Search Documents

By A. Renton Amell

The rate of dissolution of U02 was measured in acid solutions similar to those used for in situ leaching, with S04 of 10-1.82 to 10-4 M, Fe(III) of 10-2 to 10-4 M and pH's of 1.1 to 2.3. The dependence of dissolution rate on pH was small and inconsistent, probably reflecting the combined effects of a very weakly polar oxidizing complex, probably FeSO4+, and a nearly neutral U02 surface. Differences in the state of the U02 surface may explain this variability as well as contrasts between these results and results reported in other work. Changing either S04 or Fe(III) concentrations significantly affects dissolution rates. Increasing low sulfate concentrations in solutions containing 10 2 M Fe(III) at pH 2 results in formation of FeSO4+. In such solutions, rates increased with (S04)/(Fe(III)) up to 1:30, thereby indicating that the oxidation of U02 by FeSO4 is more rapid than by Fe3+. However, the dissolution rate decreased at higher (SO4)/ (Fe(III)), due either to sorption of SO42- on the UO2 surface or to formation of other less reactive sulfate complexes such as Fe(S04)2 or FeHSO4+ However, Fe(III) concentration is the dominant factor in determining solution rates. The rate was directly proportional to ferric iron concentration, indicating that the rate-determining step of the dissolution reaction is a single-electron oxidation by a ferric complex. Dissolution rates were lower in solutions of 0.1 and 1.0% H202 (0.029 and 0.29 M) than at similar concentrations of ferric iron because of formation of an insoluble surface coating of uranium peroxide, UO4?4H20. This phase may limit the value of hydrogen peroxide as an oxidant in lixiviants, not only by its very low solubility, but perhaps also by filling pores and reducing permeability in the ore body.

Jan 1, 1978

By R. Vernon Helm

Four tables listing values for the various physical properties of those sulfur compounds most likely to occur in petroleum and petroleum products are given herein. The data necessary to bring the first compilation2/ in this subject up to date are given in table I -Revised and Additional Data, which includes boiling points, refractive indices, densities, and freezing points. Tables 11-, III, and IV are published for the first time and include refractive indices for the F, C, and G' lines of hydrogen and the helium D:3 line; surface tensions and viscosities, and refractivity intercepts, specific dispersions, specific refractions, and parachors. The need for information concerning the sulfur compounds in petroleum is becoming-more urgent because of the necessity of refining larger quantities of high-sulfur crude oil to meet the rising demand for petroleum products. For a number of years the Bureau of Mines has been engaged in research to make available more information concerning the properties of the sulfur compounds in petroleum. The petroleum industry has recognized the value of such studies, and as a result the American Petroleum Institute has established Research Project 48A to study sulfur compounds. The investigations under this Project are to be done in Bureau of Mines laboratories as a cooperative project in connection with the work already started.

Jan 1, 1949

By R. V. Ramani, P. M. T. White, D. Sutton

Appendix I. Part 1: Description Of Geology & Reserves System Introduction The Ore Evaluation and Reserve programs have been developed to aid in the evaluation of coal deposits, both qualitatively and quantitatively. The "Weighted Moving Average" technique used provides considerable flexibility in dealing with diverse parameters with differing distribution characteristics. Determination of Model Constants "a" and "k" - Unit 1 The flexibility of the method in dealing with diverse value parameter distributions lies in its ability to cater to the individual characteristics of each. These characteristics are embodied in the values determined for constants "a" and "k", namely, local and regional variations in value distributions, respectively. The empirical method used attempts to optimize the "a" - "k" combination. Realistic values for "a" and "k" are entered into the program together with sample values for the required parameters and their respective coordinate location values. All the values within a specified radius from the point being evaluated are used to interpolate a value at that point. (Note, the interpolated point is the location of one of the boreholes, values of which are not used in the calcula¬tion.) 3n a similar manner, interpolated values are calculated for each borehole location and for each parameter. This is done for each possible combination of "a" and "k".

