Search Documents

By Karl-Heinz Frohne

This report presents the findings of a study of a portion of the Clover-Rush Run oilfield located in Roane County, W. Va. The study was made to investigate the possibilities of secondary oil recovery in the Big Injun sandstone underlying the William Kaufman lease. Reservoir properties, original reserves, and primary oil recovery are also presented. The investigation is based on a core analysis and related laboratory tests, well records, field production data, and subsurface information from the Kaufman property. A theoretical primary oil recovery of 9.7 percent of original oil in place is predicted for the reservoir. A waterflood performance prediction of a hypothetical pilot area was made by use of a computer. The prediction showed that, based on laboratory oil water relative permeability curves, the water-injection time needed to initiate oil production is excessive and that the stabilized water-injection and corresponding oil-production rates are very low. This precludes waterflooding the reservoir on an economic basis. A prediction for secondary oil recovery by gas injection was attempted but could not be completed because essential reservoir data were not available. In July 1965, the lease operator initiated, and is currently conducting, a gas-injection program, but there had been no increase in oil production up to November 1966.

Jan 1, 1967

By Susan M. White

Increased coal production, wider use of indiscriminate mining techniques, improved cleaning methods, and greater emphasis on clean fuels is increasing the rate at which wastes accumulate Over the next several years, Colorado Plateau underground coal production is predicted to increase. Currently, mine refuse is deposited in canyons or lowland areas near mines. This study presents information on the nature of coal refuse and disposal practices on the Colorado Plateau. Samples were collected and analyzed to provide information to help formulate alternative methods for reclaiming refuse piles. The analyses were based on determining the capability of unmodified refuse to provide a suitable medium for plant growth. Local topsoils which would be used in reclamation were used as standards. Potential environmental hazards were assessed also. A general cost analysis was done for both surface and underground disposal and the advantages and disadvantages of each were assessed. Several problems were identified which, if solved, would increase the effectiveness of state regulatory programs.

Jan 1, 1982

By Joseph Coffman

There are 14 operations that supply 97% of the Market Economy Country (MEC) manganese and contain nearly all of its resources. Six mines account for about 70% of the production and 85% of the resources; there are no known resources that are economically close to those that are currently being mined. Costs (January 1989 dollars) of producing manganese concentrates from the operations evaluated are estimated to range from $ 0.96 to $ 1.86 per long ton unit (ltu or 22.4 lb) of contained manganese. Total MEC demonstrated resources evaluated amount to about 1.2 billion tons of in situ ore containing 474 million tons of manganese. Identified resources amount to about 1.8 billion tons of in situ material. Key results of the study indicate the following: 1. The MEC supply of manganese will be from the currently mined resources well into the next century. 2. Centrally Planned Economy Countries (CPEC's) will be increasingly dependent on MEC manganese ore and concentrate in the future. 3. At the 1976 to 1987 demand increase rate, total MEC resource needed through the year 2000 would be about 282 million tons of in situ material. 4. Transportation and infrastructure support will continue to be major elements of production costs.

Jan 1, 1992

By W. H. Strickland

Ultrasonic ranging sensors are inexpensive, have no moving parts, have no lenses to clean, are normally small and unobtrusive, and can measure distances through moderate amounts of dust, smoke, and humidity, so they are well suited to underground mines. In the work reported here, conducted by the U.S. Bureau of Mines, researchers tested ultrasonic ranging sensors for their ability to define rib line features for computer-aided navigation of underground mine mobile equipment. The investigation began with laboratory tests of field of view, angle of incidence, intersensor variation, and ranging accuracy of the individual rangers in a ring array produced by Denning Robotics of Wilmington, MA, The results showed that the sensors have good accuracy and low variability. Additional experiments at AMAX'S Henderson Mine showed the sensors could accurately and reliably measure the distance to mine features, including convex and concave corners and rib intersections. The results showed that when used properly, the ranger data are accurate enough for reliable mine vehicle navigation. When used incorrectly, ultrasonic rangers do not provide the anticipated data. Therefore, this report explains the principles of ultrasonic range measurement, describes the ranger's strengths and weaknesses, and explains proper ranger use and data analysis.

