Search Documents

By A. Wahab Khair, Richard D. Begley

"This paper presents results of destructive tests performed on rectangular coal specimen under the influence of two vertical and simultaneous wedge indentation forces. Several wedge designs and spacings were utilized in compression tests. The objective of these experiments was to qualitatively monitor the effect of different wedge designs and spacings on the stress distribution within the coal specimen.Coal samples from the Waynesburg coal seam were cut and trimmed to cubical dimensions of approximately 5 X 10 X 20 cm. These specimen were subjected to parallel compressive forces through two vertically applied wedge indentors. Loading was achieved with a hydraulic hand pump in order to facilitate interferogram construction. The load increments were limited due to the sensitivity of the holographic interferometric technique (holometry) in measuring small displacements; therefore, interferograms were taken only during similar increments in order to allow for a qualitative comparison between different wedge design and spacings. In some cases, interferograms were taken immediately before and after failure of the specimen.Introduction Failure Modes Three distinct modes of failure occur when geologic materials are subjected to wedge indentation forces. As shown in Figure 1, a crushed zone is located immediately adjacent to the indentor while chipping can occur if the fractures initiated in the crushed zone extend upwards to the free surface.. The third failure mode is a zone of intricate frac¬tures located between the crushed zone and the chipping zone. Several experiments have been conducted over the years to better understand crater formation and stress distribution within geologic materials under the influence of an indentor. Generally speaking, crack initiation and propogation observed in these experi¬ments correlate fairly well with wedge indentation theory; however, the nature of the .fractures is greatly influenced by different material properties such as grain size and cleavage planes. In other words, a wide range of behavior has been found in different rocks subjected to wedge penetration. For example, it has been observed that some rocks are merely crushed and indented while others are more prone to cracking and chip formation. Therefore, the development or nondevelopment of chips depends mostly on wedge geometry, rock type and depth of penetration. This work is part of the study associated with opti¬mization of cutting parameters, which is best modeled by using brittle materials and subjecting them to rigid wedge penetration tests."

Jun 1, 1988

By J. G. Kirby

According to the Bureau of Mines annual survey, as of January 1, 1954 there were 337 refineries with a total daily crude-oil throughput capacity of 8,006,897 barrels. The total daily capacity increased 368,236 barrels during the year while the total number of refineries declined 6. The capacity of the average refinery to process crude oil therefore increased during 1953 from 22,270 barrels to 23,759. With the exception of the Texas Inland, all refining districts reported gains in the installed capacity for the year, the largest being the Louisiana Gulf Coast with an increase of 20 percent. A total of 397,500 barrels of additional crude oil capacity was reported as under construction January 1, 1954. Accounting for 129,500 barrels of this total are facilities for 3 new refineries in North Dakota, 2 in Washington and I each in Ohio and Utah. Equipment being installed to replace existing units, totaled 180,750 barrels daily.

Jan 1, 1954

By R. E. Cerullo

Many computer programs have been written which are capable of performing a least squares fit, both linear and nonlinear, to data gathered by the petroleum researcher. However, when the petroleum engineer tries to program methods of analysis he has used manually in the past, such as forecasting production by decline-curve analysis, more than a knowledge of the use of existing least squares programs becomes necessary. It is the intent of the authors to report the techniques used in the development of such a decline-curve program.

Jan 1, 1970

By Binyon E. O.

The tungsten properties of Lincoln Mines, Inc., and North Tem Piute Mining and Development Co. were first explored by the Bureau of Mines in 1942. Work on the project comprised trenching, sampling, a small amount of road and trail construction, and a small amount of core drilling. From April 13 to December 10, 1944, additional diamond drilling was done by the Bureau of Mines to test the lateral and downward extensions of the various tactite zones along the contact south of the Lincoln mine, including the property of the North Tem Piute Mining & Development Co. Claims leased by the Lincoln Mites, Inc., are in secs. 25 and 36, T. 3 S., R. 56 E.; secs. 30 and 31, T. 3 S., R. 57' E.; and sec. 1, T. 4 S., 56 E., M. D. B. & M., in the Tem Piute Mining District, near the north end of the Timpahute Range in west central Lincoln County, Nev. D. B. Fegles is president of Lincoln Mines, Inc., and general offices are in the Wesley Temple Building, Minneapolis, Minn.

