Search Documents

By Jos. R. Guiteras

This paper describes the pumping operations at the Ajax, Cresson, and Vindicator dines in the Cripple Creek mining district of Colorado during the summer of 1936. At that time the three mines wore pumping 6,500 gallons of water per minute into the Roosevelt drainage tunnel. Cripple Creek is the most important gold district in the State; it has yielded gold valued at over $365,000,000. The mines engaged in pumping are among the largest producing properties in the district. ACKNOWLEDGMENTS The author wishes to acknowledge the friendly cooperation of mine officials at the properties visited. At the. Ajax mine information was courteously given by Clayton Kissel, mine superintendent, and his staff; R. Y. Roby contributed the drawings. For information on the Cresson mine, thanks are expressed to Al H. Bebee, mine superintendent, and his staff, especially to Guy Rorabaugh, master mechanic, and to engineer Carlton. At the Vindicator mine, J. S. Anderson; mine superintendent, and Robert Welch, master mechanic, assisted; the latter furnished most of the information about that mine. Acknowledgment is also made of the cooperation of M. H. Salsbury, engineer at the Portland mine, who supplied technical data on the Roosevelt drainage tunnel.

Jan 1, 1937

By R. V. Lundquist, H. Leitch

Two hydrated calcium aluminates , formed by side reactions in the leaching step and desilication step of the lime- soda sinter process , were investigated to better define their influence on alumina recovery . The two calcium aluminates , Caз [ Al ( OH) 6 ]₂ and зCa0.Al½ 03 · ( 8-12 ) H₂ ) , were prepared and identified by chemical and X- ray analysis . The relative proportions of each of these compounds formed in typical leach solutions at several temperatures were determined . The influence of free lime as a promoter of calcium aluminate formation was also investigated . The formation and precipitation from leach liquors of calcium aluminates contributes to the low alumina recoveries in the process . The presence of carbonate ion in the leach solution suppresses calcium aluminate formation and precipitation and results in higher alumina recovery . Hydrated calcium aluminates are formed in the aging of lime - soda sinters in the normal atmosphere .

Jan 1, 1963

By Frank G. Horino

The Bureau of Mines studied the uniaxial compressive strength of model rock pillars as a function of the angle and spacing of noncohesive planes of weakness. The model pillars were prepared from NX 2-l/8-inch diameter drill core of limestone, sandstone, and granite, and the planes of weakness were diamond saw cuts ground flat and smooth. The angle of the planes of weakness, measured from the horizontal, varied from zero to 57° in approximately 15° increments. When two planes of weakness were used, the thickness-to-diameter ratio of the wafer was 1/4, 1/2, and 1, Approximately 400 model pillars were tested in uniaxial compression. The results indicate that the uniaxial compressive strength of model pillars decreases rapidly as the angle of the plane of weakness increases from 30° to 57°, and that the spacing of these planes of weakness has only a minor effect on the strength. The effect of the number of horizontal planes of weakness, with a spacing of 1/4 and 1/2 of the diameter, upon the compressive strength of model pillars was also investigated. These results indicate that as the number of planes of weakness increases the compressive strength of the pillar decreases. Normalizing the data provides useful estimates of model pillar strengths for any rock type.

Jan 1, 1968

By E. K. Kleespies

The rate of the heterogeneous reaction between titanium-oxygen solid solutions and titanium trichloride in molten sodium chloride was determined at high temperatures. In the alpha phase, the reaction rate decreases uniformly with the increasing concentration of oxygen. The gamma crystalline form of titanium (above 33 atomic percent oxygen) was much less reactive than the alpha phase, and the reaction rate approached zero at 50 atomic percent oxygen. The activation energy for the reaction of titanium-oxygen solution containing 22.8 percent oxygen was 11.7 kcal/mole of TiCl3 as compared with 8.3 kcal/mole of TiCl3 for pure titanium.

