Search Documents

By Martin Hertzberg

The concept of limit burning velocities is being used to formulate a quantitative theory of flammability limits. Competing and complicating processes dissipate power from a combustion wave and quench propagation at some characteristically low limit velocity. Two earlier reports dealt with process (a), natural convection (RI 8127); and with process (b), conductive-convective wall losses (RI 8469). This report considers process (c), radiative losses, and process (d), selective diffusional demixing. The limit burning velocity for radiative losses is [(SU)c ~ e cp] It is normally not a significant process for premixed gas flames; however, for laminar flame propagation in a gravity-free environment, it is the only loss process present. Accordingly, limit velocities at zero gravity should be much lower than on earth, and premixed gases should be flammable over wider composition ranges. For highly emissive dusts, soot, or ash-forming flames, radiative losses are significant even under normal gravity conditions. Selective diffusional demixing is a complication that manifests itself in the form of cellular flame structures and wide gaps in composition between upward and downward propagation limits. It induces a burning velocity shift (?Su)d, causing the flame to behave as though it were richer or leaner than its initial composition, depending on whether the fuel or the oxidizer mole¬cule has the higher diffusivity. A simple pertubation analysis shows that the process generates stable cellular flames whenever [dsu] > 0, where ci is the concentration of the reactant with the higher diffusivity. The same analysis indicates that at the opposite stoichiometry, where [dcu] < 0, laminar structures are stabilized. A simple formula for the diameter of cellular flames is derived, which predicts that dcell should vary inversely with the product of the diffusivity difference Di -DJ, and the burning velocity slope [dc ]. Those predictions are in good agreement with the available data. Buoyancy forces for upward propagation induce flame front curvature, and hence buoyancy and selective diffusion are mutually supportive in upward propagation. Thus large gaps in composition between upward and downward limits are present in those composition domains where cellular flames are stable.

Jan 1, 1981

By W. P. Diamond, B. M. Bench, C. M. McCulloch, Maurice Deul

As part of the Bureau of Mines methane control program, the Pittsburgh coalbed was studied in Washington and Green Counties, Pa., and in Marion and Monongalia Counties, W. Va., where this coalbed is now being mined at its greatest depth. The coalbed thickness appeared to be structurally controlled; the bed was generally thinner near the axes of anticlines and thicker near the axes of synclines. The overburden isopach shows a similar relationship. Most of the clay veins in coal occur in the synclinal troughs, generally under sandstone roof. Cleat orientations measured in 18 underground mines showed that face cleats are perpendicular to the axial trends of the folds, and the butt cleats are parallel to the axial trends, indicating structural control of the cleat. Measurement and analysis of surface joint orientations provide a method for predicting the cleat orientations of the coalbed, but linears measured from infrared photographs and photoindex sheets helped only to determine regional trends. The results of these investigations provide a geologic framework for rational planning for underground mine development to use the best available technology to cope with methane emissions, coalbed discontinuities, and related ground support problems.

Jan 1, 1975

By J. G. Donaldson

The Bureau of Mines investigated the formation of boron and boron-carbide coatings by vapor-phase reactions. Optimum parameters were determined for hydrogen reduction of boron trichloride and for the fonnation of boron-carbide coatings on graphite by reaction with the depositing boron. At 1,300° C, about 85 percent of the boron was deposited. Tungsten substrates did not react with the boron deposit; other substrates reacted to various extents. The hydrogen reduction of boron tribromide was briefly investigated. Boron carbide was deposited at 1,300° C by adding methane to the boron trichloride-hydrogen feed gas. The chemical composition of the vapor-deposited boron carbide approximated B4C. A method of etching B4C was developed to study its microstructure. When boron was deposited on graphite at 1,500° C, very hard, uniform, strongly adherent coatings of B4C were formed that might be useful in rocket nozzle applications.

Jan 1, 1968

By F. W. Wessel

This report summarizes Bureau of Mines laboratory tests of four tungsten¬-bearing materials of various grades, The test work has demonstrated that the dry reaction between sodium carbonate and scheelite is best conducted at 900° C. or a few degrees less. The sodium carbonate requirement, in addition to the stoichiometric equivalent of the scheelite, is in some inverse relationship to the grade of tungsten in the ore. Residence time and particle size exert a definite but minor control on the reaction. Pressure-digestion tests on an impure concentrate indicate the technical feasibility of extraction by this process. INTRDUCTION Over 100 years ago Oxland discovered that tungstic oxide could be removed from wolframite and converted to a soluble form by reacting the mineral with a soluble alkaline salt at elevated temperatures. He patented this discovery, and this patent 4/ since has been the basis for most tungsten extraction. Much literature exists on this process and its modifications, and the characteristics and possibilities of the reaction are quite well defined.

