Search Documents

By Maria I. De Rosa

Combustible materials, when burned, produce toxic gases and smoke, which may vary dramatically from one material to another, with resultant different total toxicity and smoke obscuration levels. This U.S. Bureau of Mines report presents smoke property data acquired for a variety of mine combustibles and shows that there exists a correlation between the smoke properties, the relative toxicity, and the smoke obscuration levels of those combustibles tested. These correlations can be used to devise simple, standard tests for determining the toxic and smoke obscuration hazards of mine materials during fire.

Jan 1, 1989

By Leon W. Dupuy

"INTRODUCTION Scheelite occurring in tactite at the Black Rock tungsten mine, near Benton in Mono County, Calif., was investigated by the Bureau of Mines in cooperation with the Geological Survey as part of their search for additional sources of supply of strategic minerals authorized under the Strategic Materials Act. 3/4/The work accomplished by the Bureau, and the assays of samples taken are described in this manuscript. The ore found aided materially in prolonging the operating life of the mine during the recent national emergency, supplying much-needed tungsten for war use. ACKNOWLEDGMENTSIn its program of investigations of mineral deposits, the Bureau of Mines has as its primary objective the more efficient utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. The Mining Division, under the direction of Lowell B. Moon, chief, conducts preliminary examinations, performs the actual development work, and prepares the final report. The Metallurgical Division, under the direction of C. C. Ralston, chief, analyzes samples and performs beneficiatibn tests."

Mar 1, 1948

By K. P. V. Lei

An electrochemical process was developed for the preparation of vanadium from vanadium carbide. Commercially available vanadium carbide (V2C) was used as the starting material. Vanadium was obtained by electrolysis of the V2C in a BaCl2-KCl-NaCI-VCl2 electrolyte at 670° C using a helium-atmosphere, molten-salt electrolytic cell. Vanadium products were recovered with purities high as 99.6 percent. Current efficiencies of 87 percent and vanadium recoveries of 84 percent were attained. The cathode products were amenable to electrorefining to high-purity vanadium of 99.96-percent purity.

Jan 1, 1971

This report presents a Bureau of Mines study comparing the construction costs, leakage measurements, and predicted performance of different types of large stoppings built and tested in a room-and-pillar oil-shale mine. The six full-sized structures (30 ft high by 55 ft wide) included both permanent and temporary stoppings and were fabricated using materials ranging from structural steel to coated brattice cloth. Leakage across each stopping was measured at differential pressures ranging up to 1.0 in w.g., using both the brattice window method and sulfur hexa-fluoride (SF6) tracer gas. Blast air pressures resulting from a full-scale face blast of approximately 1,800 lb of ammonium nitrate-fuel oil (ANFO) explosives were measured across two of the stoppings and the pre-and post-leakage rates were compared for all the stoppings. Overall performance of the stoppings for production applications was evaluated using an operational model of a two-panel oil-shale mine. Different combinations of temporary and permanent stoppings were evaluated based upon ventilation performance and construction and operating costs.

Jan 1, 1988

By Richard A. Thomas, Michael J. Sapko, Gary L. Mowrey, William D. Monaghan, Michael A. Trevits

Over the years, more than 20,000 mine seals have been erected in underground coal mines in the United States. Seals are used extensively in underground mines to isolate worked-out areas, active mine fire zones, and to control water inundations. Seals are most often built directly in the mine and can be fabricated from blocks made of wood or cementitious material. Recently, several explosions occurred within sealed areas of underground U.S. coal mines. These explosions, believed to be initiated by lightning strikes on the surface, destroyed numerous seals and caused considerable damage external to the sealed area. The National Institute for Occupational Safety and Health is conducting research to develop design guidelines, to investigate noninvasive techniques to characterize seal strength properties, and to evaluate seal test methods. As part of this work, a 30-ft wide, 16.1-ft tall and 4-ft thick seal was built in an underground experimental mine using cement and foamed water. Two types of noninvasive techniques are currently being investigated, namely the Schmidt Hammer for measuring compressive strength and ground penetrating radar (GPR) for detecting the presence of anomalies (e.g., voids, discontinuities) within the seal. Once these noninvasive tests were completed, the seal was subjected to destructive explosion testing. This study presents the results of the Schmidt Hammer tests, GPR scans, and the characteristics of seal failure during explosion testing.

