Search Documents

By H. Carroll

An ozone detector was built and evaluated for its applicability in smog-chamber studies. The detection method is based on the reaction of ozone with ethylene and the measurement of resultant chemiluminescence. In the first phase of evaluation, the detector's response to ozone was studied as a function of several instrument parameters, and optimum conditions were defined for the maximum and most stable responses to ozone. In subsequent evaluations, the method was checked for sensitivity, precision, and interferences and was compared with two alternative methods. Results showed the chemiluminescence method to be acceptably sensitive and precise for smog-chamber studies and superior to the Mast ozone meter and KI (colorimetric 1 percent neutral-potassium iodide method) methods in that it is specific for ozone.

Jan 1, 1972

By BUREAU OF MINES

The Bureau of Mines in its investigations of respiratory apparatus for use in mines and allied industries, tests equipment that is voluntarily submitted by manufacturers in accordance with published schedules of tests. These tests are designed to insure that the equipment has the minimum require- ments for safety in use. Approval certificates are issued for apparatus that meets the bureau's specifications, and the memfacturer is permitted to mark his equipment with a seal showing that it has been approved as "Permissible." A complete list of permissible self-contained oxygen breathing apparatus, gas masks, and hose masks tested before July 1, 1930, was published in Bureau of Mines Information Circular 6362.1 The present list includes all equipment tested and approved up to and including April 1, 1931.

Sep 1, 1931

This Information Circular from the National Institute for Occupational Safety and Health (NIOSH) documents and supplements the information presented in a series of workshops held during 2002 and 2003. The primary intended audience consists of all who are involved in developing and conducting miners? training. According to the Mine Safety and Health Administration (MSHA), mine operators reported 240,000 full-time equivalent workers and independent contractors reported 42,000 full-time equivalent workers working on mine property during the year 2000. Unfortunately, these workers have a relatively high risk of suffering serious work-related injuries and illnesses. The mining industry has the highest rate of occupational fatalities among all U.S. industries. The fatality rate is 30 deaths per 100,000 workers compared to 4.6 for all private industry(Morbidity and Mortality Week Report, 2001; NIOSH, 2002).Compared to workers in other industries, miners also have a relatively high rate of nonfatal lost-time injuries, and their injuries tend to be more severe (Bureau of Labor Statistics, 1999). Many miners are also exposed to significant health hazards, including coal and silica dust, diesel exhaust, and noise. More than 1000 U.S. miners die of lung disease each year(NIOSH, 1999).

Jan 1, 2002

By Paul E. Loustaunau, Devah Galloway, Catherine Wetherby

This report describes a project in which Development of a Supervisory and Management Training Program for the Underground Coal Mining Industry was developed and evaluated. The project was carried out in two phases. The first phase was a research effort to develop specifications for the program. The second phase was a development and evaluation effort. In the second phase, training programs for first-line supervisors (section foremen) and for middle managers (mine/shift foremen and mine superintendents) were prepared in accordance with the specifications and evaluated by members of the industry. This report describes the project and presents the conclusions drawn there from.

Jan 5, 1983

By Roy Greenfield

During the detection phase, several procedures can be used to improve the signal-to-noise ratio (SIN) . • Subarrays of up to 10 seismometers should be used. The apparent failure to obtain improvement in SIN in the Westinghouse subarrav work is probably due to excessive noise in the electronics. The spacings needed for sensors in the subarray must still be established. • The sensors should be buried. Even burial to a few feet will probably give appreciable reduction of noise. A deeper burial will probably further reduce the noise; and, if the seismometers can be put below the weathered layer, the signal level will probably be increased. The reduction in noise by burial will be especially effective during high noise periods due to wind or rain. • Before attempting detection, the waveforms should be bandpass filtered. The bandpass should go from 25 Hz to an upper frequency of 100 to 200 Hz. Further measurements with a low noise system must be done before the signal-to-noise ratio can be determined for the 100 to 200 Hz range. Any narrow band noise should be removed by notch filters. • If noise levels differ among seismometers of a subarray, weights inversely proportional to the noise power should be applied to the seismometers. • Automatic methods of screening data for possible signal arrivals should be developed, but the final determination that the signal on a subarray output appears to be from a miner should be made by an analyst. Detection of "signal" on several subarrays should be required for positive identification. In the location phase, after detection: • If repeated signals are received, they should be coherently added (stacked) to give as good a SIN as possible for use in determining signal arrival times, to be used in location computations. The miner should, if possible, repeat the signal 25 to 50 times.

