Search Documents

By Donald O. Capstick

The U.S. Bureau of Mines conducted an inventory of the prospects and mineral resources in the Scodies RARE II area (No. 5212) in 1982. No mineral production is recorded from the area, and no mines are being developed. The Scodies RARE II area is comprised primarily of light colored granodiorite with minor inclusions of mafic granitic rocks. Late stage differentiates of magmas resulted in quartz veins and pods. Metasedimentary rocks which have been mineralized in some parts of the Sierra Nevada were not observed within the study area during this investigation but small inclusions have been reported.

Jan 1, 1983

By G. J. Hundman

Control of respirable dust produced by auger type continuous mining machines is normally attempted by water sprays from fixed nozzles mounted on the frame of the machine. In tests conducted under this contract, a 'wet auger' system was used, where the spray nozzles were mounted on the rotating auger itself. The tests were conducted at the Hunter mine of Smith and Stover Coal Company using a Jeffrey 1.00L auger miner. Operating the mining machine in the wet auger mode, it was found to produce 47 pct less respirable dust than when the fixed conventional sprays were used. On section dust levels were reduced too 3.5 mg/m3 which is equivalent to approximately 2.0 mg/m3 for a full shift portal to portal sample. The major difficulty that had to be overcome was the development of a simple reliable water transfer mechanism to get the water into the rotating augers. This was successfully achieved by the development of a water-through-the-shaft water system. This system can be retrofitted to existing machines and is available in kit form.

Jan 1, 1977

By C. Lurie

This final report describes the work performed by Gulton Battery Corporation under USBM Contract No. HO-112033, entitled "Research and Development on Lithium-Nickel Fluoride Batteries For Mint Life Support Equipment". The lithium-nickel fluoride couple was chosen For this investigation because of its high theoretical energy density (626 Wh/lb), its ability to operate at ambient temperatures and the fact that it showed promise as a secondary system. The theoretical energy density of the lithium-nickel fluoride couple is ten times greater than that of the widely used lead-acid battery and three times greater than the silver-zinc battery which has the highest theoretical energy density of the commercially available secondary systems. The experimental program first evaluated the cell components individually. The results of these studies then formed the basis for investigations of cell performance using experimental three-plate cells. These cells consisted of one nickel-fluoride and two lithium electrodes. All work was performed in a glove box under an argon atmosphere which was sufficiently pure to maintain the shiny appearance on freshly prepared lithium surfaces. The major portion of the work effort was concerned with the nickel fluoride electrode. Binder, conductive diluent, fabrication technique, as well as the nickel fluoride active material itself, were considered. Criteria for binder materials were established and six classes of materials encompassing thirteen binders were evaluated. The candidate materials were initially screened for appropriate chemical and physical properties and finally evaluated in three.-plate cells, Two epoxy powders emerged as the most promising binders. Two types of conductive diluent were evaluated. The first is a carbon black of low bulk density and high surface area. This material is a good conductive diluent; however, electrodes fabricated with it lacked good mechanical strength. It was hypothesized that a uni¬form, small particle size, low specific surface area would improve the mechanical properties of the electrodes. Therefore, two samples of graphicic materials, milled to uniform powders in the one-to-ten micron range were evaluated. Electrodes prepared with the graphitic materials had superior mechanical properties, However, their electrical performance was significantly poorer and voltage losses of 0.2 to 0.3 volts were observed. Several electrolyte solutions were evaluated. N-Methyl-2-Pyrrolidone was tested but found to be incompatible in the presence of lithium. Lithium perchlorate, lithium hexafluoroarsenate, and lithium bromide were tested as two-component electrolytes in propylene carbonate solvent and their performance compared with that of the single electrolyte solutions, Lithium perchlorate gave the best performance. Lithium hexafluoroarsenate was also evaluated in methyl formate and appears to give equivalent performance. The lithium perchlorate-propylene carbonate system is preferred as it is easier to handle and less expensive.

