Search Documents

By M. Saghaeian, R. Hejazi, L. Hosseini, M. V. Sheikhzadeh

HPGR equipment has been well proven to be energy-efficient in the first stage of grinding in iron ore beneficiation plants. Numerous advantages of utilising HPGR grinding prior to ball mill grinding, such as reducing the power consumption in a ball mill through generation of micro-cracks, has been thoroughly studied. Less attention has been paid to efficiency of the HPGR circuit rather than the downstream ball mill circuit. In this study the HPGR circuit has been optimised through feed size reduction by crushing, and feed iron content upgrading by dry cobbing. This optimisation leads to better operation of the HPGR, and a smaller product size which is expected to result in a lower wear rate of ball mill liners and balls. It is also expected that the top size of the ball mill balls be reduced. Additionally, by reducing the feed size of HPGR from 30 mm to 15 mm, it is possible to achieve similar K80 of HPGR product in lowered pressure, i.e. 2.5 N.mm-2 instead of 3.5 N.mm-2 which translates to ease of operation. Similarly in a given roll pressure, smaller feed sizes result in higher specific throughput of ~10% which means higher production capacities. The results also reveal that this optimisation increases the concentrate weight recovery by about 10%. It also results in slight increases in the Fe grade of the product iron concentrate. Keywords: HPGR, HPGR circuit optimisation, crushing prior to HPGR, dry cobbing prior to HPGR, ease of operation, concentrate grade optimisation, weight recovery optimisation

Jan 1, 2020

By van der Merwem J. N.

"Coal pillars are prone to scaling over time, and are progressively reduced in size and consequently subjected to increased load and reduced strength. The effective factor of safety therefore reduces. Databases of failed and stable pillars cannot, therefore, be regarded as definitive.More than a decade has passed since the first attempt to predict the lifespan of pillars. This paper presents a review based on the new database and pillar strength equations. The methodology for the analysis is based on the fact that pillars scale. The ultimate safety factor (defined as the ratio between strength and load at the time of failure) is derived, followed by an estimate of the rate of pillar scaling, which results in an estimate of the expected time of failure.It is suggested that the predicted lifespan should not be used as an absolute indicator of expected pillar life, but rather as an index – the pillar life index (PLI) – to complement the safety factor and related probability of failure when evaluating pillar stability. A pillar with a predicted lifespan of less than 500 years would be regarded as being in danger of imminent collapse, while a lifespan of at least 1 000 years should be required for long-term purposes.The differences between this analysis and that published in 2003 constitute a strong case for regular reviews of all the empirically based stability indicators, namely the safety factor, probability of failure, and the PLI. Reviews at 10 year intervals appear to be required.The constants in the proposed method are valid only for the Witbank No. 1, 2 and 4 seams and the Highveld No. 2 and 4 seams.IntroductionIt is well known that over time, coal pillars are prone to scaling, and thus are progressively reduced in size and consequently subjected to increased load and reduced strength. The effective factor of safety therefore reduces and it is quite possible for failure to occur after a long time interval. In fact, scrutiny of the database of failed pillars indicates that failure occurred after periods ranging from 2 to 49 years, and not immediately after mining.The factor of safety for pillars at the time of failure is not the same as that immediately after mining. The concept of the safety factor is based on the pillar strength obtained by statistical analysis of pillar dimensions immediately, or within a month after mining, when the surveys are conducted. Strictly speaking, the safety factor as commonly used is valid only immediately after mining, and it continues to reduce thereafter. The ideal situation would be to base analyses of pillar strength on pillar dimensions at the time of failure, but that is simply not possible because the real dimensions cannot be measured at that time."

Jan 1, 2016

By G. J. McDougall, M. J. Nicol, O. L. Wellington, R. G. Copperthwaites, R. D. Hancock

X-ray photoelectron spectroscopy showed that the adsorption of gold cyanide on carbon in the presence or absence of electrolytes and acids proceeds by the same mechanism. Although the identity of the gold cyanide adsorbate is not known, the mechanism appears to have an initial adsorption stage that involves the adsorption of an ion pair: Mn+[Au(CN)-2]n where Mn+ is a metal ion (for example Na+, K+ and Ca2+) that has a lower solubility than the Au(CN)-2 anion in the adsorption medium, followed by a reduction step in which either a sub-stoichiometric Au(CN)x surface species or a cluster-type compound of gold is formed.

