Search Documents

By G. W. Jones, F. E. Scott

"INTRODUCTION During the last war, considerable attention was given to the search for materials or combinations of materials for use as expelling agents for aerosols in the well-known ""aerosol bomb."" These materials must be free of fire and explosion hazards under normal conditions of use.In cooperation with the Department of Agriculture and other Federal agencies interested in the work, the Bureau of Mines carried out a laboratory investigation on the inflammability of- dimethyl ether-dichlorodifluoromethane air mixtures. 4/The method of investigation was essentially the same as that used in a similar investigation dealing with the inflammability of propane-butane-dichlorodifluoromethane mixtures. 4/SOURCE OF MATERIALSThe dichlorodifluoromethane (commonly known as freon-12) and the dimethyl ether were supplied by Dr. Lyle D. Goodhue., U. S. Department of Agriculture, Beltsville, Md. It was reported that the freon-12 was manufactured by the Kinetic Chemical Co. Wilmington, Del., and the dimethyl ether by the Carbide & Carbon Chemicals Corp., Charleston, W. Va..The materials were obtained in small metal cylinders and were used as received. Before using, the cylinders mere placed in an upright position, and 5 to 6 liters of the gas was released from each cylinder to the atmosphere to remove any trapped air that may have been introduced when the cylinders were filled."

Sep 1, 1947

By Robert F. Chaiken

More than 500 fires are now burning in abandoned coal waste banks and coal deposits in the United States. Once established, such fires can burn for decades, and extinguishing them by conventional methods such as surface sealing to exclude air, excavation to remove fuel, or flushing to cool the fire zone is usually difficult and always expensive. Burnout Control, a technique developed by the Bureau of Mines for the control of abandoned coal fires, involves the accelerated combustion of coal in place with total management of the heat and fumes produced. A burning waste bank or mine is placed under negative pressure relative to the atmosphere, and heat and combustion products are drawn from the combustion zone through an exhaust ventilation system. Heat produced appears as sensible heat in the exhaust, at temperatures as high as 1,000° C (1,832° F), and could be recovered for the production of steam, hot water, process heat, or electricity. The Bureau's first field demonstration of Burnout Control was at Calamity Hollow in Allegheny County, PA (near Pittsburgh). Calamity Hollow was the site of an underground mine in the. 1900's and was surface mined in the 1940's. In the winter of 1961~62, a fire of undetermined origin was discovered in the exposed coal. In 1963, the Bureau constructed a trench barrier around the fire and a surface seal over the affected area. The fire was isolated but, not completely extinguished. In 1979, when the Bureau began work on the Calamity Hollow Mine Fire Project to demonstrate controlled burnout, the fire was still smoldering on the hot side of the trench barrier. The project, which was begun in December 1979 and ended in July 1982, consisted of the design, construction, operation, and subsequent dismantling of a Burnout Control ventilation system. This report, although considered part 2, is actually the last of a five-part series that describes the Calamity Hollow Mine Fire Project. It was written last because it involved the analysis of a substantial body of data describing in detail the results of a continuous 4-month burnout operation. The first report, part 1, describes the design and construction of the field installation. Part 3 describes the instrumentation used to control and monitor the progress of the burnout operation. Parts 4 and 5 deal with the closeout phase of the field demonstration. Part 4 describes the procedure used to quench the fire, and part 5 describes the final excavation and backfilling of the heated zones. The reports in this series document the Calamity Hollow controlled burnout demonstration, which showed that (1) controlled in situ combustion is a feasible method for controlling underground fires in abandoned mines, (2) the resultant thermal exhaust output is suffIcient for energy utilization, and (3) water injection-fume exhaustion is a potentially effective method for cooling large underground fire zones. Further investigations of both Burnout Control and the water injection-fume exhaustion quenching procedure are planned.

