Search Documents

By J. C. Gerdeen

SAP-S information on the following element types are included in this appendix: Type 1. Three-Dimensional Truss and Bolt Element Type 4. Two-Dimensional Finite Elements Type 8. Variable-Number-Nodes Thick Shell and Three-Dimensional Elements Type 9. Two-Dimensional Joint Element (to be used with Type 4 elements) Type 10. Three-Dimensional Joint Element (to be used with Type 8 elements) Additional SAP4 elements, Types 2, 3, 5, 6, 7 and 12, are also contained in SAP-S and information on these elements is readily available in any SAP4 user's manual. These elements are as follows: Type 2. Three-Dimensional Beam Elements Type 3. Plane- Stress Membrane I-r .n Elements Type 5. Three-Dimensional Solid Elements (8 Node: Brick) Type 6. Plate and Shell Elements (Quadrilateral) Type 7. Boundary Elements Type 12. Three-Dimensional Straight or Curved Pipe Elements

Jan 1, 1976

By Robert A. Cortese, Henry E. Perlee

Coal dust and float coal dust, produced during normal mining operations, in underground coal mines, are carried from the point of origin downstream by the ventilating air, where it deposits on the surfaces of the mine entry. In an explosion, this dust is lifted from the surfaces by the aerodynamic disturbances and, if of sufficient quantity, can continue to propagate the explosion. To prevent the surface coal dust from contributing, it must be inerted, typically by spreading pulverized limestone, i.e., rock dust, over the coal dust surface. To facilitate the dusting operation, the National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory(PRL), developed an automated system that continuously monitors the accumulation of coal dust. This system could activate a rock-dusting machine that disperses rock dust into the ventilation air when dangerous deposits accumulate and deactivate the machine when sufficient inert has been deposited on top of the coal dust. The system consists of a microprocessor-controlled optical float dust deposition meter. This device measures the light intensity reflected from a deposited layer of dust. A standard cap lamp is used as a fixed-position light source. From the reflected light signal, the microprocessor determines the hazard level of the deposited layer and performs the appropriate action. Full-scale studies conducted in the Experimental Mine at PRL's Lake Lynn Laboratory, using alternating thin layers of rock dust and coal dust, successfully demonstrated the operation of the device. Based on the statistical data from these studies, a mathematical model was developed to predict long-term error in total rock dust content using this inerting procedure. Downwind dust dispersion was also examined to provide optimum placement of the dust sensors and to determine the need for better rock dust dispersion techniques.

Jan 5, 1998

By R. E. Zane

[The Northwest Experiment Station of the Bureau of lines, in cooperation with the College of Mines, University of Washington, has completed a detailed investigation of the physical and chemical properties of western cokes made or used in the Pacific Northwest, as evaluated by standard methods. 4/ One of the chemical properties determined, to which more or less importance has been attached, was reactivity or combustibility. As no standardized procedure is available, it was necessary to develop a workable method for evaluating this property. The combustibility of coke is usually measured by the formation of carbon dioxide with time at a particular temperature or by the reduction of carbon dioxide to carbon monoxide. Analysis of the resulting gases commonly is required to evaluate the result. The method described in this paper is simple and direct in that the sample of coke or other carbonaceous material is weighed as it burns; the loss in weight and time is indicated by a balance and clock arrangement. Gas analyses are not rewired. Methods similar in principle have been used by Tu, Davis, and Hottel6/ and by Oshima and Fukuda7/ for determining the combustion rate of carbon and for studying the effect of ash on combustion characteristics. Both methods: are more elaborate in procedure and apparatus required than teat described here. Brief the method comprises burning a sample of coarsely grained. coke or]

Jan 1, 1940

By K. P. V. Lei

The Bureau of Mines investigated molten-salt electrorefining as a practical method for reclaiming vanadium from vanadium scrap. An electrolytic process utilizing a KC1-LiC1-VC12 electrolyte at 615° C was developed for producing ductile vanadium with a purity over 99.9 percent. The recovery of the vanadium in the cell feed ranged from 88 to 93 percent with a current efficiency from 83 to 95 percent.