Jan 1, 1967

By Ann G. Kim

Hydrocarbon gases, primarily methane but also the C2 through C5 paraffins, the C2 and C3 olefins and possibly the C4 and C5 olefins, are byproducts of coal formation. Although it is generally believed that coal formation occurred at temperatures below 200° C, most experimental work on gas formation from coal has been performed at temperatures between 200° and 1,000°C. The objective of this Bureau of Mines experiment was to determine if observable changes in the gases from coal could be produced at temperatures below 200° C in relatively short periods of time. The experiment involved heating coal samples from six coalbeds at constant temperatures and analyzing evolved gases. The composition of the gases at three temperatures was compared. At 35° C, over 99 pct of the gas is methane; at 125° and 150°, methane constitutes approximately half of the hydrocarbon gas. Isobutane and pentane are the predominant higher hydrocarbons at temperatures between 100° and 150° C.

Jan 1, 1974

By Glen C. Ware

The Bureau of Mines determined the factors involved in the corrosion of starting sheets used in the production of electrolytic zinc with the ultimate purpose of adapting zinc starting sheets to commercial practice . Under present practice , zinc is electrodeposited on aluminum cathodes and subsequently stripped for melting . The use of zinc instead of aluminum would eliminate the need to strip the deposit , thereby reducing the cost of handling and melting it , but zinc has not been suitable because it was too vulnerable to the corrosive attack of the electrolyte . Serious attack was found to be limited to the areas of the cathodes situated immediately above the surface of the electrolyte and to re - entrant corners . It was possible to avoid solution - level corrosion by immersing the starting sheets completely , exposing only a relatively heavy suspension member to solution - level attack . Zinc starting sheets could be made as reliable as aluminum and could be continued in residence for periods up to 39 days . Periods as long as a week were feasible under conditions similar to those found in commercial practice . A test of zirconium as a starting - sheet material showed that it promoted corrosion of the deposit to a lesser extent than aluminum and that the deposit adhered less tenaciously . These two properties lend themselves to the development of ways to strip deposits mechanically from zirconium starting sheets . Titanium was unsuitable for use as a starting - sheet material .

Jan 1, 1963

By Dennis Dolinar, Christopher Mark, Gregory M. Molinda

In 1999, 2,087 unplanned roof falls were reported from 841 mines. Nearly 55% of all mines reported at least one roof fall, and nearly 17% of the mines reported five or more falls. In order to investigate the variables that contribute to roof falls, the National Institute for Occupational Safety and Health (NIOSH) compiled a national database of roof performance from 37 coal mines. Geotechnical factors and their effect on roof fall rates were compiled from over 1,500 miles of drivage. The factor that is the best predictor of roof fall rate is the Coal Mine Roof Rating (CMRR). For a low CMRR (#30), almost all cases have high roof fall rates. Conversely, high roof fall rates are rare for strong roof rocks (CMRR $ 60). Roof fall rates were also higher in deeper mines, probably because of greater stresses. Intersections were much more likely to fall than roadways, and four-way intersections were more prone to fall than three-way intersections. In a controlled comparison of the effect of increasing bolt length on roof fall rates, it was found that longer bolts reduced the roof fall rates in 11 of 13 cases. A relationship between the roof fall rate, the intersection span, and the CMRR was also found. Finally, a systematic method for tracking roof performance and geotechnical variables was demonstrated.

Jan 10, 2000

By R. V. Ramani, P. M. T. White, D. Sutton

This review of literature is centered around ore evaluation and reserve calculations as generally used in the mining industry. Methods of data interpolation were reviewed with the object of determining a method that would best suit the evaluation of under- ground coal deposits. Further, computerized data library concepts as related to geological data were investigated together with a brief evaluation of the data requirements for the total project. Additionally, computer techniques for the processing of geological data with a view to generate management information for decision making were reviewed including hardware and software availability. 2.1 Interpolation and Extrapolation of Data The importance of accurate estimates of value parameters in terms of their geographical and geological distribution within a, mineralized body has long been recognized in the evaluation of metallic and non-metallic deposits. As the factors which affect mineral distributions and associations are better understood, accuracy, and reliability of estimation increases. The ideal objective is to develop a deterministic model with the capability of accurately predicting the value at any geographical location. The most important value parameters requiring determination in any orebody are the grade and the quantity of ore that can be mined at the stated grade. These two parameters are modified or qualified by others which include physical dimensions and physical and chemical characteristics of the ore value. Therefore, the