Jan 1, 1950

By E. J. Gleim

To make a thorough survey of a coal mine in order to eliminate hazards, the competent safety engineer must be familiar with mere than one branch of engineering. It is essential that he know the properties of mine gases and the methods of detecting them, as well as hew to prevent dangerous as accumulations. It is also essential that he understand the action of overlying strata when the coal is removed, and the proper methods of protection by timbering or other suitable means of support. He must know the value of protective clothing in reducing injuries and mast be informed as to the correct handling and use of explosives to avoid premature blasts, misfires, and ether failures in blasting practice. He must understand hew to operate locomotives and cutting, loading, and various other types of machines to be able to recommend effective safeguards for protecting the men who use them in addition to being informed as 'to these and many ether activities connected with the mining of coal, he must net overlook electrical engineering if he wishes to combat the fire, shook, and ignition hazards attendant upon the use of electrical machinery and circuits in and around the mine intelligently. There are many points relating to safely in the selection, maintenance, and use of electrical circuits and equipment that are perfectly obvious to the electrical engineer but perhaps are not se evident to those not trained in this particular branch of engineering. Engineers of the U.S. Bureau of Mines who have made a special laboratory study of electricity as related to safety in minus haw e also made inspections of electrical installations at a large number of bituminous mines. These inspections have revealed practices and conditions that not only do not contribute to safety but that add nothing to efficiency and economy in the operation of the mine.

Jan 1, 1936

By P. W. Jeran, C. M. McCulloch, Maurice Deul

The natural vertical fracture sys tem in bituminous coalbeds is called cleat. Cleat orientation commonly controls the direction of mining with major development paralleling the face cleat. Previous researchers have categorized the origin of cleat as endogenetic, relating the origin of cleat to compaction and coalification, and exogenetic, relating the origin of cleat to tectonic forces. In the coalbeds studied for this report it was found that tectonic forces were the controlling factor of cleat formation. Face cleats were formed as extension fractures during structural deformation, and butt cleats, as release fractures during erosion and uplift. The face cleat of the Pittsburgh coalbed rotates from N 80° W in north- western West Virginia to N 57° W in southwestern Pennsylvania ; the face cleat maintains a perpendicular orientation to the shifting axial trend of local structures . Cleat orientation in other bituminous coalbeds in Virginia, Utah, Oklahoma, and Central Pennsylvania showed a similar relationship to local structure. Directional permeability of coal is directly related to cleat. Holes drilled perpendicular to the face cleat yield from 2.5 to 10 times the amount of gas released as compared with holes drilled perpendicular to the butt cleat.

Jan 1, 1974

By Bernard Porter

The rate of the heterogeneous reaction between reactor-grade yttrium and lithium fluoride in lithium fluoride-yttrium fluoride mixtures was measured using a quartz spring balance. At 950° C the magnitude of the rate of reaction is 10-5 grams of yttrium/cm2-sec. The heat of activation for the reaction is 38.3 kilocalories per mole of LiF. A surface-controlled mechanism is proposed in which LiF is adsorbed on the yttrium metal surface. An activated complex is formed when additional LiF reacts with the adsorbed LiF-metal site. The activated complex then decomposes to the products) which are lithium metal and YF3. The importance of the reaction in the electrowinning of yttrium metal from fluoride electrolytes is discussed.

Jan 1, 1967

By John W. Buch

At a meeting of the Anthracite Investigations Advisory Committee in July 1944 at Washington, D. C., the initial work and objectives of the Anthracite Mechanical Mining Section of the Federal Bureau of Mines were discussed. It was learned that interest existed in an improved performance of mining thin, steeply pitching beds above the gangway by mechanical methods. One company offered the use of one of its mines for experimental work, and this offer was accepted. Following acceptance, an effort was made by Bureau engineers to devise a mechanical method with a performance better than that of a new hand method proposed by company engineers for an actual mining condition. The method proposed by the Bureau was to drive 30-degree slant chutes across a 10-foot bed pitching 85 degrees. These chutes were to be advanced by using a lightweight, compressed air-powered, shearing machine of German origin that had been tried in a flat Pennsylvania anthracite bed in 1934, and which did not then prove successful because of blasting difficulties. An attempt was made to obtain one of these machines from England, where it was known machines of this type had been used. Shortly thereafter John W. Buch was sent to Europe as a member of the Solid Fuels Mission to the European Theater of Operations organized by the Technical Industrial Intelligence Committee of the Joint Chiefs of Staff. Through his efforts the Bureau of Mines obtained two such machines, known as the Eickhoff model DEK, one from England and one from Germany. This report covers the preliminary testing of these machines in order to obtain mechanical operating data for use in determining the power requirements for cutting anthracite with machines of this design.