Jan 1, 1980

By M. Andersson, R. Elsrud

The quality and the production rate for the mining operations in the Garpenberg mine has been much improved due to a new system, that presents the latest exploratory and planning data for the driller at the moment he deploys the drill rig at the face. Other components in this improvement work are better planning procedure, large-scale production system with longer rounds and introduction of new drill rigs in the mine. The new Rig Control System (RCS) for the new series Atlas Copco Boomers L2C has made it possible to develop this system for production drilling in the Garpenberg mine. The ABC Regular has been extended with map navigation and drill plan generator. The driller will have the best estimate of the orebody in front of him and the best drill plan for that orebody. The customer’s specific system will also become a standard Atlas Copco product for the Boomer ABC drill rig family.

Sep 1, 2001

By K. Woodward, Y. Potvin, B. McFadyen, M. Grenon

Open stoping has become a popular mining method in hard rock mines, not only due to the safety of the method as a non-entry approach, but also because of the high extraction rate and low costs. At mine sites, stope performance is evaluated by calculating stope overbreak using the stability chart. However, limitations of the stability chart regarding the precision of the predictions, nonconsideration of factors such as the influence of blasting, and the exclusion of underbreak have led to non-optimal designs. The capabilities of today's computers have increased the amount of data being collected and the power of models being built. This article presents a step towards a new stope design approach where stope overbreak and underbreak are measured and georeferenced using octrees at an approximately cubic metre resolution and predicted using multivariate statistical models (partial least square, linear discriminant analysis, and random forest). Results show that overbreak and underbreak location along the design surface and their magnitude are predicted with good precision using a random forest model. These predictions are used to build the expected geometry of the open stope. The resolution of the data and the use of multivariate analysis has enabled the prediction of variation in stope performance along the design surface, going well beyond the simple qualitative per stope face prediction provided by a traditional stability chart approach.

Jun 5, 2023

By N. Naude, L. S. Leal Filho, M. P. Tshazi

In this paper, the authors performed experiments in the Denver and Leeds laboratory flotation devices at the University of Pretoria at various particle sizes to evaluate the performance of the devices. Quartz was used in a single mineral system at discrete sizes fractions, -25 μm, +25- 45 μm, +45-75 μm, and +75-106 μm. Hydrodynamic analysis, based on dimensionless power and Reynolds numbers, indicated that the Leeds cell required higher power input to achieve comparable flow conditions. Specifically, the Leeds cell exhibited an average power number of 1.03, whereas the Denver cell averaged 0.77 within the same impeller speed range of 1000 rpm–1500 rpm. For comparative flotation performance, impeller speeds were calibrated, resulting in operating speeds of 1200 rpm for the Denver cell and 1400 rpm for the Leeds cell. The cells performed similarly at two coarser-sized fractions. However, some deviations were observed in the finer particle size range. The -25 μm (fine) fraction initially achieved a recovery of only 15%. An additional reagent dosage was required to enhance the recovery of this fraction significantly. These findings highlighted the influence of particle size on flotation recovery. For all experiments, the Denver laboratory flotation cell outperformed (defined by higher recovery) the Leeds device, while still operating at a lower impeller speed. This advantage can be attributed to its impeller-stator design and air dispersion features, effectively overcoming slurry resistance and resulting in superior flotation performance compared to the Leeds cell.

