Search Documents

By T. E. Gray

This report describes the preparation characteristics of the significant coalbeds in Nicholas County, W. Va. It is one in a series describing coals suitable for producing metallurgical coke, either as mined or after beneficiation. Almost 5 million tons of coal were produced in Nicholas County, W. Va., in 1960, of which over 2.6 million tons were cleaned in eight preparation plants. It has been estimated that over 6 billion tons remained in the county as of December 31, 1960, in beds 12 inches and more thick.

Jan 1, 1962

By Paul M. Tyler

[This paper presents one of a series of digests of foreign mining legislation and court decisions which is being prepared in advance of a general report relative to the rights of American citizens to explore for minerals and to own and operate mines in various foreign countries. This interpretation of the mining laws of specified French possessions in Africa has been prepared from the best information available in Washington, but is released subject to correction and amplification, if necessary, by the proper American diplomatic and consular officers, to whom it is being referred through the courtesy of the Department of State. France controls large areas on the African continent, but the various Colonies and Dependencies are administered more or less independently. Algeria is under the direct jurisdiction of the Ministry of the Interior, and its mining laws are essentially the same as those of the mother country. Tunis and Morocco are attached to the Ministry of Foreign Affairs; separate digests of the mining laws' of these respective colonies have already been prepared by the United States Bureau of Mines. The present paper covers all other French territory on the continent of Africa except Somaliland, a rather small Colony including the port of Djibouti near the point where the Red Sea joins the Gulf of Aden. Available information indicates that the prospects of mineral production in this Colony, apart from salt and gypsum, are not at all encouraging.3]

Jan 1, 1933

By John C. Machisak

Employment and related injury experience of the coking industry in the United States for 1956 contained in this publication is summarized under three general sections: (A) General injury experience: Tables 1 to 9: Current and comparable statistics on operating data, number, frequency, and degree of severity of injuries and major accident agencies involved in the cause of injuries. Data are presented for the industry as a whole, for each type of oven, and for the States in which coke was produced. (B) Selected injury experience: Tables 10 to 15: Comparable injury data covering 5- and 10- year periods on the number and degree of severity of injuries and major accident causes.

Jan 1, 1958

By L. L. Oden

The Bureau of Mines is conducting research to develop methanation catalysts for converting synthesis gas derived from coal to synthetic natural gas. This report describes a method to prepare supported Raney nickel coatings by dipping screen-covered nickel sheet in molten aluminum-nickel alloy. Coatings were formed at 1,050° C that were comparable in thickness, composition, microstructure, and catalytic properties to flame-sprayed commercially pre-pared Raney nickel. A molten salt comprising cryolite-8 wt-pct LiF was employed over the molten metal bath to clean and preheat the substrates, to protect the metal bath from oxidation, and to heattreat the coated specimens. Immediately following heat treatment, specimens were quenched to 700° C in a molten salt bath containing CaC12-34.5 wt-pct NaCl, which also functioned to remove the insoluble occluded fluoride salt.

Jan 1, 1976

By Daniel I. Carey

Current and potential dragline reclamation usage was evaluated for the U.S. coalfields based on data gathered and analyzed during field surveys, literature reviews and contacts with manufacturers. It was concluded that current mining plans have been adapted to federal and state strip mine and reclamation laws in ways which limit the potential for dragline reclamation systems at active mine sites. At abandoned conventional contour mine sites in steep-sloping areas such as central Appalachia, however, it was found that dragline reclamation systems have great potential application and may be the only practical solution to many reclamation problems. Alternative dragline systems were examined for restoring abandoned sites, and it was concluded that a tower excavator system offered superior characteristics and should be evaluated and developed under field conditions. A testing program was developed to provide a framework for the monitoring and analysis of cost, production and environmental data during a field demonstration of a tower excavator system.

Jan 1, 1981

By Martin Hertzberg

The concept of limit burning velocities is used to formulate a quantitative theory of flammability limits. Competing processes dissipate power from a combustion wave and quench propagation at some characteristically low limit velocity. There are four competing processes and one complication: (a) Free, buoyant convection, (b) conductive-convective wall losses, (c) radiation, (d) selective, diffusional demixing (the complication), and (e) flow gradient effects (flame stretch). These complexities are unraveled by creating an idealization that is initially freed from these competing processes. The ideal serves as a standard, and its burning velocity (Su), ideal is a unique function of the initial thermodynamic variables of state. By adding each process individually, it is possible to evaluate their significance, quantitatively, in terms of a limit velocity (Su)a , b , c , or e , and to explore the nature of their cooperative interactions. The larger the limit velocity, the more significant the process. The apparently diverse observations of flammability behavior are readily unified within this simple, conceptual framework.