Jan 1, 1967

By Terry S. Cory

This report describes the results of a measurement and analysis program to characterize wireless radio transmission In metal/non-metal mines over a wide frequency range from 0.2 -1000 MHz and over a variety of mine environments. Six mines were chosen based on the relative economic significance of their product to the U.S. economy. Mine types Include 01 f shale, uranium, potash, lead/zinc, copper, and silver. Particular mines were chosen so that the group would embody the most Important mining techniques. The results show that transmission at medium frequencies are optimum tor wireless mine communications, In agreement with extensive testing previously performed by the authors in coal mines, and that mine-wide wireless systems are feasible with a minimum requirement for new dedicated wiring. At least one need for such a wireless system was identified in each mine visited.

Jan 1, 1981

By Dhanesh Chandra

[The U.S. Ucparunent of tlIe III LeriOr, Bureau of 1?Ilnes, lnta dcvcltil- (I a m.?tl,nd to extract nickel, i:ob.tll and IlIIicr Valuc:l,1, mrl?tl., lrom I.ow grad:, dumusI it Inlet itc.: :isin;; a rarb-i mnnnxid:: reducl.iun and ,innnonln/mumonlum sull,h.Ito Icitcll Col lowed by solved. evil let foil and clot tr:,winnfu,;. 'I 'o rain bcLtur undcI'sLandin;; uI the producLs reduced rind leached with the s;:Item, the liureau of t?Ilite; was enf,ngod In a 1 uinL sl.utly IIt1I the Uuttvcr ltc~:c:n-ch LnstiI-IL-. 'I'hr'ut;;h C(Im:drlod ahplit I¬L ion:; of a rotnbIW)L11nl ill eleu Lyon :utJ uplical inicrnscopy, cle trun beau micru,inal?;st?s and X-r.iv tcchnitlaes, Lhc factors jilt] ucncing low nickul e::lracl.on yLrids Iron, ccrlnin l;tteritos wul the hcuefhe al yCferL front addil.I:un u1. r:u)plowt' ruug,ounus and halides have bucn rrvealod. IL leas ht'en shown their nt nliJcrate Lion terlperuLuri's (5S0°C - 6501C) Lhe 111LACl extraction ylolds were low hccausc of the futmetlt-m of rufrill t,urv sillc:Ite compicxcs during ciii lit Hi [hut COOL.tlu sig nlficnnt anutunls of nickel .Lrui LhaL arc resistant Lu discolullull it, a su6r.C?quent ammnnlIca1 Jcaeh. 'This formation ill rulracLorv rnngtieves is altrlbuU?d Lo the prc.srnCV of aluauinum combined with c.ilicun jn addlt.lon In tnnl;neni~im in I.lic Lalerites, Iligb exII.Ictlon yields were oblalneJ when none or only a few I ,fraCLot' e, were InrmeJ. Hit s;intc rcfrarlnry cowl, Icxc5 also lend Lo surround Ow IaaIIiable meI.allle iron-IIIcI:el :iILoy CIUSisling ill the mau'ix, tIll: rrhv nreveu)Ling cuntacr ,Itlt LI5U Jeacl: solution; this, huwrvcr, ran ho ovu:rcoml by At ti itlon .111.11 retieCtiun. 'I'hc eIIcc l of prr.reJIctlun .,Ill itivi's vucli i's lye iii', ',udlum "Ill orIde, hv,Irogrn CIIInrILIC, etc., and Lht? 1111,Lre:InrLlI'll he'e:tleg un Lbe cxLt,icLitin are also iilsr.ussod 111 Lhe rcl,olt.]