Jan 1, 1974

By William L. Crentz

Pike County in the easternmost portion of Kentucky is one of the major coal-producing areas in the eastern Kentucky coal field. The county contains numerous coal beds, many of which are too thin to support mining. The commercially important beds are usually 4 feet or more thick, but selective mining at some places calls for removal of a much thinner section of the bed. The variation in quality of the beds from place to place and the large number of coal beds make correlation uncertain. Samples were collected from 14 different coal beds, of which the Elkhorn group is by far the most important. In addition to the Upper Elkhorn No. 3, Upper Elkhorn No. 2, Upper Elkhorn No. 1, and Lower Elkhorn beds that comprise the Elkhorn group, the Winifrede, Williamson, and Bingham beds constitute the principal coal deposits in Pike County.

Jan 1, 1952

By Joseph Berman

The wolframite mineral series was studied to determine the effect of the FeO - MnO ratio on unit cell symmetry and thermal stability. This work was undertaken to evaluate the analytical procedures now in use for wolframite in scheelite and to aid in the development of improved methods of analysis. Wolframite grains were hand-picked, crushed, and screened; impurities were removed by selective magnetic separations using a Frantz isodynamic separator. The samples were further checked by optical spectroscopic and microscopic examination.

Jan 1, 1957

By Clayton A. Landsidle

There has been little change in timbering methods in anthracite mines for 75 years, and technical information on strata control is almost wholly lacking. In order to assist the industry to establish technical data, the Bureau of Mines and a Northern field operator are cooperating in underground experiments, the first phase of which has been to investigate pneumatic packing. The four principal methods of packing in mining are hydraulic, pneumatic, mechanical, and hand. The hydraulic pa caring system is believed to have originated at Shenanodah, Pa., in 1864,4/ to prevent destruction of a church by surface subsidence after underground coal mining. This method was used again in 1884 to arrest an underground fire at Buck Ridge colliery, near Shamokin, Pa. In 1901 hydraulic packing was introduced to Europe in Upper Silesia, where it gained in popularity owing to the availability of large quantities of sand suitable for flushing .5/ Hydraulic packing has a number of disadvantages. Chief among these are the softening effect of large quantities of water on the mine floor conducive to heaving action; drainage and punning costs; and the inability to fill roof cavities completely in flat beds.

Jan 1, 1953

By Jeffrey A. Shibe

A prototype Fire Safety Evaluation System has been developed and is ready to be evaluated by a Peer Consulting Panel and for performing field tests. The system can be used to determine combinations of widely accepted fire safety equipment and under-ground coal mine features that provide a level of safety equivalent to those required by the Code of Federal Regulations-Title 30 for underground coal mines. In this evaluation, equivalent safety performance is gauged in terms of overall level of safety provided rather than by a component by component comparison.

Jan 1, 1987

By Thomas M. Nasiatka

Tests with a high-pressure water jet were conducted in the steeply pitching Roslyn No. 5 bituminous coalbed in the Roslyn No. 9 mine, Roslyn, Wash., to determine the feasibility of extracting coal from pillars and from a solid coal face in development without drilling and blasting. During pillar mining, using a hand-held monitor, the best results were obtained with a 0.150-inch- diameter nozzle, a water pressure of 3,500 psi, and a flow rate of 38.5 gpm.3 The rate of mining and productivity were 0.74 ton per minute and 16.6 tons per man-shift, respectively. During development mining, using a monitor mounted on a roof jack, the best results were obtained with a 0.148-inch-diameter nozzle, a water pressure of 4,500 psi, and a flow rate of 40.0 gpm. In one section of the mine where the coal was relatively hard, the rate .of mining and productivity were 0.10 ton per minute and 5.7 tons per man-shift, respectively in another section of the mine where the coal was relatively soft, the rate of mining and productivity were 0.51 ton per minute and 8.3 tons per man-shift, respectively. The tests showed that hydraulic mining methods were more productive than conventional mining methods in pillar mining. In development the productivity of hydraulic mining depended primarily upon the coal hardness. Compared with conventional methods, hydraulic mining methods were less productive where the coal was relatively hard and equally as productive where the coal was relatively soft.