May 27, 2025

Your Council has pleasure in submitting its report for the year ended 30th June, 1969. COUNCIL The following served as Office Bearers during the year under review: Messrs. R. C. J. Goode (President), J. K. E. Douglas and V. C. Robinson (Vice-Presidents), P. Lambooy (Immediate Past President) and D. G. Maxwell (Honorary Treasurer). Members of Council: Messrs R. J. Adamson, M. Barcza, F. P. Bath, Or J. M. Bereza, Or W. Bleloch, Messrs H. Britten, H. E. Cross, A. R. C. Fowler, A. E. Gilfillan, G. W. Holl, Prof D. D. Howat, Or J. P. Hugo, Messrs C. J. Irving, D. M. Jamieson, J. G. Kirchner, Prof J. de V. Lambrechts, Mr C. E. Mavrocordatos, Or J. T. McIntyre, Mr J. A. Nixon, Prof R. P. Plewman, Messrs J. F. Reid, H. Simon, C. G. Sowry, W. T. Stobart and P. W. J. van Rensburg. Ten Council meetings were held during the year with an average attendance of eighteen. FINANCE The annual accounts, which are attached to this report, show an excess of expenditure over income of R2,124, compared with an excess of income over expenditure of R4,218 last year. There are a number of reasons for this substantial change. There was a loss on realization of investments compared with a substantial surplus in recent years. The publication of the Journal once again resulted in a large loss in spite of a generous subvention of R2,000 from the Department of Cultural Affairs and other assistance amounting to R750. The revenue from sales of publications was down considerably. This is a figure which fluctuates considerably from year to year. The secretarial fee was considerably higher than previously. Due to pressure of work it was necessary for the Secretary to relinquish his duties with the Institute of Land Surveyors and, therefore, for this Institute to assume the additional staff costs involved. Finally there was unusual expenditure on the 75th Anniversary celebrations. There was a pleasing increase in revenue from subscriptions, due to the steadily increasing membership, but this was quite inadequate to cover the substantial increases in expenditure and losses in revenue mentioned above. The changes that have been effected in the arrangements for the publication of the Journal have been mentioned elsewhere in this report. It is expected that these will bring about substantial financial benefits in the long term. The MacArthur Forrest Memorial Fund shows an excess of income over expenditure of Rl00 and the total fund was therefore increased by this amount to R4,206. The balance sheet indicates that the market value of quoted shares and debentures increased during the year from R8,755 to R13,059, while the Accumulated Funds now amount to R22,567 as against R24,691 last year. MEMBERSHIP Fifty-six Members, fifty-five Associate Members, thirteen Graduates, twenty-two Affiliates and twenty- nine Students were elected during the year. Twelve Members were admitted to Life Membership; seven Associate Members were transferred to the grade of Member; four Graduates and two Students were transferred to the grade of Associate Member; five Students were transferred to the grade of Graduate; three Affiliates were transferred to the grade of Member; five Affiliates were transferred to the grade of Associate Member. Three Members, seven Associate Members, two Graduates, two Affiliates and six Students were removed from the Membership Roll in terms of By-Law 7.7.1. Your Council records with deep regret the death during the year of the following members: E. F. J. Bulman (Member), E. F. Chapin (Member), R. A. H. Flugge-de-Smidt (Hon. Life Member), T. S. Haldane (Member), J. M. Massie (Associate Member), S. W. Page (Student), S. R. Rabson (Member), M. Ramsay (Member), F. Wartenweiler (Hon. Life Member). A comparative statement of the membership as at 30th June, 1969, and the end of the previous year is shown in the following tabulation: 30th June 30th June 1968 1968 Honorary Life Members 12 10 Honorary Members 6 6 Life Members 176 189 Members 488 514 Associate Members 409 448 Graduates 60 68 Affiliates153 155 Students152 162 1,456 1,552 PAPERS AND JOURNAL The Institute is changing the format of the Journal from the present size to the standard international A4 size with effect from August, 1969. In making this change it will conform to more general practice today in regard to publications and this should effect certain economies and facilitate selling of advertising space. It has been arranged that in future the publication of the Journal, including advertisement sales, will be handled by Kelvin Publications (Pty.) Ltd. who are already doing this work satisfactorily for the Mechanical and Electrical Engineering Institutes. In making these changes the opportunity was taken of redesigning the outer cover of the Journal to incorporate the new coat of arms. The Presidential Address by Mr R. C. J. Goode and twelve papers which were published in the Journal during the year are listed below: August, 1968: Presidential Address: "The Institute-In retrospect and prospect." September, 1968: "Rotary mill liner practice in the South African gold mining industry," by J. H. French and O. E. Lissner.

Careful monitoring of the position of the cave front is essential for well-managed block cave mining. Seismic monitoring systems yield 3-D information about the location of fracturing ahead of the cave. However, because the a seismic gap between cave surface and seismogenic zone is of unknown extent, the cluster of micro-seismicity can only yield an upper bound for the cave height. The large velocity contrast between the fractured rock in the aseismic gap and the broken loose material within the cave can be used by an inversion procedure to find a few simple geometric parameters (such as height of the top of the cave) if a simple 3-D shape?for example a paraboloid?is assumed for the cave. Ray-tracing must be used as the large velocity contrasts cause seismic waves to bend around the cave, but the inversion takes the form of a minimization problem in only a few dimensions and so the computational time is feasible. This technique has been successfully tested on realistic synthetic data.