Jan 1, 2010

By L. A. Haas

The Bureau of Mines conducted bench-scale leaching tests with recycled spent copper electrolytes and copper-nickel mattes produced from the Minnesota Duluth Complex concentrates. This report describes the first stage of an overall two-stage leach operation. The objective of this research was to determine the matte-leach technology required to convert spent copper electrolyte into an enriched nickel liquor suitable for a nickel refinery and there-fore essentially free of copper, iron, and sulfuric acid. The experimental variables investigated were matte composition, particle size, spent electrolyte content, pulp concentration, oxygenation, temperature, and time. The time required to produce an enriched purified nickel liquor decreased with increasing pulp concentration, temperature, and oxygenation, but increased with increasing particle size and electrolyte copper and acid content. Nickel-rich (about 50 g/l) liquors at a pH of about 4 and containing less than 1 g/l of copper and iron were produced at 70° C by leaching minus 325-mesh low-iron (less than 5 pct) matte for 8 hours with spent electrolyte containing 22.4 g/l Cu, 28.9 g/l Ni, less than 0.1 g/l Fe, and 50 g/l H2S04 at a pulp concentration of 1 kg of matte per liter of spent electrolyteo Varying the nickel content of the spent electrolyte from 11 to 101 g/l appeared to have no appreciable influence on the matte leaching characteristics.

Jan 1, 1981

By John J. Sammarco

The U.S. Bureau of Mines is conducting research into computer-assisted mining, which requires investigation of new techniques for development and application of computer-based technologies. Today's technology can require significant effort in software development, as has become evident in the early stages of this Bureau research. Technologies for software automation, such as computer-aided software engineering (CASE), are available. This report explores CASE, its general features, and its importance in software development. Information is presented to assist in selection and application of the variety of CASE tools and methods for automating various stages of software development. When evaluating CASE for use, it is important to examine tools that support an organization's existing methods of software development. Support for existing hardware platforms must also be examined. Merely selecting a "good" CASE tool does not insure success. Thorough evaluation of implementing CASE is also critical. Subjects to evaluate for CASE implementation include organization culture, support from management and end users, training resources, and pilot projects. Organizations that benefit the most from CASE evaluate CASE features with respect to their needs and they properly implement CASE.

Jan 1, 1990

By F. A. Rutledge

"The W. E. Dunkle mine, sometimes called the Costello Creek coal mine, is 8 miles N. 20° W. of Colorado Station on the Alaska Railroad. The presence of coal in this area has been known since the district was extensively pros¬pected for gold between 1911 and 1915. At that time, coal from this deposit was used by miners for blacksmithing. The increased demand for coal resulting from government defense projects in Alaska led to exploitation of this deposit in 1941.The inability of Alaska coal mines to supply the quantity of coal required by public and private consumers and by the armed forces in Alaska was responsible for establishment by the Army of the Coal Procurement Section of its Alaska Department. It proposed to investigate the deposits and to expedite production from the Alaskan coal fields. The Bureau of Mines closely cooperated in this program.The quality of the Dunkle coal and the favorable location of the deposit caused it to be one of the properties chosen for investigation under a joint Army-Bureau of Mines-Geological Survey program.During July 1943, the coal area in the immediate vicinity of Costello Creek was geologically and topographically mapped. by Clyde Wahrhaftig and Jacob Freedman, geologists, U. S. Geological Survey. F. A. Rutledge, mining engineer of the Bureau of Mines examined the property July 18 to 22, 1943, and a project of trenching, diamond drilling, and sampling was initiated on August 4, 1943. During the project Clyde Wahrhaftig remained at the Dunkle mine to interprets drill cores and assist the author in planning the explora¬tory program. The project was completed October 7, 1943.Field investigations were under the general direction of R. S. Sanford, acting chief, Alaska Branch, Mining Division. Coal analyses were made by Maurice L. Sharp, coal analyst for the Alaska Railroad.Special mention is made of the cooperation and assistance received from Clyde Wahrhaftig, geologist, U. S. Geological Survey.The many courtesies received from the owner, W. E. Dunkle, and the members of the Army Coal Procurement Section, Alaska. Department, also are acknowledged.The W. E. Dunkle coal mine is in the Broad Pass region on the south slope of the Alaska Range at an altitude of 2,800 feet (fig. 1). It is situated within the Third Judicial Division, headquarters of which is Valdez, Alaska. The area is situated approximately at latitude 63° 15' N. and longitude 149° 30' W. and is connected with the Alaska Railroad at Colorado Station by an 11-mile gravel road that is passable throughout the year. This road is maintained by the Alaska Road Commission. A private telephone line to Colorado Station connects with the telephone and telegraph service of the Alaskan Railroad.The passenger rate from Anchorage, Alaska, to Colorado station is $12.10. Freight rates are $1.60 a hundred pounds for heavy machinery and $2.66 a hundred pounds for first-class freight.The Costello Creek coal basin is in an area of low relief and has been dissected by numerous creeks flowing down the south flank of the Alaska Range. The Dunkle coal mine is on Coal Creek, a small tributary of Camp Creek, 1,000 feet from their junction. About 700 feet below this junction, Camp Creek joins Costello Creek, which in turn empties into Bull River 1/2 mile above the latter's confluence with the West Fork of the Chulitna River. The location of the mine is shown on figure 1."