Jan 1, 1956

By Andrew Cecala, John Organiscak, William Heitbrink

Many types of heavy equipment used in the mining and construction industries use enclosed cabs to protect equipment operators from dust and noise exposure. Normally, when the equip- [ ] ment is new, manufacturers&apos; deigned controls are effective at keeping the operator&apos;s exposure at acceptable level. However, as equipment becomes older and many components of the enclosure deteriorate, such as gaskets and seals, the effectiveness of the enclosed cab can be greatly reduced. This can cause excessive and dangerous exposures to respirable dust, especially when the ore or overburden contains crystalline silica.

By A. J. Kraemer

The properties of crude petroleum continue to interest the Bureau of Mines and constitute an important phase of its major studies on the mineral resources of the United States. The Bureau&apos;s interest in the subject has been intensified by frequent requests for information on the characteristics of crude petroleum from various producing fields. Since its inception the Bureau of Mines has collected and analyzed samples of typical oils and at present has surveyed and classified crude petroleums from nearly all the known oil fields of the Western Hemisphere. Results of these surveys have been presented in various Bureau of Mines publications. (See bibliography, appendix A, p. 145.) The nature and comparative value of crude oils from various countries and the extent to which these oils may be considered potential competitors for markets are of manifest importance to the petroleum industry in all lands, largely because all crude oils, wherever produced, are either actual or potential competitors for a market with all other crude oils. The numerous discussions of foreign production of oil that have appeared in the technical press in the past indicate the great interest of the United States in this subject.

Jan 1, 1937

By Steven J. Schatzel, Gerrit V. R. Goodman, Robert B. Krog, C. Özgen Karacan, Gabriel S. Esterhuizen

Although longwall mining productivity can far exceed that of room-and-pillar mining, the total methane emissions per extracted volume associated with longwall sections are generally higher than those for continuous miner or pillar removal sections. Increased face advance rates, increased productivities, increased panel sizes, and more extensive gate road developments have challenged existing designs for controlling methane on longwalls. Methane control research by the National Institute for Occupational Safety and Health (NIOSH) recently examined a number of practices designed to maintain concentrations in mine air within statutory limits and consistently below the lower explosive limit. These included a reservoir modeling approach to predict methane inflows in gate road entries. The outputs sug­gested that emission rates in the gate roads decreased with the use of shielding boreholes and increased degasification time. Also, mining perpendicular to the face cleats liberated more gas into the mine workings, emissions were almost a linear function of Langmuir pressure and volume, and emissions were inversely related to sorption time constant. Subsequent simulations predicted changes in methane drainage using in-seam boreholes. The results showed that longer degasification times resulted in lower face emission rates. Premining degasification produced more methane than that produced during panel extraction, a fact attributed to the already decreased methane content of the coalbed. This work concluded that longer premining degasification periods would be more advantageous to the operator. The industry trend toward increasing longwall face width can produce increased methane emissions from the face due to a higher volume of cut coal on the face conveyor. Two methods were used to estimate face methane levels on longer faces. In the first method, segmented methane data were extrapolated for greater face widths. The second method estimated emissions contributions from the shearer, face conveyor, panel belt, longwall face, and ribs, and summed these for wider panels. Permeability changes in the gob behind the longwall shields were estimated using a NIOSH-developed numerical model. The results showed that permeability was highest near the edges and corners of the gob.

Jan 3, 2008

By W. Bruce Montgomery

Manganese oxides occur, with some iron oxides, in small scattered lenses on property controlled by the Columbia Manganese Co. (1943) near Evington, Campbell County, Va. The company mined some manganese ore during 1917 and 1918. A preliminary examination in May 1942 indicated the possibility of finding additional ore. On August 21, 1942, the Bureau of Mines began prospecting to verify the continuity of the ore exposures. Work on this project continued until February 5, 1943. Prospecting and development work included shaft sinking, crosscutting, drifting, trenching, and test-pitting in six separate areas indicating two types of deposits. The most predominant type is a wide brecciated area in which occur lenses or pockets of nodular manganese oxides. The other type is characterized by more of a vein structure, including thin layers of manganese oxides.

