Search Documents

By J. N. Geyer

In coal mining it is essential to maintain the roof over working places and roadways in the safest condition possible. To this end every effort should be made to win the coal with the least injury to the immediate roof strata, as broken strata certainly present a greater hazard than a sound roof. The chief causes of injury to the roof in mining are inherent in the method of development and recovery and the blasting practices followed. The first, which may produce severe stresses in the roof, weakening it over comparatively large areas has been discussed in previous papers3 and will not be treated here. The second cause is local in effect, but with the same general method of blasting being employed throughout a mine having uniform roof conditions, similar effects on the roof may be expected. In the Bureau's investigation of accidents caused by falls of roof and coal it has been necessary to make a careful study of blasting practices and their effect on the immediate roof. The purpose of this paper is to show the effect of the observed methods of blasting on different types of roof and to point out methods that have been proved to be least harmful to the roof strata. The data used in preparing this paper have been compiled from reports made by Bureau engineers engaged in the study of falls of roof and coal, and embrace mines opened in the Pittsburgh coal in Ohio and Pennsylvania and the Pittsburgh and Sewickley coals in West Virginia.

Jan 1, 1933

By N. B. Greninger

The U.S. Bureau of Mines conducted explosion tests on various full-scale cementitious bulkheads used in abandoned mine areas to evaluate the ability of the bulkheads to withstand gas explosion over-pressures of 20 psig. Tests were performed on 120-ft2 solid-concrete-block seals of varying thicknesses and designs. Of the seven solid-concrete-block seals tested, only the standard-type seal, having a 16-in thickness, keyed at the floor and ribs, all joints mortared, wedged at the roof, and a center pilaster, maintained its integrity when subjected to a 20-psig pressure wave. After being subjected to repeated explosions, the standard seal only showed a small hairline crack and had an air leakage of 87 ft3/min at a pressure differential of 1 in H2O. Tests were performed on cementitious foam seals of varying thicknesses and compressive strengths. Explosion tests have shown that 200-psi strength, 4-and 8-ft-thick seals can withstand a 20-psig pressure wave. At a pressure differential of 1 in H20, no air leakage was detected through the 200-psi, 8-ft-thick foam seal.

Jan 1, 2010

By Th. G. Sahama

This paper contains some new heat-of-solution measurements of geikielite (MgTiO3), limonite (FeTiO3), fayalite (Fe2SiO4), and a natural forsterite in mixed acid (HF +HCl) and gives the results of a thermodynamic attack on the problem of stability of geikielite in rocks.

Jan 1, 1949

By Charlie Wyche

Principal mineral products in the Dominion of Fiji were gold, silver, pit and quarry construction materials, and cement. In the years 1978-79, the combined total value of these commodities accounted for some $15 million,2 or 85% of the total mineral output. Production of cement, sand and gravel, and quarry products increased substantially, but gold and silver output from Fiji's only operating metal mine continued the down-ward trend of recent years. Mineral exploration by several international mining companies as well as by local prospectors was being carried out over much of Fiji, and a number of interesting prospects were discovered. One of these, a medium-size porphyry-copper prospect in the Namosi area of Viti Levu, W88 at a mining feasibility study stage. At Mount Kasi on Vanua Levu, an extensive program of geological sampling and mapping W88 being conducted, and surface sampling and drilling W88 taking place at some base metal prospects in the south-central parts of Viti Levu. Also, high gold values in surface samples were reported at Vuda in western Viti Levu.

