%) and more than 50% were younger than 41 years. More than 70% were exposed to > 85 dBA noise and 58% were exposed to 1.5–2.99 mg/m3 PMD. Changes in hearing levels ranged from 8.3 dBHL at baseline (2014/2015) to 10 dBHL in 2016 (STS), with no changes thereafter. The model showed that the estimated effect on STS for males was 27% and 21% higher than for females, for the left and right ear, respectively The estimated effect of age, PLH, noise exposure and years of exposure on STS was < 10% for each variable. There was no statistically significant association between PMD and STS. The combined effects of age, sex, years of exposure to noise, and noise exposure levels, and strength of associations can be used to predict STS for this group of miners. Our findings may be used to measure the efficacy of the mine’s hearing conservation programme.

Aug 1, 2021

By A. Ennen, R. Wagner, B. Orberger, J. -M. Milazzo, N. Uhlmann, J. Banchet, J. Lucic, N. Wörlein, M. Firsching, J. L. Dubos, C. Bauer

The residues from mining and processing ores can often be considered as secondary raw materials. However, the material is only available in the form of fine particles (< 3 mm). In order to recycle these wastes, it is necessary to agglomerate it for transportation prior to reprocessing. The resulting agglomerates need to mechanically resist the stress of transportation and loading into the furnace. X-ray computed tomography (CT) is an established method for characterisation of internal structures in material science. This non-destructive technique can provide information on size and distribution of particles and grains. However, the information is not limited to the size, but also can yield structural features like orientation and position of cracks and fractures, which are important features indicating potential for deteriorating the agglomerates. Furthermore, deduced features such as contact conditions of inclusions or boundary surfaces can also be calculated. We studied binder-free tablets of manganese-oxyhydroxide, bentonite, kaolinite and slag powder using micro-CT. Inclusions of highly absorbing particles were identified using a watershed transformation with automatic segmentation by Otsu thresholding. Subsequently, the resulting data was analysed regarding their volume percentage, distribution in size and location within the sample. For the slag agglomerates, the volume fraction of iron could be determined. Furthermore, visible cracks were investigated with the goal to determine the long-term durability. It was shown that the data provided by micro-CT is reliable and helpful for the characterisation of industrial waste agglomerates. Keywords: X-ray, computed tomography, micro-CT, agglomerates, manganese fines, slags, kaolinite, bentonite

Jan 1, 2020

By T. Chikande

"Falls of ground pose costly hazards to personnel and equipment and thus measures should be taken to prevent them. This study endeavours to improve the support systems used in geotechnically poor ground at a Zimbabwean platinum mine by analysing the status quo and recommending an effective support system. Various techniques were used to determine the quality of ground conditions, predict the rock mass behaviour, and to identify the appropriate rockbolt type. An analysis of the current ground control methods and their limitations was also undertaken.The results showed that the current support system and mining practices in poor ground need to be modified to improve safety and productivity. Stoping overbreak is influenced by poor ground conditions and the explosives currently used. The use of emulsion is recommended to replace ANFO. Redesigning of pillars is also recommended in poor ground conditions. An evaluation of the current roofbolt system indicated an opportunity for improvement. With new insight on the performance of the shorter length roofbolts currently in use, a new support system was recommended taking into consideration cost-benefit analysis. Barring down using pinch bars in poor ground was seen as a risky and time-consuming exercise, hence the use of mechanical scalers is recommended to achieve zero harm and to meet production targets. Smoothwall blasting is recommended in poor ground to minimize excavation damage. Other recommendations include the use of hydrological surveys to determine groundwater levels and implement corrective measures. Both empirical and numerical modelling approaches need to be utilized in determining the optimum support. IntroductionThe presence of geological discontinuities such as faults and joints weakens the rock mass. Adequate support is critical in achieving zero harm in underground mines. This paper reviews the current support systems used in poor ground conditions at a Zimbabwean platinum mine. The area of research is located on the Great Dyke of Zimbabwe. The mine exploits platinum group elements (PGEs) and base metals. It is shallow, having a maximum depth of less than 300 m. The Great Dyke is the second largest reserve of PGEs, following the South African Bushveld Complex (Oberthur et al., 2012). It is a linear layered intrusion that extends for about 550 km with a maximum width of 11 km (Prendergast, 1989). The generalized section of the Great Dyke is almost like a trumpet, comprising layers that dip towards the centre. The reef exploited at the mine, the Mineralised Sulphide Zone (MSZ), is located in the pyroxenite layer, which is hosted in the ultramafic sequence. The MSZ is a uniform layer about 2– 3.5 m thick, dipping at around 10–14° from surface outcrop towards the axis of the basin, and located between bronzite and websterite horizons. The visible disseminated sulphide mineralization shows a typical and consistent vertical distribution of platinum group metal (PGM) and base metal values. The research was undertaken to review the current support systems used in geotechnically poor ground conditions in a bid to improve both safety and productivity."

