Search Documents

By S. H. Ash

THE ANTHRACITE region of Pennsylvania contains over nine-tenths of the total anthracite deposits of North America and produces all but an insignificant proportion of the total output of anthracite in the Nation. The whole economy of the northeastern section of the United States depends, to a large extent, on the mining of Pennsylvania anthracite, which is shipped to New Jersey, New York, and New England and is a principal source of energy and heat for that entire region. The responsibility of the Federal Government for developing an engineering method that will prevent inundation of the Pennsylvania anthracite mines and keep them in operation has long been recognized. To obtain a reliable picture of the anthracite-mine-water problem and to solve that problem, it is necessary to have factual data on the volume and the quality and character of the mine water handled by the pumping plants in the anthracite region, as well as the kinds of pumps utilized and problems concerning their operation.

Jan 1, 1953

By J. Burlin Johnson

In small-scale blasting experiments conducted in the Bureau of Mines laboratory, small charges were used to produce craters in blocks of concrete mortar. The results are compared with larger scale experiments of other research workers, and the comparison demonstrates the similarity of the results obtained and indicates that small-scale blasting should be a useful tool for predicting large-scale blasting effects. INTRODUCTION The purpose at this investigation was to conduct blasting experiments in mortar in the laboratory and then, by comparing the results with those from larger scale field blasts in rock to determine to what extent, if any, the laboratory results resemble those in the field. The work described herein was the initial phase of a project aimed at evaluating small-scale blasting as a tool for use in improving blasting techniques. It is evident from the stand-point of control and cost that small-scale blasting would be valuable in the study of rock fragmentation by blasting in mines and quarries, if the extrapolation is valid.

Jan 1, 1962

By G. L. Bloomsburg

This report describes work which was done to apply an existing finite element computer program UNSAT2 to the unsteady, unsaturated flow of water through waste shale piles. The work was done in three phases: 1. Verification of program through comparison with existing data. 2. Verification of program through simulation of flow from field seepage ponds at Rifle, Colorado. Considerable laboratory work was done in this phase to obtain capillary pressure-saturation-relative permeability data and hydraulic conductivity values for retorted shale. 3. Application of program to flow due to natural rainfall in a section through the Piceance Basin in Colorado, and a typical waste shale pile.

Jan 1, 1978

By Alan G. Mayton

The Bureau of Mines conducted one of the most extensive studies on surface mine illumination to date, to assess the illumination needs of mobile surface mining machinery with respect to the visual tasks required of machinery operators. Field Investigations were performed at 22 surface mining operations, coal and metal-nonmetal, within several mining regions of the United States. Visibility and illumination were measured for 159 visual tasks performed by equipment operators on or near 57 surface mining machines, including draglines, shovels, blasthole drills, bulldozers, loaders, haul trucks, graders, scrapers, and several service-type vehicles.

Jan 1, 1987

By Thomas L. Chapman

The San Manuel is a deposit of low-grade disseminated copper ore. It was brought to the attention of the government in October 1942 through an application to the Reconstruction Finance Corporation for a development loan, supported by a report by Henry W. Nichols. Nichols' sampling of two outcrops containing copper silicate and his geologic map indicated that a minable body of copper ore might be developed. The Federal Geological Survey was requested to examine the property. The Survey mapped the geology in March 1943 and cut a few check samples, which substantially confirmed Nichols' sampling of the outcrops and a few shallow workings. The geologists of the Survey recommended some test drilling by the Bureau of Mines. The property was examined by the author and Wm. D. Hughes, associate engineer of the Bureau of Mines on March 22 and 26, 1943, and a preliminary drilling campaign was recommended. Five shallow churn-drill holes totaling 1,480 feet were put down under the supervision of Chas. A. Kumke, one of the Bureau's engineers, from November 23, 1943, to January 13, 1944. This work indicated that the deposit extended deeper than the 350-foot depth attained in the deepest hole and might have very considerable areal extent. Additional funds were allotted, and the drilling contract was extended twice to a final maximum of 17,000 feet with 2,000 feet maximum depth of hole. Drilling was continued by the Bureau of Mines until February 2, 1945, when 15,844 feet of hole had been drilled. The Magna Copper Co. took options on this and adjoining property in September 1944 and commenced drilling with two machines. It also engaged the two contract drills used by the Bureau after it stopped drilling. It exercised its options in August 1945 and organized the San Manuel Copper Corp. to operate the property. That company is continuing to explore the ore body with six churn drills. Thomas Lyon took options early in 1945 on holdings adjoining the San Manuel property on the east and is operating two churn drills. Exploration up to the completion of the last holes started by the Bureau of Mines indicated a block of ore 3,100 feet long, 400 to 800 feet wide, and 500 to 900 feet thick, and averaging about 0.8 percent copper. Subsequent drilling showed that the ore body extends considerably beyond this block. The axis of the ore body strikes about N. 61° E. Copper minerals are disseminated in hydrothermally altered quartz monzonite and monzonite porphyry. Ore outcrops in two small areas over the northeast part of the block. Elsewhere the copper-bearing rocks are capped by Gila conglomerate, which thickens toward the west and south. Drilling showed that the ore is in a thick, tabular body with a steep dip to the south. The ore body lies near the surface in the northeastern part of the block. The south side of the block is much farther below the surface than the north side. There the upper part of the copper-bearing rocks is lightly mineralized, so that the hanging wall of minable ore lies deeper than the base of the conglomerate cap, which thickens southward.