Jan 1, 1974

By Victor Himel

This report documents a systematic approach towards implementing an improved ensemble for the mine rescue team system that will protect against the hazards of mine rescue and recovery and will also afford improved performance through increased comfort and maneuverability, lighter burdens, and improved human engineering designs. In the first part (Task 1) the mine rescue team's protective needs were defined along with the test methods required to evaluate whether a particular piece of gear met these needs. Task 2 assessed existing gear against performance criteria and standards developed in Task 1. Task 3 consisted of the conceptual design and construction phases of the MRPE program. Special consideration was given to advanced concepts, materials, and equipment.

Jan 1, 1982

By Irving Hartmann

The Bureau of Minas has been charged by the Congress with the responsibility for administrating the provisions of the Federal Coal-Mine Safety Act. One of the important duties of bureau inspectors under this act is to determine whether proper measures are taken to prevent mine explosions, which in moat miner includes Judea adequate rock dusting The investigation made after the explosion in Orient No. 2 mine, December 21, 1951, showed that much information is lacking on the adequacy of current rock-dusting and duet-sampling practices in the United States. To obtain such information, an intensive sampling survey was conducted by the Bureau in an Indiana coal mine. This paper summarizes the more Important findings from this survey, describes special samplings at several Pennsylvania coal miners, and discusses related studies in the Bureau's Experimental coal mine.

Jan 1, 1954

By J. V. Batty

The Bureau of Mines devised techniques involving the use of beta-and gamma-ray-emitting radioisotopes and successfully adapted these techniques to the density of mineralized flotation froths) the rate of flow of finely ground ore pulps) and the residence time of pulps in processing circuits. Specifically, the water and mineral loads of flotation froths were continuously measured by determining the proportion of a constant-strength beam of beta rays that was absorbed by the froth column. Continuous measurement of the rate of flow of an ore pulp was accomplished by measuring the changing width of a free-falling stream of the pulp with a collimated beam of beta rays. The residence time of solids in conditioning and resin-in-pulp circuits was accurately measured by following the progress through these circuits of a portion of the pulp that had been tagged with the gamma-emitting Ag110 radioisotope.

Jan 1, 1966

By D. H. Zellers

Since its inception the United States Bureau of Mines has fostered the development of portable mine lamps. Although there is still much to be desired with respect to illumination in coal and metal mines and the replacement of open lights has been slow the Bureau has been given credit for assisting materially in the development and introduction of the safe and efficient portable mine-lighting equipment available today. Much of the work conducted by the electrical section of the Bureau entails approval tests of various types of electrical equipment, including lamps; to be used in atmospheres that may contain methane or coal dust in explosive proportion. If a can lamp meets the requirements-for safety, efficiency, and adequacy, as published in Schedule 6B,4 it is approved and is generally known as a "permissible" lamp. The terms "approved" and '"permissible' often are used interchangeably. The manufacturer must put an approval plate on each approved lamp, showing it has mot the schedule requirements. The approval plate is not a guarantee that the lamp is safe. However, if the lamp, once in service, has not had any parts changed or improperly assembled or if carts that wear out or depreciate have been properly replaced it should still, be safe, efficient, and adequate for the service intended. Virtually all electric cap lamps in service today in the United States and a great many that have been sent to foreign countries bear the approval plate of the United States Bureau of Mines. Although many explosions have been attributed to open lights none has been charged against the permissible cap lamp. Nystagmus, a disease of the eye attributed to working under insufficient illumination, is practically unknown among; American miners, although it is quite prevalent among European miners.

