Search Documents

By R. Barany

The heats of formation at 298.15° K of calcium tungstate, calcium molybdate, and magnesium molybdate were determined by solution calorimetry. For the heats of formation from the elements, the values obtained were calcium tungstate, -402.4 ± 0.5 kcal/mole, calcium molybdate, -369.5 ± 0.3 kcal/mole, -334.8 ± 0.2 kcal/mole. For the heats of formation from the oxides J the values obtained were calcium tungstate, -49.2 ± 0.4 kcal/mole, calcium molybdate, -39.6 ± 0.1 kcal/mole, and magnesium molybdate, -12.9 [ ] 0.1 kcal/mole.

Jan 1, 1962

By F. E. Brantley

Optimum autoclaving conditions were determined for separation of iron and manganese values from pregnant leach liquor produced in extracting manganese from low-grade umber are. The umber was leached with a synthetic anolyte similar to a recycle solution, used in manganese electrolysis cell operations, that had been renewed with ferrous sulfate and sulfuric acid. The equipment used and results obtained are presented for the several conditions employed. The kinetics of the separation were studied. Rate equations were derived for the formation of solid ammonium-manganese sulfate, (NH4)2 Mn2 (S04)3.

Jan 1, 1968

By T. O. Llewellyn

Laboratory batch and semicontinuous studies showed the feasibility of using methylene bromide and trichloroethylene in heavy liquid cyclone concentration of a Nevada brucite ore. Cyclone tests of minus 20- plus 200-mesh material at specific gravities of 2.42 and 2.44 recovered 71.6 to 74.9 percent of the MgO at grades of 95.5 and 95.4, respectively. Neither increasing the feed pulp density from 5 to 25 percent solids, nor varying feed pressures from 25 to 60 psig had any apparent effect on the heavy liquid separation.

Jan 1, 1971

By John R. Benham

The Blue Joint Mtn. RARE II area may contain barite resources. One claim, the Woods Creek Barite No. 1, contains two veins of barite of drilling mud quality. The quantity of barite present could not be determined due to limited surface exposures. Sections 1, 2, 11 and 12 of T. 2 S., R. 23 W. in the study area are classified by the U.S. Geological Survey as prospectively valuable for geothermal energy resources. These sections border Blue Joint Creek Hot Springs, which are outside the study area.

Jan 1, 1981

By W. L. Staker

Alternatives were developed to the conventional ammoniacal carbonate leaching-steam stripping procedure for recovering copper as an oxide from contaminated scrap metal. By entraining air bubbles in the leach solution, the copper dissolution rate was increased to 1.5 g/in2 of copper surface per hour, compared to 0.5 g/in2/hr produced by conventional agitation in stirred tanks. Using entrained nitrogen gas bubbles for agitation in conjunction with powdered sulfur not only resulted in rapid dissolution but also simultaneous precipitation of the copper from solution as a high-grade cuprous sulfide.

Jan 1, 1971

By L. C. IlsLey, Charles M. Means

The descriptive rather than the strictly technical meaning of many of the terms and expressions used in the electrical rules is given in order to assist in their interpге- tation . ALIVE . At a potential measurable with a voltmeter and different from that of the earth or another conductor . (Static charges should be determined with an electrostatic voltmeter . This condition may apply to current - carrying parts , to noncurrent - carrying parts and adjacent material where a failure of insulation has taken place , and to objects having stored or static electricity . ) ALTERNATING CURRENT . A current that changes in direction -- positive or negative-- a certain number of times per second , depending upon the number of poles and speed of the generator . AMMETER. An instrument for measuring current , indicating in amperes . AMPERE . A term applied to denote the rate of current flow . ( Analogous to " gallons per minute " in a hydraulic system . ) APPROVED . Accepted as suitable by a competent committee , board , or organization designated by those adopting the rules . ductors . ARMOR . A steel or equivalent metallic covering for one or more electric con- AUTHORIZED PERSON . Anyone commissioned by the official in charge of the mine or his deputies to carry out certain duties incident to the generation , transformation , and distribution or use of electric energy in the mine , such person being one who is competent within the purpose of the rule in which the term is used .