Jan 1, 1976

By Cleo G. Rall

The method for determining the effective porosity of oil- and gas-bearing sands described in this report is a development of earlier methods (28)3/ devised by the Bureau of Mines. The apparatus bas been improved and made more convenient to use, but the procedure is essentially the same as that which has been in use for maw years. A tabulation at the end of the report gives the results of more than 4,800 porosity determinations for oil sands4/ in the fields of 13 States, A selected bibliography of references to articles containing descriptions and evaluations of various methods of' determining porosity is included in this report. The method was devised and developed at the Petroleum Experiment Station at Bartlesville, Okla., as part of the Bureau's research on fluid-energy relationships and on methods of improving the recovery of crude oil from underground reservoirs.

Jan 1, 1954

By Charles Janin, HENNEN JENNINGS

Many articles have been written on the general principles and details of gold dredging, a but it is not possible within the limits of this paper to recapitulate them, and it is thus necessary to assume some knowledge of this literature by the readers of this paper. Although the purpose of this paper is to describe gold dredging in Montana, a brief mention of some early appliances used in New Zealand, Australia, and California may serve as a world-connecting link in our consideration of the development of gold dredging. DREDGES EARLY USED IN NEW ZEALAND, AUSTRALIA, AND CALIFORNIA. Spoon dredges operated by hand were tried in New Zealand on rich spots in the Clutha River with some success as early as 1865. A dredge of this kind is shown in Plate I, A. In 1870 a modification of the spoon, operated by steam and being thus a primitive steamshovel dredge, was worked in New Zealand. Steam-shovel dredging was attempted in California as early as 1888 and 1893, and with some success in later years. The elevator gold dredge with endless bucket chain was put into operation in New Zealand in 1882. Plate I, B, illustrates a type of this dredge operated by current wheels. Plate II, A, shows a steam-operated dredge of this class, also started in 1882. In 1897 R. H. Postlethwaite, connected with the Risdon Iron Works, San Francisco, introduced the dredging practice of New Zealand into California. The first dredge built sank in the turbulent current of the Yuba. The second at Oroville, owned and operated by W. P. Hammon, proved effective and was the start in California of successful gold dredging. Since then the growth of the golddredging industry in California has been so rapid that the gold output from dredges in that State exceeds that of all other States in the Union, and, in fact, of any other country of the world, the value of the gold produced in California by dredging from 1897 to the end of 1914 having been about $71,000,000.

Jan 1, 1916

By J. H. East, R. S. Sanford, W. M. Traver, W. S. Wright

"INTRODUCTION This report describes the results obtained from a diamond-drill exploration project performed by the Bureau of Mines on the nickel deposits of the Yakobi Island, Alaska. The Federal Geological Survey 6/ completed a detailed geologic study and mapped the area during the summer of 1940, and a Bureau of Mines examining engineer 7/ made a preliminary examination of the deposits in June 1941, at which time core drilling was suggested as the logical means of determining the extent and grade of the deposits. Equipment and supplies were unloaded on the beach at Yakobi Island on October 21, 1941. The drills were moved to Bohemia Basin, where actual drilling operations wore begun under the direction of a Bureau of Mines engineer 8/ on November 7, 1941. Two core-drill holes were completed on December 7, 1941. Upon the request of the drilling contractor, operations were recessed owing to severe winter conditions. Work on the project was resumed April 27, 1942, under the direction of another Bureau of Mines engineer 9/ and was completed August 15, 1942. During the 1942 season, 13 core-drill holes were completed, and 10 surface pits and a tunnel were sampled. A total of 5, 191 feet of core-drill hole was drilled in 15 holes during the entire project. The results of drilling and sampling form the basis of this report."

Jan 1, 1948

By Bernard J. Steblay

Two instruments have been constructed that extend microseismic data collection and processing capability for Bureau of Mines research in rock burst, coal bounce and outburst, and roof fall monitoring. The first instrument is a 13-channel tape-triggering system. This system allows better utilization of instrumentation tape recorders by collecting data digitally, turning the tape on only when valid data are present, and increasing the dynamic range of the recorder by using digital data. A digital-to-analog converter is used to provide analog output of the recorded digital data. The instrument records a much larger time slice of transient events than do current commercial devices. The second instrument is a microseismic energy measurement device. This device uses recent developments In integrated circuits to overcome the dynamic range and accuracy limitations of previous instruments. The analog signal is converted to a digital one, and then high-speed multiplication techniques are used to square the amplitude value in real time and integrate it.