Jan 1, 1973

By G. W. Jones

As a part of its general safety program the Bureau of Mines has investigated various means useful for the elimination or mitigation of the explosion hazards in connection with combustible gases incident to the mining industry. Information has been obtained relative to the explosibility of numerous simple and complex gaseous combustible atmospheres. Although experiments along this line have pertained largely to combustible gases in the mining and allied industry, considerable information has been obtained relative to the explosive hazards of combustible gases and vapors used as anesthetics.

Jan 1, 1939

By Hugo E. Camargo

Noise Induced Hearing Loss (NIHL) is the most common occupational disease in the U.S. with devastating consequences particularly in the mining industry. A study conducted by the National Institute for Occupational Safety and Health (NIOSH) revealed that 90% of coal miners have hearing impairment by age 50, compared to only 10% of those not exposed to occupational noise. According to the Mine Safety and Health Administration (MSHA), Continuous Mining Machine (CM) operators account for 30% of workers exposed to noise doses exceeding the Permissible Exposure Level (PEL). This number becomes more dramatic considering that 49% of the total national underground coal production is extracted using these machines. In this context, NIOSH is conducting research to identify and control dominant noise sources in CMs. Previous noise source identification was performed using a Brüel &Kjær (B&K) 1.92-m diameter, 42-microphone phased array. These measurements revealed that the impacts from the conveyor chain onto the tail roller, and the impacts from the conveyor chain onto the upper deck are the dominant noise sources at the tail-section of the CM. The objectives of the work presented in this paper were: 1) To rank the noise radiated by the different sections of the conveyor, and 2) to determine the effect of a urethane-coated tail roller on the noise radiated by the tail-section. This test was conducted using an Acoustical and Vibrations Engineering Consultants (AVEC) 3.5-m diameter, 121-microphone phased array. The results from this new test show that a urethane-coated tail roller yields reductions in the tail-section of 2 to 8 dB in Sound Pressure Level in the frequency range of 1 kHz to 5 kHz. However, integration of the acoustic maps shows that the front-section and mid-section of the conveyor also contain dominant noise sources. Therefore, a urethane-coated tail roller in combination with a chain with urethane-coated flights that reduces the noise sources in the front and mid sections of the conveyor is required toyield a significant noise reduction on the CM operator?s overall exposure. These results show the applicability of phased array technology for low frequency noise source identification.

Jan 1, 2008

By Hillary W. St. Clair

The reduction zone of the iron blast furnace is represented by a mathematical model of the chemical reactions and heat transfer that occurs between gas and solids during the deoxidation of iron oxide. The model consists of a set of equations and an algorithm whereby the equations may be solved to give the temperature and composition of gas and solids at any position in the reaction zone and at any time after a specified initial state. The model is applied to the special case in which ferric oxide is reduced by graphitic carbon and carbon monoxide produced by burning carbon in dry air. The rate of reduction, carbon consumption and maximum temperature are shown as functions of the temperature and rate of flow of the incoming reducing gas and external heat loss. The model of the reduction zone is the essential part of a general mathematical model for simulation of the iron blast furnace. The simulation model will serve as a research tool to be used in conjunction with an experimental or operating furnace. After the simulation model has been correlated with the real furnace, it is proposed that further experimentation be done mostly with the model. The real furnace will then be operated primarily to test and confirm the model.

Jan 1, 1967

By G. W. Jones

As a part of its general safety program the Bureau of Mines has investigated various means useful for the elimination or mitigation of the explosion hazards in connection with combustible gases incident to the mining industry. Information has been obtained relative to the explosibility of numerous simple and complex gaseous combustible atmospheres. Although experiments along this line have pertained largely to combustible gases in the mining and allied industry, considerable information has been obtained relative to the explosive hazards of combustible gases and vapors used as anesthetics.