Oct 1, 1948

By A. B. Hooker, J. W. Paul

"There was a time when any suggestion that the Davy flame (safety) lamp be discarded, would have evoked unlimited, criticism. However, that time is past.Investigations both here and abroad have shown conclusively that the Davy lamp does not have the necessary factor of safety against ignitions of mine gas, and England, the lost stronghold of the Davy lamp in Europe, has eliminated this lamp and substituted safer types.In the United States there are companies who still use the Davy lamp in spite of all that has been said and published as to the dangers connected with its use.Recently the purchasing agent of an anthracite coal company requested the Department of the Interior, Bureau of Mines, to pass upon the safety of some braise gauzes for use in a shielded Davy lamp. A shielded Davy lamp is an ordinary Davy safety lamp equipped with a circular brass shield that is attached to the lamp posts. This shield extends about one-half way around the gauze and one-half of the gauze height. The main purpose of the shield is to prevent the lamps being extinguished by a sudden increase in the velocity of the air current past the lamp.The brass gauzes submitted for this test represented two grades of brass - a yellow brass and a red brass. The analysis of these brasses was not determined. Two shielded Davy lamps that were submitted for the tests each had a steel gauze. These steel gauzes were also tested. Tests were made in horizontally moving mixtures of Pittsburgh natural gas and air at velocities of 400 to 1,000 feet per minute. The gas percentages used were 7%, 8.6%, and 11%. Tests were made with the lamp shield in two positions relative to the lamp and direction of flow of the gas-and-air mixture. In one position the shield was between the gauze and flow, as normally used. In the other position the shield was on the downstream side of the lamp. The tests were continued until one or more failures or gas explosions been obtained with each of the six gauzes. The results of these tests summarized as follows:"

Jun 1, 1923

By W. E. Pittman

The Bureau of Mines, as part of its Health and Safety Technology Program, is conducting research on the use of ground penetrating radar (GPR) for mine hazard detection. GPR offers a possibility of mapping immediate below-surface geologic conditions, including faulting and other anomalies, thereby exposing potential safety hazards to miners. This report summarizes a literature review of the current status of GPR research in and outside the Bureau.