May 1, 1930

By Vernon F. Swanson

Several laboratory flotation tests were conducted by the Bureau of Mines on a sample of unweathered diorite from the B. F. Camden property, Amherst County, Va. Results showed that an ilmenite concentrate analyzing 45.5 percent Ti02 (titania), 0.07 percent P205 (phosphorus pentoxide), and 2.21 percent Si02 (silicon dioxide) could be produced from a feed containing 7.72 percent Ti02 and 3.94 percent P205. Ti02 recovery in the concentrate was 47.6 percent in a batch test. The weathered saprolite material overlying the diorite required scrubbing and desliming to remove argillaceous material and preliminary flotation of apatite followed by flotation of ilmenite. The resulting concentrate analyzed 47.3 percent Ti02, 0.19 percent P205, and 0.99 percent Si02 from a starting feed of 8.99 percent Ti02 and 3.37 percent P205; TiO2 recovery was 54.5 percent.

Jan 1, 1963

By H. J. Heinen

Excellent gold recovery was demonstrated in a laboratory-scale leaching test on waste material from an open-pit mine in northeastern Nevada. An injection system of leaching was applied in which the sodium cyanide solution was introduced into the interior of the dump at selected points. Dissolution of gold from the waste material, which assayed 0.06 ounce gold per ton, was readily achieved because the gold occurred as submicroscopic particles in a porous host rock. Gold recovery of 80 percent was obtained in 11 days from material crushed to 1 inch in size, and recovery was 90 percent after 21 days.

Jan 1, 1969

By C. W. Smith

The Bureau of Mines conducted laboratory-scale beneficiation tests on a sample of corundum gneiss from Montana to devise a method for beneficiating corundum for use as a substitute for refractory-grade bauxite. A flotation process utilizing petroleum sulfonate as the collector in an acid circuit was devised. Results showed that two flotation schemes each produced a concentrate exceeding the national stockpile specifications for calcined bauxite. From a feed containing 28 pct corundum concentrates containing up to 92.5 pct alumina (A1203) were produced with a corundum recovery of 78.5 pct.

Jan 1, 1987

By P. L. Placek

Correlations were made on experimental data for four New Mexico ore series to determine relationships between ore grade and uranium extraction during leaching operations. Such relationships provide information needed to predict the long-range supply of minerals to meet national economic and strategic needs. Results show that other ore constituents and gangue materials in addition to uranium grade influence uranium extraction. In general, tailing grades decrease and uranium extraction increases as both H2S04 and NaCl03 concentrations increase. Terminal emf and terminal pH also were studied. Similar trends appeared for all ores; however, specific combinations of results also were observed for individual ores and ore series. Experimental results indicate that uranium extractions are higher for lower uranium feed grades than predicted by other estimates. Three factors--uranium feed grade, H2SO4 concentration, and NaC103 concentration--were used to design factorial experiments for each ore series. Four additional feed assay factors--V205, Fe, C02, and CaO--were included in regression equations to account for some of the variation in data. The three factorial factors are represented in the regression equations by linear and exponential terms of the form D i'1*G i + Di,2 *e Di, 3*Gi. The four additional assay factors are represented by linear and squared terms of the form Di,*Gi + Di,2*eDi3*Gi. where the Di, ,J are coefficients, the Gi are factors, and the symbol * represents multiplication in computer notation. The interactions of the factors are represented by products of the nonlinear terms for all pairs of the factors.

Jan 1, 1981

By L. A. Haas

The feasibility of removing sulfur dioxide by carbon monoxide reduction in a fixed-bed catalytic reactor was investigated by the Bureau of Mines. The reduction rate of sulfur dioxide with carbon monoxide was significantly dependent upon the iron and alumina content of the mixed catalyst. Maximum catalytic activity was obtained with about 40 percent iron-alumina mixture with a nominal gas mixture of 10 percent carbon monoxide, 5 percent sulfur dioxide, and the balance nitrogen. The synergistic effect of this catalyst mixture was explained by a dual reaction site mechanism, with both iron and alumina augmenting their specific sites at their interparticle contacts. The catalytic activity also increased with decreasing catalyst pellet size. With O.7-mm pellets, the entire pellet appeared to be catalytically active in a 2-gram catalyst bed. The apparent activation energy of the reaction was 18.3 kcal per mole in the temperature range of 350° to 600° C. Carbonyl sulfide (COS) was produced by the interaction of carbon monoxide and sulfur. The amount decreased with decreasing CO concentration. The ratio of COS formed per SO2 removed reached a maximum at about 400° C. The reaction rate appeared to be independent of S02 concentration in the range of 0.2 to 16 percent. The rate, however, increased directly with the CO concentration in the range of 5 to 20 percent. The presence of CO2 (<15 percent) had no appreciable effect on the rate. However, not over 0.5 percent oxygen could be tolerated. This method appears feasible for removing S02 from waste gas if the oxygen is removed prior to the catalytic S02 reduction process.