Jan 1, 1981

By W. P. Yant, R. R. Sayers, G. W. Jones

In the treatment of any illness the early diagnosis is of very great importance . This is especially true in cases of carbon monoxide poisoning , whether acute or sub-acute in character. A diagnosis of CO poisoning is usually made from a correlation of the history , the possible place of exposure , and the symptoms produced . This , however, is not positive evidence because CO often is present in unsuspected places and can be absent in suspected places . Also , the symptoms of this type of poisoning are common to other causes . In many such cases the correct diagnosis may be very difficult , if not impossible by this method and as a result little or no treatment is given . Sub- acute cases , those in which the subject is exposed to concentration sufficient to cause only headaches , malaise , feeling of weakness and dizziness , may be incorrectly diagnosed and as a result , improperly treated . Probably the best method of diagnosis is by examination of the subject's blood . Many methods for the detection of CO in the blood have been developed , but owing to their various individual disadvantages have never come into common usage . Some of the quantitative methods are satisfactory with regard to accuracy but require elaborate and expensive apparatus , special technique and training, or are too delicate and cumbersome for field use . It is of vital importance in all industrial and domestic accidents occuring at places where CO might be suspected or where the symptoms are typical of CO poisoning that a qualitative and preferably a quantitative determination be made the extent of poisoning being of importance in deciding whether CO was the direct or contributary cause) to show the presence or absence of 0. This is indeed essential from a medical standpoint as it aids in prescribing treatment and from a legal standpoint to insure justice in the claims that are often unjustly decided for want of positive evidence.

Jun 1, 1923

By P. Comba

The U.S. Bureau of Mines investigated a hydrochloric (HC1)-calcium fluoride (CaF2) leaching procedure to treat domestic manganese (Mn)-bearing silicate resources. The proposed process is an alternative to high-temperature and energy-intensive extractive techniques. Single-stage leaching with a stoichiometric amount of HCl and a F-Mn mole ratio of 0.2 extracted 96 pct of the Mn when the leach conditions were 50° C, 3 h, and 35 pct solids. Ninety-eight percent of the Mn was extracted during countercurrent leaching at similar conditions. A process flowsheet was developed that incorporated HC1-Cab leaching, excess leach acid utilization, fluoride (F) recycle, and Mn recovery. When the domestic manganese silicate ore was processed, 98 pct of the Mn was extracted, 99 pct of the Cab was reclaimed, and a leach residue was produced that passed the Environmental Protection Agency (EPA) Extraction Procedure (EP) Test for nonhazardous waste.

Jan 1, 2010

By Edmund S. Leaver, Jesse A. Woolf

"The Baboquivari mining district is about 60 miles southwest of Tucson, Ariz., the present railroad shipping point. The values are silver and gold. The silver is largely associated with the black oxides of manganese. The ore is highly oxidized, and careful panning shows only a very small amount of pyrite. Our sample analyzed as follows:A flotation mill has been installed in the district, but it does not concentrate the precious metals satisfactorily. Our best laboratory flotation results were obtained by grinding to pass 65-mesh and floating with Xanthate or standard flotation oils plus sodium sulphide and polysulphide. This sulphidizing method gave a concentration of 32 per cent of the silver and 80 per cent of the gold, which about equals plant practice.We do not know of an instance where the oxidized forms of manganese have been concentrated satisfactorily by flotation.Plain cyanide on the original ore extracts practically all of the gold but only one-third of the silver. A preliminary deoxidizing roast, using producer gas or powdered coal, gives a calcine from which cyanide dissolves about 90 per cent of the gold and 75 per cent of the silver. This method of treatment, known as the Clevenger-Caron process, is described in Bureau of Mines Bulletin 226.Preliminary treatment with sulphur dioxide by burning pyrite or sulphur and passing this gas into the pulp until all of the contained manganese is dissolved or changed in form best prepares the ore for cyanidation. The acid consumption will vary with the percentage of manganese and other soluble constituents. Neither gold or silver is dissolved by this acid treatment. The washed residue gives maximum cyanide dissolution of the gold and silver with minimum loss of cyanide,"

May 1, 1928

By Richard E. Ray, George N. Aul, Fred Garcia, William P. Diamond

Increasing longwall panel dimensions, particularly face width in gassy coalbeds, may result in unexpected increases in methane emissions. To investigate this problem, continuous longwall face emission monitoring studies were conducted at two adjacent mines operating in the Pocahontas No. 3 Coalbed, where longwall faces were to be extended from 229 to 305 m (750 to 1,000 ft). It was predicted by regression analysis of methane emissions data from 229 m (750 ft) wide longwall faces that extending faces to 305 m (1,000 ft) would increase methane emission rates by only 7 percent (0.6 m3/min (20 cfm)), to 8.6 m3/min (304 cfm) at the VP-1 Mine. In contrast, it was predicted that extending faces at the VP-3 Mine could increase methane emissions by as much as 13 percent (1.8 m3/min (65 cfm)) to 16.1 m3/min (567 cfm). The geologic and mine design factors influencing the variation in face emissions between the two mines will be discussed.