By Arno C. Fieldner

Coal for coke production is fundamentally necessary for the manufacture of pig iron , and pig iron must be had for making steel - a vital element in our modern industrial economy . In both World Wars , special effort by Government and industry was required to meet the emergency of greatly increased demands . In the first World War , lack of coke - oven capacity , rather than lack of coking coals , was the principal problem ; but in the second World War both oven capacity and coking -coal mining capacity were pushed to the utmost . Because of inadequate supply , it became necessary to allocate a part of the production of these coals from other fuel use to coke production . This was done by the Solid Fuels Administration . These experiences raised a question , during and after the war, as to the nature and amount of the minable reserves of coking coal suitable for the manufacture of metallurgical coke ; and to what extent the lower -rank and lowergrade coals could be utilized by improving preparation and by appropriately blonding different coals . Obviously , much investigation and research are required to find answers to these questions . Somo work was done by Governmental and industrial agencies during the war , and , fortunately , more has been undertaken since the close of It is the purpose of this paper to review briefly our fuel reserves , with special reference to coking coal , and to discuss the problems of utiliz . ing progressively poorer coking coals as the reserves of high - quality coals approach depletion .

Mar 1, 1950

By L. A. Neumeier

The Bureau of Mines evaluated creep and other properties of extruded Zn-30 pct-AI alloys containing 0 to 0.7 pct Mg. The alloys were extruded both above and below the Zn-Al eutectoid temperature of 275° C. Creep behavior is defined for the alloys as extruded and after various heat treatments. Tensile properties, hardness, thermal expansivity, impact resistance, and microstructures are given. The alloys, either with or without magnesium, required substantially less pressure for extrusion near 275° C than at higher or lower temperatures. The alloys containing magnesium exhibited significantly greater hardness, tensile strength, and creep resistance, but much lower ductility than the 2n-30 pct Al alloy. The properties were very sensitive to the processing conditions.

Jan 1, 1971

By Slavoljub D. Maksimovic

At some coal mines, methane gas is released during raise drilling. At the request of the Mine Safety and Health Administration (MSHA), U.S. Department of Labor, the Bureau of Mines conducted ventilation surveys at different raise drill sites to assess various methods of reducing methane concentration. The resulting data indicate that raise drill shaft cavities are ventilated by air compressors, vacuum pumps, auxiliary blower fans, and free intake air from the surface. The compressors, pumps, and fans operate simultaneously or separately. At the bottom of the shaft cavities, ventilation is controlled by regulators and airlocks. Methane is monitored, measured, and periodically sampled on the surface, at the bottom, and at different levels in the shaft cavities. Maximum concentration of 3.5 percent was measured in one shaft in West Virginia. Air velocity down the raise drill shafts is always very low, Maximum recorded air down the drill stem was 3,000 cfm, which can be increased by adding air compressors. The best way to ventilate shaft cavities is through the simultaneous use of air compressors and vacuum pumps. If the methane concentration cannot be reduced with additional compressors, then the inside diameter of the drill rod should be increased, or larger pilot hole drill bits should be used.

Jan 1, 1981

By T. L. Hebble

The Bureau of Mines investigated a hydrometallurgical procedure to recover Co, Ni, and Cu from an electrolytic zinc industrial copper filter cake. The copper filter cake is presently unmarketable or of low value because economic and environmentally acceptable processing technology is lacking. Research by the Bureau of Mines has developed a multistage process for recovering or recycling over 93 pct of the Zn, Cd, Cu, Co, and Ni from this material. The stages involved are (1) wet sizing, (2) H2S04 leaching of undersized material, (3) H2S04-Mn02 leaching of H2S04 leach residue, (4) selective precipitation of As, Cu, and Co-Ni products, and (5) precipitation of manganese for recycling to the leach circuit. The final process residue is only 1.6 wt-pct of the initial cake and consists of lead sulfate.

Jan 1, 1981

Develop technology that can reduce the dust exposure of a mine worker at the tailgate end of the longwall face by providing him with a clean split of air. Approach Use the jet spray air mover (JSAM) developed under a Bureau of Mines contract (refer to Technology News No. 117 for details on the development), to clean a small portion of the face air and to discharge the clean air behind a brattice partition. How It Works At most longwalls, air flows along the face from head-to-tail. Most of the airborne respirable dust generated along the face during mining is transported to the tailgate with the airflow. Any miner required to work at the tailgate is exposed to this dust. The only practical means of removing airborne respirable dust is with a scrubber. Simplicity and size made the JSAM the best choice for cleaning a portion of the tailgate air. The scrubber has no moving parts and is operated by water at low flow rates (<10 gpm) and fairly high pressures (250-500 psig). Many longwalls have sufficient water systems to supply the JSAM with adequate water pressures and flow rates. Also, the JSAM&apos;s size (4&apos;x 2&apos;x 1&apos;) allows it to be hung on one of the tailgate&apos;s shields or at some other convenient location. A clean split can be maintained at the tailgate by discharging the cleaned air behind a brattice partition at the work area. This should effectively seal off the clean air from the dusty air and provide the tailgate worker with a less dusty work environment.