Jan 1, 1949

"One of the functions of the United States Bureau of Mines is to investigate the ability of electrical mining equipment to operate in a gassy mine without danger of igniting explosive atmospheres. To accomplish this purpose, tests are made in which mixtures of gas and air are ignited in the equipment while it is surrounded by explosive atmospheres of the same composition. In such tests, records of pressures developed by the internal ex-plosions are obtained and observations are made of any flames, sparks, or smoke which may issue from bearings and joints. Occasionally the explosion pressures in a mining machine rheostat or a compartment of some other machine reach a value which is judged to be excessive or abnormal.A number of factors are known to influence the explosion pressures, and both German and. British investigators have irate extensive research on their effects. Much of this work had been done with artificial compartment which certain conditions could c held, constant while others were being varied. The U. S. Bureau of Mines has not made any research on a scale to compare with that of the British or German investigators; however, special studies have been necessary from time to time to determine the cause and remedy for high pressures obtained in the routine test of some piece of mining machinery. Thus it has been possible to verify some of tee theories established on a purely experimental oasis by practical tests of machines as actually built for mine use.Some of the factors determined the pressure that will result when an explosive mixture in a compartment or connected compartment is ignited are: (1) The volume of explosive mixture ignited, (2) the percentage of as in the mixture, (3) the amount of coal-dust in the compartment or compartments, (4) the degree of movement or turbulence of the mixture at the time of ignition, (6) tightness of the joints and bearings, (6) the size of opening between, compartments, (7) the distance between the point of ignition and openings, and (8) the cooling, effect of surfaces and of material inclosed in the compartments."

Dec 1, 1929

By A. G. Starliper

Laboratory studies were made to produce whiskers of tungsten over a wide range of operating temperatures. Hydrogen reduction of tungsten hexachloride in a vacuum furnace at temperatures from 2,7000 to 3,3000 C yielded a small quantity of tungsten whiskers, provided a low degree of supersaturation was maintained. Direct measurements of 3,000,000 to 4,000,000 psi were obtained for the ultimate tensile strengths of individual whiskers averaging 3 to 4 microns in diameter with average aspect ratios of 1,000. This compares with strengths of 300,000 to 400,000 psi for 13-micron-diameter commercial filaments.

Jan 1, 1968

By Edward D. Thimons

Inflatable stoppings are currently marketed for production use, and numerous mining companies have become interested in using such stoppings in rescue and recovery operations. The Bureau of Mines therefore evaluated the concept of using inflatable stoppings in emergency situations. The stoppings tested by the Bureau were 12-foot-diameter spheres inflated with a blower operated by a small battery pack. Experiments were conducted with the stoppings in a full-scale wooden mine model to evaluate their ability to withstand sliding or slipping at various internal and differential pressures, puncture resistance, various inflation techniques; and internal leakage from the stoppings. The stoppings were then installed and tested in the Bureau's Safety Research Coal Mine at Bruceton, Pa., to determine their effectiveness as mine air barriers. Despite some encouraging results obtained with the model and in-mine studies, the stoppings did not perform well in two operating metal mines where they proved difficult to erect and inadequate as air barriers.