Jan 1, 1935

By C. W. Davis, M. W. Von Bernewitz, S. C. Lind

During the past few years our possible domestic resources of platinum have attracted much attention . On account of the extensive use of platinum during the World War , and the practical elimination of the Russian supply , the price of this metal rose to new high levels , as shown in Table 1 ; and though it since receded to some extent , the price is now nearly six times that of gold .

Jun 1, 1923

By Arthur L. Miller

Recent studies suggest that trace metals emitted by internal combustion engines are derived mainly from combustion of lubrication oil. This hypothesis was examined by investigation of the formation of particulate matter emitted from an internal combustion engine in the absence of fuel-derived soot. Emissions from a modified CAT 3304 diesel engine fueled with hydrogen gas were characterized. The role of organic carbon and metals from lubrication oil on particle formation was investigated under selected engine conditions. The engine produced exhaust aerosol with log normal-size distributions and particle concentrations between 105 and 101 cm-3 with geometric mean diameters from 18 to 31 nm. The particles contained organic carbon, little or no elemental carbon, and a much larger percentage of metals than particles from diesel engines. The maximum total carbon emission rate was estimated at 1.08 g h-1, which is much lower than the emission rate of the original diesel engine. There was also evidence that less volatile elements, such as iron, self-nucleated to form nanoparticles, some of which survive the coagulation process.

Jan 1, 2007

By T. H. Jeffers

To help maintain an adequate supply of minerals to meet national, economic, and strategic needs, the Bureau of Mines investigated the feasibility of extracting copper from coarse native copper ore with ammoniacal ammonium carbonate solution by a simulated in situ leaching procedure. A 5.9-metric-ton (6.5-ton) sample of minus 30.5-centimeter (12-inch) conglomerate-type ore analyzing 1.96 percent copper was leached in a column for 556 days with a solu-tion that contained, in grams per liter, 2.2 NBs and 1.9 CO[3=]. The copper extraction was 71.4 percent, and reagent consumptions were, in kilograms per metric ton of ore, 1.1 NBs and 0.85 CO[3=] (in pounds per ton of ore, 2.2 NH3 and 1.7 CO[3=]). The pregnant leach solutions contained about 1.4 grams per liter copper, which was readily extracted from these low-tenor liquors with a 1:19 mixture of an organic extractant and kerosine. Copper was stripped from the loaded organic with depleted electrolyte containing 150 grams per liter H2S04, and the copper was recovered by electrowinning with antimonial lead anodes. Conditions also were established for minimal lead transfer to the cathode copper.

Jan 1, 1979

By J. F. McIlwain

As part of its goal to minimize the requirements for critical materials, the Federal Bureau of Mines has investigated the consolidation of an iron-base superalloy (20 pct Cr, 5 pct each Ni and Mn, 1 pct each C, W, Mo, and Cb, and the balance Fe) and its modifications by powder metallurgy (P/M) techniques. Vacuum-atomized, prealloyed powder was used. Consolidation was by sintering of cold-pressed alloy powder, or by forging plus rolling or extrusion of canned powder. Several commercial lubricants were evaluated in the pressing operation. At 50-tsi compacting pressure with up to 3 wt-pct lubricant, green strengths did not exceed 1,000 psi. Powder sintered just below the solidus temperature attained a tensile strength of 69,000 psi and 4 pct elongation. Liquid-phase sintering produced higher densities, lower tensile strengths, and nil ductility. Canned powder was forged and rolled at 1,200° C, yielding a 100-hr rup¬ture strength of 9,800 psi at 815° C and a room-temperature tensile strength of >130,000 psi at 6 pct elongation. Heat treatment of modified P/M iron-base alloy containing 0.63 pct C resulted in a 100-hr rupture strength of 17,000 psi. Oxidation resistance at 805° to 815° C of the forged and rolled P/M iron-base alloy was similar to that of the cast iron-base alloy and supe¬rior to conventional stainless steels.