Jan 1, 1963

By G. E. McElroy

This report discusses the construction and use of an all-pressure psy- chrometric chart in which the requirements of simplicity of appearance and absolute accuracy have been waived, to a certain extent, to provide for the rapid determination of psychrometric data and for the rapid solution of air- conditioning problems of major interest to the mining industry. Many mines in which air-conditioning problems are important are situated at elevations far above sea level and embrace great differences in elevation - in excess of 8,000 feet in certain mines → throughout their airflow circuits. Under these conditions, the effects of variations in the pressure of the at- mosphere upon the physical properties of the mixture of air and water vapor of which it is composed are considerable and should be taken into account in the solution of problems. The simple types of psychrometric charts in common use, such as the Carrier, Bulkeley, Hill, and Goff (American Society of Heat- ing and Ventilating Engineers Guide), are not generally suitable, in that they are drawn for a single barometric pressure 29,92 inches mercury.

Dec 1, 1947

By W. L. Dare

This publication is one of a series by the Federal Bureau of Minus describing methods and costs of minim, uranium on the Colorado Plateau. The La Sal mine is in the Big Indian mining district, about 29 miles southeast of Moab, San Juan County, Utah. The claims that encompass the mine were located in March 1953, and the La Sal ore body was discovered as a result of a drilling program begun in August 1953. The mine is owned by the La Sal Mining & Development Co., a subsidiary of the Homestake Mining Co. Homestake continued the drilling program and in May 1954 began sinking a 572-foot shaft and constructing a surface plant. The plant and shaft were completed in October 1954. The La Sal ore body is in the Chinle (Triassic) formation. it is tabular and dips with the enclosing beds about 8° southwest. The ore body is generally 4 to 8 feet thick but in a few places is as much as 20 feet thick it is being developed by a series of strike drifts and dip inclines, driven within the ore stratum on about 100-foot centers. A haulage level driven beneath the ore body is connected by raises to the upper workings.

Jan 1, 1957

By W. P. Huleatt, Jr. Traver, Jr. Hazen

"Vanadium and uranium occur widely distributed throughout western Colorado and eastern Utah, and a few deposits have been found in northeastern Arizona and northwestern. New Mexico. The area in which it occurs includes approximately 10,000 square miles and is generally referred to as the vanadium region of Colorado and Utah.The majority of the deposits consist of replacement bodies and impregnations of rare minerals in the lower Morrison formation of Jurassic age. The ore bodies are flat, with irregular margins, and most of them conform to the stratification.The ""rim rock"" topography of the region includes many steep-walled canyons and plateaus, which afford an abundance of outcrops that have been responsible for most of the discoveries of mineralized areas. Delimitation of ore bodies within the areas is accomplished most effectively by core drilling from the surface.The deposits were discovered in 1899 and from 1911 to 1923 wore worked extensively for radioactive uranium ores, principally carnotite.The discovery and marketing of the richer and more cheaply mined pitch-blende ores of the Belgian Congo left the Colorado-Utah deposits without economic importance as sources of radium and uranium, and the region became inactive in 1923. After a period of comparative inactivity, the rising demand of the alloy-steel industry for vanadium renewed interest in the deposits, which were known to contain that metal. By 1938, vanadium production in the area had achieved respectable proportions, and new impetus was given to it by the United States’ entry into World War II in December 1941. In 1942, new treatment plants for vanadium ores were completed in Monticello, Utah, and Durango, Colo. In order to meet the requirements of these and other plants in the region, it became necessary to open new vanadium mines and prepare old onus for production.In an effort to stimulate mining, the Metals Reserve Company initiated a stock-piling program and appointed the united states Vanadium Corporation, to act as its purchasing agent.The extra production was expected to come largely from small, independent operators whose limited funds did not permit them to maintain development and exploratory programs. Study of conditions made it apparent that extensive exploration would be necessary to sustain production, and accordingly the Bureau of Mines initiated an exploratory drilling project on a cooperative basis with the Geological Survey. The principal objects of the work were to enlarge the known ore reserves of the area and, if possible, discover new ones. The results have been gratifying in both respects."