Jan 1, 2016

By J. D. Steenkamp

In 2002 the commissioning of an ilmenite smelter on the North Coast of South Africa was extended by three months due to the failure and subsequent replacement of the magnesia-based refractory lining. The lining failed due to the hydration of magnesia caused by an unexpected source of water. The incident resulted in significant financial losses and a prolonged insurance claim which was settled in 2009. As magnesia-based refractories are used extensively in both ferrous and non-ferrous applications, the authors of the paper want to share the experience gained from this incident with others. The paper reviews the literature available on furnace start-up practices and explains the hydration of magnesia using available sources. The incident is studied in more detail, both technically and economically, and the costs incurred are quantified in terms of the cost of the original lining. The paper concludes with lessons learned and recommendations made for future work. The intention of the paper is to stimulate open debate regarding best practices in preheating of furnaces lined primarily with magnesia. Keywords Commissioning, hydration, start-up, magnesia.

Jan 1, 2011

By P. Vlasak, Z. Chara

Since the flow behaviour of slurry containing both coarse and very fine particles has not been sufficiently clarified, the paper focuses on the experimental study of the particle size distribution, time and intensity of shearing and the effect of chemical agents on the hydraulic gradient versus the average velocity relationship of fluidic ash slurries in the laminar and turbulent regimes. The recirculation pipe loop with smooth stainless steel pipes of inner diameters 26.8 and 36 mm was used for measuring the ash-water mixtures flow parameters. The dense fluidic ash-water mixtures behave as time dependent non-Newtonian slurries. Shearing, the addition of bottom ash or chemical agents, favourably affects the flow behaviour of dense fluidic ash-water slurries. The hydraulic gradient in the laminar region significantly decreases; also the laminar/turbulent transition region is reached for lower flow velocity.

Jan 1, 2007

By A. M. Garbers-Craig, T. Coetsee, T. M. Nemavhola

Accretions often form in furnaces when slag and charge materials attach to the refractory wall and build up over time. Accretion formation is usually unwanted because it reduces the working volume of the reactor and hinders material flow through the reactor. However, in some instances a thin, stable accretion layer may be desirable to protect the underlying refractory material. In order to prevent and/or manage accretion formation, it is important to understand the underlying principles of this phenomenon in the particular reactor. Excessive accretion formation hampered production at the Exxaro FerroAlloys ferrosilicon melting and atomization plant. This plant uses induction furnaces in which a 15% silicon-iron alloy is produced by batch smelting a mixture of ferrosilicon of 75%Si grade and low-carbon steel. The molten ferrosilicon alloy is then gas-atomized to a powdered product for use as a dense medium in mineral processing plants. The objective of this study was to investigate the effect of different impurity levels in the ferrosilicon feed material on the extent of accretion formation as well as the effect on the accretion properties, which influence the ease of accretion removal upon furnace shut-down. Refractory and accretion samples were collected after a furnace shut-down and characterized using X-ray diffraction and scanning electron microscopy–energy dispersive spectroscopy. It was concluded that the trace elements in the FeSi-75 feed material (Al, Ca, Mn) were mostly responsible for accretion formation, but that rust on the low-carbon steel and oxidation of the steel contributed to accretion attachment to the lining. The total contaminant content, calcium to aluminium ratio in the FeSi-75 feed material, and thereby the liquid to solids ratio in the accretion at temperature determine the strength of attachment as well as growth of the accretion.

Feb 2, 2021

By K. Barani, F. Moradpouri, M. Godarzi

A sampling campaign carried out on the lead flotation circuit at Lakan lead-zinc processing plant demonstrated that the Pb recovery was only about 68-69%. Characterization of the Pb flotation tailing showed that 61.4% of the Pb is in the –37 μm size fraction, which is difficult to recover by flotation. Batch flotation experiments were carried out on a plant sample of the lead flotation feed and high-intensity conditioning (HIC) was used to improve flotation recovery. The results showed that increasing the collector conditioning time from 1 to 3 minutes significantly increases the Pb recovery from 42.5% to 57.3%. Further increases in conditioning time to 5 to 7 minutes decreased the Pb recovery. With a collector conditioning time of more than 3 minutes, due to the surface cleaning effect, increasing collector and frother dosage improved the flotation selectivity and recovery, even at higher collector dosages. The Pb recovery increased from 69.1% to 79.8% with increasing impeller speed from 600 to 1250 r/min. HIC increases the flotation kinetics and greatly improves the flotation recovery and concentrate grade.