Jan 1, 1939

By ROLLIN THOMAS CHAMBERLIN

The studies herein reported were begun as a part of researches undertaken by the United States Geologü;al Survey looking to the more effcient utilization of the coal in the United States through the reduction of waste in its extnidion, and were continued as part of further researches having regard to the conservation of the fuel resources of this country and to the lessening of injuries and fatalities in coal mining. Among other phases of the general problem to be studied were the origin of the gas whidi escapes into coal mines, its modes of occurrence in the coal and rock strata, and the conditions governing its outflow into the mines. The subject of relative danger from destructive explosions due to gas and coal dust in different mines belonging to different coal fields was to be one of the principal lines of investigation. But this work was barely under way when the series of unusually disastrous explosions in the Naomi, .Monongah, and Darr mines of Pennsylvania and West Virginia, in December, 1907, afforded an exceptional occasion to observe the behavior of explosions on a large scale. Because of the opportunities for study afforded by these terrific explosions, the inquiry originally planned was d ¡verted to the more specific investigation of the conditions in tl10SC mines, and the examinations have been directed toward finding those qualities of gas and dust which were concerned in these explosions. The following discussion, therefore, consists essentially of a report on that subject; but it is far from being exhaustive, and is to be regarded as a preliminary outline of investigations which are still in progress. The first of the three mine explosions mentioned occurred in the Naomi mine of the United Coal Company, near Bellevernon, Pa., on Sunday, December 1, at 7.40 p. m. All the men who were within the mine at the time, fortunately only 34, were killed. Less than a week later there occurred in mines Nos. fì and 8 of the Fairmont Coal Company at Monongah, W. Va., the most disastrous mine explosion yet recorded in the annals of American mining. The mines were comparatively new and well laid out. Mine No.8 had been in operation only about two years and was the pride of the Fairmont Coal Company. Mine No.6 was first opened ahout four years earlier. In order to make it possible, in case of emergency, for either mine to be ventilated by the ventilating system of the other, the two sets of workings were connected underground. The F face heading of mine K o. 6 led direetly into No.2 north heading of No.8 mine. On Friday, Dcccmber 6, at about 10.30 in the morning, an explosion of unusual violcnce swept completely through both mines, pursuing its course throughout the numerous ramifications and bursting out of the two pit mouths, located It miles apart, nearly simultaneously. The slope of mine No.6 was only slightly damaged, but at the mouth of No.8 the destruction was very great. The fan was wrecked, the engine house was demolished, and mine timbers were blown across Monongahela River: As nearly as can be determined, 361 men were killed in the two mines by the explosion. .While the inspection of the Monongah mines was still in progress, on Thursday morning, December 19, at about 11.20, a similar explosion wrecked the Darr mine of the Pittsburgh Coal Company ut Jacobs Creek, Pu.; 238 men lost their lives in this explosion, which in number of casualties is second only to the :Monongah disustcr in the history of American mining. Of ull thc men in the mine at the , time of the explosion, only one mun, who happened to be within 100 feet of the ~iUrface on an old manway in a wet, unexploded portion of the mine, succeeded in escaping alive. The underground investigation of these mines was made in cooperation with Clarence Hall and ""Valter O. Snelling, of the United States Geological Survey, and James ""V. Paul, now of the Survey but at that time chief of the department of mines for vVest Virginia, to all of whom the author is greatly indebted for valuable assistance, suggestions, and advice. Mr. Paul will rcport on the nature of these explosions, the precipitating causes, their destructiveness, and the general cüliditions in these mines following the disasters. The present report is confined essentially to the laboratory examination of some of the explosive materials collected from these mines directly ufter the explosions.

Jan 1, 1911

By John J. Sammarco

The U.S. Bureau of Mines has developed a regulated, intrinsically safe, rechargeable power supply for portable electronic equipment for underground use. The regulated output is ideal for microprocessor power requirements and is suited for operation in hazardous environments. Two rechargeable, sealed batteries are contained within the power supply. Provisions are made to use an external source of power if these batteries fail. Provisions are also made to charge these internal batteries when needed. The circuit is composed of three main circuits: the main regulator circuit, the input protection circuit, and the output protection circuit. The main regulator circuit provides remote voltage sensing, current sensing, fault monitoring, and internal thermal protection. The input protection circuit checks for excessive input current and low battery conditions. The output protection circuit contains two overvoltage detection devices. Schematics, a parts list, and a calibration procedure are provided in this report to enable readers to fabricate the power supply.