Jan 1, 1979

By Roger L. Baer

Marine disposal of mill tailings has been practiced worldwide for over a century. However, only recently have the environmental effects of marine disposal been systematically studied. Some early attempts at marine disposal of tailings resulted in adverse impacts to marine life. However, recent advances in tailings disposal methods have included the introduction of engineered submarine tailings discharge systems, advanced environmental assessment and monitoring methods, and oceanographic modeling systems. Successful submarine tailings disposal (STD) has occurred at several mines. The U.S. Bureau of Mines (BOM) has undertaken studies of the disposal of mining and milling wastes in the marine environment. The BOM Alaska Field Operations Center, Juneau, initiated a review of the technology, regulations, and economic aspects of STD. The review illuminated the need for organization of literature on the subject, therefore the Bureau compiled this extensive bibliography on marine disposal of mill tailings. The bibliography presented here contains 1483 references and is also available through diskette in the Word Perfects format. A review of the references indicates that literature on submarine disposal inadequately covers the subject. The majority of the references listed only peripherally relate to the subject. Published literature on the engineering and environmental aspects of STD is severely limited.

Jan 1, 2011

By Paul S. Goodman

Volume II The purpose of this study is to explain reasons for the productivity differences in mining crews. The literature on group productivity is examined. Then a new approach to estimating productivity differences is proposed and estimated across seven different mines. The results indicate a fairly robust model in terms of explanatory power. Recommendations on how the model can be used as a managerial tool are presented.

Jan 1, 1985

By F. E. Spencer

Calculated equilibrium data are presented for three phases in the flue gas stream from a hypothetical open cycle MHD generator. A typical coal is "burned" with 1.0 gram-mole K2O seed per kilogram coal and with 101 percent of stoichiometric air. Tables of composition and the overt thermodynamic properties, enthalpy and entropy, are given for the temperatures 2200 (-100) 1100 kelvins, pressures 1.0 and 1.5 atmospheres, and slag rejection figures of 90 and 75 percent.

Jan 1, 1973

This chapter summarizes data on crude mineral production for the United States, its island possessions, and the Common- wealth of Puerto Rico. Included also are tables that show the principal mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables 'were derived are contained in the individual commodity chapters of volume I and in the State chapters of volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the production of auxiliary processing at or near the mines.

Jan 1, 1978

By Mary Cocklan-Vendl

Regulatory processes associated with development of a world class lead-zinc mine, Red Dog Mine, in northwestern Alaska were reviewed and evaluated. Informal interviews with key project personnel, consultants, and agency field and permitting specialists provided perspective on the regulatory successes and failures of the project. Due to potential impacts to air quality, water quality, wetlands, and National Park lands, an Environmental Impact Statement was required. By developing a comprehensive baseline of information on the existing environment to aid in minimizing impacts during project siting/design and through regular coordination of evolving project plans with regulatory agencies, the mine developers were able to acquire necessary permits in a timely and cost effective manner. The only major exceptions occurred when inadequate information was collected on dispersal of airborne particulates, rates of surface water run-off, and groundwater quality. These deficiencies resulted in the need for design changes, unscheduled construction, additional environmental monitoring costs, and delays in issuance of the NPDES permit.

Jan 1, 1992

By Ronald Branstetter

Gaseous and particulate exhaust emissions from 20 diesel engines in service at five underground mines were measured with high accuracy instrumentation. The engines that were tested were checked for faults or maladjustments. The vehicle and engine maintenance organization was studied at each mine and an idealized maintenance program was devised. Faults were induced in a new diesel engine to determine their effect on the characteristics of the exhaust emissions. The results, conclusions and recommendations from this investigation are presented in this final report.

Jan 1, 1983

By Stephen H. E. Phillips

This report outlines the modifications that have been carried out to the original prototype rectangular shaft sinking equipment for its use in a circular shaft. The surface testing of the machine is described where seven, 24 ft. diameter shafts were excavated to an average depth of 21 ft. at rates ranging between 1 ft/hr and 1.9 ft/hr depending upon the prevailing conditions. The durability and productivity standards for the equipment were established indicating that the objectives of the project had been realized. That is, when using the machine the sinking rates could be increased by 25% and costs reduced by a corresponding amount compared with conventional drill and blast methods. In addition it was shown that the machine had been developed to a state of fitness for sustained underground use.