Jan 1, 1989

By M. L. Whisman

Radiotracer techniques were developed for stoichiometric studies of photochemical reactions associated with atmospheric smog formation. Stock blends of separate hydrocarbon and oxygenated compounds were prepared and calibrated. 14C-labeled reactants and products in reaction systems involving hydrocarbons and nitrogen oxides at the ppm level were analyzed for qualitative and quantitative data. Precision and accuracy of these methods developed by the Bureau were determined by replication and statistical treatment of data, and these methods are described.

Jan 1, 1969

By R. A. Meyer

A table that greatly simplifies determination of metastable transitions in mass spectra has been prepared. All the mathematically possible metastable transitions of any compound whose molecular weight lies between 26 and 150 can be determined from the table without calculation. The method of utilizing the table is described, using selected peaks from the spectrum of normal butane for illustration. In the mass spectrometer, ions are formed in the isatron and accelerated through a series of slits. Most of these ions reach the collector without further change, but a few dissociate in transit to form new ions. These ions appear in the mass spectrum at neither the mass--to-charge ratio (m/e) of the original ion nor that of the new ion. A formula that relates the appearance of these new ions to the ion from which they were formed is: [ ]

Jan 1, 1957

By J. G. Croeni

The high thermal-neutron cross section of gadolinium and the good mechanical and corrosion properties of titanium suggest that alloys of these two metals might be useful as control rod material. To aid in establishing the feasibility of this combination, the Federal Bureau of Mines investigated the titanium-gadolinium system. The results indicate that the system is composed of a single eutectic reaction and a peritectoid reaction involving the alpha-beta transformation of titanium. The eutectic isotherm extends from 1 to 99 pct, gadolinium at 1,240° C. The established eutectic composition is about 95 pct, gadolinium. The peritectoid reaction occurs at 885° C. and extends almost over the entire composition range. Hardness increases slightly with additions of gadolinium, and little change is obtained by heat treatment. Alloys containing less than 10 pct. gadolinium are amenable to extensive cold-working, but alloys having higher percentage of gadolinium content are only moderately cold-workable. All alloys can be hot-worked in iron sheathing at 750° C. Observation indicates that all compositions possess good machinability. Corrosion resistance to water at room temperature is apparently poor, especially in the gadolinium-rich alloys. INTRODUCTION A combination of the good mechanical and corrosion properties of titanium and the variety of thermal-neutron cross sections characteristic of the rare-earth metals suggests that alloys of these metals may be used for control rod materials. For this reason the Bureau of Mines proposed a study of the titanium-gadolinium alloy system, and the Atomic Energy Commission sponsored the investigation.

Jan 1, 1961

By R. G. Meara, O&apos

The land-pebble district of Florida, wnich in 1928 supplied 96.7 per cent of the phosphate production of that State and 82 per cent of the domestic requirements of the United States, is centered in Polk and Hillsboro Counties about 30 miles east of Tampa The deposits are unconsolidated sediments occurring as beds of phosphate matrix overlain by a mantle of barren sands and clays. The matrix consists of a mixture of sand (quartz grains), clay, and phosphate rock in which the coarsest sand is much finer than the coarsest phosphate; that is, the sand is segregated in the fine material. Before the introduction of classifiers the concentration consisted of log washing, and screening at about 20-mesh, which was usually the finest size that could be taken to maintain commercial grade, 66 per cent B. P. L. (bone phosphate of lime) or more. When classifiers were introduced some of the fines that had escaped at the head of the washery and some of the minus 20-mesh material isolated during the washing and formerly lost supplied the feed. During October, 1927, the United States Bureau of Mines in cooperation with the University of Alabama and the Missouri School of Mines and Metallurgy began to investigate the amenability of phosphatic sands to gravity methods of concentration. The work was under the immediate supervision of B. W. Gandrud, acting supervising engineer of the Southern Experiment Station of the U. S. Bureau of Mines at Tuscaloosa, Ala., and Will H. Coghill, supervising engineer of the ore dressing section of the U. S. Bureau of Mines. More comprehensive testing followed and in the early part of 1930 some of the companies cooperated with the bureau and the above-mentioned institutions in conducting a series of tests on hydraulic classification and tabling. The results indicated that marketable concentrates could be obtained with a recovery of 25 to 45 per cent of the phosphate formerly lost. As a result two companies have introduced hydraulic classification to treat the current tailings, and one of them has substituted classifiers for the 20-mesh screens which had been unsatisfactory. Because the phosphate grains and quartz grains have nearly the same specific gravity, the use of concentrating tables by the customary methods is not applicable. The washeries included in the following report are designated as Nos. 1, 2, and 3.

