Search Documents

By O. C. Blade

"INTRODUCTION This report on the properties of motor fuels sold through service stations in the United States is a continuation of a series of reports made in accordance with a cooperative agreement between the Coordinating Fuel Research (CFR) Committee of the Coordinating Research Council (CRC) 3/ and the Bureau of Mines of the United States Department of the Interior. The first of these reports presented data on motor gasolines sold during the winter of 1935-36.4/ Further reports were issued describing motor gasolines sold during the succeeding sum¬mers and winters to and including the summer of 1941.4/ No reports were made on motor gasolines sold during the winter of 1941-42 and during the summer of 1942. However, starting with the winter of 1942-43, the semiannual reports were resumed.!The present report presents analytical data for 4,544 samples, represent¬ing the products of 124 companies. The samples represented in this report were obtained during December 19146, January and February 19-(. As in previous surveys, the companies covered Ly the survey include both large and small suppliers. Conforming to former reports, the data cover three groups of samples - regular-price, premium-price, and third-grade gasolines.As the number of analyses submitted for samples of third-grade gasoline are not considered adequate to represent this type of motor fuel, data for the analyses have not been averaged, but the individual items are tabulated. The number of samples, items, and brands comprising each group is as follows: Regular-price, 2,368 samples, 319 items, and 113 brands; premium-price, 2,172 samples, 289 items, and 106 brands; third-grade, 4 samples, 4 items, and 4 brands. The meanings of these terms as used in the surveys are as follows:"

Aug 1, 1947

By J. A. Organiscak

The U.S. Bureau of Mines investigated the relationship of bituminous coal seam parameters and the amount of airborne respirable dust generated at longwalls. Dust and coal samples were obtained from 20 longwalls operating in geographically representative coalfields throughout the United States. Statistical analyses of coal seam parameters and airborne respirable dust measurements indicate a likely causal relationship between seam type and respirable dust. Low-ash, high-volatile coal seams were associated with higher airborne respirable dust levels. A negative linear correlation (significant at the 95-pct confidence level) was observed between the seam's ash content and airborne respirable dust, explaining up to 18 pct (R2 = 0.18) of headgate dust level variation and up to 15 pct of tailgate dust level variation. Volatile matter was found to have a positive linear correlation with tailgate dust level, explaining 16 pct of the variation. Further data examination indicates that these relationships with dust are most likely nonlinear, because of improved R2 values over the linear correlations. However, a notable portion of longwall dust production is influenced by other operational parameters, so additional research under more controlled conditions is needed to determine the seam's causative functions.

Jan 1, 2010

This Bureau of Mines report is devoted to descriptions of systems that provide in-mine wired telephone service. Although they may incorporate other features, each system described functions to allow one telephone to selectively access another telephone. Except for the paper on Conventional Telephone Equipment, the equipment described is newly developed and specifically designed to satisfy the requirements of underground mine communications.

Jan 1, 1977

By R. S. Dean

The function of the Metallurgical Division is to conduct investigations relating to the treatment of mineral products from the state in which they are mined to the refined metal or other unfabricated product. These investigations include scientific and practical studies of ore dressing, covering the crushing and grinding of ores, separation by gravity, flotation. and magnetic methods; the hydrometallurgical treatment of ores, including cyanidation and amalgamation of the precious metals; the smelting and refining of copper, lead, and zinc, as well as the rare metals; and steel-melting practices from the raw ore to the finished steel. The object of this work is to conserve natural resources and eliminate waste by furnishing information on current methods of metallurgical practice. making fundamental studies of metallurgical processes, and developing new processes to the point of demonstrating their practicability. The Division is made up of sections devoted to the several phases of this work, each section being headed by an investigator capable of supervising his particular work. The work is carried on at the experiment stations and field offices or in the field, whichever seems best suited for the work in hand. The following, projects should be mentioned as particularly outstanding among those consummated successfully during the year: 1. Application of the type of chemicals known in the textile industry as wetting-out agents to flotation and agglomeration of ores, particulary soluble salts such as sodium and potassium chloride which must be treated in saturated brine. 2. Demonstration or a linear relation between surface and coercive force in magnetic minerals and Its application to magnetic separation and to the determination of grinding efficiencies and other metallurgical data which require surface determination at very fine sizes. 3. Pilot-plant demonstration of the practicability of the reduction of iron ore by natural gas and conversion of this direct iron into steel by direct melting and by forging and rolling before melting. The structure and properties of the iron so produced were studied in detail. This report covers the fiscal year July 1. 1934, to June 30, 1935.