Jan 1, 2007

By Nicolle Krusberski

Potential errors in XRF analysis are discussed and investigated with specific reference to the analysis of ilmenite samples. A selection of ilmenite samples was chosen and prepared using two XRF preparation techniques: pressed powder pellet and unroasted fusion bead. The merits of the two methods have been discussed in this paper for ilmenite analysis by XRF. Recommendations have been made regarding the use of pressed powder pellets especially with regard to the mineralogical effects that were evidenced during this investigation. The fusion bead technique was found to be far more accurate and able to meet short turnaround requirements provided the calibration methodology used is specific to the grade of samples analyzed.

Jan 1, 2014

O.F.S. Branch, Welkom Minutes of a Committee Meeting held in the V.LP. Lounge of the Welkom Club on Tuesday, 26th June, 1973, at 5.00 p.m. Present Mr C. J. Isaac (in the Chair), Mr D. A. Smith, Mr G. Young,

Jan 1, 1974

By R. Lechuti-Tlhalerwa

"Geometallurgy aims to improve mining project value by predicting the impact that ore and waste characteristics will have on mining and metallurgical processes. This requires integration of rich spatial models of orebody characteristics with validated process response models. These models have, until recently, been constrained by the spatial coverage and representativity of relevant data and the ability to validate predictions made.The revolution in the diversity and volume of data and computational power that is now becoming available for integrated geoscientific modelling of orebodies, and stochastic simulation of mining and mineral processes is accelerating. By embracing emergent integrated data analysis and simulation techniques, geoscientists and engineers can lead a transformation in the way the mining value chain, from orebody to recovery, can be conceived, evaluated, and operated by using the geometallurgical paradigm.This paper describes a methodology that is applied to an existing diamond operation. Analysis of spatial and process data is used to build an integrated geometallurgical value chain model (IGVCM). This IGVCM is used to generate geometallurgical options and evaluate their potential outcomes. The model facilitates the use of flexible, highly configurable, and potentially automated intelligent approaches to evaluate mining and mineral process configuration, and results in more robust design outcomes. The approach described here, and its successful implementation has potential to deliver step-changes in value. IntroductionGeometallurgy aims to identify treatability risks – and opportunities – that arise from the interaction of orebody characteristics with mining and treatment. Improved understanding of the rock/process relationships allows project planners and production teams to predict performance, identify potential shortfalls, and thus enable the proactive creation and evaluation of strategies to mitigate these risks. These advanced insights also create opportunities for continually improving operational performance through dynamically adapting and improving the process response to the changing properties of the ore (Figure 1)."

Apr 1, 2019

By S. J. van Wyk, A. S. H. Haagner, A. Abraha

Opencast coal mining is responsible for the greatest area of land disturbance across all of the commodity types in South Africa. Many thousands of hectares have been rehabilitated to date and, although rehabilitation performance is not always measured or reported, a significant database, spanning 24 years, has now been analysed to identify the main shortcomings holding back rehabilitation sustainability across the industry. Data from 48 different collieries with rehabilitation performance scores measured from 2000-2024 were analysed. A standardised assessment framework was implemented at all 48 collieries, focusing on aspects of land capability, soil fertility, landscape form and drainage, vegetation species composition and basal cover, implementation of maintenance programmes, and prevalence of invasive alien plants. The findings show that, although invasive species management, plant species composition, and plant basal cover are often adequate, the implementation of aftercare and maintenance programmes (influencing soil fertility) and deficiencies in overall landform design and drainage systems are most significant in preventing overall rehabilitation progression and self-sustainability. Integrating these during design and rehabilitation execution, followed by intensive maintenance (especially in the first five years post-topsoiling and seeding) will be key for the overall industry performance to improve to acceptable levels. The database is biased towards collieries that actually do undertake rehabilitation and that do measure it, hence the actual industry performance is likely worse than what is presented. Due to the substantial hectarages involved and the main post-mining land uses being grazing and crop production, the industry cannot afford to keep perpetuating deficiencies in achieving the foundational aspects of rehabilitation that would pave the way for sustained economic future use.