Jan 1, 1974

By S. D. Maksimovic

The Bureau of Mines evaluated the hydraulic stimulation of a gob-degasification borehole to determine if this procedure would aid in degasifying a longwall panel. The stimulated borehole did not degasify the longwall panel as expected either before or after mining of the panel started. It reduced the underground methane emission only 11 pct, considerably less than the reductions effected by two unstimulated boreholes in the same panel. Some probable reasons for the reduced methane flow from the hydraulically stimulated borehole are very low reservoir gas pressure, location of hydraulically stimulated zones within the grouted casing, a casing break caused by lateral shifting, possible vertical movement of rock strata during caving, grouting of a 4-inch pipe blocking three stimulated zones, plasticity of shales, and possible hole damage by swelling of water-sensitive minerals. The borehole was also located between two second-mined areas, which may have allowed partial degasification of the overburden and the coalbed in advance of mining. Finally, a period of 3 months is probably not long enough for the borehole to degasify the overburden before mining.

Jan 1, 1977

By Benjamin W. Haynes

The Bureau of Mines conducted research to devise technology for increasing the Nation's mineral supply by recovering valuable constituents from currently discarded waste materials. Municipal solid waste (MSW), presently a major disposal problem, represents a significant source of metals, glass, and a combustible fraction that can be used to supplement coal in generating heat and electricity. As part of the total metallurgical system to treat MSW, this study evaluates the combustible fraction of MSW to characterize the various combustible components and to identify the principal sources of elements that eventually may be objectionable from corrosive or environmental considerations. Several possible sources for cadmium, chromium, cobalt, copper, lead, nickel, and zinc have been tentatively identified. These sources are pigments, inks, paper stock, and additives to plastics. A correlation between industry consumption values and measured concentrations in MSW was found for several elements.

Jan 1, 1978

By Robert R. Stein, Roy C. Bartholomae, William W. Aljoe

This Bureau of Mines report describes in detail the design and operation of a test apparatus for measuring the sound power levels of drills used by the mining industry. The two major components of the test apparatus are a computer-controlled automated drill test fixture (ADTF) and a large (45,000-ft3) reverberation chamber that houses the ADTF. Design specifications and performance capabilities of the ADTF and the reverberation room are given. Initial test results for three types of drills--a pneumatic percussion drill, a hydraulic percussion drill, and a pneumatic rotary drill--are given to illustrate the types of experiments that can be conducted with the test appartus.

By John J. Sammarco

As part of a project to automate coal extraction, computer control of a continuous mining machine test bed has been developed and tested by the Bureau of Mines. A computer system and control software were developed for accurate positioning of the conveyor elevation and swing, stabilizer jack, gathering head, and shear elevation. Tramming actions are also controlled by the computer. The computer system was designed to access data from sensors installed on a continuous miner and to interface with the existing control circuits of the miner. Testing in free space was used to characterize the operation of the machine. From this information, control algorithms were written and stored in the computer. The ability to control each function of the continuous miner with a high degree of accuracy and stability was successfully demonstrated in a series of tests in free space and in mining a block of simulated coal. In the mining of simulated coal, the cutting drum was instructed to position the shearer at the top of the block and shear down to the bottom under closed loop control. The cutting drum came within 0.27 in of the top and within 0.49 in of the bottom of the block for this shearing test.

Jan 1, 1988

By A. May

Florida has accumulated about 400 million tons of phosphogypsum, a mineral process waste generated in the production of fertilizer, and is adding 30 million tons to this annually. To minimize storage of this waste and reduce potential environmental effects, the Bureau of Mines conducted research into utilizing the phosphogypsum, by identifying and developing high-volume uses for this material. Admixtures of phosphogypsum, fly ash, and lime that could produce a coarse aggregate suitable for road construction were investigated. Using phosphogypsum with asphalt, cement, cement-kiln dust, silica, clays, and oxychlorides to pro-duce aggregate was also examined.