Jan 1, 1931

The first phase of our work for PMSRC on this contract was devoted to a comprehensive and in-depth assessment of electromagnetic (EM) noise measurements and data taken by several contractors for use in the design of operational and emergency mine communications. Pertinent measurements and data of other selected investigators were also included in the evaluation. This assessment treated the measurements and instrumentation used, the data analysis and presentation methods, and the utility of the final results. This phase concluded with the identification of the most useful results and methods, the remaining data gaps, the contractor most qualified to fill these data gaps, and the definition (with PMSRC and this contractor - NBS, National Bureau of Standards) of a follow-on noise measurement program, instrumentation system, and data processing methods tailored to obtain the necessary but missing noise data. A partial bibliography of references related to electromagnetic and seismic noise and propagation in the frequency bands of interest was also compiled during this first phase. The body of this Part of the final report presents a summary of the findings of our EM noise assessment, together with detailed recommendations regarding the new noise measurements to be taken and the instrumentation and data processing methods to be used. This work was done during the latter part of 1971 and the early part of 1972. During subsequent phases of the contract ADL was asked to perform on-going evaluations of the continuing program of electromagnetic (EM) noise and propagation measurements made by Bureau contractors, and to utilize pertinent data from these measurements to make performance estimates for

Jan 1, 1974

By W. M. Weigel

"Sand is one of the commonest materials for industrial use, not only as a building material, but in many industrial processes. The general name applies to all grades, from the comparatively impure, unsorted product used in concrete, to especially sized products of extreme chemical purity. Various definitions have been proposed, all more or less open to objection, as they fail to cover special applications. One is: ""Sand - The fine granular material naturally or artificially produced by the disintegration or crushing of rock or slag"". This does not fit the definition of sand as understood by geologists, who consider sand only as a naturally formed product. Another is: ""Sand - The fine granular material naturally produced by the disintegration of rock"". This does not take the chemical com-position into account, and for practically all uses, except in concrete and plaster products, a material composed predominantly of silica or rather quarts is implied.Sand for special purposes usually requires different methods of preparation from those where the ordinary mixture of sizes as naturally occurring are suitable. One of the classes requiring the most uniformly sized grains is sand blast sand.Sand Blast SandThe use of the sand blast has increased rapidly during the past few years. It was formerly used almost entirely in the foundry to clean and remove inequalities from rough castings. This is still the most important application, but in addition, it is now employed for the removal of paint from old surfaces, carving and engraving on stone and marble, glass cutting, cleaning or renovating the rails of stone and brick buildings that have become discolored, preparing the surface of metals for the electrolytic bath, putting the final finish to metal surfaces, and has even been proposed as a means of channeling or cutting out blocks of stone in the quarry."