Apr 25, 2025

By M. Arlandi-Rodríguez, and A. García-Berrocal, A. Alonso-Jiménez, C. Lopez-Jimeno

Spain is a major producer of dimension stone, which is one of the most important industrial sectors in the northwest of Spain. This justifies the maintenance of these industries, although the technical and environmental requirements for their continuity are increasingly demanding. The main target of this paper is to present a new methodology in order to obtain k-ratio stress values on the basis of flat jack measurements and finite element numerical back- analysis with Rocscience© RS2 software. Continuous iterations were performed to try to find a relationship between the k₀ and the measured stress in the tunnel roof and sidewalls. It focuses on technical aspects of the method for designing mine chambers in the slate industry that were previously mined by open pit methods. The size of the chambers impacts the operating cost, and the dimensioning of a correct support ensures better efficiency and safety. Correct knowledge of the k₀ therefore is critical for the design of the support. The proposed new method entails a simplification of the classical procedure for estimating the k-ratio.

Sep 1, 2022

By D White, L. Lorenzen

Sampling and metallurgical testwork during various phases of engineering studies is of paramount importance for a robust processing plant design. When developing a process flowsheet, risks in achieving desirable financial outcomes are minimised by ensuring that appropriate sampling and adequate metallurgical testwork support the engineering and cost estimation at each phase of project development. The quality and type of samples used for metallurgical testwork are just as important as the metallurgical testwork itself. The key characteristic required of any sample is that it represents some defined portion of a mineral deposit. Representivity should consider the spatial orientation, lithology, alteration, degree of oxidation, mineralogy, and competency of the ore such as hardness and abrasiveness. Statistically representative sampling procedures and an appropriate metallurgical testwork program should be designed to bring metallurgical understanding up to feasibility study standard and to give a basis for process plant design. The authors have observed that the quality of sampling and quantity of metallurgical testwork carried out during the various phases of engineering studies are often insufficient to truly support a robust plant design. Some designs are based on benchmarks of apparently similar ore bodies or rely on buoyant metal prices supporting cash flows until rectifications can be implemented. The paper will discuss important aspects of sampling and testwork required for engineering studies in designing process plants. Keywords: Sampling, metallurgical testwork, studies, design

Jan 1, 2020

By A. Drumond, J. F. C. L. Costa, M. G. Lemos, A. L. Rodrigues, F. G. Niquini

The past decade has seen a renewed possibility of using machine learning algorithms to solve a large collection of problems in several fields. Data acquisition for mining operations has increased with the growth in sensor-based technologies, and therefore the amount of information available for mining applications has dramatically increased. Ore sorting equipment is available for separating ore from waste based on differences in physical properties detected by a real-time analyser. The separation efficiency depends on the contrast in these properties. In this study we investigate the application of machine learning models trained using data from the output of a dual-energy X-ray ore sorting apparatus at a gold mine. The particles were first hand-sorted into ore and gangue classes based on their mineralogical composition. Classification models were then used to help decide the balance between the number of true and false positives for ore in the concentrate, with a view to economic parameters, using their receiver operator characteristic (ROC) curves. The results showed AUC (area under the ROC curve) scores of up to 0.85 for the classification models and a maximum reward condition Fpr/Tpr around 0.5/0.9 for a simplified economic model.

Aug 8, 2024

By S. Moolla, R. Lynch, S. Brijraj

A reliable method to locate microseismic evets is an important objective for routine mine seismic monitoring. We developed an algorithm that can automatically and reliably locate an event from a single uniaxial trace. Signals created by microseismic events are recorded as seismograms that consist of direct P- and S-waves as well as the waves reflected off the underground excavations. We take advantage of the extra complexity these reflections introduce as they make the signal more unique. In our investigation we cross-correlated unaltered synthetic seismograms against trial waveforms created from a linear combination of appropriate waveforms from a library of numerically calculated strain Green’s tensors. We use a single uniaxial synthetic seismogram to invert for the source location, six moment tensor components, and frequency. The resulting cost functions are constructed as maximal correlations at each node in the mine grid through the true source x-planes. This function is maximized by differential evolution to simultaneously yield the source parameters. Sensitivity tests such as shifting the mine plans and altering the background velocities of the media are investigated to test the robustness of the method. We contaminate the data with 40% white noise to test the resolution against simulated real recorded seismograms. The method is demonstrated using synthetic data calculated with a realistic underground 3D velocity model.