Jan 1, 1936

By Lloyd Williams, H. K. Gibbs, William L. Crentz, J. W. Miller

"Reserves This investigation shows that the Poplar Creek is the most important bed in Scott County from a production standpoint. Although the Poplar Creek bed contains the largest reserve, the Big Mary has a larger recoverable reserve. Estimates of reserves also have been made for the Pewee, Red Ash, Windrock, Upper Pioneer, Jellico, and White Oak beds.Known measured and indicated reserves of coal, based on a minimum bed thickness of 14 inches and on 1,800 short tons per acre-foot of coal in place, are estimated to be 143 million tons as of January 1, 1954. Of this total, 74 million tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.Recoverable reserves of coal are estimated in beds 28 inches and more thick. This thickness is about the minimum now being mined by hand loading onto conveyors in the Appalachian region. The weighted average recovery for all beds in Scott County, as determined by this investigation, is 52.4 percent. This percentage is based on the total thickness of coal in the bed (less partings three-eighths inch or more thick) rather than on the thickness of the coal mined. Based on the weighted average percentage of recovery for all beds in Scott County, the recoverable reserves of coal are estimated to be 39 million tons as of January 1, 1954.Coal Analyses Chemical analyses of coal samples taken for this study show that the coal in Scott County is of high-volatile a bituminous rank except the Upper Pioneer bed, which is shown to be high-volatile B bituminous. The Pewee bed shows typical low-sulfur characteristics. The high ash and sulfur in the Big Mary are characteristic of that bed. The Poplar Creek is moderately low in ash and sulfur in areas where there is no parting in the bed."

Jun 1, 1956

By G. E. McElroy

When mechanical ventilation is to supersede the natural ventilation of a mine it is desirable to determine what resistance the mine as a whole offers to the flow of air in order to specify properly the limiting duties of a ventilating fan. The relation of pressure to volume of flow for the mine as a whole may be calculated from experimental data, or it may be determined directly by measurements of volume of flow and the natural draft pressures causing flow; but in both methods the determinations are affected by many variables. With the intention of making a practical application of both methods, a small metal mine in process of development at Butte, Mont., was selected by the writers as the object of experiments planned to compare the mine resistances determined by measurements of natural draft and volume of flow with those calculated from experimental data. Four sets of teats were made with natural draft in October, 1925, December, 1925, April, .1926, and September to December, 1926; the last set consisted of a series of weekly observations. DESCRIPTION OF MINE The mine selected for the experiments was a typical vertical shaft metal mine in the development stage. No stoping had been done, and ventilation was confined to shafts, crosscuts, drifts, and raises. Figure 1 is a dia¬grammatic sketch of the main openings. All were timbered with full sets on approximately 5-foot centers. The shaft compartments were 4 by 4.5 feet, and one in each shaft was partly blocked by staggered manway landings. A pump column in the upcast shaft was discharging about 280 gallons a minute of water at 70° F. from the 1,000-foot level. The drifts were slightly sinuous, but the crosscuts were exceptionally straight and uniform in area; both drifts and crosscuts were about 5 by 7 feet in cross section. The raises were composed of vertical sections joined by frequent 450 offsets; each had three 4.5 by 4.5-foot compartments, of which two were plank-lined ore chutes and one was partly

Jan 1, 1928

By C. M. Frost

Two Federal Bureau of Mines recycle hydrogenation experiments to prepare catalytic cracking feed stock were made at 3,000 pounds pressure with crude shale oil retorted from Green River (Colo.) shale in the gas-combustion retort. The hydrogenated product from the first experiment, made at 784° F., was used for investigating the effects of nitrogen content on catalytic cracking yields and for determining the quality of the catalytically cracked gasoline. Hydrogenated product containing 0.14 percent or more of nitrogen produced less gasoline when cracked in a CAT "A" unit than was obtained from East Texas light gas oil cracked at the same conditions; product containing 0.10 percent or less nitrogen produced a quantity of cracked gasoline equal to that obtained from the East Texas light gas oil. The catalytically cracked gasoline had research octane numbers calculated to be approximately 95 clear and 103 with 3 ml. of tetraethyl lead. The principal product from the second experiment, made at 828° F., was a low nitrogen content gas oil which was used for investigating the yields of cracked products obtained when it was catalytically cracked to different degrees of conversion. Yields of cracked products, when plotted as functions of conversion, were essentially the same, within the experimental range of the data, as published yields from catalytic cracking of East Texas heavy gas oil; however, yields from cracking the shale-oil product did not display the sensitivity to change of cracking temperature that has been found for East Texas gas oil.