Apr 2, 2022

By G. Coetzer

"Prior to operating a non-recovery coke pilot plant, it was critical to ascertain coal cake stability during the loading of a 1 m3 coal cake into the oven. Various compaction parameters were verified and established on a small laboratory-scale compaction machine to obtain a coal cake of acceptable stability. These parameters include cake density, cake surface moisture, transverse strength (force applied perpendicular to the original compacted coal cake layers), and applied force to the coal cake. This work determined the behavioural characteristics of the coal while being compacted either with a full-sized or a 1/3-sized compaction plate in a 9 kg capacity mould. Two different coals were evaluated, namely Waterberg semi-soft coking coal (sscc) and Oaky North hard coking coal.The target wet cake density of 1 100 kg/m3 (79% of 1 400 kg/m3 relative density) was achieved for Waterberg sscc, with a particle size d50 varying between 0.6 mm and 1 mm, utilizing the 1/3-sized compaction plate in the laboratory-scale set-up, with 11.6% surface moisture and 92.2 t/m2 commercial equivalent applied force. For Oaky North hard coking coal, a wet cake density of 1 189 kg/m3 (85% of 1 400 kg/m3 relative density) was achieved at a surface moisture content of 12.3% and at a lower applied force than that for Waterberg sscc, i.e. 78.5 t/m2.Coal cakes of acceptable strength, and therefore sufficient stability for further processing, were obtained for all materials evaluated during this study.Further studies should be conducted to determine the effect of zeta potential during the compaction of coals.IntroductionExxaro Resources has successfully installed and commissioned a world-class stamp-charging horizontal 1 t electrically-heated pilot-scale coke oven at its Metallurgy Services facility. Prior to operating the coke non-recovery pilot plant, it is essential to ascertain coal cake stability during the loading of a 1 m3 coal cake into the oven. The design of Exxaro’s pilot plant is such that the coal cake is pushed inside the oven by means of a pusher plate, rather than through a ‘spoon’ feed mechanism, such as is found in industrial horizontal coke ovens. The pusher plate loading mechanism dictates that the coal cake should possess high stability and inherent strength during loading into the oven, owing to frictional forces exerted by the oven floor. In order to obtain a coal cake of acceptable stability, various compaction parameters needed to be verified and established on a small laboratory-scale compaction machine."

Apr 1, 2019

By C. Hsu

Underground coal gasification (UCG) is becoming more popular as the reserves of good quality, mineable coal are starting to diminish, and yet the global energy demand from coal is still increasing. The purpose of this research project was to investigate cavity formation within a coal block due to the combustion reactions in the context of UCG. The cavity plays a pivotal role in the UCG process, as it is essentially the gasification reactor. Cavity formation in an in situ gasification process using the forward combustion linking method (FCL) had been investigated, and a laboratory model was created to simulate the process. The experiment was performed by drilling a U-shaped tunnel into a coal block, which was then combusted internally with air that was fed through an injection hole. A heating element (at approximately 500°C) was used to supply the required heat for combustion at the base of the injection well. The coal blocks were analysed using micro-focus X-ray tomography. The tomography results showed that the coal tended to crack along the bedding plane after a short duration of combustion, due to either the formation of clinker or the expansion of swelling vitrinite along the horizontal tunnel. The deposit was thicker at the base of the injection well compared to the base of the production well; this may have been caused by the turbulence of the air flow and the relatively high oxygen concentration at the base of the injection well. A comparison of the results with work by Daggupati et al. (2010) showed the same trend, despite the slightly different methodology applied.