Jan 1, 1989

By Larry R. Powell

As part of the Bureau of Mines effort to establish a comprehensive subsidence data base for subsidence technology development, subsidence and related data are being compiled for various mining, geological, and environmental situations. This publication presents data for a longwall mining operation in the Northern Appalachian Coal Region. Vertical displacements and relative faze positions are tabulated for 160 subsidence monuments. Measurements were taken 32 times during the 2 years it took to mine the two panels. Brief physiographic and geological descriptions of the mining site are presented along with a general account of the mining and subsidence monitoring methods.

Jan 1, 1981

By S. H. Lorain

This paper briefly describes the principal commercial and near-commercial deposits of gold-bearing gravel and the important placer-mining operations in Lemhi County, Idaho. It is on of a series on western mining districts being published by the Bureau of Mines. This paper is based on a field survey of the placer-mining districts of Lemhi County in the summer of 1938. Available information concerning gold-bearing gravels was obtained from prospectors and claim owners; operators supplied the data on mining operations. No attempt was made actually to test the gravels. The principal object of the examination was to indicate placer areas worthy of further investigation by prospective operators.

Jan 1, 1939

By James A. Wasson, Harry R. Johnson, Dean W. Boley

The Cow Run sand was cored and electrical and radioactivity surveys were made in C. E. Vandevender well 35 in the Burning Springs pool of the Burning Springs oilfield , Wirt County , W. Va . Laboratory tests , reservoir - fluid analysis , well - log interpretation , and available field data indicate that a substantial quantity of oil may be recovered from this pressure - depleted reservoir by waterflooding . Two formations erroneously believed to be the First and Second Cow Run sands were similarly evaluated in A. E. Mackintosh well 8 , Anns Run Pool , Wirt County , W. Va . , but were found unsuitable for secondary - recovery operations .

Jan 1, 1964

By H. P. Greenwald, Irving Hartman, H. C. Howarth

"INTRODUCTION A report of tests of seven small pillars formed from the Pittsburgh coal bed in the Experimental coal mine was given in Technical Paper 605 5/ Five additional pillars were tested between July 1939 and. October 1940. The data obtained, in the later tests permit an extension of the conclusions reached in Technical Paper 605, which appears to be important enough to the mining industry to justify a progress report that will explain briefly what it is and how it was obtained. Full detail of the tests will appear in a second technical paper, preparation of which is deferred so that results of pillar tests now under way my be included.DESCRIPTION OF TESTSExcept for minor improvements in operating details, the five additional tests were made as described in Technical Paper 605, pages 2 to 7. Briefly, the desired pillar was formed from the coal bed, by excavating a passage around it (no explosives were used), and enough material was removed from above to permit installation of the assembly used for applying pressure. Each pillar was tested resting on its original fireclay floor, which was restrained from lateral flow by a ring of concrete. Vertical and lateral movement of the pillars in two directions as measured carefully in all tests."

Jun 1, 1941

The purpose of this study is to formulate practical guidelines for active underground mining in close proximity to water bodies. This was accomplished through systematic completion of three phases of study: I) Collection and Documentation of Data; II) Application of Existing Guidelines to Case Histories of Previous Inundations; and III) Development of Recommended Guidelines for Underground Coal Mining Near Bodies of Water. Phase I of the study involved a worldwide data collection effort designed to obtain foreign and domestic guidelines for mining near water bodies, and accident records and case histories of accidental mine inundations. Within Phase II, existing guidelines were categorized and classified and then evaluated as to their effectiveness in precluding past inundations had they been in effect at the time of inrush. Advantages and disadvantages of existing guidelines were defined. Drawing on the broad data base established in previous study efforts, Phase III was directed at development of viable guidelines to promote the greatest possible coal extraction while precluding accidental mine inundation. Two levels of guidelines are presented; Level I Guidelines require little or no subsurface exploration on the part of the mine operator, while Level II Guidelines recommend various testing and investigative procedures to permit greatest possible mineral extraction. This report presents findings and conclusions of the study.