Jan 1, 1971

By Jr. Sharkey

The Bureau of Mines investigated gases from flash and laser irradiation of Pittsburgh seam (hvab) coal to determine the action of high temperatures on coal. Temperatures in excess of l,000° C were reached with both types of irradiation. Craters about 300 microns in diameter were produced in the coal with millisecond pulses from the laser unit rated at 1.7 joules&apos; output. Gaseous products from laser and flash irradiations in vacuum contained 21 and 8 percent acetylene, respectively. Diacetylene, vinylacetylene, and other products to molecular weight 130 were indicated in the mass spectrum of the gas from the laser study. Single experiments were also conducted in which the laser energy, particle size of the coal, and atmosphere were varied. The results indicated that the distributions of products obtained from the flash and laser irradiations of coal were different from that produced in high-temperature carbonization.

Jan 1, 1966

By K. K. Kelley, L. B. Pankratz

The heat contents of four silicate minerals -- akermanite , cordierite , gehlenite , and merwinite --were measured from 298 ° to around 1,700 ° K by the dropping method . The results were compiled into tabular and equation forms suitable for thermodynamic calculations . The heat contents of these compounds are nearly additive with respect to their constituent oxides .

Jan 1, 1964

By L. B. Pankratz

The heat contents of the sesquioxides of erbium, holmium, thulium, and ytterbium (Er203, Ho203, Tm203, and Yb203) in the cubic crystalline form were measured over the temperature range from 298° to 1,800° K. The erbium and holmium sesquioxides gave regular heat content-temperature curves. Thulium sesquioxide had a minor thermal anomaly near 1,680° K, with a heat absorption of 310 cal/mole; similarly, ytterbium sesquioxide had a minor anomaly near 1,365° K, with a heat absorption of 150 cal/mole. The heat content results are presented in both tabular form (at 100° intervals) and in algebraic form. Entropy increments, corresponding to the tabulated heat content results, also are listed.

Jan 1, 1963

By E. G. King

Enthalpy increments above 298 K were determined by the Bureau of Mines for magnesium hydroxide (brucite) between 298 and 900 K by the method of drop calorimetry. Enthalpy and entropy increments from this investigation were combined with other data from the literature to calculate absolute entropies, free energy functions, enthalpies of formation, Gibbs energies of formation, and equilibrium constants of formation from 298 to 900 K. By the use of published PVT data for water, a table of Gibbs energy change was given for the reaction MgO (periclase) + H2O = Mg(OH)2 (brucite) as a function of temperature and pressure.

Jan 1, 1975

By Nicholas Kyriazi, John P. Shubilla

The National Institute for Occupational Safety and Health, National Personal Protective Technology Laboratory, has undertaken a study to determine how well self-contained self-rescuers (SCSRs), deployed in accordance with Federal regulations (30 CFR 75.1714), hold up in the underground environment with regard to both physical damage and aging. This report presents findings regarding laboratory-tested SCSRs in the seventh phase of testing from May 1999 to August 2000. The SCSRs were tested on human subjects and on a breathing and metabolic simulator. The results indicate that most of the apparatus, if they pass their approved inspection criteria, perform satisfactorily. The deployed CSE SR-100s, however, exhibited significantly higher inhaled carbon dioxide (CO2) levels than new units, as they did in the previous two phases. Several Draeger OXY K-Pluses that rattled when shaken were found to have potassium superoxide (KO2) particles throughout the breathing circuit, including the mouthpiece. Draeger investigated the problem and developed a shake test to detect damaged units. The durations of new Ocenco M-20s were statistically significantly longer than those of deployed units, although only by 2 min.