Aug 1, 1947

By Thoms L. Chapman

The San Manuel is a deposit of low-grade disseminated copper ore. It was brought to the attention of the government in October 1942 through an application to the Reconstruction Finance Corporation for a development loan, supported by a report by Henry W. Nichols. Nichols’ sampling of two outcrops containing copper silicate and his geologic map indicated that a minable body of copper ore might be developed. The Federal Geological Survey was requested to examine the property. The Survey mapped the geology in March 1943 and cut a few check samples, which substantially confirmed Nichols’ sampling of the outcrops and a few shallow workings. The geologists of the Survey recommended some test drilling by the Bureau of Mines. The property was examined by the author and W. D. Hughes, associate engineer of the Bureau of Mines on March 22 and 26, 1943, and a preliminary drilling campaign was recommended. Five shallow churn-drill holes totaling 1,480 feet were put down under the supervision of Chas. A. Kumke, one of the Bureau’s engineers, from November 23, 1943 to January 15, 1944. This work indicated that the deposit extended deeper than the 350-foot depth attained in the deepest hole and might have very considerable areal extent. Additional funds were allotted, and the drilling contract was extended twice to a final maximum of 17,000 feet with 2,000 foot maximum depth of hole. Drilling was continued by the Bureau of Mines until February 2, 1945, when 15,844 feet of hole had been drilled. The Magma Copper Co. took options on this and adjoining property in September 1944 and commenced drilling with two machines. It also engaged the two contract drills used by the Bureau after it stopped drilling. It exercised its options in August 1945 and organized the San Manuel Copper Corp. to operate the property. That company is continuing to explore the ore body with six churn drills. Thomas Lyon took options early in 1945 on holdings adjoining the San Manuel property on the east and is operating two churn drills. Exploration up to the completion of the last holes started by the Bureau of Mines indicated a block of ore 5,100 feet long, 400 to 800 feet wide, and 500 to 900 feet thick, and averaging about 0.8 percent copper. Subsequent drilling showed that the ore body extends considerably beyond this block. The axis of the ore body strikes about N. 61º E. Copper minerals are disseminated in hydrothermally altered quartz monzonite and monzonite porphyry. Ore outcrops in two small areas over the northeast part of the block. Elsewhere the copper-bearing rocks are capped by Gila conglomerate, which thickens toward the west and south. Drilling showed that the ore is in a thick, tabular body with a steep dip to the south. The ore body lies near the surface in the northeastern part of the block. The south side of the block is much farther below the surface than the north side. There the upper part of the copper-bearing rocks is lightly mineralized, so that the hanging wall of minable ore lies deeper than the base of the conglomerate cap, which thickens southward.

Aug 1, 1947

By Robert R. Stein

Occupational noise caused by the rock drills used in mining was investigated by the U.S. Bureau of Mines. Using a large reverberation chamber and an automated drill test fixture (ADTF), the sound power levels of mining drills were measured to determine if there are types of drills that are advantageous from a noise production standpoint. Test results show that while there are not large variations among types of drills, there are still some choices that could produce a positive effect on overall noise exposure. It is also shown that lower noise exposures are possible using larger drills because of higher production rates and better operator positioning.

Jan 1, 2010

By S. J. Aresco

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash-softening temperature, the free-swelling index, and the Hardgrove grindability index. Under most of these specification contracts the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions4 issued by the Bureau of Mines; the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor; if it is not, a price adjustment is made. Analyses of the delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous sampling of coal as delivered is a check on the practical results obtained in burning the coal.

Jan 1, 1966

By P. G. Clites

This bulletin summarizes the results of Bureau of Mines research on the development of the inductoslag melting process. Inductoslag melting is an induction melting technique using a segmented, water-cooled, copper crucible. The process was developed as part of the Bureau's work on effective utilization of reactive metal scrap, and the process has been applied to melting Ti, Zr, Cr, Co, Fe, Ni, and V. Construction details are given for the segmented crucibles and for both an ingot furnace and a casting furnace. The melting process is described, and results of tests conducted with a variety of reactive metals are given.