Jun 10, 2024

By A. Santana, J. Jankolovits, G. S. Reyes

The flotation of sulfide ores that contain carbonaceous gangue requires significant operational and chemical intervention to achieve suitable metallurgical outcomes. Carbonaceous gangue dilutes concentrate grades, alters the froth behaviour, reduces operational stability, adsorbs reagents, and reduces value recovery. Carbon management processing strategies like preflotation and depression are often presented as point solutions. Moreover, oversimplified mechanisms of carbon depressants belie their complex and nuanced impact on flotation behaviour. Optimising the flotation of carbonaceous sulfide ores requires a holistic consideration of interactions between the carbon management reagents and the processing strategy, ore mineralogy, flotation behaviour, flowsheet, and all other aspects of the flotation system. Examples are shown where conventional, simplistic mechanisms of carbon depressants fail to explain the observed flotation behaviour. The multifaceted impacts of carbon depressants on froth behaviour, collector performance, and value recovery highlight the need for a holistic approach to carbon management. Keywords: Carbon management, carbonaceous ores, sulfide flotation, carbon depressant

Jan 1, 2020

By A. McQuillan, N. Bar

Geotechnical engineers are routinely tasked with advising suitable stand-off distances below highrisk sections of slopes in open-pit mines that are identified to have potential to deform or collapse. Accurate prediction of failed material runout can mean the difference between continuous safe mining and unwanted high-potential incidents that result in loss of production, equipment damage, injury, or loss of life. This paper updates previous empirical relationships presented by the authors for estimating the volume and runout distance of excavated slope failures, in an open-pit mine operation, using slope geometry as the primary predictor. Cases are sourced from varying slope geometries (fall heights up to 385 m, slope angles up to 80°) and a range of commodities (iron ore, coal, nickel, gold, copper, boron, and limestone), excavated in sedimentary, banded-sedimentary, epithermal, and copper-porphyry deposits, across all six inhabited continents. Analysis of these cases identified positive correlations between slope height and runout distance, and slope height and failed material volume. In general, negative correlations were identified between Fahrböschung angle and slope height, and Fahrböschung angle and failed material volume; however, significant scatter is observed in these datasets. A definitive relationship could not be derived comparing Fahrböschung angle with failed material runout. Slope angle was also found to be a poor indicator of runout. Of the parameters analysed, slope height (i.e., fall height) was found to be the simplest and best predictor of runout distance. This paper presents new charts for predicting failed material runout distance for rock slopes. Relationships are defined for structurally and rock-mass driven slope failure mechanisms at average, 75%, and 95% prediction intervals

Jul 10, 2024

By B. P. Watson, D. P. Roberts, R. A. Lamos

The Upper Group 2 (UG2) chromitite reef is a shallow-dipping stratiform tabular orebody in the South African Bushveld Complex, which strikes for hundreds of kilometres. Mining is extensive, with depths ranging from close-to-surface to 2 500 m. Pillars are widely used to support the open stopes and bords. Little work has been done in the past to determine the strength of pillars on the UG2 Reef and design was done using formulae developed for other hard-rock mines. This has led to oversized pillars with consequent sterilization of ore. In this paper we describe a back-analysis of stable and failed UG2 pillars on the Bushveld platinum mines, and provides a strength formula for UG2 pillars. The formula may be used cautiously on all Bushveld platinum mines with similar geotechnical, geometrical, and geomechanical conditions to the pillars in the database.

Aug 1, 2021

By R. Strydom, J. H. Selby

Published information is available on the radiological impacts of disposing of zircon sand in a landfill. Zircon flour by virtue of its finer particle size presents a different set of issues during disposal. This paper describes two options for disposal of such fine grained materials – namely incorporation into concrete aggregates and agglomeration by addition of cement. The study considers the radiological exposure of the public from such disposal methods and concludes that these options are viable alternatives for the safe disposal of waste zircon flour. The disposal of zircon into concrete aggregates at a rate of 10 per cent produces a sufficiently low effect to allow such aggregates to be used in building foundations or other such mass concrete applications. The use of cement agglomeration methods will also provide a safe method of landfill disposal provided at least 20 cm of soil cover is included.

Jan 1, 2003