By E. J. Kloos

The Bureau of Mines evaluated all previously approved gas masks to determine their ability to provide respiratory protection against each of the following six selected amines: ethylenediamine, diethylamine, n-butylamine, ethylamine, methylamine, and hydrazine. Minimum requirements were a 24-minute service life at a flow rate of 64 liters per minute (32 liters per minute for hydrazine) and an amine concentration of 1.0 volume-percent (0.5 volume- percent for hydrazine). The three masks meeting these requirements were the LG4, Willson Products Division, The Electric Storage Battery Co.; the GMD-SS, Mine Safety Appliances Co.; and the 084-PHOV-R, Acme Protection Equipment Co.

Jan 1, 1966

By E. J. Kloos

The Bureau of Mines evaluated all previously approved gas masks to determine their ability to provide respiratory protection against each of the following six selected amines: ethylenediamine, diethylamine, n-butylamine, ethylamine, methylamine, and hydrazine. Minimum requirements were a 24-minute service life at a flow rate of 64 liters per minute (32 liters per minute for hydrazine) and an amine concentration of 1.0 volume-percent (0.5 volume-percent for hydrazine). The three masks meeting these requirements were the LG4, Willson Products Division, The Electric Storage Battery Co.; the GMD-SS, Mine Safety Appliances Co.; and the 084-PHOV-R, Acme Protection Equipment Co.

Jan 1, 1966

By W. T. Millar

Graphite in the Suffern deposits near Hillburn, N. Y., consists of flakes ranging in size from fines to one-half inch in diameter. The Bureau of Mines investigated the Suffern deposits in the spring of 1943. Gneiss outcrops were examined, and five trenches excavated and sampled. The graphite is not confined to any definite zone but occurs in small, local pockets. Eleven samples were collected and combined for laboratory tests. Tests by the Bureau of Mines indicate that the graphite ore can be beneficiated by stage crushing, "skin flotation" of coarse flakes, and wet flotation of minus 10-mesh flakes. Over 90, percent of the graphite was recovered.

Jan 1, 1949

By D. J. Bauer

Liquid-liquid extraction techniques were investigated by the Federal Bureau of Mines for the fractionation of rare-earth solutions. Separatory funnel work using tri-n-butyl phosphate (TBP) for extracting ceric nitrate from solutions containing sulfate ion resulted in almost complete extraction. Similar tests using primary amines for splitting trivalent rare-earth pairs and fractions gave promising results. The ceric nitrate extraction procedure was scaled-up by use of pressure-bubbler equipment, a series of spray towers for extraction, washing, and stripping. In this case only 84 percent ceric nitrate extraction efficiency was achieved. This work was done using dilute sulfuric acid for stripping.

Jan 1, 1960

By A. B. Hooker, L. C. IlsLey

The greatest hazard of early mining was from explosions of methane ignited by open lights . With the advent of safety lamps and forced ventilation this hazard was greatly reduced until the application of electricity to modern mining not only multiplied the sources of gas ignition but the accompanying , machines and haulage systems increased the amount of explosive dust , through which a methane explosion is more liable to become a major mine disaster , and thus greatly furthered the need of adequate ventilation to keep down the concentrations of methane . Adequate ventilation is still the best preventive of such explosions . However , even with a well laid out and controlled ventilating system the amount of air passing through entries and rooms is liable to vary within wide limits because of open doors , falls of rock , or other accidental causes . The percentages of methane under normal conditions should therefore be kept so small that they will not be increased to explosive proportions by short interruptions in ventilation . Mine ventilation and methane detection are inseparable safety precautions . The increasing importance of ventilation necessitates more accurato determinations of the methane concentrations throughout the mines . This paper discusses in detail some of the steps in the development of methane detection and specially notes the more accurate detectors now available . One of the earliest means of detecting methane was by a candle . About 1835 , John Buddle , Sr. , a noted mining man of his period , when questioned by a Parliamentary Committee as to the safety of using candles , replied :