Jun 1, 1924

By F. Fraas, H. H. Storch

"In the second paper 4 of this series, data were presented concerning the decomposi¬tion of polyhalite by saturated salt solutions. It was found that uncalcined polyhalite upon leaching with boiling saturated sodium chloride solutions yielded a brine in which the (K2 Mg) /304 ratio was considerably higher than that obtained from the calcined material, and for this reason appeared more suitable for the production of potassium chloride. It was found, in fact, that the leach liquors from uncalcined polyhalite deposited a mixture of KC1 and NaC1 upon evaporation and subsequent cooling, whereas those from calcined polyhalite yielded mixtures which contained not only potassium and sodium chlorides but also large quantities of glaserite, K3Na (S04)2. Hence it was decided to study the evaporation of the uncalcined poly—halite leach liquor and postpone experiments on the calcined polyhalite liquors until such time as a process for further removal of sulphate was developed.A considerable body of equilibrium data is available in the literature on thesystem K+ Mg++ — Na+ Cl—S04 =,— H20 for temperatures up to 83º C. Owing, however, tothe lack of data other than that corresponding to the invariant points and the complete absence of data for temperatures of 100 to 115°C., and owing to the fact that supersaturation phenomena render unsafe the prediction of the behavior of such a system upon evaporation, it was considered essential to obtain the necessary data by actual evaporation and analysis of the brines thus obtained."

Feb 1, 1931

By Ludwig Schmidt

The disposal of the brines produced with crude petroleum and natural gas has long been a constant source of trouble to oil and gas operators as well as to farmers and stock-raisers in the vicinity of producing fields. The amount of oilfield brines Produced from wells on new properties may be almost negligible, but some older wells may produce several hundred barrels a day. A survey of almost 200 wells on 31 properties in the eastern part of Osage County, Okla., showed that during the month of November, 1928, the average production of water was 3.26 barrels per barrel of oil produced. The age of the wells included in this survey ranged from two to 28 years; the maximum amount of brine produced was 26 barrels of water to one barrel of oil and the lowest was one barrel of water to 27 barrels of oil. These figures apply to a small area. In other fields the production of water also varies widely; for example, in the Cushing4, Okla., field several yells were reported as having produced 100 barrels of water to every barrel of oil produced. Often the production of oil-field brines is decreased materially and the production of petroleum increased by the use of bottom hole Plugs and by a general repair and cementing of wells. The records5 of 22 wells cemented in the Gushing field showed that prior to the repair work, the average total dally production was 242.5 barrels of oil and 3,977.5 barrels of water. The total Production of

Jan 1, 1929

This publication summarizes, for potential contractors and other interested parties, the research, development, and demonstration contract projects programed by the Bureau of Mines for fiscal year 1980 (October 1, 1979 - September 30, 1980) under its Minerals Health and Safety Research program. The objective of these projects is to provide an ordered and sequenced series of advances toward the Bureau's overall goal of providing the system technology required to create a healthier and safer working environment for the Nation's mining and minerals processing workers.

Jan 1, 1980

By C. E. Brechtel

This project describes the design and testing of large face ventilation systems for oil shale mining. A design data base was generated by reviewing general industry practice, oil shale industry planning, and technical literature. Conceptual designs for seven different systems were developed and evaluated for suitability. A large, free-standing, jet fan and reversible fan with rigid duct were selected for fabrication and testing. The two systems were field tested in a dead-end heading 55 ft wide by 30 ft high and 320 ft long. System performance was optimized using measurements of air flow direction and air velocity. Total system performance was then measured using SF6 tracer gas released to simulate blast fumes, hot diesel exhaust, methane layering and methane from a blasted muckpile. Field testing indicated that both systems delivered similar performance. The jet fan offered some clear advantages because of its mobility, ease of oper-ation and lower power requirement. It also offered some functional advantages in ventilating for methane because of it high average velocity.

Jan 1, 1985

By Bill M. Stewart

To decrease the potential for fine coal waste slurry impoundment failures, the Bureau of Mines investigated a new disposal technique. The fine coal waste slurry is rapidly thickened (i.e., dewatered) and deposited on a slightly sloping surface. To accomplish rapid dewatering, a chemical flocculation system using polymers was developed to treat the fine coal waste slurry stream. The fine solids formed flocs, settled from suspension, and rapidly released excess water. During the last 5 days of the field test, slurry flowing at rates from 498 to 675 gal/min with a specific gravity range of 1.15 to 1.33 was successfully treated and dewatered. During this period, untreated slurry had an average moisture content of 227.4 pct (30.7 wt pct solids). The effectiveness of the dewatering system was determined by monitoring the moisture content of the deposited waste with respect to time. Sixty-five hours after ending the field test the average moisture content was 54.9 pct (64.5 wt pct solids); 68 days after the field test the average moisture content was 28.8 pct (78.0 wt pct solids).