Sep 1, 1946

The Interior Department's Bureau of Mines is the Federal Government's primary research arm in the mineral and fossil-fuel fields. In accordance with its Organic Act of 1910, the Bureau's responsibilities have been reinforced since the passage of the Federal Metal and Nonmetallic Mine Safety Act of 1966, the Federal Coal Mine Health and Safety Act of 1969, and the Mining and Minerals Policy Act of 1970. The 1966 and 1969 acts deal specifically with the development of safe working conditions and a healthful working environment for those engaged in the mining industry, while the third sets the national policy as follows: " ... to foster and encourage private enterprise in (l) the development of economically sound and stable domestic mining, minerals, metal, and mineral reclamation industries; (2) the orderly and economic development of domestic mineral resources, reserves, and reclamation of metals and minerals to help assure satisfaction of industrial security, and environmental needs; (3) mining, mineral, and metallurgical research, including the use and recycling of scrap to promote the wise and efficient use of our natural and reclaimable mineral resources, and (4) the study and development of [ ]

Jan 1, 1972

By D. J. Hawk

The mechanical properties of coal are often represented by the orthotropicmaterial model, which consists of nine elastic constants. The material symmetries involved are found in coal primarily because of the natural process by which it was formed. In this thesis the material properties of five U.S. coals, as obtained from cubical testing, are examined, using as a basis for comparison the assumption of the orthotropic material model. An analysis is performed on each set of coal material data in order to examine its conformability to other, less complex material models, these being the transversely isotropic model consisting of five elastic constants and the 'isotropic model consisting of two elastic constants. In addition, the material properties of two American shales are analyzed, based on the assumption that they comply with the transversely isotropic model. An analysis similar to that performed on the coal material is applied to the shale in order to determine the conformity of its material properties to the isotropic model.

Jan 1, 1980

By FRANCIS FEEHAN

Safety first is no longer merely a motto ; in some industries and in some parts of the mining industry it is an accomplished fact . In connection with the National Safety Competition of 1928 in which 284 mines and quarries participated , 42 plants were operated without a single lost - time accident . The winning company in the bituminous group had an accident severity rate of 0.053 per thousand man hours of exposure . Excellent safety records of various kinds are becoming more and more frequent , and the indication is that in reality safety is first in many mines and qquuaarrrriieess .. The safety achievements in the Stewart mine of W. J. Rainey , Inc. , are unusual even among mines winning awards in the competition .

Apr 1, 1930

By P. L. Woolf, N. Bernstein, M. M. Fine

Continuous experimentation utilizing a 3- by 36 - foot rotary kiln was conducted to demonstrate the feasibility of simultaneous induration and reduction of magnetic taconite concentrate . Lignite , or lignite - anthracite mixtures , and green magnetite pellets (64.2 percent Fe , dry basis ) were heated in a rotary kiln to about 2,100 ° F. After separation from excess reductant , the product pellets were found to be highly reduced and acceptably hard . A total of 140 tons of prereduced pellets with an average Fe content of 79.0 percent was produced at Minneapolis and smelted in the Bureau's experimental blast furnace at Bruceton , Pa . Two additional supplies of prereduced pellets were obtained from The Steel Company of Canada , Ltd. , Hamilton , Ontario , which contained 83.8 and 91.3 percent Fe , respectively . Smelting of prereduced pellets was compared with that of unreduced pellets obtained from The Hilton Mines , Shawville , Quebec , and from the Erie Mining Co. , Hoyt Lakes , Minn . Blast furnace tests established that a substantial decrease in coke rates and higher production result from the use of prereduced pellets .