Jan 1, 1983

By J. P. McGee

As part of a joint U.S. Atomic Energy Commission-Federal Bureau of Mines program for using nuclear energy to supply process heat, a simulated nuclear loop has been constructed to test components. This loop has been operated for more than 1,800 hours at 100 p.s.i.g. Of this period, 23 hours were at 2,500° F. and higher; 540 at 2,000° to 2,500° F.; 840 at 1,500° to 2,000° F.; 200 at 1,000° to 1,500° F.; and 260 below 1,000° F. Leakage at flanges and welds was not a serious problem. A helium-recycle system with gas temperatures of 2,300° to 2,500° F. and a static pressure of 250 p.s.i.g. appears feasible. Difficulties were encountered with the recycle compressor due to thermal distortion of the impeller and shaft. The use of sealed bearings limits compressor operation to the life of the bearings.

Jan 1, 1960

By Valois R. Shea-Albin

An accurate assessment of the vertical stress on a coal seam at depth is important for mine design. Vertical stress calculation techniques presently available either are not sufficiently accurate or cannot handle complex surface topography. Therefore, the U.S. Bureau of Mines developed a computerized method to calculate vertical stress exerted on surfaces at depth that includes the effect of topography. Two input data sets are required: a digital elevation model containing topographic elevations and a coal seam file defining coal seam elevations at depth. Boussinesq&apos;s equation then quantifies the vertical stress resulting from topography. The computerized method was tested on a coal seam overlain by a complex topography where a vertical stress map encompassing several square miles was produced. Results show that depth mitigates the affects of surface topography, while the coal seam topography has a direct effect on the vertical stress. In comparison to the computerized method, the direct stress method overestimates stress under hills and underestimates stress under valleys. The largest difference between the two methods occurs under the steepest topographic relief. A limitation of the computerized method is that stresses cannot be accurately determined near an outcrop.

Jan 1, 2010

By Elizabeth G. Baglin

Research was conducted by the Bureau of Mines to determine the feasibility of using electrokinetic densification to dewater Bayer process red mud, magnetic black mud prepared by pressure digestion of red mud in the presence of ferrous sulfate, and magnetic black mud formed by simu-lated Bayer digestion of Jamaican bauxite with added ferrous sulfate. Tests showed that the solids content of presettled muds could be increased from 25 pct to approximately 40 to 48 pct by gravity draining followed by electrodewatering for approximately 48 h. Electrodewatering may not be practical because of increased reagent and processing costs and because the muds must be thoroughly washed prior to electrodewatering to remove dissolved ions and decrease mud conductivities.

Jan 1, 1988

By H. H. Dewing

The U.S. Bureau of Mines characterized Hg-containing wastes and used a thermal-desorption process to remove and recover the contained Hg. The wastes were generated by an electrical-parts plant engaged in the assembly of Hg-containing switches and contained phenolic resins and paper insulating materials mixed with soil. The average Hg content was 396 ppm. Numerous characterization tests showed the Hg was tightly absorbed and could not be removed or concentrated by leaching or gravity separation techniques. Laboratory retort tests showed the Hg content reduced to < 16 ppm in 2 h at 400 °C; rotary-kiln, thermal-desorption tests required 4 h at 450 °C. Airflow through the retort im¬proved thermal-desorption efficiency, but vacuum operation only slightly reduced the temperature needed for thermal desorption. Offgases from decomposition of organic materials were burned in a high-temperature afterburner and subsequently cooled in a heat exchanger to condense water vapor. Finally, the Hg vapor was condensed and absorbed from the offgas by activated charcoal. Mercury recovery was over 99.99 pct of the desorbed Hg. Thermal-desorption processes have had wide application to many Hg-containing wastes, and historical experience in Hg mining has demonstrated its potential cost effectiveness.

Jan 1, 2010

By Ann G. Kim

The Bureau of Mines estimated the methane content of a coal, which depends primarily upon rank and pressure, from the adsorption equation V kpn, where k and n are constants related to rank. By incorporating corrections for moisture, ash, and temperature, and estimating pressure and temperature as a function of depth, the methane content of coal in place can be estimated from the following equation: [ ] Values calculated with this equation generally are in reasonable agreement with direct determinations. By assuming a standard moisture and ash content, and using the hydrostatic head to estimate pressure, a graph of rank and depth versus gas content was constructed. Although estimated values were consistently high for several high-volatile bituminous coals from an area where the pressure is known to be less than hydrostatic, the estimated methane content for most coals shows reasonable agreement with values determined by the direct method.