Jan 1, 1984

By R. G. Meara, O&apos

[P.F? bmit e-ninirq ir.3.l r;tq: in the Znited State :; was u~irlyortant p~ior to the Torld ;Jar, ?-.lt with the c~r,sxti~rl of imports d11rln.c thr World 'Jar tke Rmericnn mar~factu~er:. of 1itkopone mcl Sayiun c;~oai?als forced tile tl~veloor?.ent of domertic bar,i$e dqosit9. Pr%~~,n-ily bcca-lse of tho increasing dc.n;;nl'i for lit,hupone3 by the pr?i:~t, Tlocr-covcrin~;, ,md rt1tbe.r indl~stries, ~3c.vs1o~:rnc2t of cto~entic de~onits has cr~ntim~ed to c-cpand. 13 1914, the salnr! oC doxegtic c~l~.dt? t,m-it~ ;u~cr-~nteii. to 52,91? tons, in 1237 ???,1!.1 tons nmre so1.d; thc 12:t~r rcyrprcntcd 77 .E;T pmccnt of the tot,:rl, dr??;ectic and imortcd., haritd US~C in the Cnited State? di7rinz t,hat :.vXr. C,f +he total 193,3:& ton? coy.1~-ed in the United 4 Steter ir. 135, 3E.X percent v;as usec? as groi.z.ld ~rai.te? , "0.3 percent arr lithopone, and 17 .:A ].ercc?t in the rnx 11fact,ure of b;~riim chs:nicals ]

Jan 1, 1938

By R. G. Meara, O&apos

[P.F? bmit e-ninirq ir.3.l r;tq: in the Znited State :; was u~irlyortant p~ior to the Torld ;Jar, ?-.lt with the c~r,sxti~rl of imports d11rln.c thr World 'Jar tke Rmericnn mar~factu~er:. of 1itkopone mcl Sayiun c;~oai?als forced tile tl~veloor?.ent of domertic bar,i$e dqosit9. Pr%~~,n-ily bcca-lse of tho increasing dc.n;;nl'i for lit,hupone3 by the pr?i:~t, Tlocr-covcrin~;, ,md rt1tbe.r indl~stries, ~3c.vs1o~:rnc2t of cto~entic de~onits has cr~ntim~ed to c-cpand. 13 1914, the salnr! oC doxegtic c~l~.dt? t,m-it~ ;u~cr-~nteii. to 52,91? tons, in 1237 ???,1!.1 tons nmre so1.d; thc 12:t~r rcyrprcntcd 77 .E;T pmccnt of the tot,:rl, dr??;ectic and imortcd., haritd US~C in the Cnited State? di7rinz t,hat :.vXr. C,f +he total 193,3:& ton? coy.1~-ed in the United 4 Steter ir. 135, 3E.X percent v;as usec? as groi.z.ld ~rai.te? , "0.3 percent arr lithopone, and 17 .:A ].ercc?t in the rnx 11fact,ure of b;~riim chs:nicals . ]

Jan 1, 1938

By Jeffrey Shawn Peterson

The testing procedures of the u.s. Mine Safety and Health Administration specify that intrinsic safety acceptance tests be conducted using a standard tungsten-cadmium electrode configuration in the break-flash apparatus. However, in realistic mining environments, other materials may be more likely sources of sparking. Information defining the probability of spark ignition between common materials such as aluminum, brass, copper, lead, tin, cold-rolled steel, and stainless steel is of more practical value in determining ignition hazards. The U.S. Bureau of Mines has completed an investigation of the influence of material on the ignition probability using the breakflash apparatus. By comparing ignition currents or ignition voltages corresponding to a probability of one ignition per thousand sparks to those found previously for cadmium, a margin of safety may be estimated for each material. This report presents the results of an investigation into the influence of disk electrode material on the probability of ignition.

Jan 1, 2010

By Henry P. Cole

A comprehensive review of published research was carried out to identify methods for teaching and assessing critical but nonroutine skills needed for coping with emergency situations. Specific methods for assessing critical skills proficiency in aviation, medicine, organization management, the military, and other industrial/technical workplaces are described. The potential application of these methods for teaching and assessing (1) critical first aid and (2) self-rescue and escape skills to underground coal miners in annual refresher training is explored. Research and development activities that may improve mine health and safety training are suggested. Most of these research and development activities were completed later in the project. This additional work is reported in the project technical report #2 and the final report. The research reported in the present document was completed in 1984 -85. Many of the initial findings reported in this document are updated in the later project final report.

Jan 1, 1988

By Allan J. Clark

This paper, describing the milling practice of the Homestake Mining Co., is one of a series being prepared by the Bureau of Mines. The author acknowledges the assistance of T. G. Chapman, one of the consulting engineers of the Bureau of Mines, in arranging this paper for publication.