Jan 1, 1949

By C. M. Keenan

During the 7-1/2 years (January 1945-June 1952), immediately preceding enactment of the Federal Coal Mine Safety Act, 26 major disasters3/ in the coal mines of the United States caused the deaths of 491 persons. In the next 7-1/2 years under the act (July 1952-December 1959), only 12 major disasters occurred. The total killed was 148. This improvement is commendable. However, the continuing frequency of minor fires and gas and/or dust ignitions in the Nation&apos;s coal mines, many of which could have been of major consequence, are cause for serious concern to the coal-mining industry and those affiliated agencies engaged in promoting safety in the industry. The data presented in this report have been prepared to make available to the coal-mining industry and related groups an overall perspective of the disaster potential from mine fires and gas and/or dust ignitions in coal mines after 7-1/2 years under the Federal Coal Mine Safety Act. This act, effective July 16, 1952, which amended the original Federal coal-mine investigative act of May 1941, provides under Title II certain enforcible mine-safety provisions designed to prevent major disasters caused by explosions, fires, inundations, and man-trip and man-hoist accidents in coal mines that employ 15 or more individuals underground.

Jan 1, 1960

Water infiltration control techniques are designed to reduce the total volume of water entering an underground mine, and thus, reduce the volume of mine water discharge During the development of underground mines, water may be encountered in various quantities This water must be pumped from the mine during active mining, and in many situations, the weight of water removed will be more than the total weight of mineral extracted After abandonment of the mine, infiltrating water either floods the mine workings or discharges from the mine (27, 127) Infiltrating water may enter underground mines from above, below, or laterally through adjacent rock strata Earth fractures such as faults, joints, and roof fractures resulting from surface subsidence are commonly primary causes of water entrance Into abandoned underground mines Factors affecting the quantity of water entering a mine will be the depth of the mine, location of water bearing strata, and ground water flow patterns Investigations of the quantity of water entering underground coal mines have found the average rate of infiltration to range from approximately 6,262 to 10,280 liters per hectare per day (670 to 1,100 gal/acre/day) (27) Water flowing through underground mines flushes pollutants from the mine and may result in their discharge to the environment A reduction in the amount of flow usually results in a reduction in total pollution load discharging from the mine The techniques discussed in this section can be used to reduce the volume of surface and groundwater available to enter the mine system and transport pollutants The selection of a control technique will depend upon the characteristics of the mine system and the expected cost effectiveness of the technique In order for water infiltration control to be effective in controlling mine drainage pollution, the reduction in mine water flow must not be accompanied by an increase in concentration of pollutants (127) REFERENCES 2, 27, 51, 58, 127, 132

Jan 1, 1975

By Gregory B. Beacher

Analyses have been performed on geotechnical properties of copper, uranium and phosphate (gypsum) tailings materials, with the intent of identifying typical measures of variability within and among sites, and of characterizing such variability for use in reliability modeling of tailings embankments. In all, data from approximately 41 sites were analysed. Fairly consistent results were obtained for within site variabilities. However no one probabilistic model was found to be applicable to all sites. The distributional forms for most of the data sets are regular, and tend toward Normality when spatial trends are removed. At many of the sites sufficient in situ data were available to allow estimates of vertical autocorrelation distances and measurement noise. Available data indicate that variability in pore pressures may have a more important effect than strength property variation. A major problem in interpreting available strength property data results from the unknown drainage conditions during testing.

Jan 1, 1983

By Terry J. Close

The Anaconda Pintlar Wilderness has a significant mineral resource potential. Five deposits have resources totaling about 180,300 tons (163,600 t) containing silver, copper, lead, gold, and zinc. Another 11, not sufficiently exposed to allow resource estimates, may have additional mineral potential. No placer deposits are indicated. There is little potential for the production of sand, gravel, or stone; alternate sources are closer to markets. No oil, gas, uranium, or geothermal energy sources are known to be present.