Jun 1, 1933

By G. L. Oldright, Virgil Miller

"INTRODUCTION The first ten papers of the series on smelting in the lead blast furnace described the operation at the custom smelter of the International Smelting Co., Tooele, Utah, and at the plant of the Bunker Hill Smelting Co., Kellogg, Idaho, which handled a very rich lead concentrate. These previous papers may be considered a picture of the traditional lead smelter treating custom ores and of the smelter that will treat the type of product likely to be made in the future - lead concentrates of an increasingly rich grade.The great plant at Trail is of special interest to those smelting lead products containing much zinc and faced with the necessity of transforming all of their byproducts into commodities which may be sold profitably. The plant is equipped to produce electrolytic zinc, lead, copper, silver, bismuth, and cadmium. Part of the sulphur evolved from treating the ores is converted into sulphuric acid. Complete fertilizers for agricultural purposes are also produced.The smelter of lead ores has long considered that zinc is one of the most difficult ingredients that he has to handle. Even with the gretat improvement in flotation practice today, the residues from electrolytic zinc plants leaching zinc concentrates must still be smelted for their lead content. Of the total gangue material not separated from the lead concentrate sent to the smelter, zinc is still one of the most notable in percentage. The most successful way of coordinating the over-all operations of a concentrator, an electrolytic zinc plant, and a smelter provided with a plant for re-treating the blast-furnace slag for its lead and zinc content must be of interest to many treating complex ores.ACKNOWLEDGMENTThe data in this paper were collected in cooperation with the Consolidated Mining & Smelting Co. of Canada, Limited, and its entire technical staff. Detailed acknowledgments of assistance received are given in the papers from which this one is briefed."

Sep 1, 1934

By Maria I. De Rosa

The major fire and fire injury findings for all metal/nonmetal mining categories for 1990-2001 are shown in tables 64-65. Table 66, partly illustrated in figure 22, shows the number of fires, fire injuries, fire fatalities, risk rates, employees' working hours, and lost workdays for all metal/nonmetal mining categories by time period. For all metal/nonmetal operations (including stone and sand and gravel), a total of 518 fires occurred during 1990-2001; 296 of those fires caused 308 injuries and 4 fatalities (Ewhr = 4,012 x 106 hr, In = 0.015, LWD = 36,204). Thirty fires and 26 injuries involved contractors. The greatest number of fires and fire injuries occurred at surface operations; the highest risk rate values were also calculated for surface operations. The number of fires increased during the first four 2-year time periods (1990-1991, 1992-1993, 1994-1995, and 1996-1997), then decreased during the last two periods (1998-1999 and 2000-2001). The number of injuries showed a decrease throughout the periods, accompanied by an increase in employees' working hours. Twenty-five firefighting interventions by mine rescue teams in underground mines and at least 30 interventions at surface operations were required to combat these fires. However, 45 fires destroyed or heavily damaged facilities and equipment (including 19 pieces of mobile equipment) because of failure of firefighting methods, late fire detection, undetected fires, or fire size. Ninety-seven fires were detected late, and 30 fires were undetected. The ignition sources that caused the greatest number of fires were flame cutting/welding spark/slag/flame (169 fires or 33% with 137 injuries), hydraulic fluid/fuel sprayed onto equipment hot surfaces (89 fires or 17% with 46 injuries and 3 fatalities), heat source/explosion and flammable liquids/ gas/refueling fuel on hot surfaces (98 fires or 19% with 73 injuries), electrical short/arcing (51 fires or 10% with 16 injuries), and spontaneous combustion/hot material (46 fires or 9% with 17 injuries). The flame cutting/welding spark/slag/flame source caused fires usually involving welders' clothing or oxyfuel/grease and other materials (including chute and dust collector liners, flammable liquids, belt material, crusher, hopper and shaker deck materials, washer plants, equipment mechanical components, stampler breaker, hydraulic fluid, rubber tires and hoses, gear boxes, bin feeder, dump rope cables, screen liner and screen panel, kiln and shaft material, pipelines, liquor pumps, wood pallets, electrical junction boxes, handrails, grease, refuse, shop and wood). The spontaneous combustion/hot material and electrical fires were usually detected late due to lack of combustion gas/smoke detection systems. At least 55 of the 89 mobile equipment hydraulic fluid/fuel fires became large fires (requiring 12 mine rescue team interventions in underground