Jan 1, 2014

By M. I. Mabala, B. P. Watson, M. J. Kanda

A failed and stable Upper Group 2 chromitite pillar database was collected in 2007 as part of the PlatMine 1.2 pillar strength project. The database consisted of 177 pillars, of which 33 had failed. Most of the data were collected from various intermediate-depth mines near the town of Thabazimbi. Spans between rows of chain pillars were about 30 m. Pillar loads were estimated using pseudo-3D, elastic, boundary element modelling software. The pillar-load data were evaluated using a maximum likelihood regression analysis to determine strength parameters, following a similar approach to historically acceptable practice. The original formula was named the PlatMine Formula. This paper describes re-evaluations of the database, using a linear formula and several variations of the power formula. The formula providing the lowest standard deviation to the data in the database was considered the best representation of the pillars in the database. Through this rigorous process, a new formula for peak pillar strength was developed for Upper Group 2 chromitite pillars, which is unaffected by volume. The small standard deviation provided by this formula suggests a reliable relationship between strength and w/h ratio, in the w/h ratio range between 1.5 and 4.7. Accuracy, precision, and recall analysis confirmed the efficacy of this equation to the data in the database. Importantly, the new formula provided in the paper does not predict a significantly different strength to the current PlatMine formula, within the confines of the database.

Nov 27, 2024

By J. S. Contreras, E. Córdova, I. Gottreux, A. Anani, A. Ferrada

Cave mining is an underground mass mining technique. The largest projects, which are known as ‘super caves’, produce hundreds of thousands of tons of ore per day, which involves large footprints with considerable column height, and have a life of mine of over 20-40 years. These operations are typically located deep, under high stresses and in competent rock masses, making initiation and propagation of the caving process harder to manage. These challenges must be confronted by optimizing the fragmentation of the orebody to achieve smaller size blocks that will result in consistent caving and improved flow of the ore from the drawpoints. To achieve better performance from the drawpoints, preconditioning is applied to fragment and damage the material required to cave. We present a proposed design for preconditioning in underground mines, considering the challenges that these large-scale mines are already facing, based on a comprehensive analysis of current design parameters, case studies, and sensitivity analyses using numerical models.

Feb 2, 2021

By V. G. Pienaar, B. M. Mbiya, P. T. Slatter

[a constant b constant cc onstant c&apos; constant D pipe diameter (m) Dshear shear diameter (m) E error function fth theoretical friction factor F function F&apos; function K fluid consistency index (Pa sn) kv valve loss coefficient L pipe length (m) n flow behaviour index N number of data points ?P valve pressure drop (Pa) Q flow rate (m3/s) Re Reynolds number Re3 Reynolds number (Slatter) V average velocity (m/s) Vann annulus velocity (m/s) x variable X number of independent variables y variable Y number of fundamental dimensions z variable µeff effective viscosity (Pa s) ? valve degree of opening d partial derivative ? fluid density (kg/m3) [ ] function]

Jan 1, 2007

By D. Botha, J. F. Cronjé

"SynopsisAlthough women all over the world have been involved in mining activities for centuries, mining has always been considered a very masculine industry due to its heavily male-dominated workforce as well as the physicality of mining work. The mining industry has not been an obvious career choice and preferred place of employment for women; women were mainly employed in administrative and advisory positions. Until 1994, women were legislatively prohibited from being employed in underground operations in South Africa, but the Mines Health and Safety Act, No. 29 of 1996, removed these restrictions. In addition, new mining legislation (the Mineral and Petroleum Resources Development Act, No. 28 of 2002) and the accompanying Mining Charter make specific provisions for the inclusion of women in core mining activities and require 10% of core positions to be filled by women.This article voices perceptions of the physical ability of women employed in core mining positions. Findings are drawn from empirical work undertaken at platinum, phosphate, and copper mines. Quantitative and qualitative research paradigms are used. It is evident that women find it extremely difficult to perform mine work that requires physical strength and stamina. Practical recommendations, informed by the literature review and empirical findings, are made with the objective of contributing to the sustainable deployment of women in the mining industry.IntroductionFor many years, mining has been considered the foundation of the South African economy. Although the mining industry in South Africa is currently under considerable pressure and experiences various challenges, including escalating operational costs, electricity tariff increases, safety-related issues and associated production stoppages, poor productivity, labour unrest, and reduced demand both globally and domestically, it remains a key contributor to the national economy and development of the country (IDC, 2013, p. 9).Until 1994, women were legislatively prohibited from meaningful participation in the mining industry and were denied access to skills and jobs, self-employment, and entrepreneurship. The newly elected democratic government in 1994 initiated substantial socio-political and economic transformation in South Africa. Nearly every sector in the country was transformed and re-shaped, primarily through sector-specific legislation, but also through negotiations between government, industry, and labour unions to create and refine the so-called sector charters, which included the Mining Charter. The vision of the new regime, the African National Congress (ANC), was to ‘transfer power to the people and transform society into a non-racial, non-sexist, united, democratic one, and change the manner in which wealth is shared, in order to benefit all the people’ (ANC, 2007)."

Jan 1, 2015