Jan 1, 1983

By Alexander May

The U.S. Bureau of Mines conducted studies to determine if phosphate slag stockpiles at Tennessee Valley Authority's National Fertilizer Development Center were hazardous materials. The stockpiles were not hazardous materials as determined by Environmental Protection Agency (EPA) extraction procedure (EP) toxicity test. Radium-226 concentration was 28.7 pCi/g in slag and 2.1 pCi/g in background material. Radium-226 was not leached from the slag. Fluoride concentration was 3.87 pct in slag, 0.18 pct in subsurface material under slag, and 0.08 pct in the background. Slag material permeability was 1.65 x 10-3 cm/s, and subsurface material permeability was 3.24 x 10-6 cm/s. Rain water, trapped in a depression on top of the east slag stockpile, became seepage water at the base of the stockpile. Concentrations of EPA toxic elements in seepage water were much less than concentrations from an EPA EP toxicity test on the slag. Twelve elements-Na, Mg, Ca, Sr, Ba, Cr, Mn, Co, Cu, Cd, AI, and P-had higher concentrations in seepage water than in rain water on top of the slag stockpiles, or in creek water adjacent to stockpile bases, indicating that they were leached from slag stockpiles.

Jan 1, 1990

By S. H. Ash

Probably one of the most significant departures in tunneling practice is the introduction of Diesel locomotives far haulage (Diesel trucks have been used for some time). The fallacy of the belief that they do not generate carbon monoxide or toxic gases and can be used indiscriminately has been proved by the authors through observation for several years of atmospheric conditions surrounding the use of Diesel engines in tunnels. Diesel locomotives haves been introduced in tunnel haulage for reasons other than safety or health. Except to the extent that they replace trolleys, with their danger of causing electrocutions, modern Diesel locomotives do not increase safety Or remove any ordinary hazards to safety or health. In fact, they create such hazards, the extent of which is limited entirely by the carbon monoxide-content level set, method of ventilation, adequacy of the measures.

Jan 1, 1942

By C. J. Wilhelm

The Carthage field, in Pamela County, Tex., is one of the largest gas-condensate in respect to both areal extent and volume of recoverable gas in the United States. The field (shown in fig. 1) is approximately 25 miles long by 20 miles wide on a southwest to northeast axis and includes 306 producing wells as of July 1, 1948. 3 distinct reservoirs in the Rodessa and Sligo formations have been found in the Carthage area the two main producing zones being the Upper and Lower Pettit, less important production being found in the Hill zone. Although a small amount of commercial production has been obtained in the Travis Peak formation, it has not been included in this report. An engineering study has been made by Bureau of Mines engineers, with the ultimate objective of arriving at an estimate of the gas reserves, by application of the data made available by the operators in the Carthage field. During World War II the Bureau of Mines submitted a restricted petroleum-engineering report on the Carthage field to the Petroleum Administration for War, at which time (March 1944) the development consisted of only 19 producing wells, 7 of which were dual completions. Because of the restricted nature of the first report and the limited development at the time of writing, a more complete investigation and subsequent publication was considered advisable. Bureau of Mines engineers have made use of all available records such as electric logs, drilling-time logs, core descriptions and results of core analyses, well-completion records, and production data in developing this report.

Jan 1, 1950

By C. P. Mangelsdorf

When the finely bedded shale frequently encountered over coal seams experiences a separation, the material below the separation must behave like a beam or plate in that it must resist both bending and shear. Be-cause of the weakness in interlaminar shear inherent in such strata, shear deflections that are usually ignored in isotropic beam theory may account for a significant part of the total roof sag. Similarly, when a roof truss is installed in such a roof the upward displacement reducing the sag will have components due to shear as well as bending. Questions asked by mine operators about the installation of roof trusses frequently deal with optimum position, slope, and initial tension of the inclined chords. This Bureau of Mines report examines the effects of those chord parameters on the strain energy of both shear and bending and offers optimum values that will minimize the total strain energy of the immediate roof. Design charts are provided, several design examples are included, and the results are compared with current practice. The effects of in situ stresses are investigated and are shown to be equivalent to an additional load on the beam.