Jan 1, 1931

By Robert Lee Stahl

Comprehensive field tests were made by the Federal Bureau of Hines at the Conda open pit mine near Soda Springs, Idaho, to determine whether surface geophysical techniques could be used to detect and delineate faults in phosphate deposits. The tests included seismic refraction, magnetometry, electrical resistivity, and airborne photography. Of the several geophysical techniques tested in the field, horizontal resistivity profiling was the most effective method for diagnosing faults. The method is quick, inexpensive, accurate, and can be easily used by mining company personnel to detect and delineate faults.

Jan 1, 1975

By Lindsay D. Norman

Eleven major pyrometallurgical processes and operations suggested for recovering manganese from domestic resources are described. These include seven pyrometallurgical processes that usually yield a ferroalloy or a product from which ferromanganese can be produced in one operation. The remaining four involve pyrometallurgical operations whose products require either an additional two-stage process to produce ferromanganese or chemical processing to recover a high-quality manganese oxide product.

Jan 1, 1962

By R. V. Higgins

In a recent report3/ the authors presented a rapid method of calculating, by means of a desk calculator, the future performance of oil reservoirs in which the motivating agent was gas. The accuracy of the method was tested by data obtained from an electronic computer. Because of the accuracy obtained for the limited number of calculations performed, considerable interest has been expressed in the electronic computer program used to obtain the comparative data by an analytical solution. Accordingly, the computer procedures for the analytical solution are presented in this report. In an earlier report, 4/ a reservoir appraisal procedure was published in which an iterative method was used. Many requests were received for the computer program used to obtain the values given in that paper. That program, with some modifications, also is presented in this report. The modifications are given because of the progress that his been made in computers, and because much of the program for the analytical solution is usable for the iterative procedure.

Jan 1, 1960

By Erich K. Bender

This report summarizes work performed under Phase I of USBM Contract No. H0366024, Noise Reduction of Jumbo Mounted Percussive Drills. Four drills -Gardner-Denver D93LAR and DH123 and Ingersoll-Rand 0475 and VL120 models were measured at the two manufacturers? test sites; data are given in terms of characteristic noise and vibration levels. A survey of percussive rock drill users is reported. The rationale for the choice of a demonstration drill, the Gardner-Denver DH123, is given and a desired noise reduction goal is established.

Jan 1, 1976

By P. A. Wasson

The investigation described in this publication was conducted by the Bureau of Mines to determine the effectiveness of the anionic silica flotation method on goethitic iron-bearing materials from the Cuyuna Range, Minn. Samples used in this investigation were a composite of drill core from 13 holes, and 3 samples from lean ore stockpiles. These samples are believed to be typical of the mineralization occurring in an area with a potential reserve of several million tans of submarginal iron ore. Results from batch tests showed that the iron-bearing minerals could be effectively concentrated by flotation removal of the siliceous gangue. The drill hole composite yielded laboratory flotation concentrates from locked tests containing 56.8 percent Fe and 6.1 percent silica, with an accompanying iron unit recovery of 94.2 percent. Concentrates containing 52.4 to 53.7 percent Fe also were produced from the lean ore stockpile materials; corresponging iron recoveries ranged from 71 to 79 percent in the batch tests, with the possibility remaining for additional recovery of iron from the middlings.

Jan 1, 1963

By William H. Waggaman

The United States not only is the largest producer of phosphate rock but also manufactures and consumes greater quantities of phosphate products than any other country. New and expanding uses will increase even further the demand for this basic raw material. Only a small proportion of the total quantity of phosphate rock mined and marketed is consumed directly in a raw or unprocessed state; the vast bulk is chemically treated and converted into [ertilizer] and a wide variety of finished products that play a vital role in [r] national economy. Three fundamental methods are employed in decomposing phosphate rock. 1. Reduction by carbon at high temperatures. 2. Treatment with one or more acids. 3. Calcination or fusion with silica, sodium salts, magnesium minerals, or small quantities of phosphoric acid.

Jan 1, 1960