Jan 1, 1981

By F. S. Kendorski

This report presents the results of a program to improve, using existing and proven technology, unstable highwall conditions through better blasting practices in Appalachian strip coal mines. Better borehole blasting agent distribution and optimization of burden, spacing, and delay periods allowing satisfactory breakage with minimal backbreak were the objectives. At a selected field site, geologic conditions were closely examined with regard to joint orientation and spacing, and resulting slope stability considerations. A test series of eight blasts was completed and the resultant highwall monitored by repetitive photography. The study of drilling and blasting economics along with equipment performance led to an economic model of blast parameters and the identification of blast design cost benefits. The work demonstrated that small strip mining companies' are able to achieve a more stable highwall excavation utilizing presently available technology, equipment, and explosive products at improved operational cost and safety.

Jan 1, 1981

By P. M. Daling

This report, sponsored by the U.S. Bureau of mines, presents the results of an examination of available safety assessment methods and their applicability to the mining industry. Standard safety analysis procedures were evaluated for relevance to the mining industry and mire operators' needs. The major safety concerns and needs of mine operators were identified through telephone contacts and a visit to a mine site. Safety assessment methods recommended for use by the mining Industry were also investigated for potential adaptability to a user-interactive computer system. Several methods were determined to be Immediately transferrable to the mining industry; these techniques are described in a user's handbook produced as part of this project. The handbook gives detailed instructions on appropriate application and utilization of these methods. Other techniques will require further development before they can be effectively transferred to the mining Industry. These methods, their advantages, disadvantages and resource requirements are described in the final project report. Recommended system safety analysis techniques facilitate an evaluation of total mine system safety and a determination of safety-related interactions among systems within a mine. The application of these methods to the mining industry could result In reductions in both the frequency and the consequences of mine accidents.

Jan 1, 1983

By R. Karl Zipf, Z. T. Bieniawski

"Fracture mechanics plays an important role in studies of geologic materials such as rock and coal. Yet fracture data are scarce for rock and most limited or unreliable for coal. A testing system was developed which can apply mixed mode loads to a crack tip in many rocks and geologic materials. It is possible to subject the test specimen to pure mode I, various mixed modes and a nearly pure mode II fracture load. The system is currently used to study the mechanics of fine fragment formation in various coals. Experimental measurements include KI and KII' fracture velocity and acoustic emission.INTRODUCTIONA major research program at The Pennsylvania State University is directed to understanding the fundamental mechanics of fine fragment formation in various coals. The program represents an effort to reduce the incidence of coal workers pneumoconiosis (black lung) in coal miners. The principal source of the respirable coal fragments is the cutting operation which forms and liberates the particles by a fracture process. Present understanding of the mechanics of the events which form and liberate these particles is meager (Cook, 1982).Current knowledge of the fundamental mechanisms of coal dust generation and entrainment in terms of the underlying fracture mechanics is critically needed to improve and possibly control the processes involved. Whether the cutting operation is done with a 'continuous miner' cutting machine, a plow or a longwall shearer, it is fundamentally a problem of mixed-mode crack propagation. When a cutting tool interacts with coal, it causes numerous cracks to propagate through the intact material. Numerous larger fragments are broken free, but another quantity of undesirable fine fragments is also created. The formation of these respirable fragments may be a direct result of the crack propagation process; hence, a thorough understanding of the fracture mechanics of coal is required to minimize production of the unwanted fine fragments.In most rock engineering applications, the rock material properties are of secondary importance to the rock mass properties; however, for rock fragmentation and rock cutting problems, it is rock material properties such as fracture toughness which are of prime interest (Bieniawski, 1980). Several rock cutting and rock failure theories have been proposed, but it is only very recently that fracture mechanics concepts have been successfully applied to the study of rock cutting mechanics. All cutting models seek to predict the cutting forces and the cutter geometry necessary to cause rock breakage and chip formation given some fundamental mechanical properties ~f the rock. Such models have wide applications in drilling, tunnel boring and mining problems. Nelson et al., (1985, 1986) has provided a very useful correlation between the laboratory measured fracture mechanics properties of rock and the performance of the disk cutters on tunnel boring machines."