Jan 1, 1960

By Lowell L. Patten

The Federal Bureau of Mines participated with the National Aeronautics and Space Administration and Martin Marietta Aerospace in developing, building, and testing a portable X-ray fluorescence spectrometer for use as an analyzer in mineral-resource investigative work. The prototype battery-powered spectrometer, measuring I1 by 12 by 5 inches and weighing only about 15 pounds, was designed specifically for field use. The spectrometer has two gas-proportional counters and two radioactive sources, 109Cd and 55Fe. Preliminary field and laboratory tests on rock specimens and rock pulps have demonstrated the capability of the spectrometer to detect 33 elements, to date. Characteristics of the system present some limitations, however, and further improvements are recommended.

Jan 1, 1982

By Maurice Deul

A special short-term research project was initiated to develop plant design parameters for treating mine waters to yield an effluent acceptable for discharge into streams and a sludge amenable to effective and economic disposal. Neutralization was investigated to provide simple and direct treatment of ferruginous acid waters using lime; coarse limestone, and limestone followed by lime. Limestone treatment was accomplished using a small cement mixer as a simple reactor to provide abrasive agitation of limestone and mine water. Results from tests with nine mine waters encompassing a wide range of iron and acid concentrations showed that coarse limestone, one of the cheapest neutralizing agents known, is potentially useful for treating mine water discharges. However, process variables must be defined more completely before the practical applications and limitations of the process can be fully established. In all the tests a pH of >7.2 was obtained ultimately with limestone. Reaction time to reduce the iron content below 7 ppm in the water was dependent on the original ferrous iron concentration. For waters with high ferrous iron content, treatment with limestone followed by lime rapidly produced an acceptable treated water, Sludges with good settling and handling characteristics resulted when limestone was used for neutralization either alone or with subsequent treatment. Reaction rates are expressed graphically as pH change and iron depletion curves; characteristic solids settling curves are shown. The temperature dependency of ferrous iron oxidation was verified.

Jan 1, 1967

By E. E. Creitz

Application of the usual chemical methods to the determination of beryllium in the mineral-dressing products of a spodumene pegmatite was found to be unsatisfactory as to speed, accuracy, sensitivity, and range of analysis. A spectrographic method is described for the determination of beryllium. Samples are ground, mixed with borax, high-purity, flake graphite, and an internal standard; then they are fused, reground, pelletized, and excited with a high-voltage-spark discharge. Investigation of several spectrographic techniques to overcome matrix effects are described. The method developed gives results for beryllium in the concentration range from 0.002 to 5.0 percent; the average probable error of duplicate determinations was below 3.0 percent of the quantity present. INTRODUCTION The main source of beryllium in pegmatite is the mineral, beryl. Many of the conventional methods for the determination of beryllium in beryl are not suitable for control purposes because of lack of speed and accuracy, especially in the range below a few tenths percent. Beryl resists the usual chemical attack and can be lost in a hurried chemical analysis.

Jan 1, 1958

By G. W. Weems

The specific objective of this investigation was to determine the compressibility factors for helium and carbon dioxide mixtures at -10° and -20° C and pressures to 1,000 psia. A Burnett apparatus was used. Data from the experiments were treated by the method of Barieau and Dalton. Tables of compressibility factors and approximations of the virial coefficients are presented for 10 binary mixtures as well as for helium and carbon dioxide. The results follow the same trend as data previously reported.