Jan 1, 1976

By Jon G. Bredeson

The electromagnetic noise that exists in a mining environment is quite severe and was shown to have been reasonably well documented by a number of researchers in the Phase I Report. The noise levels are such that prudent communication design requires the careful use of all the electromagnetic noise data available. A comprehensive survey was undertaken to determine techniques used in various industrial environments to achieve secure communications in the presence of electromagnetic interference. The techniques were given in the Phase I Report and are rudimentary, but have produced reasonably good results. A number of these techniques could be applied to the mining environment.

Jan 1, 1980

By B. W. Gandrud

This report, consisting mostly of float-and-sink data and washability curves, has been prepared in connection with an exhaustive study of coal preparation in Alabama conducted, by the U, S. Bureau of Mines and the University of Alabama with the cooperation of the different coal operators On the basis of the float-and-sink data, an attempt has been made to determine approximately the extent of ash and sulphur reduction obtainable under given conditions on coal from the mines which were sampled, In the coal-producing districts of Alabama a great deaf of attention has been given in recent years to the problem of improving preparation methods so as to obtain from various coal beds the best possible grade of washed coal. This is especially so where the washed coal is used for the making of metallurgical coke in by-product plants or where there are possibilities of using the coal for this purpose. In the manufacture of metallurgical coke, the sulphur content of the coal is a very important consideration. It is quite often the determining factor as to whether or not a certain coal can be used for coke making. In the studies which form the basis for this report, all samples have been analyzed for sulphur in order to obtain information regarding the possibilities of sulphur elimination as well as ash reduction, and the samples on which reports are made were obtained from beds that are characterized by rather high percentages of sulphur. In connection with the present investigations of coal preparation in Alabama a standardized method of interpreting float-and-sink data has been used extensively for predicting the ash and sulphur reduction and yields obtainable in a commercial washing plant from various sizes of raw coal and from the raw coal as a whole after a certain degree of crushing. This method, which will be explained in subsequent chapters, was used in interpreting the data contained in this report. The samples used for these washability studies were obtained from the following mines in the Warrior field of Alabama: Beltona mine on the Jefferson bed; Dolomite and Mulga mines on the Pratt bed; Coal Valley No. 163 and Coal Valley No. 11 mines on the Corona bed; Cedar Cove mine on the Carter bed.

Jan 1, 1932

By B. W. Candrud

This report, consisting mostly of float-and-sink data and washability curves, has been prepared in connection with an exhaustive study of coal preparation in Alabama conducted by the U. S. Bureau of Mines and the University of Alabama with the cooperation of the different coal operators on the basis of the float-and-sink data, an attempt has been made to deter-mine approximately the extent of ash and sulphur reduction obtainable under given conditions on coal from the mines which were sampled. In the coal-producing districts of Alabama a great deal of attention has been given in recent years to the problem of improving preparation methods so as to obtain from various coal beds the best possible grade of washed coal. This is especially so where the washed coal is used for the making of metallurgical coke in by-product plants or where there are possibilities of using the coal for this purpose. In the manufacture of metallurgical coke, the sulphur content of the coal is a very important consideration. It is quite often the determining factor as to whether or not a certain coal can be used for coke making. In the studies which form the basis for this report, all samples have been analyzed for sulphur in order to obtain information regarding the possibilities of sulphur elimination as well as ash reduction, and the samples on which reports are made were obtained from beds that are characterized by rather high percentages of sulphur. In connection with the present investigations of coal preparation in Alabama a standardized method of interpreting float-and-sink data has been used extensively for predicting the ash and sulphur reduction and yields obtainable in a commercial washing plant from various sizes of raw coal and from the raw coal as a whole after a certain degree of crushing. This method, which will be explained in subsequent chapters, was used in interpreting the data contained in this report. The samples used for these washability studies were obtained from the following mines in the Warrior field of Alabama: Beltona mine on the Jefferson bed; Dolomite and Mulga mines on the Pratt bed; Coal Valley No. 16B and Coal Valley No. 11 mines on the Corona bed; Cedar Cove mine on the Carter bed.