Jan 1, 1977

By R. J. Tocher

Uniaxial testing was performed on coal specimens to determine the time-dependent response. The testing was carried out on coal from six mine sites throughout the Western United States and Pennsylvania. Testing configurations were varied to allow analysis of moisture dependency, stress level and specimen orientation. Several theories were presented for the behavior of coal due to moisture diffusion. Experimental results showed the correlation between the theories and the actual material response. Coal deformation was found to be highly dependent on the moisture level of the testing environment. Moisture migration causes drying and shrinkage which lead to progressive degradation of the material. The coal tested experienced a rebound if saturated after a period of drying. This type of time-dependent behavior overshadows the dependence on the applied stress level, which, however, still produces a noticeable creep behavior. Analysis of one series of creep test results was performed. A relationship was developed on the basis of a simplified rheological model to describe the coal response to uniaxial stress. Previous empirical formulations in the form of power laws were compared and their deficiencies pointed out.

Jan 1, 1980

By d&apos, Kathleen J. Amico

THIS SUMMARY appears in Minerals Yearbook volumes I and III, which cover mineral production in the United States, its island possessions, the Canal Zone, and the Commonwealth of Puerto Rico, as well as the principal minerals imported into and exported from the United States. The several commodity and area chapters contain further details on production. A summary table comparing world and U.S. mineral production also is included. Mineral production may be measured at any of several stages of extraction and processing. The stage of measurement used in the chapter is normally what is termed "mine output." It usually refers to minerals in the form in which they are first extracted from the ground, but customarily includes for some minerals the product of auxiliary processing operatons at or near mines.

Jan 1, 1963

By John Durkin, Roy J. Greenfield

This report discusses the configuration and system deployment for the postdisaster surface seismic system for detecting and locating trapped miners. It analyzes the results of 15 field tests to define a signal model, background noise levels, and subarray performance. A waveform modeling procedure is described and compared with observed waveforms. The resulting similarity indicates that the major factors affecting the signal amplitude, waveform, and spectral character are understood. A model is presented which gives the signal amplitude as a function of source type, source depth, and horizontal off- set between source and receiver. Using this model a curve is presented which gives the range at which a signal will be detected for different signal and noise levels. Finally, and most important relative to the mission of the sys- tem, the ability of the system to detect signals on one or more subarrays is put into a probabilistic framework. For a strong source it is almost certain that a subarray directly over the source will detect the signal. After signal processing, it is highly likely that signals will he detected on sufficient subarrays to locate the trapped miner. Location errors have been found to be less than 100 ft in the majority of cases. Techniques have been used that can reduce the location errors to this level even when soil layer variation between subarrays is severe.

Jan 1, 1981

By Michael G. Pojar

This Bureau of Mines report estimates the population of the principal types of machinery in use by the coal mining industry during 1982 in surface and underground mines. Estimates were arrived at using 1976 coal equipment population estimates as baseline data with modifications made for new mine development, expansion, and closure occurring during 1976-82. Estimates were broken down into 3 regions which included all 26 coal-producing States. Modifications made to the baseline data were computed using (1) actual equipment information when available, plus (2) equipment information hypothesized from representative generic mine models, which were predicated on mine size and mine method. Roughly half of the equipment fleet at new or expanding coal operations was known; the remainder was hypothesized. The mine models used to generate equipment information are included in this report, along with the hypothesized equipment use data. The equations and various factors used to determine the equipment adjustments for mine closings, new mine openings, and small coal mine operations are also identified.

Jan 1, 1986

By Gregory M. Molinda

The U.S. underground coal miner faces a continuing hazard from the fall of roof. At the root of many injuries and fatalities are weak or defective roof strata. Throughout mining history, millions of miles of entry have provided exposure of every conceivable geologic roof hazard. This report describes the geologic origin, association, and potential danger from the most common hazards. Discussions of weak rock include drawrock, rider coals, head coal, stackrock, and stream valley effects. Discontinuities, or roof defects, are described including, clay veins, slickensides, joints, and paleochannels. A number of examples from U.S. coalfields are used to document geologic structure and associated hazards. Roof fall analysis is a methodology used by NIOSH for hazard recognition and prevention; its application and benefit to the industry are discussed.

Jan 10, 2003