Jan 1, 1982

By N. S. Dalal, X. Shi

"Electron spin resonance (ESR) measurements on solutions and isolated powders provide direct evidence for the involvement of Cr(V) species in the reduction of Cr(VI) by NAD(P)H. ESR analysis of an isolated Cr(V)NAD( P)H solid yields 6 11 = 1.9831 and 6.i. = 1.9772, indicating that the unpaired electron occupies the d22 orbital of the Cr(V) ion, with square-pyramidal geometry. Addition of hydrogen peroxide (H2 0 2 ) to the N AD(P)HCr( VI) reaction mixtures suppresses the Cr(V) species and generates hydroxyl (""OH) radicals. The ""OH radicals were detected via ESR spin trapping, employing 5,5-dimethyl-1-pyrroline-N-oxide and a-(4-pyridyl-1- oxide)-N-tert-butylnitrone as spin traps. The dependence of Cr(V) and ""OH radical formation on the H20 2 and Cr(VI) concentrations indicates that the Cr(V) species react with H20 2 to generate the ""OH radicals. Similar results were obtained by using various diols (arabinose, cellobiose, FAD, fructose, glyceraldehyde, ribose, and tartaric acid), a-hydroxycarboxylic acids, and glutathione. Investigations with superoxide dismutase showed no significant participation of 02 in the generation of OH radicals. These results thus indicate that the Cr(V) complexes, produced in the reduction of Cr(VI) by cellular reductants, react with H20 2 to generate ""OH radicals, which might be the initiators of the primary events in the Cr(VI) cytotoxicity.In this paper we report an electron spin resonance (ESR)3 spectroscopic detection of Cr(V) species in the reduction of potassium dichromate, henceforth called Cr(VI), by NAD(P)H and other diols. Also reported here is the detection of the hydroxyl (""OH) radical in the reaction between hydrogen peroxide (H2O 2) and a variety of Cr(V) complexes. This work was undertaken because while the reduction of Cr(VI) to lower oxidation states has been suggested as a key step m the mechanism of Cr(VI) toxicity, mutagenicity, and DNA alteration, the details are not yet clear (1-5).Earlier studies on the mechanism of Cr(VI) reduction in cellular systems include those on the reduction of chromate by microsomes (6-8), rat liver DT-diaphorase (9), and aldehyde oxidase (10). All these studies imply that Cr(VI) can be reduced to Cr(Ill) by cellular constituents. Regarding the mechanism of Cr(Vl) carcinogenicity, Jennette postulated that Cr(V) is the ultimate carcinogenic form of chromium compounds (8). This conclusion has led to many further investigations of the formation of Cr(V) in the reduction of Cr(VI) under biologically relevant conditions (11-33). More recently, however, Kawanishi and co-workers (34) have investigated the mechanism of DNA cleavage induced by Cr(VI) in the presence of H20 2 and have argued that it is not Cr(V) itself that is carcinogenic, but it is the reactive oxygenated species (02, 10 2 , ""OH) (produced by the decomposition of the Crv(02) ¾ - ion) that cause the DNA alteration."

Jan 1, 1990

By E. P. Youngman

This paper is one of a series of digests of foreign minim legislation and court decisions that is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countries. This interpretation of the minim lams of Ceylon has been prey tired from the best available information in Washington and is released subject to amplification and correction, if necessary, by United States foreign-service officers. INTRODUCTION Ceylon has no basic mining law; the general rules governing the granting of mineral concessions and affecting legal titles of concessionaires are laid down in Ceylon Government ordinances or are found in the authorized forms for licenses and leases. The material available in the preparation of this digest is as follows:

Jan 1, 1933

PURPOSE: Evaluate practical technological advances in level-dependent hearing protectors and inexpensive personal acoustic monitors. RESEARCH SUMMARY: The results of previous NIOSH research show that miners develop hearing loss much more quickly than nonoccupationally noise-exposed individuals and that miners experience a greater severity of hearing loss than would be expected for nonoccupational noise-exposed persons of the same age and gender. Using hearing thresholds at 4,000 Hz as an indicator, coal miners experience hearing loss 2.5 to 3 times greater than would be expected for persons not exposed to occupational noise. At age 50, 90% of coal miners and 49% of metal/nonmetal miners were found to have a hearing impairment. In comparison, only 9% of a nonoccupationally exposed control group had a hearing impairment at age 50.