Jan 3, 2002

By Edward F. Divers

This Bureau of Mines report describes the results of a laboratory evaluation of a mechanical dust collector (scrubber) suitable for underground coal mine applications. The scrubber was developed by the Mining Research and Development Establishment (MRDE), Burton-On-Trent, England, and tested at the Federal Bureau of Mines Pittsburgh Mining and Safety Research Center (PMSRC) as part of a technical exchange program. The 2,000-to 8,000-cfm scrubber consists of an electrically driven vane-axial fan, water sprays, a 2-inch-thick, loosely knit stainless steel wire filter panel, and a water droplet eliminator. The dust-laden airstream travels axially through the water sprays, filter panel, fan, and eliminator. Slurry water drains into a sump where a belt-driven pump recycles it back to the sprays. Fractional breakdown tests showed a maximum dust collection efficiency of 96 pct of respirable-size (less than 7 µm) coal dust at 2,000 cfm. Efficiency decreased with increasing airflow; for example, to 91 pct at 6,000 cfm. Following these tests the original wire panel was replaced with a similar but smaller panel developed at PMSRC; a marked improvement in dust collection occurred at all flow rates tested.

Jan 1, 1979

By P. A. Bloom

Arsenic-containing flue dusts are currently being stockpiled by several nonferrous smelters in the United States. These stockpiles are a source of environmental concern since the dusts can be transported by wind and contain water-soluble arsenic. The stockpiles also represent an alternate source of metals. To provide a quality environment, the Bureau of Mines investigated a process to make environmentally acceptable the discard of arsenic obtained from the treatment of arsenical flue dust. The process includes (1) leaching arsenic from a lead smelter copper dross flue dust, (2) fixing arsenic as an insoluble compound, and (3) recovering other metal values. Overall results of acid-leaching tests on lead-smelter flue dusts showed that H2S04 dissolved 80 to 90 percent of the As, Zn, and Cd, and up to 86 percent of the In. Pb, Ag, and Au remain in the residue, which can be recycled to the smelter. Indium was recovered from the strong acid leach solution by solvent extraction; arsenic was fixed in a stable form by precipitation with Fe2(S04)3 and CaO or CaC03.

Jan 1, 1982

By M. J. Ferrante

The Bureau of Mines determined the enthalpies of Ni3S2 relative to 298.15 K to provide new thermodynamic data for advancement of mineral science and technology. Enthalpies were measured with a copper-block calorimeter from 298.15 to 1,197 K. A solid-solid transition was found at 834±1 K, with an isothermal heat absorption of 13.32 kcal/mol. The temperature of this solid-solid transition was accurately measured by differential scanning calorimetry. Because Ni3S2 does not melt congruently, the heat of fusion of 4.70 kcal/mol was obtained by extrapolation of enthalpy measurements from the solid and liquid phases to approximately 1,064 K. Tabulated values are given for the relative standard enthalpy, heat capacity, entropy, and Gibbs energy function between 298.15 and 1,800 K. Enthalpies are also given in equation form and combined with data from the literature to derive values of standard enthalpies of formation and Gibbs energies of formation. Similar calculations were made for the reaction of crystalline and liquid nickel with gaseous diatomic sulfur for Ni3S-2(c, l).

Jan 1, 1982

By W. H. Eddy

The Bureau of Mines conducted laboratory batch-and small-scale continuous flotation processing tests on waste granite fines from Georgia, to determine the feasibility of recovering usable feldspar and quartz products by flotation. Two flotation methods were utilized for the removal of biotite and other iron-bearing minerals: One was in an acid-cationic circuit, and the other in an alkaline-anionic-cationic circuit. Feldspar was recovered using an acid-cationic method. To produce commercial-grade feldspar and quartz products it was necessary to employ either two sequential froth flotation circuits or one froth flotation circuit supplemented by wet-magnetic separation techniques to remove iron contaminants. Continuous flotation processing yielded a commercial-grade feldspar concentrate containing, in percent, 3.8 Na20, 5.4 K20, and 1.10 CaO, with recoveries of 77.8, 70.3, and 64.4, respectively. The feldspar tailing was high-quality glass sand containing 98.2 percent SiO2 and 0.024 percent Fe2O3. About 42 percent of the quartz was recovered at glass sand specifications. An effective separation of, potash feldspar from the bulk feldspar concentrate was achieved by batch flotation in a mineral separation cell.

Jan 1, 1974