Jan 1, 1932

By P. G. Pigott

This Bureau of Mines laboratory research demonstrated that building bricks meeting ASTM specification C62-66 for grades SW and MW of FBS-type bricks can be produced from waste copper mill tailings. Waste tailings from accumulations at Magna, Utah, Anaconda, Mont., and Hayden, Miami, and San Manuel, Ariz., were dry-pressed into bricks, and the products were tested in accordance with ASTM Designation C67-66 on sampling, and testing of brick. An evaluation derived from pilot-plant production of similar brick at the Coal Research Bureau of West Virginia University indicated the production cost to be about $34 per 1,000 bricks. Utilization of such mill tailings on a commercial scale would eliminate the need for digging new pits for brick raw material production, conserve natural resources, and simultaneously remove potential sources of air pollution.

Jan 1, 1971

By J. L. Kohler

The final report for Phase II of Bureau of Hines Contract J0134025 concerns the research and development of sensitive ground-fault relays for dc utilization systems in mining. Sensitive relaying employs very low pickup levels such that, when used in conjunction with very high resistance grounding, the exposure of a human to ventricular fibrillation is significantly reduced. To delineate the desired relay characteristics, the report begins by reviewing previous research in this area. A theory for the saturable transformer used to sense the fault current is presented. The design of the ground fault relay is described in sufficient detail that it may be duplicated. Test procedures and results are given. Finally, conclusions and recommendations related to Phase II are presented.

Jan 1, 1986

By T. T. Read, F. C. Houghten

"The bad effects upon the health and output of miners that result when the ventilating current in a mine lacks sufficient cooling power have been described by Harrington and Sayers in a previous report (1)*** The normal temperature of the human body is about 98.5°F. and whenever work is done by the muscles, indeed even when sitting still, the normal bodily processes generate heat which must be given off, otherwise the body will become overheated and a number of bad effects will be produced. If it were possible to so enclose a man that he could continue to breathe and no heat could escape from his body he would die within a short time. In a series of experiments made at the Pittsburgh Station of the Bureau of McConnell and Houghton (2) found that a dry-bulb and a wet-bulb temperature of 112.5°F could he borne for only 35 minutes, even when the subject was at rest. A wet-bulb temperature of 100.4°F (dry-bulb 157°F) could only be tolerated for 45°F minute. Under such conditions the bodily temperature rises as much as 45°F above normal and the pulse is accelerated. Very uncomfortable sensations are felt when the pulse rate exceeds 135. The human body, like any other internal combustion engine, must be cooled in order to function properly.Under ordinary circumstances the air surroundings people is enough coder than themselves to permit this heat generated within the boiy to be river off with¬out difficulty. At higher temperatures, or when the rate of work, with its corresponding generation of heat is high, the body can not throw off heat fast enough, so it begins to sweat and the evaporation of the sweat cools the body. But the results of the experiments cited above indicate that in still air, even with the body at rent, it can not adjust its temperature when the air is above 90° wet- bulb. J. S. Haldane (4) says ""at a wet-bulb temperature of 60°F the actual amount of work done by the miner begins to fall off; as the wet bulb temperature rinse farther the work Bona gradually diminishes to the vanishing point. Then the temperatures indicated by the wet-bulb exceeds 85°F hard work in a mine seems hardly or the commercial working of a mine the wet-bulb thermometer should not in generaI, be allowed to rise above 80°F, unless perhaps where there it a good current."

Dec 1, 1923