Jan 1, 1988

Under the Bureau of Mines Research Contract Number H0252071, Foundation Sciences, Inc. has compared the relative effectiveness of roof bolts installed at an angle over the rib with that of bolts installed vertically at the rib side, The information gathered during this investigation was sufficient to supply supplementary information on the mechanics of roof support systems and the general acceptability of field instrumentation methods. During the 140 days of field investigation, 235 bolts were installed, 45 inclined and 190 vertical, in two adjacent intersections. Of these 235 bolts, 30 were in-stalled with load cells and 38 were tested for anchor capabilities. In addition to this instrumentation, the deformation of the opening was measured by convergence meter on 9 lines throughout the two testing areas, and a borescope and photo-elastic gauges were utilized to obtain information on the roof action beyond the surface.

Jan 1, 1977

By Terry L. Muldoon

The report describes the development of preliminary requirement specifications for standardized operating controls for roof bolting machines used in underground coal mining. According to recent statistics, roof bolting continues to be one of the most hazardous occupations in underground coal mining. The two principal hazards to the roof bolter operator are the machine itself and roof falls during the bolting cycle. The lack of standardization of machine controls is a major contributor to this hazardous situation. Observations of roof bolting operations and discussions with roof bolter manufacturers coupled with detailed analyses of roof bolter control design specifications were performed during this study. Detailed roof bolter operator task analyses, commonality of control analyses, and classical link analyses were also performed. The results of these analyses were then used to produce preliminary requirement specifications for standardized controls.

Jan 1, 1980

By D. R. Hanson

This Bureau of Mines study examines the acoustic vibrational spectra of rock slabs in the range of 0 to 5,000 Hz. The power spectra of so-called drummy rocks were found to be diagnostically enhanced in the range of 200 to 1,000 Hz. Comparison of the power in this band with that in a band from 3,000 to 3,500 Hz provides a quantitative measure of rock stability. A prototype field instrument was designed, constructed, and field-tested. This battery-powered instrument computes the power contained in the two frequency bands mentioned, compares the magnitude of these two quantities, and displays a number that is related to the detachment of the block tested. Field tests show that this instrument is capable of giving reliable measurements of block stability under conditions of noise and dust that would seriously degrade the accuracy of normal sounding techniques.

Jan 1, 1985

By John A. Johnson

Tests ere conducted at the Mount Weather testing adit of the 57 Bureau of Mines on the effectiveness of spraying water along the outside of the drill steel as compared with standard wet-drilling practice. The spray equipment used in the tests was designed primarily for the control, in quarries, of dust from dry drilling with solid type drill steel. Equipment Spray equipment is made in sizes to fit different drill steel but is alike in design, the only difference being in the diameter of the ring and the number of spray holes. The device is mace of cast steel and has a coating of Stellite on the inside edge that comes in contact with the drill steel. It looks like a garden spray, except that the spray holes point in only one direction.

Jan 1, 1939

By E. F. Ferrell

Electrowon molybdenum powders and a commercial hydrogen-reduced powder, all with different minor impurities, were investigated by the Bureau of Mines with respect to inherent properties, to fabrication techniques, and to proper-ties of the fabricated sheet. Compared with the commercial hydrogen-reduced powder, the electrowon powders had a larger particle size, a greater flow rate, a higher apparent density, and a lower oxygen content. Sheet materials prepared from the two types of powders showed similar mechanical properties, under the same conditions of heat treatments, except for low-temperature ductility. Yield strengths varied with carbon content, heat treatment, and test temperature.

Jan 1, 1970

By J. C. Barrett

Bureau of Mines research on the arc welding characteristics of titanium was initiated in 1948. Little was known about the art except that the easily contaminated metal required more protection from the atmosphere during welding than most other metals. Chambers were designed and built within which titanium could be welded with adequate inert gas protection. Welds were made and their properties studied, and prototype items were made successfully. This report, presenting a resume of the titanium arc-welding experiments undertaken by the Bureau of Mines, demonstrates that the process is successful if conducted under proper conditions and describes the welding of prototypes. INTRODUCTION The Bureau of Mines' first report on methods of joining titanium covered the subject of spot welding,4/ outlining the conditions necessary for producing spot welds in ductile titanium consolidated by powder metallurgy methods and describing the characteristics of such welds. This report embraces the field of fusion weld-ing of titanium and traces the development of suitable methods and equipment for producing such welds.

Jan 1, 1956