Jan 1, 1976

By H. Stuart Auvil

Twelve samples of run-of-oven coke were taken at coke plants in the United States and Canada. Sampling procedure was directed toward obtaining the highest possible degree of uniformity in the gross samples, so that variations in results caused by sampling variations were at a practical minimum. Under these conditions the standard deviation of the screen analysis test on 500-pound samples is found to range from 1.2 percent for the 1-inch screen to 4.5 percent for the 5-inch screen. At present, the A.S.T.H. standard method of test requires that results be reported to the nearest 0.1 percent. This implies a higher than actual degree of precision, and revision of the report required by the method is suggested. Much larger Samples than are generally tested are required to reduce normal testing errors to a point where they are not appreciable fractions of the total variations found in a smoothly operating plant. For example, it is deduced that over 100,000 pounds of coke must be screened to determine if ordinary day-to-day variations in screen analysis have appreciable effects on the performance of a blast furnace.

Jan 1, 1950

By Emory Smith

The Victorville cement plant of the Southwestern Portland Cement Co. is located about 1 mile from the city of Victorville, Calif. Two transcontinental railway systems, the Atchison, Topeka & Santa Fe, and the Southern Pacific Railroad, afford shipped facilities. The plant is modern and well kept, as the officials, especially the higher operating officials, take pride in the appearance of the place. Dust has been practically eliminated by the installation of dust collectors and wet grinding. The plant has a rated capacity of 5,000 barrels of cement daily.

Jan 1, 1929

By H. William Zeller

The Bureau of Mines performed laboratory research into the effects of a barium-based fuel additive (the "postflame" type) on diesel particulate matter (DPM) emissions. The 5.6-L, six-cylinder test engine is typical of types certifiable for use in underground mines. Test parameters consisted of additive concentration and engine loads, speed, and air intake restriction. DPM emissions, including condensed volatiles, were measured gravimetrically. Also measured were gaseous emissions including carbon monoxide, nitrogen oxides, and hydrocarbons. The fuel additive was effective, reducing DPM up to 75 pct, when used at a concentration of 0.09 wt pct (one-fourth of the concentration recommended by the manufacturer). The additive was most effective at the highest fuel-air ratios, reducing DPM from 400 mg/m3 for untreated fuel to 120 mg/m3. At light loads, 25 pct of full rated, no DPM reductions were measured. Based on these results, the additive is recommended for use in diesel fuel, at a concentration of 0.09 wt pct, to power underground mining equipment as long as certain conditions are met: that a beneficial DPM reduction is verified, that the minimum required quantity of additive is used, and that potential adverse effects such as increased nitrogen oxides are checked.

Jan 1, 1990

By L. B. Berger

This information circular is a revision of I.C. 7238, Danger from Carbon Monoxide in the Home, by L. B. Berger and H. H. Schrenk, issued in April 1943. Each winter brings its toll of deaths and serious accidents from the deadly gas, carbon monoxide. Newspapers carry warnings to the public of the, dangers of this gas, and frequent news items report the finding of persons dead at unconscious from the effects of carbon monoxide, yet these accidents continue. Either these warnings are not read, or they are unheeded by people who feel that, "It can't happen to me." It can happen to you carbon monoxide is no respecter of persons.

Jan 1, 1954

By W. A. Stickney

As part of a Bureau of Mines program to investigate recovery of manganese (Mn) from low-grade materials, laboratory studies were made of four samples of mill rejects: Three from Montana and one from Peru. These studies demonstrated that certain mill-waste products can be a potential source of manganese. Both manganese oxide and carbonate minerals were recovered by flotation in an acid circuit with a fuel oil-tall oil emulsion as collector. Sintering) required to prepare a physically acceptable product, also was used as a method of beneficiation. In addition to being low-grade, some of the samples presented problems of intimate mineral association and complex textures.

Jan 1, 1960

By Paul W. Johnson, Ralph C. Kirby, Frank A. Peters

An evaluation is presented for a process designed , on the basis of published work , to extract alumina as potassium alum from clay using sulfuric acid and potassium sulfate . The silica residue is separated by filtration . Ferric iron is reduced to ferrous iron , and the alum is crystallized from the solution , leaving the ferrous iron in solution . The alum crystals are separated from the solution and redissolved for feed to autoclave decomposition . In an autoclave the alum is partly decomposed to a basic alum , recovering five - ninths of the sulfuric acid and two - thirds of the potassium sulfate without using an acid plant . The basic alum is decomposed by calcining , and the potassium sulfate is then removed by washing with water . Operating costs for a plant producing 1,000 tons of alumina a day are estimated at $ 96.15 per ton of alumina . The fixed capital cost is estimated at $ 155 million . This process is not competitive under current economic conditions with the production of alumina from bauxite by the Bayer process . Improvement in leaching , basic alum decomposition , and washing could reduce the costs and improve the product which contains some potassium .