Jan 1, 1985

By R. P. Vinson, Abdurrahman Cetinbas, Joseph Cervik, M. G. Zabetakis

The periphery of longwall panels in the Pocahontas No. 3 coalbed is characterized by a zone of reduced permeability that inhibits the natural drainage of methane. A residual gas pressure of 105 psig was measured after 1 year in an isolated block of coal measuring 340 by 1,100 feet. The buildup of gas pressure within such large blocks causes methane problems during plowing operations. However, natural drainage holes drilled during development have been found to reduce the gas content of the coal in this coalbed by over 90 percent. The effect of water infusion on dust during plowing operations was investigated using existing methane drainage holes. These holes were cleaned of debris and a pipe was grouted into the hole for water infusion of the panel. Both total and respirable dust levels were reduced by 40 to 79 percent. Water infusion of the panel proved more effective than did the use of a plow-mounted spray sys tem.

Jan 1, 1974

By Lisa Steiner, Robin Burgess-Limerick

In 2004, underground coal mines in the United States reported 3,405 injuries to the U.S. Mine Safety and Health Administration (MSHA). Of these, 17 percent were associated with the use of bolting machines, 8 percent with continuous miners, and 4 percent each with scoop/load-haul-dump (LHD), shuttle cars and personnel transport. Analysis of the injury narratives identified five hazards that required attention. They are rock falling from supported roof inadvertent or incorrect operation of bolting machine controls, handling continuous miner cable, collisions while driving underground vehicles and driving or traveling in underground vehicles on rough roadways. The rate of lost-time injuries has steadily decreased during the past 10 years (from more than 10 per 100 FTE in 1995, to six in 2004). However, underground coal mining remains a hazardous industry. One of the contributors to this elevated injury risk is working with or near underground coal mining equipment. Roof bolting machines and continuous miners have been consistently identified as high risk equipment. They account for approximately 24 percent of all injuries to underground coal miners (Sanders and Shaw, 1989). LHD's, shuttle cars and personnel transports are also associated with injuries in underground coal mines (Burgess-Limerick, 2005). Conventional analyses of injury statistics typically provide tables detailing the breakdown of injuries by body part nature of injury or mechanism of injury. Such analyses are worthwhile and may be helpful in tracking broad trends over time. Further information is available in the narrative text field completed for each injury reported. The detail contained in these narratives varies. However, they generally provide some insight into the causes of the injury, such as the activity being performed at the tune of

By K. Kar, M. Gautam, J. T. Jurewicz

The 10-mm Dorr-Oliver cyclone has been widely used as a personal sampler for size selective sampling of particles within the respirable range (Dp < 10 gm). Because of their inertia, the particles are unable to follow the swirling flow (outer vortex) within the cyclone. The particles migrate to the bottom of the cyclone, depending on their size, and get trapped into the inner vortex which leads to an eventual blow-off from the top of the cyclone. By measuring the size distribution of the particles in the free stream and in the collected sample, the aspiration efficiency of the cyclone can be calculated. Velocity difference between the free stream and sampling velocity. Inlet orientation, particle impaction and deposition, particle inertia and free stream turbulence result in the departure of the aspiration efficiency from unity and this, in turn, leads to inlet bias. Although the effect of inlet bias on sampling efficiency has been investigated in past, the results lack detailed information and show only some general trend. In this effort, a systematic, in-depth experimental work on the effect of inlet bias on the sampling efficiency has been undertaken using non-intrusive Laser Doppler Anemometry (LDA), Aerodynamic Particle Sizer (APS) and impactors.

Mar 1, 1992

In the interest of safety in metal mining, the Bureau of Mines recommends: That underground metal mines be equipped with a main fan in a fireproof housing, located preferably on the surface. The fan installation should be designed to ventilate the mine adequately throughout and to permit prompt reversal of direction of air flow. Many metal mines depend for ventilation upon natural flow of air, assisted by the exhaust from pneumatic drills and by compressed air blown into the workings. Others also ventilate separate headings or sections with fans and blowers. Relatively few have o mechanical ventilating system that controls the coursing of air throughout the mine.

Jan 1, 1939

By E. H. Denny

The coal and metal mines of the United States furnish this country with a large part of the fuel and material necessary to support our industries and thus make possible the welfare and prosperity of our people and even the continuance of our present-day scale of civilization. Mining companies furnish material to industry with one general purpose in mind -- the making of a profit on their work. Efforts are being made successfully and continually to reduce operating costs, to increase production per man, and to perform work as far as possible mechanically and with more efficiency. These efforts are made primarily to reduce costs, to increase production, or to do both - in other words to make more profits or more certain profits. In the endeavor to reduce expense companies are considering more and more the factors which enter into costs of production, among them the factor of accidents and their cost. This paper endeavors to estimate the approximate cost of accidents to the mining industry in order to present the saving possible through accident reduction or elimination.