Jan 1, 2000

By Richard D. Miller

The helium resources base of the United States was estimated by the Bureau of Mines to be 961 Bcf as of January 1, 1983. These resources are divided into four categories in decreasing degree of assurance of their existence: (1) helium in storage and in proved natural gas re- serves, 271 Bcf, (2) helium in probable natural gas resources, estimated at 202 Bcf, (3) helium in possible natural gas resources, estimated to be 351 Bcf, and (4) helium in speculative natural gas resources, which makes up the remaining 137 Bcf. These helium resources are further divided into depleting, nondepleting, and stored classifications. The depleting resources are those associated with natural gas fields that are, or will be, produced for the natural gas they contain. All of the helium in potential (probable, possible, and speculative) natural gas resources is included in this classification. These depleting resources are estimated to contain 789 Bcf of the total helium resource base. Helium resources contained in nondepleting natural gas resources, those in shut-in, abandoned, or otherwise nonproducing natural gas fields, are estimated to total 134 Bcf. There is 38 Bcf of helium in storage in the Federal Government- owned Cliffside Gas Field near Amarillo, TX.

Jan 1, 1985

By Terry S. Cory

This report describes the results of a measurement and analysis program to characterize wireless radio transmission in metal/non-metal mines over a wide frequency range from 0.2 - 1000 MHz and over a variety of mine environments. Six mines were chosen based on the relative economic significance of their product to the U.S. economy. Mine types include oil shale, uranium, potash, lead/zinc, copper, and silver. Particular mines were chosen so that the group would embody the most important mining techniques. The results show that transmission at medium frequencies are optimum for wireless mine communications, in agreement with extensive testing previously performed by the authors In coal mines, and that mine-wide wireless systems are feasible with a minimum requirement for new dedicated wiring. At least one need for such a wireless system was identified in each mine visited.

Aug 1, 1981

By T. F. Mitchell

As a part of the program of investigation of domestic sources of manganese ore, mining engineers of the Bureau of Mines examined and obtained samples of ore from two properties in the vicinity of Bettie Mountain, Lander County, Nev. In addition, samples from three claims in the Carico Lake region, Lander County, Nev., were submitted by private interests. RS the ores were too low in grade to be acceptable for the direct production of ferromanganese, their amenability to concentration by ore dressing was investigated. The Black Bock property is 16 miles south of Valmy, Nev., and is owned by Western Alloys, Inc., Salt Lake City, Utah. The deposit is a replacement of sedimentary rock by manganese oxides. Ore occurs in two main ore bodies designated as the "upper bench" and "lower bench", which could be mined separately. Examining engineers obtained samples from each ore body, and laboratory experiments were made on each sample. The Black Eagle group of claims is in Lander County, Nov., about 43 miles southwest of Battle Mountain. Ore occurs as a replacement of manganese oxides in shale and chert. The 2-ton sample of ore used for laboratory testing was taken by a Bureau of Mines examining engineer from an adit that partly transversed a 28-foot bed of ore. The property is controlled by Western Alloys, Inc.

Jan 1, 1951

By Dean H. Ambrose

This Bureau of Mines publication summarizes the status of mine electrical equipment reliability research. Failure rate data were estimated from theoretical, laboratory, and field studies. Tables are presented listing reliability characteristics of molded-case circuit breakers, undervoltage relays, ground check monitors, cables, motors, and control circuitry. Application of failure rate data is shown in tables listing maintenance scheduling intervals of components and components that are most sensitive to the probability of hazardous voltages on power distribution systems in the mines. Complete, accurate, and appropriate failure rates on mine equipment are of the utmost importance for reliability evaluations.

Jan 1, 1985

By Manuel Gomez

A computerized moving average technique was developed to interpolate coal seam characteristics between sample points. The interpolative method coupled with multivariate regression analysis and simulation procedures was used to forecast coal properties not readily obtained from an analysis of drill core samples. Coal property forecasts were of two kinds: (1) specific mine property forecasts that are suitable for mine product control and yield a good approximation of the local variation along both the vertical and horizontal axes of the seam, and (2) regional estimates where much of the local seam variation is smoothed out, but the general trends are maintained. Forecasts of the volatile matter, ash, total sulfur, and the heating value for part of the Pittsburgh seam located in Ohio, Pennsylvania, and West Virginia were in good agreement with independent evaluation data. Spatial configuration for preparation characteristics, particularly, the effect of crushing on sulfur release, low-and high-temperature carbonization properties, the Hardgrove grindability index, the coal hardness index, gasification variables, and hydrogenation factors were constructed for the same area of the Pittsburgh seam. These forecasts may be developed from drill core data collected in the exploration phase of mining. The results, which may take the form of a series of maps, are useful to mining, chemical, and combustion engineers, to economists and mine managers, as well as to coal users for mine design, economic analyses, energy forecasts, utilization studies, mine product control, and environmental control and programming.

Jan 1, 1974