Jan 1, 1982

By D. S. Kimmel

The Bureau of Mines sponsored development of a system to remotely energize and de-energize the trolley wire in a section in response to demands from vehicles as they enter and leave the controlled section. The system developed utilizes a detector/actuator that controls a dc contactor at the outby end, and a 3 kHz oscillator at the inby end. A prototype system has been built and installed at the Bureau's trolley test site at Bruceton, Pennsylvania which has demonstrated the ability to also provide load discrimination for faults of 300 amperes or more. The system could readily be modified by locating the oscillator on the vehicle to provide automatic de-energizing of the trolley wire when the vehicle's pole is removed or the vehicle leaves the section.

Jan 1, 1978

By Gary R. Gavan

This report presents the results of a research project that gathered detailed information on the composition of the population of mobile equipment used in U.S. coal mines. A computerized data bank containing over 19,000 pieces of coal mine equipment in use in 1976 was prepared with a data retrieval program. Operator protective structure technology is reviewed; field problems experienced with ROPS are discussed.

Jan 1, 1978

By John P. Harmon

Vehicles traveling on untreated dirt and gravel roads at open-pit mines disseminate high concentrations of dust (fig. 1). Excessive dust creates safety hazards by reducing visibility and may endanger the health of the men who breathe it. If the dust contains free silica, it can cause silicosis. In addition, maintenance costs of mechanical equipment are increased if equipment is operated in extremely dusty places. Dust on haulage roads in hot, arid country can be controlled if the surface of the road is sprinkled frequently and adequately with water. Often, when roads are sprinkled with water to control the dust, hazards are caused through reduced traction and skidding because of the mud that is formed on the surface of the road. Reducing the amount of water used will help to reduce the hazard of skidding.

Jan 1, 1957

By R. R. Wells

An important activity of the Bureau of Mines is the continual search for new sources of minerals. As a part of the investigation of strategic mineral deposits in the United States, samples of mercury ores were submitted to the Ore Dressing sections of the Salt Lake City and Albany stations for metallurgical testing. This paper gives data summarizing the results obtained from laboratory beneficiation studies of mercury ore samples submitted during the period 1941 to 1947. Ores tested included three from Jackson County, Oreg., one from Valley County, Idaho, one from Storey County, Nev., and one from Sonoma County, Calif. In general, the ores from Oregon were not amenable to concentration by flotation because of intimate association of cinnabar with other minerals or because of extremely low grade. One Oregon ore was amenable to direct distillation provided lime was added to reduce corrosion of the retort.

Jan 1, 1950

By S. J. Aresco

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash-softening temperature, the free-swelling index, and the Hardgrove grindability index. Under most of these specification contracts the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions3 issued by the Bureau of Mines; the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor; if it is not, a price adjustment is made. Analyses of the delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous sampling of coal as delivered is a check on the practical results obtained in burning the coal.

Jan 1, 1968

By Richard O. Kneisley

An empirical method, based on U. S. Bureau of Mines field studies in several Western U.S. coal mines, is presented for sizing gate road yield pillars. Discriminant analysis was used to generate functions separating successful from unsuccessful case studies. These functions relate the pillar width-height and extraction ratios and a pillar development factor to the Coal Mine Roof Rating System (CMRR), and are assumed to establish three criteria that other entry systems, under similar conditions, must satisfy. A program, Pillar Sizer, from user-provided inputs, generates a range of pillar sizes that meets the proposed criteria. Although the analysis is based on a sample consisting primarily of two-entry systems, the derived expressions generate pillar sizes closely agreeing with observed, two-entry and three-entry in situ pillars. It is concluded that the proposed approach should assist mine operators estimate entry system yield pillar dimensions.

Jan 1, 2010

By J. A. Baicker

A prototype borehole probe for ore grade determinations by means of in-situ neutron activation analysis was designed, built, and tested in a two-phase program. Phase I dealt with the design and fabrication of a borehole logging system for operation in 7.6 cm (3 in.) diameter or larger boreholes. It consisted of a 5.06 cm (2 in.) diameter borehole probe containing an intrinsic germanium detector, a canister-type solid cryogen cooling system, cooled FET preamplifier, linear amplifier, high voltage supply, analog-to-digital converter, microprocessor-based multichannel analyzer, buffer memory, bi-directional cable link, power supplies, and a Californium-252 neutron source. A surface support vehicle was designed and outfitted. A minicomputer system was constructed and software developed and tested. In Phase II the system was field tested at several mine sites. The system was calibrated, tested, improved, and demonstrated in a variety of applications. Tests were performed at sites pertinent to uranium, iron, coal, copper, silver and gold. Technical feasibility was demonstrated for all these applications except gold; the gold results were inconclusive. In-situ neutron activation analysis using high resolution gamma ray spectrometry was found to be a potentially viable logging method for are grade analysis under certain conditions.