Jan 1, 1970

By W. J. Kroll

Despite the fact that barium minerals are plentiful and widely distributed in nature, this element is one that we do not yet know how to prepare cheaply in metallic form. This is due to its chemical activity, as evidenced by its great affinity for fluorine, chlorine, oxygen, nitrogen, hydrogen, and sulfur. Furthermore, it forms a very stable subchloride and subfluoride, which prevents isolation of the metal by fusion electrolysis from a halide bath. A good survey of the metallurgy of barium calcium, arid strontium has been made recently in Light Metals (54,55).3/ Metallic magnesium (46), calcium (83), barium, and strontium (27) reduce each other's oxides. Proof of this can be found in the activation of BaO after reduction with Mg, which leads to the formation of so-called "Maquenne" mixtures (58) used for absorbing gases. However, it is impossible to extract the reduced metal- from the residue, a fact that Guntz (25) attributed to the formation of barium suboxide. There is no necessity for presuming the formation of such a compound, as it has boon established that in the reduction there is always formed an alloy of the alkaline-earth metal with the magnesium, which is capable of producing hydrogen when brought into contact with water. The reduction of alkaline earth-metal oxides with aluminum was observed by Mallet (57) in 1877, but recent investigations have shown that the end product of the reaction is an alloy of aluminum with the alkaline earth metal (1,2). Silicon also has been suggested as a reducing agent, and the results obtained are the same (84,85).

Jan 1, 1945

By D. E. Wolfson

As a part of its overall program of coal carbonization, the Bureau of Mines is studying the coking properties of coals that may be used for metallurgical purposes. The objectives of this study were given in detail in a previous report The inherent suitability of coal for metallurgical purposes depends primarily on (1) chemical composition, (2) preparation characteristics, and (3) carbonization behavior. The first two factors, Be well as the amount of available reserves, are considered in selecting coals for carbonization tests. The selection of coal beds in Harlan County, Ky., for coking tests was based, in part, on recent studies of coal reserves by Wallace,3/ who estimated the recoverable reserves in beds 28 inches or more thick, in tons, as follows:

Jan 1, 1956

By M. R. Geer, H. F. Yancey

"INTRODUCTION Throughout the history of coal washing, the jig has been one of the most important coal-cleaning appliances. In 1935 34.7 percent of the 45,361,021 tons of clean coal produced was the product of jigging. 4/ Previous to 1928, most of the jigs used in the United States were of the piston type, with which sufficient mobility to allow stratification in bed is imparted by the reciprocating up-and-down movement of a piston in the water compartment adjacent to the screen compartment. In 1928, the Baum type of jig was introduces in this country and has since come into wide spread use. In this type, water pulsations are imparted by application and release of compressed air to the water compartment. All prior studies of the mechanism of seperating cleared coal from impurity by piston-type jigs. 5/ The same laws of settling, of course, apply to both types, piston or Baum, but the character of the separation with the Baum type may be modified more easily because of the flexibility with which air may be handled, as distinguished from the fixed action of eccentrics commonly used in piston jigs. Since no detailed studies are available to show the performance, that is, the character of the separation between coal and impurity, of the Baum type the Bureau of Mines undertook the investigation recorded in this report."

Jan 1, 1938

By Howard P. Hamlin, John W. Sweeney

Shales , clays , and loess in Iowa were tested and evaluated to determine feasibility of producing lightweight aggregate by commercial rotary - kiln or sintering methods . Preliminary testing was conducted in a muffle furnace . Rotary - kiln tests were conducted in a 16 - inch by 14 - foot rotary kiln . Concrete cylinders and cubes were tested to determine qualities of the aggregate . Three samples made suitable lightweight aggregate by rotary - kiln methods and two by sintering .

Jan 1, 1964

By F. E. Brantley, D. A. Martin

Synthetic zeolites were tried as selective adsorbents for recovering sulfur dioxide from synthetic gases and gases produced from gypsum decomposition . Initial adsorption tests , using the synthetic gases , indicated that three of these compounds , having sulfur dioxide capacities of up to 29 grams per 100 grams of adsorbent , were satisfactory . Regeneration studies showed that over 90 pct of the sulfur dioxide desorbed from the loaded beds was of sufficient purity for direct liquefaction . However , all zeolites tested lost adsorptive capacity with repeated use . The zeolite determined to be the most promising in the preliminary synthetic gas tests was also evaluated for capability in adsorbing sulfur dioxide from gases produced by the thermal decomposition of gypsum . Despite small amounts of hydrogen sulfide in the gypsum decomposition offgas , good adsorption of sulfur dioxide was attained . The economic practicality of utilizing zeolites for sulfur dioxide removal from industrial gases was not evaluated , but the technical feasibility was demonstrated .