Jan 1, 1981

By Charles E. Whieldon, C. I. Pierce

Data on the oilfields in Mahoning , Columbiana , Carroll , Jefferson , and Harrison Counties , Ohio , were collected from scattered sources and compiled to make the information readily available to operators who may be interested in conducting secondary - recovery operations in the area . General geology , oil production , oil - productive acreage , core data , reservoir calculations by townships , and miscellaneous data and reference material are presented .

Jan 1, 1965

By Dennis R. Dolinar

The National Institute for Occupational Safety and Health?s Pittsburgh Research Laboratory conducted a full-scale test of a composite polyurethane-aggregate seal in a hydrostatic chamber at the Lake Lynn Experimental Mine. This composite seal consisted of a polyurethane and limestone aggregate core that was formed between two concrete block walls. In the hydro-static chamber test, water is used to pressurize the seal. During the test, the maximum average water pressure the seal was able to withstand was 18.9 psi. Further, the seal began to yield at an average water pressure of only 17 psi. At the time of the test, the minimum seal design requirement was 20 psi under 30 CFR4 75.335 (2005). Therefore, based on this test, the seal did not meet the regulatory minimum design requirement. Uniaxial compressive tests conducted on samples from the polyurethane-aggregate core revealed that both the compressive strength and the elastic modulus of the material were much less than that for polyurethane only with a density of 10.0?12.0 lb/ft3. The significant reduction in the strength and stiffness of the polyurethane-aggregate mixture results from the formation of a soft polyurethane foam around each piece of aggregate. The formation of the soft foam seems to be caused by residual moisture from the aggregate. The moisture also caused the density of the polyurethane in the polyurethane-aggregate mixture to be less than the design requirements. The lower density of the polyurethane in the mixture, along with the formation of zones of pure polyurethane only, resulted in the overall seal density being less than the design requirements. During seal construction, steps were taken to control the moisture, but were not successful. An analysis of the seal failure showed that the calculated shear stresses at failure and the estimated shear strength of the polyurethane-aggregate mixture are fairly close. This suggests that the strength properties of the polyurethane-aggregate mixture along with a weak zone of poorly bonded aggregate controlled the maximum pressure the seal could withstand. At the time of the seal testing, the minimum design requirement was 20 psi, as specified at 30 CFR 75.335 (2005). New emergency temporary standards for seal designs were promulgated on May 22, 2007, with a minimum requirement of 50 psi under specified conditions. However, it will be shown that the evaluation of the polyurethane seal performance as designed to meet the older 20-psi criterion can be relevant to the design requirements under the new standards.

Jan 1, 2008

By L. C. IlsLey

The United States Bureau of clines has been conducting Investigations of electrical equipment during a period of more than 25 years in an endeavor to encourage the development of safer electrical equipment for coal mines. In order to conduct these investigations in an orderly manner they are carried out under a published schedule of tests known as Schedule 2C, which specifies detailed requirements for motors, controllers, etc., and fees covering the various inspections and tests made as part of a routine investigation.

Jan 1, 1937

By Kenneth M. Earl

This report describes the results of a field study conducted by the Bureau of Mines during 1956 and 1957 on manganese-and iron-bearing mineral deposits in the southern district of Aroostook County, Maine. The work was undertaken to determine the extent of deposits largely concealed under glacial drift and to obtain subsurface samples for manganese mineral identification and research in ore dressing and extractive metallurgy. The investigation was confined to the Westford Hill-Daggett Hill area in Hodgdon Township and to the Stewart prospects and vicinity in Linneus Township. Over 50 magnetic anomalies were mapped by magnetometric surveys in the Westford Hill-Daggett Hill area, Hodgdon Township. The largest anomaly, as outlined by the 1,000-gamma contour, indicates a deposit 3,200 feet long with a maximum width of 350 feet. The smallest anomaly measures about 10 feet wide by 25 feet long.

Jan 1, 1962