Jan 1, 1963

By P. G. Clites

A laboratory furnace was developed by the Federal Bureau of Mines for use in studying the interrelationships among variables associated with skull melting and casting high-temperature metals. Although additional work is necessary to determine the extent to which the information obtained by using this furnace can be extrapolated to larger furnaces of the same type, many casting characteristics of metals and alloys can be determined on equipment of this size. This furnace is a laboratory-size, consumable-electrode, skull-casting furnace equipped with a water-cooled copper ladle. The ladle, which is a tilt-pour or over-the-lip type, has a volume of approximately 30 cubic inches and provides up to 20 cubic inches of molten metal for castings. Castings of various reactive and refractory metals, including zirconium, titanium, hafnium, columbium, molybdenum, tantalum, and tungsten, have been produced. In addition, castings of iron, chromium, and copper have been made. The simplicity and versatility of the apparatus would make it useful to metallurgical laboratories preparing cast specimens.

Jan 1, 1961

By Richard F. Hewlett

An attempt has been made to fit assay data from an underground copper deposit to a three-dimensional polynomial surface as a means of expressing assay points in terms of their mine coordinates by a mathematical equation. The resulting equation was evaluated to predict the grade trend of the deposit. Although the fit obtained by this initial experiment is not considered accurate enough to provide good predictions about the deposit, the methodology is presented in this preliminary report to show the potential usefulness of the technique in mineral deposit evaluation. The technique also should be useful in determining the grade of blocks of ore for production scheduling and blending problems in open pit operations. Further experimentation is needed to increase the reliability of the computer program, to increase the precision of the method, and to make the solution more flexible for use on other mineral deposits.

Jan 1, 1964

By N. S. Dalal, X. N. Hu, X. Shi, V. Vallyathan

"Although silicosis has been studied extensively, the mechanism is still not fully understood. Experiments do provide evidence that the actions of unique properties of silica surface on the cell membrane are the starting point of silicotic processes. This paper summarizes literature on chemical properties of silica surface, and the effect of particle size on silica toxicity. This paper also discusses the ways in which silica dusts are thought to interact with the cell membrane, with emphasis on freshness, hydrogen bonding, and free-radical interactions.INTRODUCTIONSilicosis is a debilitating pulmonary disease that afflicts persons (miners, foundry workers, ceramic workers, heavy construction workers, etc.) who chronically inhale silica-containing dusts (Schepers, 1960; Silicosis and Silicate Disease Committee, 1988). Since silica is second only to oxygen in weight percentage of the earth's crust (about 28%) and is found in an enormous diversity of minerals, it is natural that silicosis is one of the major industrial health hazards all over the world. Although silicosis has. been studied extensively, the mechanism by which the dusts exert their toxic actions on cells and the processes by which these actions progress to fibrogenesis are still poorly understood. The biological characteristics of the dusts are largely unknown, although it is suggested that the dust size, shape, surface charge, roughness, surface chemical composition, trace metal content, and crystallinity; dose of silica in the ambient air of the workplace; duration of exposure; genetic variation in exposed subjects; personal respiratory patterns; and presence of any coexisting disease (such as tuberculosis or rheumatoid arthritis) all influence the expression of silicosis (Koskinen et al., 1983; Noweir et al., 1980; Raask and Schilling, 1980; Reiser and Last, 1979; Thorne et al., 1985; Wolff et al., 1981). The actual biochemical mechanisms through which these factors operate are still unclear. However, the experiments do provide evidence that the actions of certain unique properties of silica surface on the cell membrane are the starting point of the silicotic process (Allison et al., 1966; Allison and Harrow, 1971; Bateman et al., 1982; Marks, 1957; Parazzi et al., 1968; Reiser and Last, 1979; Summerton et al., 1977). This article summarizes literature on chemical properties of silica dusts and how silica dusts are thought to interact with the cell membrane, with emphasis on hydrogen bonding and free-radical interactions."

Jan 1, 1989