Jan 1, 2004

By Oliver Bowles

It is noteworthy that 80 to 95 per cent of the gross production of all slate quarries in the United States is discarded as waste . In view of the loss involved in handling so much waste , and the consequent added cost of the finished product , the Bureau of Mines has undertaken a study of the slate industry for the purpose of devising the best means of reducing the proportion of waste , and of utilizing the unavoidable waste . The utilization of waste has received special attention , and the cooperation of many prospective purchasers of waste slate has been enlisted in testing its adaptability for various uses .

Mar 1, 1921

By R. E. Perry

In connection with a program of coal research at the Southern Experiment Station the Bureau of Mines, in cooperation with the University of Alabama and the various coal operators, conducts washability studies of coal from beds in Alabama and other Southern States in which commercially important deposits occur. One of the main objectives of a washability study is to obtain technically and commercially important data necessary for determining the best methods for preparing and utilizing the Nation's limited reserves of coking coal. Such information is important to conservation because it facilitates selection of preparation methods that will provide maximum yields of coal with low ash and sulfur contents.

Jan 1, 1958

By Donald P. Schlick

This report presents a representative cross section of methods successfully used to ventilate continuous-miner places as well as various factors that should be considered when selecting auxiliary ventilating equipment. Line brattice can direct fresh air to the active face reasonably well, provided that adequate area for installation is available. Continuous mining equipment, however, often restricts clearances to such an extent that proper installation of line brattice is impossible. Consequently, in many instances face ventilation is inadequate; therefore, many methods of auxiliary ventilation for continuous-mining equipment have been developed and have been discussed in this study.

Jan 1, 1963

By G. E. McElroy, D. Harrington

The use of shall electrically- driven fans , in conjunction with air- pipe of various diameters is becoming of increasing importance for the ventilation of working places in metal mines through which the general ventilating currents can not be coursed . It will probably continue to increase in importance since the concept that air motion is the most important factor in maintaining comfort in hot ( above 80° F . ) working places is more generally accepted , and as the inefficiency and greater expense of attempting to ventilate such places with compressed air is recognized . Managers of large properties can afford to experiment with fan- pipe installations until types are found that meet their conditions , but managers of shall properties , unless forced to it by extreme conditions , prefer to wait until they can obtain data sufficient to guarantee at least a measure of success from such installations . At present , such data , even in part , are available to only a few (mainly fan manufacturer's representatives , consulting ventilation engineers , and ventilatin engineers employed by large companies ) , and important recent developments are mostly of a confidential nature . One large metal - mining company cooperated with a fan manufacturer in some extensive experimental work on small blowers and found that instead of using stock fans , considerable power economy could be effected and equal quantities of air delivered by use of or 2/3 width fans with small motors rather than using stock fans and larger motors ; it was also found advisable to adopt certain sizes of tubing for certain lengths of run . In fact , many important facts were ascertained in this study , and it is now promised that they will soon be given to the public . It is true that a certain amount of data on industrial installations are available , but such data are only in part applicable to metal -mine conditions , because , until recently , little attention has been given to ventilation in metalmines , and the conditions encountered usually require a greater length of pipe , a more temporary type of construction , and closer attention to temperature control than the ordinary run of industrial installations demands ..

Feb 1, 1922

By H. O. McDonald

The Bureau of Mines reviewed the chemical vapor deposition (CVD) literature on the nonmetal binary and ternary compounds of the group IVB, VB, and VIB elements, with emphasis directed to the following nonmetals: B, C, N, O, and Si. This review examines each of these binary and selected ternary compounds of the group IVB, VB, and VIB elements as coatings and gives some of their preparative methods, uses, and properties. A total of 259 references were found for these compounds of the nine elements. This review was utilized in the Bureau's research to provide abrasion-, erosion-, and corrosion-resistant coatings in order to conserve critical metals and protect various metallic surfaces in metallurgical, mining, and energy conversion systems.

Jan 1, 1983