Jan 1, 1964

By J. M. Goris

The U.S. Bureau of Mines is conducting research on cable bolt ground supports to assess their material and support properties, to provide design criteria for using cable bolt supports as roof control systems under various types of underground mining conditions, and to provide a mathematical model of cable bolt support systems. Part 1 describes laboratory studies of the support properties of cable bolts made of conventional steel cables and provides recommendations on such topics as the use of thick grouts, selection of breather tubes, and reduction of water bleeding in cement-based grouts. The studies evaluated both single and double cables; effects of different embedment lengths, water-cement ratios, and grout curing temperatures on support strength; effects of use or nonuse of breather tubes; pumpability and water-bleeding properties of grouts; and the strength properties of sand-cement grouts. Part 2 will cover the strength characteristics of birdcage cable bolt supports, epoxy-coated cables, and cables with steel buttons attached.

Jan 1, 1990

By Richard Quirk

This report describes methods and techniques employed by The Glidden Co. of Cleveland, Ohio, in explorating an ilmenite-bearing sand deposit in Ocean County, New Jersey, during 1960 to determine ore reserve potential and the feasibility of mining and establishing a milling plant on the property for the production of ilmenite concentrate. The property covered approximately 1,250 acres. Comprehensive sampling by water-jet drilling indicated the deposit averaged 20 feet in thickness and contained 4.5 percent heavy minerals, of which 80 to 85 percent was ilmenite and leucoxene. Average depth of the water table as determined by auger boring was 16.8 feet. Pilot plant tests indicated that circular concentrators in combination with spiral concentrators would recover at least 80 percent of the heavy mineral content of the sands. It was estimated that sufficient ore reserve tonnage had been developed to supply the company's Baltimore chemicals division, pigments department, with a suitable grade ilmenite concentrate for a period of 20 years at the present rate of pigments production. The property was designated as Lakehurst mine and plans are in progress for mining development and plant construction.

Jan 1, 1963

By R. Blickensderfer

The laboratory wear testing capabilities of the Bureau of Mines are described, Wear tests are used to support the Bureau?s research efforts toward reducing the wear of equipment used for mining and minerals processing and any wear involving a loss of strategic or critical materials. The emphasis is on abrasive wear because it accounts for most of the wear losses that occur in mining and minerals processing equipment, Spalling wear, caused by repetitive impact in grinding equipment, also is included, Ten abrasive wear tests, including high- stress and low-stress and two-body and three-body conditions, are described: dry-sand, rubber-wheel abrasive wear; Taber Abraser; abrasion resistance of refractory materials; dry-particle erosive wear; elevated-temperature, dry-particle erosive wear; low-angle slurry pot; jaw crusher gouging wear; ball mill wear; pin-on-drum abrasive wear; and high-speed impact gouging. Two repetitive impact tests are described: ball-on-block impact-spalling and ball-on-ball impact-spalling. Test equipment, procedures, and specimens are described, and typical test results are presented and discussed.

Jan 1, 1985

By Jane Applegate

This report documents efforts to design, develop and test a training approach which would assist front-end loader operators in the acquisition of skills and awareness to reduce the probability of their involvement in accidents in the mining environment. The goal of this project was to prepare and use (on a trial basis) a training method and materials which would be generally applicable to any loader and surface mining operation while at the same time, be adjustable by mine personnel to meet the specific needs of each mining operation. This effort resulted in the Front-End Loader Training System, a structured, performance-based training approach with diverse instructional aids and classroom and on-machine training experiences. Validation of the System at a large western mine demonstrated the utility and flexibility of the training approach and materials.

Jan 1, 1983

By H. R. Babitzke, H. Kato, M. D. Carver

A number of columbium and tantalum alloys were investigated to determine their suitability for use at elevated temperatures . Columbium-vanadium , tantalum-vanadium , and tantalum-hafnium alloys , and also columbium- 10 wt pct titanium alloys modified with additions of 0.1 to 2 mole pct ZrO2 , TiO2 , ZrB₂ , TiB , ZrC, or TiC were prepared and examined . Workability , tensile properties , and oxidation resistance were tested . Of the columbium alloys studied , the columbium- 12 at . pct vanadium exhibited the best properties ; it compared closely with the columbium- 10 at . pct vanadium alloy studied in a previous investigation.

Jan 1, 1964