Jan 1, 1986

By Fredrick L. Johnson

In 1984, at the request of the U.S. Forest Service, the U.5, Bureau of Mines began a study of the 94,370-acre Arc Dome study area (4-667) in order to appraise its mineral resources, The Bureau of Mines mapped and sampled mines, prospects, and mineralized sites in and near the area, The study area is located in the Toiyabe National Forest, about 54 mi north of Tonopah, Nye County, NV, It is estimated that over 500 claims have been staked in the study area since the mid-1800?s. In January 1986, there were 108 active mining claims completely inside and 59 on the boundary. Another 283 active claims were outside the study area but within 1 mi of the boundary, In addition to the large number of claims staked, exploration activity is also reflected by the almost 700 inactive workings that were found during field investigation.

Jan 1, 1989

By Noel N. Moebs

The coal wants at the Westland Mine in southwestern Pennsylvania consist chiefly of elongated, sandstone-filled channels with slickensided basal contacts. Tentatively identified as washouts, these channels are about 1,000 feet long and 300 feet wide, are erratic in occurrence and trend, and are difficult to delineate from the customary core drilling pattern. Roof conditions are hazardous adjacent to the washout contact, but roof stability is generally unaffected greater than 30 feet away.

Jan 1, 1981

By W. A. Stickney

The Bureau of Mines conducted beneficiation and smelting studies on siliceous offgrade manganese samples to indicate effective methods of manufacturing silicomanganese from materials that cannot be economically beneficiated to meet General Services Administration (GSA) specifications for stockpiling. Laboratory and pilot-plant flotation tests were conducted on 2 samples, 1 from the waste-tailings dump of the Domestic Manganese & Development Co , Butte, Mont., and the other from the Nettie mine in the Butte-Philipsburg area. Smelting tests were made on the combined concentrates from the pilot-plant flotation tests and on part of the tailings sample The flotation scheme found to be adequate in laboratory tests and later in the pilot-plant tests consisted of flotation by a fuel oil-tall oil emulsion in an acid circuit (pH )-1-.8 to 5.0). The oil-emulsion reagent flocculated the manganese minerals and selectively floated them from the siliceous gangue, In the pilot-plant flotation test on Butte-mill tailings 90.1 percent of the manganese was recovered in a concentrate that analyzed 32.6 percent Mn, 4.8 percent Fe and 28.1 percent Si02. In the test on Nettie mine ore 90.8 percent of the manganese was recovered in a concentrate that analyzed 36 6 percent Mn, 5.5 percent Fe, and 26-4 percent Si02.

Jan 1, 1956

By JOSEPH F. CULLEN, Dorsey A. Lyon

In connection with its investigation looking to the prevention of waste and the increase of safety and efficiency in the mineral indus- tries the Bureau of Mines has undertaken a study of the possible uses of the electric furnace in metallurgy. This bulletin presents a com- pilation of such data as seem to be useful for the information of persons who may be interested in the matter. In the application of electricity to metallurgy three kinds of processes are involved, namely, mechanical, thermal, and electrolytic. Under the mechanical application of electricity come those proc- esses of dressing and concentrating ores that are known as either electrostatic or electromagnetic processes. In electrothermic processes the current is used as a source of heat. The fundamental differences between the various types of electric furnace that are at present in commercial use relate to the manner in which the electric current is applied, as may be noted by reference to that part of this report in which the subject is discussed. In electrolytic processes the electric current is used for depositing metals from solutions. The process may be conducted in one of the following ways: (1) The material to be treated may be put into solu- tion and then electrolyzed, the material thus treated forming the electrolyte; (2) the material to be treated may form the anode or be placed in contact with the anode; or (3) the material to be treated may form the cathode or be placed in contact with the cathode. This report treats of electrothermic processes, with the possible exception of those for the reduction of aluminum from its ores. Moreover, of the processes used in the so-called electrochemical in- dustries only those for the reduction of an ore to metal, or to a com- pound of the metal that is of value in itself, or is an aid in metallurgical work, are here discussed.