Jan 1, 1984

By C. Watson Owings

"The mining Industry in the United States is becoming fully cognizant of the hazards of dust in underground mining as well as in surface plants. The dust problem in metal mines has been brought to focus through knowledge of the harmful effects of dust, especially silica, and through adoption of more or less stringent legislation classifying certain types of pneumoconiosis as occupational diseases. The coal-mining industry is aroused principally by the apparently great increase in the dust-explosion hazard resulting from the rapid growth of mechanized mining. The United States Department of the Interior, through the Safety. Division of the Bureau of Mines, has been requested repeatedly to recommend methods of allaying dust in both coal and metal mines. Methods adequate under hand-mining conditions fail to effect satisfactory reduction of dust in more rapid extraction with modern equipment. Studies of methods and equipment for allaying dust are being conducted in both metal and coal mines. Results of these studies are discussed, and indications of possible means of reducing dust concentrations are presented in the hope that the health and 'safety of men employed in the mining industry may be increasingly safeguarded.DUSTThe term ""dust"" is a common one, and yet the meaning is applied to widely different particle sizes. The general term means ""earth or other matter reduced to fine, dry, and powdery particles."" The root from which the word is derived means ""something that can be blown about by the wind."" As a result of tests on the explosibility of coal, the Federal Bureau of Mines has arbitrarily defined dust as being. ""that which will pass through a 20-mesh screen,"" based upon the fact that particles coarser than 20-mesh have little influence on the development of an explosion of Pittsburgh coal-bed dust. The study of dust, from a health standpoint, has given rise to still another definition of dust, namely,- according to Drinker3/, ""solid particles ranging in size from less than 1 micron to about 150 microns."" A micron is 1/25,400 inch, and 150 microns are approximately 1/1,700 inch. Atmospheric dust usually is considered as 10 microns or less, larger particles not being counted under the microscope in determination of dust concentrations."

Apr 1, 1942

The Bureau of Mines has long been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash-softening temperature, the free-swelling index, and the Hardgrove grindability index. Under most of these specification contracts, the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions1 issued by the Bureau of Mines, and the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor; if it is not, a price adjustment is made. The Government, with the exception of the Tennessee Valley Authority, purchased approximately 5.5 million tons of coal in fiscal year 1971. In connection with these purchases, the Bureau analyzed 4,366 samples. These are published (table 1) for the use of Government officials and the public. Such analyses of delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous sampling of coal as delivered is a check on the practical results obtained in burning the coal.

Jan 1, 1972

By M. J. Pazuchanics

This U.S. Bureau of Mines report presents results from an ongoing investigation of the use of adaptive signal discriminating methods to distinguish between cutting coal and cutting mine rock. Bit-cutting forces and tool vibration were measured in the laboratory as a linear-cutting apparatus (LCA) made constant-depth cuts in coal, sandstone, and shale test specimens. A portion of the collected data has been analyzed and some preliminary results are given here. The influence of data bandwidth, data window size, number of signal features, and voting among classifiers on classification performance are noted. Results to date, based on ideal-cutting conditions and simple geologic materials, indicate that of the four classifiers tested there appears to be no single best classifier. Usually, classification accuracy showed slight improvement as the number of features considered for classification increased. The highest classification accuracies were achieved when voting was conducted among classifiers followed by voting among force components.

Jan 1, 1991

By William J. Campbell

The Federal Bureau of Mines provided five test materials--amosite, short-and long-fiber chrysotile, crocidolite, and nonfibrous tremolite--to the National Institute of Environmental Health Sciences (NIEHS) for studies on the biological effects of orally ingested asbestos-related materials. An inter-agency agreement between the Bureau and NIEHS made possible this program to characterize these test materials. The Bureau in turn received support through contracts with the Ontario Research Foundation for the milling of amosite and crocidolite, and with the University of Maryland for microscopic measurements. The five test materials, which were supplied in quantities of 960 to 1,200 pounds each, were characterized by chemical-instrumental analysis for elemental composition, surface area, density, X-ray diffraction, infrared spectroscopy, thermogravimetric analysis, mineralogy, and particle size analyses. Particle size distributions were emphasized because of the current theories relating adverse biological effects to length-width characteristics of durable elongated particles.

Jan 1, 1980