Jan 1, 1929

By Robert King

Splicing portable trailing cables used in underground coal mines is usually less expensive in terms of capital outlay and production time lost than replacing them. However, handling trailing cables may result in electrical arcs, shocks , and burns. Also, destructive forces encountered during a mining operation may shorten the effective life of a cable splice. This report gives the results of an analysis of cable splice defects in an effort to establish cable splice performance criteria, determine testing standards for cable splices, establish guidelines for training programs in cable splicing, and indicate areas for improvement.

Jan 1, 1975

By C. E. Brechtel

Cooperative research efforts by the Bureau of Mines and Agapito & Associates, Inc., Grand Junction, CO, used a one-dimensional, finite-element computer model to simulate turbulent mass transfer in face ventilation of oil shale mines. The objective was to study the dilution of methane released by rubbled oil shale during blasting. A methane release rate function was developed from the back-analysis of field measurements, and the finite-element model was calibrated using tracer gas characterization data from tests of full-scale face ventilation systems.

Jan 1, 1989

By R. L. Montgomery

Electronegativities of the rare-earth elements were calculated from heats of formation. The values obtained from different compounds varied widely. The postulates of Pauling&apos;s electronegativity theory were interpreted for bonds that are primarily ionic; the study showed that many compounds obey rules of the form expected. Revised electronegativity values are given for the more electropositive elements, including the rare-earth metals (which are near magnesium in electronegativity). Estimates of un-known heats of formation are made from electronegativities and are compared with other estimates. INTRODUCTION Calculation of the electronegativities of the rare-earth elements is interesting to show how these metals stand relative to the other metals and to each other, and also possibly to systematize the thermochemical data on them.

Jan 1, 1960

By N. S. Dalal, N. Leelarasamee, V. Castranova, K. Van Dyke, V. Vallyathan

"INTRODCICTIONSilicosis is the chronic fibrosing disease of the lungs caused by the inhalation of crystalline silica. However, inhalation of crystalline silica, may induce three distinctly different disease patterns; i.e., chrome silicosis, accelerated silicosis, and acute silicosis. These three disease patterns differ in their pathologic characteristics, clinical symptoms, onset of disease, and mortality. Many studies in the past have focused on the elucidation of mechanisms involved in the development of chrome silicosis. We recently reported that freshly fractured silica has surface properties that could make it more reactive with lung tissue than aged silica, and that this unique reactivity of freshly fractured silica may be involved in the pathogenesis of acute silicosis (Dalal et al., 1986; Vallyathan et al., 1988; Shi et II., 1988). Because freshly fractured silica could contain some moieties in an ""excited state,"" due to the breakage of silicon oxygen bonds, we postulated that the de-excitation of these moieties could produce light which could be monitored by a luminescence measurement technique. In addition, if this ""excited state'' of silica could trigger a greater biologic response by phagocytic cells, this activation could be monitored by a chemiluminescence technique in the presence of appropriate enhancers.This investigation describes for the first time the use of luminescence in the study of freshly fractured silica and its properties. Enhanced biologic reactivity of the freshly fractured silica with alveolar macrophages was monitored by the chemiluminescence technique.MATERIALS AND METHODSNative silica was obtained from the dust bank of the GenericRespirable Dust Technology Center, Pennsylvania State University, State College, PA, and ground for 3~ min in an agate ball mill. It was then sieved through a 20 micron mesh filter and used within 1 O min as fresh silica or stored in glass bottles for aging. X-ray energy spectrometry and X-ray powder diffraction studies on representative samples were made to confirm the mineralogic purity. All the silica samples were found to be 99 % pure with minimal detectable conlamination by metal ions."

Jan 1, 1990

By D. A. Wilson

A process was developed on a laboratory scale in which a solid waste byproduct from refining of secondary lead was converted into three valuable products. Roasted lead blast furnace matte was leached with water to recover copper. This was followed by brine leaching to recover lead. Residues were finally smelted to yield pig iron. Copper was precipitated as cement copper and the lead product obtained was a mixture of pure 3PbO.PbC12.xH20 and Pb(OH)C1. Copper recovery was 89 percent and lead recovery was 96 percent.

Jan 1, 1967