Jan 1, 1963

By D. E. Redmon

Exploration of hidden mineral deposits becomes increasingly important as known ore reserves are depleted. The primary objective in any exploratory program is to obtain enough reliable information to evaluate accurately the potential of the mineral deposit. Constant improvement in equipment and technique has established drilling as one of the most valuable methods of exploration. This paper presents the results of studies of several drilling methods currently used in the search for uranium deposits in sedimentary formations from surface drill sites. Also presented is a description of drilling with wire-line equipment from an underground location in metamorphic rocks. The studies were conducted in the Colorado Plateau area and in northwestern New Mexico and Wyoming. Statements of a general nature pertain to conditions or situations existent in those areas.

Jan 1, 1960

By John Ward Smith

This paper describes and evaluates a method that the Federal Bureau of Mines used to determine the ultimate composition of the organic material in 10 samples of oil shale from the Mahogany zone of the Green River formation in Colorado and Utah. Since interest has centered on the Mahogany zone, the richest section of the deposit, these 10 samples were chosen to provide a broad representation of this zone with the objective of obtaining generally valid ultimate composition values. The most probable organic composition for the Mahogany zone and the 95-percent confidence limits for each component average (in weight-percent of organic material) are: Carbon 80.5 ± .4 Hydrogen 10.3 ± .1 Nitrogen 2.4 ± .1 Sulfur 1.0 ± .1 Oxygen 5.8 ± .5 As only minor variations in composition were observed, the organic material of this particular bed is quite similar over a wide geographic area.

Jan 1, 1961

By Robert Bottge

When a company develops a mineral property in a remote area of Alaska, it must consider how best to house its personnel. This Bureau of Mines report examines the economics of two options: company towns and company camps. The price required to maintain a 15% discounted-cash-flow rate of return (DCFROR) was derived for hypothetical 1,000-st/d cut-and-fill mines and 50,000-st/d open-pit mines located in three different regions of the State, One set of hypothetical mines utilizes a townsite; the other utilizes a relatively new concept, a fly-in camp or commuting operation, in which two shifts of employees operate the mine and all associated facilities for 1 week before being replaced by a second crew. The study shows that operating costs were higher for mines employing the commuting option than for mines having a company town because of the additional wages paid for overtime hours; however, the price required to obtain a 15% DCFROR for the single-product copper concentrate, f.0.b. the mill site, was significantly lower owing to the lower investment costs for the camp-type operation. The economic advantage for those mines utilizing the camp increases from south to north and from the coast toward the interior.

Jan 1, 1986

By W. W. Odell

Engineers interested in the manufactured-gas industry have witnessed p pronounced improvements in gas-generating equipment and marked changes in operating procedure during the past decade. In spite of these changes, however, the trend of development in the near future seems to be doubtful. Uncertainty exists mainly because no one can yet accurately calculate the number of years which will elapse before petroleum products become too expensive for, general use in making gas. Research in this field has been active, and the ultimate results are awaited with interest. Some engineers predict that in the future coking coal will be carbonized on such a large scale that coal gas will be used (straight or modified) for city distribution; others maintain that gas oil will be used in large quantities in the production of base gas; they believe that it will be economical to use oil even at appreciably higher prices. The question involves, among other; factors, consideration of initial and relative costs of equipment, flexibility of operation, salability of coke, cost of distributing different gases, and the relative value of by-products, It is common belief that for many years large quantities of oil will be used in gas-making, particularly in the generation of peak gas or that water gas will be used for the synthetic production of hydrocarbons to enrich additional water gas. In this paper interest centers in a discussion of the practicability of employing synthetic processes in view of reported investigations of the chemistry of the synthetic reactions. For many years it has been known that the chief components of water gas would react chemically under proper conditions to form methane. As long ago as 1903 a patent3 was issued in this country for a gas-making process which included the synthetic production of methane. More recently the studies of numerous investigators here and abroad have shown that besides methane it is possible to produce other paraffins, olefins, and additional, materials adaptable for enriching water gas or for other uses. The question arises: In what manner, if at all, can such processes be incorporated, as a part of the gas-making scheme in a city-gas plant?

Jan 1, 1928