Jan 1, 1989

By Fred N. Kissell

In This Chapter [Ventilation and methane sampling guidelines for conventional shafts Dealing with restricted spaces where methane can accumulate Ventilation and methane sampling at raise bore drills and Filling shafts at closed coal mines] It is not unusual to encounter methane gas during shaft excavation or shaft-filling operations. Shafts into coalbeds usually produce the most methane, so the information in this chapter applies primarily to shafts at coal mines. Nevertheless, much of the information is relevant for noncoal mines that have methane in the mine or in the overlying strata. METHANE IN SHAFTS EXCAVATED BY CONVENTIONAL MEANS (DRILL, BLAST, MUCK) [ ] Ventilation. Shafts excavated by conventional means are ventilated with a fan on the surface connected to ductwork that extends down into the shaft (Figure 9–1). Shafts into coalbeds should have ventilation systems designed to handle the higher gas flows to be expected as the shaft excavation passes through any over-lying gas-containing strata and nears the coal-bed to be mined. Following are some simple ventilation guidelines for the minimum amount of air required and the selection of the ventilation duct: • Provide enough air to meet the mini-mum OSHA tunnel requirement of 30 ft/min air velocity in the open shaft, as specified in 29 CFR2 1926.800(k)(3). For example, a 20-ft-diam shaft having

Jan 6, 2006

By Philip W. Holland

This Bureau of Mines report discusses the results of three independent reconnaissance geochemical surveys conducted in the vicinity of the Bush Dome reservoir in the Bureau-owned Cliffside field near Amarillo, Tex. The surveys consisted of (1) determining the helium content of area ground waters, (2) determining the helium content of area soil gases and ground waters, and (3) determining the helium content of soil gases collected on a grid sampling pat- tern in the Cliffside field area. The native natural gas in the Cliffside field contains about 1.8 percent helium. To date, approximately 54 billion cubic feet of gas containing approximately 39 billion cubic feet of helium has been injected into the center of the Bush Dome structure. The research work, which was completed under contracts, was done to determine if helium concentration levels in ground water and soil gas could he used as an indication of the presence of helium in a subsurface natural gas accumulation. Results of the surveys were positive in that helium-in-water and helium-in- soil-gas anomalies were detected in portions of the Cliffside field area. All helium analyses were performed by mass spectrometric techniques.

Jan 1, 1979

By William G. Pariseau

A brief description of a two-dimensional elastic-plastic finite element program intended for mine stability analysis is presented that includes detailed instruction for input data preparation and how to obtain output.

Jan 1, 1978

By N. Barton

Large scale tests were conducted on quartzitic gravel and crushed sand-stone to investigate pertinent geotechnical properties for backfill support of egress shafts. Such shafts are envisaged for rapid launching of deep-based missiles. The backfill support is designed to resist shaft closure under dynamic loading, and must also drain rapidly to a lower catch chamber to allow launching. Large scale tilt shear tests were performed to measure the internal shear strength of the two backfill materials. Shaft filling and emptying tests were conducted in a 12 ft deep, 3 ft diameter model section of shaft drilled in sandstone. One half of the model was smooth bored, the other half rough-surfaced to represent drill and blast surfaces. Vertical and horizontal pressure cells indicated that stress only built-up during the first 1 to 1 ½ diameters of filling, due to the high-sidewall friction of 38° for the rough shaft and 31° for the smooth shaft. Interface sliding tests were performed to confirm these figures. Static and dynamic deformation tests were also per-formed, and indicated moduli as high as 56,000 psi, which will give excellent shaft support. Both the shaft support characteristics and the ease of emptying of gravel look particularly promising.

Jan 1, 1983