Jan 1, 1914

By R. L. Thorne

The Snettisham Peninsula, 30 miles southeast of Juneau, Alaska, was studied by the Bureau of Hines to obtain basic information about the size, grade, and metallurgical characteristics of a large basic intrusive containing titaniferous magnetite. The investigation, which was part of a continuing program to determine the potential reserves of iron and titanium ores in Alaska, included transit and magnetometer surveys, followed by diamond core drilling and metallurgical testing. The magnetic attraction of a part of the Snettisharn Peninsula is noted on early navigational charts prepared by the Coast and Geodetic Survey. Reconnaissance examinations by the Geological Survey and a preliminary dip needle survey by the Territorial Department of Mines indicated the general nature of the basic intrusive, but little was known as to the grade and extent of the magnetite mineralization. The detailed survey by the Bureau of Mines proved an area of approximately 390 acres in which generally high magnetic anomalies with exceptionally high localized anomalies occur. Subsequent drilling across B representative section of the deposit yielded core samples, which assayed from 11 percent to over 45 percent total iron. A large sample of core composited to represent the drilled portion of the de-posit assayed 18.9 percent Fe, 2.6 percent Ti02, and 0.29 percent S, 0.32 percent P, and 0.05 percent v.

Jan 1, 1956

By M. C. Malamphy

A general description of the activities and results of bauxite investigation by the Bureau of Mines at its bauxite project in Saline and Pulaski Counties, Ark., has been given in Report of Investigations 4251. The tactual data obtained during the project are reported in a series of Reports of Investigations beginning with No. 4251, of which this is the twelfth. The data are accompanied by maps showing the location of holes drilled and the deposits developed. Each area upon which work was done is reported by half townships. Each bauxite deposit investigated was assigned a name and a number for ready reference and identification, and its location and name are shown on the appropriate halt-township map. The description of each half township is followed by a description of each deposit developed in that halt township. The 14 half-township maps and 77 detail maps of the bauxite deposits in this series of reports give the locations and numbers of all the holes drilled on the project except the deep holes drilled to test the geophysical anomalies. The locations of those holes show on figure 13 in volume 1. The descriptions of the deposits developed are followed by complete detailed logs of the drill holes. Many of the widely spaced exploratory holes did not discover bauxite of minable thickness and grade. The pertinent information obtained from the widely spaced exploratory drill holes has been summarized and tabulated, and a table for each half township is given with the discussion covering that area.

Jan 1, 1948

By K. A. Fowler, L. W. Higley

Steels with an alloying addition of depleted uranium were studied to develop successful melting , casting , and fabricating methods ; to obtain data on mechanical properties ; and to determine the effects of this alloying element . Uranium in amounts up to 1.5 percent was added to steel - base compositions containing approximately 0.5 percent carbon , 2 percent nickel , 0.25 to 2.0 percent silicon , and 0.75 percent manganese in both vacuum- melted and air -melted heats . Radiation levels were monitored for all operations . Bureau of Mines research at the Rolla Metallurgy Research Center showed that uranium additions did not increase tensile strength ; that hot - shortness occurred during forging above 1,090 ° C because of the presence of a low melting point constituent of a eutectic type ; and although a measurable amount of radioactive contamination resulted from processing , the quantity was never large enough to require the work area to be identified as a radiation area .

Jan 1, 1964